path: root/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c

// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
/*
 * Copyright (C) 2017 Intel Deutschland GmbH
 * Copyright (C) 2018-2020 Intel Corporation
 */
#include "iwl-trans.h"
#include "iwl-prph.h"
#include "iwl-context-info.h"
#include "iwl-context-info-gen3.h"
#include "internal.h"
#include "fw/dbg.h"

#define FW_RESET_TIMEOUT (HZ / 5)

/*
 * Start up NIC's basic functionality after it has been reset
 * (e.g. after platform boot, or shutdown via iwl_pcie_apm_stop())
 * NOTE:  This does not load uCode nor start the embedded processor
 */
int iwl_pcie_gen2_apm_init(struct iwl_trans *trans)
{
	int ret = 0;

	IWL_DEBUG_INFO(trans, "Init card's basic functions\n");

	/*
	 * Use "set_bit" below rather than "write", to preserve any hardware
	 * bits already set by default after reset.
	 */

	/*
	 * Disable L0s without affecting L1;
	 * don't wait for ICH L0s (ICH bug W/A)
	 */
	iwl_set_bit(trans, CSR_GIO_CHICKEN_BITS,
		    CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);

	/* Set FH wait threshold to maximum (HW error during stress W/A) */
	iwl_set_bit(trans, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);

	/*
	 * Enable HAP INTA (interrupt from management bus) to
	 * wake device's PCI Express link L1a -> L0s
	 */
	iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
		    CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A);

	iwl_pcie_apm_config(trans);

	ret = iwl_finish_nic_init(trans, trans->trans_cfg);
	if (ret)
		return ret;

	set_bit(STATUS_DEVICE_ENABLED, &trans->status);

	return 0;
}

static void iwl_pcie_gen2_apm_stop(struct iwl_trans *trans, bool op_mode_leave)
{
	IWL_DEBUG_INFO(trans, "Stop card, put in low power state\n");

	if (op_mode_leave) {
		if (!test_bit(STATUS_DEVICE_ENABLED, &trans->status))
			iwl_pcie_gen2_apm_init(trans);

		/* inform ME that we are leaving */
		iwl_set_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG,
			    CSR_RESET_LINK_PWR_MGMT_DISABLED);
		iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
			    CSR_HW_IF_CONFIG_REG_PREPARE |
			    CSR_HW_IF_CONFIG_REG_ENABLE_PME);
		mdelay(1);
		iwl_clear_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG,
			      CSR_RESET_LINK_PWR_MGMT_DISABLED);
		mdelay(5);
	}

	clear_bit(STATUS_DEVICE_ENABLED, &trans->status);

	/* Stop device's DMA activity */
	iwl_pcie_apm_stop_master(trans);

	iwl_trans_sw_reset(trans);

	/*
	 * Clear "initialization complete" bit to move adapter from
	 * D0A* (powered-up Active) --> D0U* (Uninitialized) state.
	 */
	iwl_clear_bit(trans, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
}

static void iwl_trans_pcie_fw_reset_handshake(struct iwl_trans *trans)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
	int ret;

	trans_pcie->fw_reset_done = false;

	if (trans->trans_cfg->device_family < IWL_DEVICE_FAMILY_AX210)
		iwl_write_umac_prph(trans, UREG_NIC_SET_NMI_DRIVER,
				    UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE);
	else
		iwl_write_umac_prph(trans, UREG_DOORBELL_TO_ISR6,
				    UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE);

	/* wait 200ms */
	ret = wait_event_timeout(trans_pcie->fw_reset_waitq,
				 trans_pcie->fw_reset_done, FW_RESET_TIMEOUT);
	if (!ret)
		IWL_ERR(trans,
			"firmware didn't ACK the reset - continue anyway\n");
}

void _iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);

	lockdep_assert_held(&trans_pcie->mutex);

	if (trans_pcie->is_down)
		return;

	if (trans_pcie->fw_reset_handshake &&
	    trans->state >= IWL_TRANS_FW_STARTED)
		iwl_trans_pcie_fw_reset_handshake(trans);

	trans_pcie->is_down = true;

	/* tell the device to stop sending interrupts */
	iwl_disable_interrupts(trans);

	/* device going down, Stop using ICT table */
	iwl_pcie_disable_ict(trans);

