summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/mesh.h
blob: f70181acceac68ca61a93e056ef33648fafffaae (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
/* SPDX-License-Identifier: GPL-2.0 */
/*
 * mesh.h: definitions for the driver for the MESH SCSI bus adaptor
 * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
 *
 * Copyright (C) 1996 Paul Mackerras.
 */
#ifndef _MESH_H
#define _MESH_H

struct mesh_cmd_priv {
	int this_residual;
	int message;
	int status;
};

static inline struct mesh_cmd_priv *mesh_priv(struct scsi_cmnd *cmd)
{
	return scsi_cmd_priv(cmd);
}

/*
 * Registers in the MESH controller.
 */

struct mesh_regs {
	unsigned char	count_lo;
	char pad0[15];
	unsigned char	count_hi;
	char pad1[15];
	unsigned char	fifo;
	char pad2[15];
	unsigned char	sequence;
	char pad3[15];
	unsigned char	bus_status0;
	char pad4[15];
	unsigned char	bus_status1;
	char pad5[15];
	unsigned char	fifo_count;
	char pad6[15];
	unsigned char	exception;
	char pad7[15];
	unsigned char	error;
	char pad8[15];
	unsigned char	intr_mask;
	char pad9[15];
	unsigned char	interrupt;
	char pad10[15];
	unsigned char	source_id;
	char pad11[15];
	unsigned char	dest_id;
	char pad12[15];
	unsigned char	sync_params;
	char pad13[15];
	unsigned char	mesh_id;
	char pad14[15];
	unsigned char	sel_timeout;
	char pad15[15];
};

/* Bits in the sequence register. */
#define SEQ_DMA_MODE	0x80	/* use DMA for data transfer */
#define SEQ_TARGET	0x40	/* put the controller into target mode */
#define SEQ_ATN		0x20	/* assert ATN signal */
#define SEQ_ACTIVE_NEG	0x10	/* use active negation on REQ/ACK */
#define SEQ_CMD		0x0f	/* command bits: */
#define SEQ_ARBITRATE	1	/*  get the bus */
#define SEQ_SELECT	2	/*  select a target */
#define SEQ_COMMAND	3	/*  send a command */
#define SEQ_STATUS	4	/*  receive status */
#define SEQ_DATAOUT	5	/*  send data */
#define SEQ_DATAIN	6	/*  receive data */
#define SEQ_MSGOUT	7	/*  send a message */
#define SEQ_MSGIN	8	/*  receive a message */
#define SEQ_BUSFREE	9	/*  look for bus free */
#define SEQ_ENBPARITY	0x0a	/*  enable parity checking */
#define SEQ_DISPARITY	0x0b	/*  disable parity checking */
#define SEQ_ENBRESEL	0x0c	/*  enable reselection */
#define SEQ_DISRESEL	0x0d	/*  disable reselection */
#define SEQ_RESETMESH	0x0e	/*  reset the controller */
#define SEQ_FLUSHFIFO	0x0f	/*  clear out the FIFO */

/* Bits in the bus_status0 and bus_status1 registers:
   these correspond directly to the SCSI bus control signals. */
#define BS0_REQ		0x20
#define BS0_ACK		0x10
#define BS0_ATN		0x08
#define BS0_MSG		0x04
#define BS0_CD		0x02
#define BS0_IO		0x01
#define BS1_RST		0x80
#define BS1_BSY		0x40
#define BS1_SEL		0x20

/* Bus phases defined by the bits in bus_status0 */
#define BS0_PHASE	(BS0_MSG+BS0_CD+BS0_IO)
#define BP_DATAOUT	0
#define BP_DATAIN	BS0_IO
#define BP_COMMAND	BS0_CD
#define BP_STATUS	(BS0_CD+BS0_IO)
#define BP_MSGOUT	(BS0_MSG+BS0_CD)
#define BP_MSGIN	(BS0_MSG+BS0_CD+BS0_IO)

/* Bits in the exception register. */
#define EXC_SELWATN	0x20	/* (as target) we were selected with ATN */
#define EXC_SELECTED	0x10	/* (as target) we were selected w/o ATN */
#define EXC_RESELECTED	0x08	/* (as initiator) we were reselected */
#define EXC_ARBLOST	0x04	/* we lost arbitration */
#define EXC_PHASEMM	0x02	/* SCSI phase mismatch */
#define EXC_SELTO	0x01	/* selection timeout */

/* Bits in the error register */
#define ERR_UNEXPDISC	0x40	/* target unexpectedly disconnected */
#define ERR_SCSIRESET	0x20	/* SCSI bus got reset on us */
#define ERR_SEQERR	0x10	/* we did something the chip didn't like */
#define ERR_PARITY	0x01	/* parity error was detected */

/* Bits in the interrupt and intr_mask registers */
#define INT_ERROR	0x04	/* error interrupt */
#define INT_EXCEPTION	0x02	/* exception interrupt */
#define INT_CMDDONE	0x01	/* command done interrupt */

/* Fields in the sync_params register */
#define SYNC_OFF(x)	((x) >> 4)	/* offset field */
#define SYNC_PER(x)	((x) & 0xf)	/* period field */
#define SYNC_PARAMS(o, p)	(((o) << 4) | (p))
#define ASYNC_PARAMS	2	/* sync_params value for async xfers */

/*
 * Assuming a clock frequency of 50MHz:
 *
 * The transfer period with SYNC_PER(sync_params) == x
 * is (x + 2) * 40ns, except that x == 0 gives 100ns.
 *
 * The units of the sel_timeout register are 10ms.
 */


#endif /* _MESH_H */