summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
blob: ec721d323ac5a8734e4a776fc529819813257bb1 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2837.dtsi"
#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-lan7515.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
#include "bcm283x-rpi-wifi-bt.dtsi"

/ {
	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
	model = "Raspberry Pi 3 Model B+";

	chosen {
		/* 8250 auxiliary UART instead of pl011 */
		stdout-path = "serial1:115200n8";
	};

	memory@0 {
		device_type = "memory";
		reg = <0 0x40000000>;
	};

	leds {
		led-act {
			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
		};

		led-pwr {
			label = "PWR";
			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
			default-state = "keep";
			linux,default-trigger = "default-on";
		};
	};
};

&bt {
	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
};

&firmware {
	expgpio: gpio {
		compatible = "raspberrypi,firmware-gpio";
		gpio-controller;
		#gpio-cells = <2>;
		gpio-line-names = "BT_ON",
				  "WL_ON",
				  "PWR_LED_R",
				  "LAN_RUN",
				  "",
				  "CAM_GPIO0",
				  "CAM_GPIO1",
				  "";
		status = "okay";
	};
};

&gpio {
	/*
	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
	 * the official GPU firmware DT blob.
	 *
	 * Legend:
	 * "FOO" = GPIO line named "FOO" on the schematic
	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
	 */
	gpio-line-names = "ID_SDA",
			  "ID_SCL",
			  "SDA1",
			  "SCL1",
			  "GPIO_GCLK",
			  "GPIO5",
			  "GPIO6",
			  "SPI_CE1_N",
			  "SPI_CE0_N",
			  "SPI_MISO",
			  "SPI_MOSI",
			  "SPI_SCLK",
			  "GPIO12",
			  "GPIO13",
			  /* Serial port */
			  "TXD1",
			  "RXD1",
			  "GPIO16",
			  "GPIO17",
			  "GPIO18",
			  "GPIO19",
			  "GPIO20",
			  "GPIO21",
			  "GPIO22",
			  "GPIO23",
			  "GPIO24",
			  "GPIO25",
			  "GPIO26",
			  "GPIO27",
			  "HDMI_HPD_N",
			  "STATUS_LED_G",
			  /* Used by BT module */
			  "CTS0",
			  "RTS0",
			  "TXD0",
			  "RXD0",
			  /* Used by Wifi */
			  "SD1_CLK",
			  "SD1_CMD",
			  "SD1_DATA0",
			  "SD1_DATA1",
			  "SD1_DATA2",
			  "SD1_DATA3",
			  "PWM0_OUT",
			  "PWM1_OUT",
			  "ETH_CLK",
			  "WIFI_CLK",
			  "SDA0",
			  "SCL0",
			  "SMPS_SCL",
			  "SMPS_SDA",
			  /* Used by SD Card */
			  "SD_CLK_R",
			  "SD_CMD_R",
			  "SD_DATA0_R",
			  "SD_DATA1_R",
			  "SD_DATA2_R",
			  "SD_DATA3_R";
};

&hdmi {
	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
	status = "okay";
};

&pwm {
	pinctrl-names = "default";
	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
	status = "okay";
};

/* SDHOST is used to drive the SD card */
&sdhost {
	pinctrl-names = "default";
	pinctrl-0 = <&sdhost_gpio48>;
	status = "okay";
	bus-width = <4>;
};

/* uart0 communicates with the BT module */
&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
};

/* uart1 is mapped to the pin header */
&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_gpio14>;
	status = "okay";
};

&wifi_pwrseq {
	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
};