	/*
	 * If a HW restart happens during firmware loading,
	 * then the firmware loading might call this function
	 * and later it might be called again due to the
	 * restart. So don't process again if the device is
	 * already dead.
	 */
	if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
		IWL_DEBUG_INFO(trans,
			       "DEVICE_ENABLED bit was set and is now cleared\n");
		iwl_txq_gen2_tx_stop(trans);
		iwl_pcie_rx_stop(trans);
	}

	iwl_pcie_ctxt_info_free_paging(trans);
	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)
		iwl_pcie_ctxt_info_gen3_free(trans);
	else
		iwl_pcie_ctxt_info_free(trans);

	/* Make sure (redundant) we've released our request to stay awake */
	iwl_clear_bit(trans, CSR_GP_CNTRL,
		      CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);

	/* Stop the device, and put it in low power state */
	iwl_pcie_gen2_apm_stop(trans, false);

	iwl_trans_sw_reset(trans);

	/*
	 * Upon stop, the IVAR table gets erased, so msi-x won't
	 * work. This causes a bug in RF-KILL flows, since the interrupt
	 * that enables radio won't fire on the correct irq, and the
	 * driver won't be able to handle the interrupt.
	 * Configure the IVAR table again after reset.
	 */
	iwl_pcie_conf_msix_hw(trans_pcie);

	/*
	 * Upon stop, the APM issues an interrupt if HW RF kill is set.
	 * This is a bug in certain verions of the hardware.
	 * Certain devices also keep sending HW RF kill interrupt all
	 * the time, unless the interrupt is ACKed even if the interrupt
	 * should be masked. Re-ACK all the interrupts here.
	 */
	iwl_disable_interrupts(trans);

	/* clear all status bits */
	clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status);
	clear_bit(STATUS_INT_ENABLED, &trans->status);
	clear_bit(STATUS_TPOWER_PMI, &trans->status);

	/*
	 * Even if we stop the HW, we still want the RF kill
	 * interrupt
	 */
	iwl_enable_rfkill_int(trans);

	/* re-take ownership to prevent other users from stealing the device */
	iwl_pcie_prepare_card_hw(trans);
}

void iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
	bool was_in_rfkill;

	iwl_op_mode_time_point(trans->op_mode,
			       IWL_FW_INI_TIME_POINT_HOST_DEVICE_DISABLE,
			       NULL);

	mutex_lock(&trans_pcie->mutex);
	trans_pcie->opmode_down = true;
	was_in_rfkill = test_bit(STATUS_RFKILL_OPMODE, &trans->status);
	_iwl_trans_pcie_gen2_stop_device(trans);
	iwl_trans_pcie_handle_stop_rfkill(trans, was_in_rfkill);
	mutex_unlock(&trans_pcie->mutex);
}

static int iwl_pcie_gen2_nic_init(struct iwl_trans *trans)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
	int queue_size = max_t(u32, IWL_CMD_QUEUE_SIZE,
			       trans->cfg->min_txq_size);

	/* TODO: most of the logic can be removed in A0 - but not in Z0 */
	spin_lock_bh(&trans_pcie->irq_lock);
	iwl_pcie_gen2_apm_init(trans);
	spin_unlock_bh(&trans_pcie->irq_lock);

	iwl_op_mode_nic_config(trans->op_mode);

	/* Allocate the RX queue, or reset if it is already allocated */
	if (iwl_pcie_gen2_rx_init(trans))
		return -ENOMEM;

	/* Allocate or reset and init all Tx and Command queues */
	if (iwl_txq_gen2_init(trans, trans->txqs.cmd.q_id, queue_size))
		return -ENOMEM;

	/* enable shadow regs in HW */
	iwl_set_bit(trans, CSR_MAC_SHADOW_REG_CTRL, 0x800FFFFF);
	IWL_DEBUG_INFO(trans, "Enabling shadow registers in device\n");

	return 0;
}

void iwl_trans_pcie_gen2_fw_alive(struct iwl_trans *trans, u32 scd_addr)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);

	iwl_pcie_reset_ict(trans);

	/* make sure all queue are not stopped/used */
	memset(trans->txqs.queue_stopped, 0,
	       sizeof(trans->txqs.queue_stopped));
	memset(trans->txqs.queue_used, 0, sizeof(trans->txqs.queue_used));

	/* now that we got alive we can free the fw image & the context info.
	 * paging memory cannot be freed included since FW will still use it
	 */
	iwl_pcie_ctxt_info_free(trans);

