summaryrefslogtreecommitdiffstats
path: root/drivers/mmc/host/sdhci-of-at91.c
blob: e377b9bc55a46d293353f3473050cae9b2494027 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
// SPDX-License-Identifier: GPL-2.0-only
/*
 * Atmel SDMMC controller driver.
 *
 * Copyright (C) 2015 Atmel,
 *		 2015 Ludovic Desroches <ludovic.desroches@atmel.com>
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/mmc/host.h>
#include <linux/mmc/slot-gpio.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>

#include "sdhci-pltfm.h"

#define SDMMC_MC1R	0x204
#define		SDMMC_MC1R_DDR		BIT(3)
#define		SDMMC_MC1R_FCD		BIT(7)
#define SDMMC_CACR	0x230
#define		SDMMC_CACR_CAPWREN	BIT(0)
#define		SDMMC_CACR_KEY		(0x46 << 8)

#define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */

struct sdhci_at91_priv {
	struct clk *hclock;
	struct clk *gck;
	struct clk *mainck;
	bool restore_needed;
};

static void sdhci_at91_set_force_card_detect(struct sdhci_host *host)
{
	u8 mc1r;

	mc1r = readb(host->ioaddr + SDMMC_MC1R);
	mc1r |= SDMMC_MC1R_FCD;
	writeb(mc1r, host->ioaddr + SDMMC_MC1R);
}

static void sdhci_at91_set_clock(struct sdhci_host *host, unsigned int clock)
{
	u16 clk;
	unsigned long timeout;

	host->mmc->actual_clock = 0;

	/*
	 * There is no requirement to disable the internal clock before
	 * changing the SD clock configuration. Moreover, disabling the
	 * internal clock, changing the configuration and re-enabling the
	 * internal clock causes some bugs. It can prevent to get the internal
	 * clock stable flag ready and an unexpected switch to the base clock
	 * when using presets.
	 */
	clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
	clk &= SDHCI_CLOCK_INT_EN;
	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);

	if (clock == 0)
		return;

	clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);

	clk |= SDHCI_CLOCK_INT_EN;
	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);

	/* Wait max 20 ms */
	timeout = 20;
	while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
		& SDHCI_CLOCK_INT_STABLE)) {
		if (timeout == 0) {
			pr_err("%s: Internal clock never stabilised.\n",
			       mmc_hostname(host->mmc));
			return;
		}
		timeout--;
		mdelay(1);
	}

	clk |= SDHCI_CLOCK_CARD_EN;
	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
}

/*
 * In this specific implementation of the SDHCI controller, the power register
 * needs to have a valid voltage set even when the power supply is managed by
 * an external regulator.
 */
static void sdhci_at91_set_power(struct sdhci_host *host, unsigned char mode,
		     unsigned short vdd)
{
	if (!IS_ERR(host->mmc->supply.vmmc)) {
		struct mmc_host *mmc = host->mmc;

		mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
	}
	sdhci_set_power_noreg(host, mode, vdd);
}

static void sdhci_at91_set_uhs_signaling(struct sdhci_host *host,
					 unsigned int timing)
{
	if (timing == MMC_TIMING_MMC_DDR52)
		sdhci_writeb(host, SDMMC_MC1R_DDR, SDMMC_MC1R);
	sdhci_set_uhs_signaling(host, timing);
}

static void sdhci_at91_reset(struct sdhci_host *host, u8 mask)
{
	sdhci_reset(host, mask);

	if (host->mmc->caps & MMC_CAP_NONREMOVABLE)
		sdhci_at91_set_force_card_detect(host);
}

static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
	.set_clock		= sdhci_at91_set_clock,
	.set_bus_width		= sdhci_set_bus_width,
	.reset			= sdhci_at91_reset,
	.set_uhs_signaling	= sdhci_at91_set_uhs_signaling,
	.set_power		= sdhci_at91_set_power,
};

static const struct sdhci_pltfm_data soc_data_sama5d2 = {
	.ops = &sdhci_at91_sama5d2_ops,
};

static const struct of_device_id sdhci_at91_dt_match[] = {
	{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
	{}
};
MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);

static int sdhci_at91_set_clks_presets(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
	int ret;
	unsigned int			caps0, caps1;
	unsigned int			clk_base, clk_mul;
	unsigned int			gck_rate, real_gck_rate;
	unsigned int			preset_div;

