summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/intel-ixp42x-dlink-dsm-g600.dts
blob: 5ab09fb10dae66f9d6c52d7fdf5653e952aca80d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
// SPDX-License-Identifier: ISC
/*
 * Device Tree file for D-Link DSM-G600 revision A based on IXP420
 * NOTE: revision B of this device uses PowerPC and is NOT supported by
 * this device tree.
 *
 * Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo
 * and Michael Westerhof.
 */

/dts-v1/;

#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>

/ {
	model = "D-Link DSM-G600 rev A";
	compatible = "dlink,dsm-g600-a", "intel,ixp42x";
	#address-cells = <1>;
	#size-cells = <1>;

	memory@0 {
		/* 64 MB SDRAM */
		device_type = "memory";
		reg = <0x00000000 0x4000000>;
	};

	chosen {
		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
		stdout-path = "uart0:115200n8";
	};

	aliases {
		serial0 = &uart0;
	};

	leds {
		compatible = "gpio-leds";
		led-power {
			label = "dsmg600:green:power";
			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
			default-state = "on";
			linux,default-trigger = "heartbeat";
		};
		led-wlan {
			label = "dsmg600:green:wlan";
			/* CHECKME: flagged as active low in the old board file */
			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
			default-state = "on";
			/* We don't have WLAN trigger in the kernel (yet) */
			linux,default-trigger = "netdev";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";

		button-reset {
			wakeup-source;
			linux,code = <KEY_ESC>;
			label = "reset";
			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
		};
	};

	gpio_keys_polled {
		compatible = "gpio-keys-polled";

		/*
		 * According to the board file this key cannot handle interrupts and
		 * need to be polled. Investigate if this is really the case or if
		 * this can be moved adjacent to the ordinary gpio-keys above.
		 */
		button-power {
			wakeup-source;
			linux,code = <KEY_POWER>;
			label = "power";
			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
		};
	};

	i2c {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		#address-cells = <1>;
		#size-cells = <0>;

		rtc@51 {
			compatible = "nxp,pcf8563";
			reg = <0x51>;
		};
	};

	gpio-poweroff {
		compatible = "gpio-poweroff";
		gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
		timeout-ms = <5000>;
	};

	soc {
		bus@c4000000 {
			/* The first 16MB region at CS0 on the expansion bus */
			flash@0,0 {
				compatible = "intel,ixp4xx-flash", "cfi-flash";
				bank-width = <2>;
				/*
				 * 16 MB of Flash in 128 0x20000 sized blocks
				 * mapped in at CS0.
				 */
				reg = <0 0x00000000 0x1000000>;

				partitions {
					compatible = "redboot-fis";
					/*
					 * A boot log says the directory is at 0xfe0000
					 * 0x7f * 0x20000 = 0xfe0000
					 */
					fis-index-block = <0x7f>;
				};
			};
		};

		pci@c0000000 {
			status = "ok";

			/*
			 * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c)
			 * We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3.
			 * Only slot 3 have three IRQs.
			 */
			#interrupt-cells = <1>;
			interrupt-map-mask = <0xf800 0 0 7>;
			interrupt-map =
			/* IDSEL 1 */
			<0x0800 0 0 1 &gpio0 7  IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */
			/* IDSEL 2 */
			<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */
			/* IDSEL 3 */
			<0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */
			<0x1800 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */
			<0x1800 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */
			/* IDSEL 4 */
			<0x2000 0 0 3 &gpio0 6  IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */
		};
	};
};