	/*
	 * Re-enable all the interrupts, including the RF-Kill one, now that
	 * the firmware is alive.
	 */
	iwl_enable_interrupts(trans);
	mutex_lock(&trans_pcie->mutex);
	iwl_pcie_check_hw_rf_kill(trans);
	mutex_unlock(&trans_pcie->mutex);
}

static void iwl_pcie_set_ltr(struct iwl_trans *trans)
{
	u32 ltr_val = CSR_LTR_LONG_VAL_AD_NO_SNOOP_REQ |
		      u32_encode_bits(CSR_LTR_LONG_VAL_AD_SCALE_USEC,
				      CSR_LTR_LONG_VAL_AD_NO_SNOOP_SCALE) |
		      u32_encode_bits(250,
				      CSR_LTR_LONG_VAL_AD_NO_SNOOP_VAL) |
		      CSR_LTR_LONG_VAL_AD_SNOOP_REQ |
		      u32_encode_bits(CSR_LTR_LONG_VAL_AD_SCALE_USEC,
				      CSR_LTR_LONG_VAL_AD_SNOOP_SCALE) |
		      u32_encode_bits(250, CSR_LTR_LONG_VAL_AD_SNOOP_VAL);

	/*
	 * To workaround hardware latency issues during the boot process,
	 * initialize the LTR to ~250 usec (see ltr_val above).
	 * The firmware initializes this again later (to a smaller value).
	 */
	if ((trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_AX210 ||
	     trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_22000) &&
	    !trans->trans_cfg->integrated) {
		iwl_write32(trans, CSR_LTR_LONG_VAL_AD, ltr_val);
	} else if (trans->trans_cfg->integrated &&
		   trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_22000) {
		iwl_write_prph(trans, HPM_MAC_LTR_CSR, HPM_MAC_LRT_ENABLE_ALL);
		iwl_write_prph(trans, HPM_UMAC_LTR, ltr_val);
	}
}

int iwl_trans_pcie_gen2_start_fw(struct iwl_trans *trans,
				 const struct fw_img *fw, bool run_in_rfkill)
{
	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
	bool hw_rfkill;
	int ret;

	/* This may fail if AMT took ownership of the device */
	if (iwl_pcie_prepare_card_hw(trans)) {
		IWL_WARN(trans, "Exit HW not ready\n");
		ret = -EIO;
		goto out;
	}

	iwl_enable_rfkill_int(trans);

	iwl_write32(trans, CSR_INT, 0xFFFFFFFF);

	/*
	 * We enabled the RF-Kill interrupt and the handler may very
	 * well be running. Disable the interrupts to make sure no other
	 * interrupt can be fired.
	 */
	iwl_disable_interrupts(trans);

	/* Make sure it finished running */
	iwl_pcie_synchronize_irqs(trans);

	mutex_lock(&trans_pcie->mutex);

	/* If platform's RF_KILL switch is NOT set to KILL */
	hw_rfkill = iwl_pcie_check_hw_rf_kill(trans);
	if (hw_rfkill && !run_in_rfkill) {
		ret = -ERFKILL;
		goto out;
	}

	/* Someone called stop_device, don't try to start_fw */
	if (trans_pcie->is_down) {
		IWL_WARN(trans,
			 "Can't start_fw since the HW hasn't been started\n");
		ret = -EIO;
		goto out;
	}

	/* make sure rfkill handshake bits are cleared */
	iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
	iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR,
		    CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);

	/* clear (again), then enable host interrupts */
	iwl_write32(trans, CSR_INT, 0xFFFFFFFF);

	ret = iwl_pcie_gen2_nic_init(trans);
	if (ret) {
		IWL_ERR(trans, "Unable to init nic\n");
		goto out;
	}

	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)
		ret = iwl_pcie_ctxt_info_gen3_init(trans, fw);
	else
		ret = iwl_pcie_ctxt_info_init(trans, fw);
	if (ret)
		goto out;

	iwl_pcie_set_ltr(trans);

	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)
		iwl_write_umac_prph(trans, UREG_CPU_INIT_RUN, 1);
	else
		iwl_write_prph(trans, UREG_CPU_INIT_RUN, 1);

	/* re-check RF-Kill state since we may have missed the interrupt */
	hw_rfkill = iwl_pcie_check_hw_rf_kill(trans);
	if (hw_rfkill && !run_in_rfkill)
		ret = -ERFKILL;

out:
	mutex_unlock(&trans_pcie->mutex);
	return ret;
}