blob: ffba4f63d71fdebf184effa3aea537f0b8f56dec (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
|
* Mediatek/Ralink RT3883 PCI controller
1) Main node
Required properties:
- compatible: must be "ralink,rt3883-pci"
- reg: specifies the physical base address of the controller and
the length of the memory mapped region.
- #address-cells: specifies the number of cells needed to encode an
address. The value must be 1.
- #size-cells: specifies the number of cells used to represent the size
of an address. The value must be 1.
- ranges: specifies the translation between child address space and parent
address space
Optional properties:
- status: indicates the operational status of the device.
Value must be either "disabled" or "okay".
2) Child nodes
The main node must have two child nodes which describes the built-in
interrupt controller and the PCI host bridge.
a) Interrupt controller:
Required properties:
- interrupt-controller: identifies the node as an interrupt controller
- #address-cells: specifies the number of cells needed to encode an
address. The value must be 0. As such, 'interrupt-map' nodes do not
have to specify a parent unit address.
- #interrupt-cells: specifies the number of cells needed to encode an
interrupt source. The value must be 1.
- interrupts: specifies the interrupt source of the parent interrupt
controller. The format of the interrupt specifier depends on the
parent interrupt controller.
b) PCI host bridge:
Required properties:
- #address-cells: specifies the number of cells needed to encode an
address. The value must be 0.
- #size-cells: specifies the number of cells used to represent the size
of an address. The value must be 2.
- #interrupt-cells: specifies the number of cells needed to encode an
interrupt source. The value must be 1.
- device_type: must be "pci"
- bus-range: PCI bus numbers covered
- ranges: specifies the ranges for the PCI memory and I/O regions
- interrupt-map-mask,
- interrupt-map: standard PCI properties to define the mapping of the
PCI interface to interrupt numbers.
The PCI host bridge node might have additional sub-nodes representing
the onboard PCI devices/PCI slots. Each such sub-node must have the
following mandatory properties:
- reg: used only for interrupt mapping, so only the first four bytes
are used to refer to the correct bus number and device number.
- device_type: must be "pci"
If a given sub-node represents a PCI bridge it must have following
mandatory properties as well:
- #address-cells: must be set to <3>
- #size-cells: must set to <2>
- #interrupt-cells: must be set to <1>
- interrupt-map-mask,
- interrupt-map: standard PCI properties to define the mapping of the
PCI interface to interrupt numbers.
Besides the required properties the sub-nodes may have these optional
properties:
- status: indicates the operational status of the sub-node.
Value must be either "disabled" or "okay".
3) Example:
a) SoC specific dtsi file:
pci@10140000 {
compatible = "ralink,rt3883-pci";
reg = <0x10140000 0x20000>;
#address-cells = <1>;
#size-cells = <1>;
ranges; /* direct mapping */
status = "disabled";
pciintc: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
interrupt-parent = <&cpuintc>;
interrupts = <4>;
};
host-bridge {
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
device_type = "pci";
bus-range = <0 255>;
ranges = <
0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */
0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */
>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <
/* IDSEL 17 */
0x8800 0 0 1 &pciintc 18
0x8800 0 0 2 &pciintc 18
0x8800 0 0 3 &pciintc 18
0x8800 0 0 4 &pciintc 18
/* IDSEL 18 */
0x9000 0 0 1 &pciintc 19
0x9000 0 0 2 &pciintc 19
0x9000 0 0 3 &pciintc 19
0x9000 0 0 4 &pciintc 19
>;
pci-bridge@1 {
reg = <0x0800 0 0 0 0>;
device_type = "pci";
#interrupt-cells = <1>;
#address-cells = <3>;
#size-cells = <2>;
interrupt-map-mask = <0x0 0 0 0>;
interrupt-map = <0x0 0 0 0 &pciintc 20>;
status = "disabled";
};
pci-slot@17 {
reg = <0x8800 0 0 0 0>;
device_type = "pci";
status = "disabled";
};
pci-slot@18 {
reg = <0x9000 0 0 0 0>;
device_type = "pci";
status = "disabled";
};
};
};
b) Board specific dts file:
pci@10140000 {
status = "okay";
host-bridge {
pci-bridge@1 {
status = "okay";
};
};
};
|