	/*
	 * The mult clock is provided by as a generated clock by the PMC
	 * controller. In order to set the rate of gck, we have to get the
	 * base clock rate and the clock mult from capabilities.
	 */
	clk_prepare_enable(priv->hclock);
	caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
	caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
	clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
	clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
	gck_rate = clk_base * 1000000 * (clk_mul + 1);
	ret = clk_set_rate(priv->gck, gck_rate);
	if (ret < 0) {
		dev_err(dev, "failed to set gck");
		clk_disable_unprepare(priv->hclock);
		return ret;
	}
	/*
	 * We need to check if we have the requested rate for gck because in
	 * some cases this rate could be not supported. If it happens, the rate
	 * is the closest one gck can provide. We have to update the value
	 * of clk mul.
	 */
	real_gck_rate = clk_get_rate(priv->gck);
	if (real_gck_rate != gck_rate) {
		clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
		caps1 &= (~SDHCI_CLOCK_MUL_MASK);
		caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
			  SDHCI_CLOCK_MUL_MASK);
		/* Set capabilities in r/w mode. */
		writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
		       host->ioaddr + SDMMC_CACR);
		writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
		/* Set capabilities in ro mode. */
		writel(0, host->ioaddr + SDMMC_CACR);
		dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
			 clk_mul, real_gck_rate);
	}

	/*
	 * We have to set preset values because it depends on the clk_mul
	 * value. Moreover, SDR104 is supported in a degraded mode since the
	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
	 * reason, we need to use presets to support SDR104.
	 */
	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);

	clk_prepare_enable(priv->mainck);
	clk_prepare_enable(priv->gck);

	return 0;
}

#ifdef CONFIG_PM_SLEEP
static int sdhci_at91_suspend(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
	int ret;

	ret = pm_runtime_force_suspend(dev);

	priv->restore_needed = true;

	return ret;
}
#endif /* CONFIG_PM_SLEEP */

#ifdef CONFIG_PM
static int sdhci_at91_runtime_suspend(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
	int ret;

	ret = sdhci_runtime_suspend_host(host);

	if (host->tuning_mode != SDHCI_TUNING_MODE_3)
		mmc_retune_needed(host->mmc);

	clk_disable_unprepare(priv->gck);
	clk_disable_unprepare(priv->hclock);
	clk_disable_unprepare(priv->mainck);

	return ret;
}

static int sdhci_at91_runtime_resume(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
	int ret;

	if (priv->restore_needed) {
		ret = sdhci_at91_set_clks_presets(dev);
		if (ret)
			return ret;

		priv->restore_needed = false;
		goto out;
	}

	ret = clk_prepare_enable(priv->mainck);
	if (ret) {
		dev_err(dev, "can't enable mainck\n");
		return ret;
	}

	ret = clk_prepare_enable(priv->hclock);
	if (ret) {
		dev_err(dev, "can't enable hclock\n");
		return ret;
	}

	ret = clk_prepare_enable(priv->gck);
	if (ret) {
		dev_err(dev, "can't enable gck\n");
		return ret;
	}

out:
	return sdhci_runtime_resume_host(host);
}
#endif /* CONFIG_PM */

static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
	SET_SYSTEM_SLEEP_PM_OPS(sdhci_at91_suspend, pm_runtime_force_resume)
	SET_RUNTIME_PM_OPS(sdhci_at91_runtime_suspend,
			   sdhci_at91_runtime_resume,
			   NULL)
};

static int sdhci_at91_probe(struct platform_device *pdev)
{
	const struct of_device_id	*match;
	const struct sdhci_pltfm_data	*soc_data;
	struct sdhci_host		*host;
	struct sdhci_pltfm_host		*pltfm_host;
	struct sdhci_at91_priv		*priv;
	int				ret;

	match = of_match_device(sdhci_at91_dt_match, &pdev->dev);
	if (!match)
		return -EINVAL;
	soc_data = match->data;

	host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
	if (IS_ERR(host))
		return PTR_ERR(host);

	pltfm_host = sdhci_priv(host);
	priv = sdhci_pltfm_priv(pltfm_host);

	priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
	if (IS_ERR(priv->mainck)) {
		dev_err(&pdev->dev, "failed to get baseclk\n");
		return PTR_ERR(priv->mainck);
	}

	priv->hclock = devm_clk_get(&pdev->dev, "hclock");
	if (IS_ERR(priv->hclock)) {
		dev_err(&pdev->dev, "failed to get hclock\n");
		return PTR_ERR(priv->hclock);
	}

