| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When recently adding the missing 'regulator-allowed-modes' properties it
appears that the binding example with its four-spaces indentation
(corresponding to a single tab, which is still to little) was copied
verbatim.
Drop the unnecessary first line break after 'regulator-allowed-modes'
properties and indent the single remaining continuation line properly.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116102054.4673-3-johan+linaro@kernel.org
|
|
Use the generic samsung,s6sy761 touchscreen driver for this device,
together with a few pins and regulators to power it up correctly.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-10-marijn.suijten@somainline.org
|
|
Enable QUP and GPI DMA hardware to be able to add functioning I2C nodes
later.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-9-marijn.suijten@somainline.org
|
|
Without power the SDCard slot / hardware remains dormant.
Like many other platforms these regulators are used exclusively by
SDHCI, and have their maximum voltage decreased to what downstream sets
on the consumer side. Additionally the SDHCI driver supports setting a
load, for which the regulator definition is extended much the same.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-8-marijn.suijten@somainline.org
|
|
This regulator configuration was adopted from downstream, and is
identical to the sm7225 FairPhone 4 configuration bar pm6350_l8a.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-7-marijn.suijten@somainline.org
|
|
Include pm6350 to inherit its GPIO and button configuration, and
configure "resin" to serve as volume up, and gpio2 as volume down.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-6-marijn.suijten@somainline.org
|
|
In addition to the sdc2 pins, set the SD Card Detect pin in a sane state
to be used as an interrupt when an SD Card is slotted in or removed.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221030073232.22726-4-marijn.suijten@somainline.org
|
|
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Qualcomm ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net> # msm8916
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016102025.23346-4-arnaud.ferraris@collabora.com
|
|
Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.
The bootloader is VERY unpleasant, to get a bootable setup you have to run:
mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img
adb reboot bootloader
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img
fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-16-konrad.dybcio@somainline.org
|