	priv->gck = devm_clk_get(&pdev->dev, "multclk");
	if (IS_ERR(priv->gck)) {
		dev_err(&pdev->dev, "failed to get multclk\n");
		return PTR_ERR(priv->gck);
	}

	ret = sdhci_at91_set_clks_presets(&pdev->dev);
	if (ret)
		goto sdhci_pltfm_free;

	priv->restore_needed = false;

	ret = mmc_of_parse(host->mmc);
	if (ret)
		goto clocks_disable_unprepare;

	sdhci_get_of_property(pdev);

	pm_runtime_get_noresume(&pdev->dev);
	pm_runtime_set_active(&pdev->dev);
	pm_runtime_enable(&pdev->dev);
	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
	pm_runtime_use_autosuspend(&pdev->dev);

	ret = sdhci_add_host(host);
	if (ret)
		goto pm_runtime_disable;

	/*
	 * When calling sdhci_runtime_suspend_host(), the sdhci layer makes
	 * the assumption that all the clocks of the controller are disabled.
	 * It means we can't get irq from it when it is runtime suspended.
	 * For that reason, it is not planned to wake-up on a card detect irq
	 * from the controller.
	 * If we want to use runtime PM and to be able to wake-up on card
	 * insertion, we have to use a GPIO for the card detection or we can
	 * use polling. Be aware that using polling will resume/suspend the
	 * controller between each attempt.
	 * Disable SDHCI_QUIRK_BROKEN_CARD_DETECTION to be sure nobody tries
	 * to enable polling via device tree with broken-cd property.
	 */
	if (mmc_card_is_removable(host->mmc) &&
	    mmc_gpio_get_cd(host->mmc) < 0) {
		host->mmc->caps |= MMC_CAP_NEEDS_POLL;
		host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
	}

	/*
	 * If the device attached to the MMC bus is not removable, it is safer
	 * to set the Force Card Detect bit. People often don't connect the
	 * card detect signal and use this pin for another purpose. If the card
	 * detect pin is not muxed to SDHCI controller, a default value is
	 * used. This value can be different from a SoC revision to another
	 * one. Problems come when this default value is not card present. To
	 * avoid this case, if the device is non removable then the card
	 * detection procedure using the SDMCC_CD signal is bypassed.
	 * This bit is reset when a software reset for all command is performed
	 * so we need to implement our own reset function to set back this bit.
	 */
	if (host->mmc->caps & MMC_CAP_NONREMOVABLE)
		sdhci_at91_set_force_card_detect(host);

	pm_runtime_put_autosuspend(&pdev->dev);

	return 0;

pm_runtime_disable:
	pm_runtime_disable(&pdev->dev);
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);
clocks_disable_unprepare:
	clk_disable_unprepare(priv->gck);
	clk_disable_unprepare(priv->mainck);
	clk_disable_unprepare(priv->hclock);
sdhci_pltfm_free:
	sdhci_pltfm_free(pdev);
	return ret;
}

static int sdhci_at91_remove(struct platform_device *pdev)
{
	struct sdhci_host	*host = platform_get_drvdata(pdev);
	struct sdhci_pltfm_host	*pltfm_host = sdhci_priv(host);
	struct sdhci_at91_priv	*priv = sdhci_pltfm_priv(pltfm_host);
	struct clk *gck = priv->gck;
	struct clk *hclock = priv->hclock;
	struct clk *mainck = priv->mainck;

	pm_runtime_get_sync(&pdev->dev);
	pm_runtime_disable(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);

	sdhci_pltfm_unregister(pdev);

	clk_disable_unprepare(gck);
	clk_disable_unprepare(hclock);
	clk_disable_unprepare(mainck);

	return 0;
}

static struct platform_driver sdhci_at91_driver = {
	.driver		= {
		.name	= "sdhci-at91",
		.of_match_table = sdhci_at91_dt_match,
		.pm	= &sdhci_at91_dev_pm_ops,
	},
	.probe		= sdhci_at91_probe,
	.remove		= sdhci_at91_remove,
};

module_platform_driver(sdhci_at91_driver);

MODULE_DESCRIPTION("SDHCI driver for at91");
MODULE_AUTHOR("Ludovic Desroches <ludovic.desroches@atmel.com>");
MODULE_LICENSE("GPL v2");