summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml
blob: 7c331bfbe370eb5c61c0ef6a11afd022039c9dc4 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Binding for IDT VersaClock 5 and 6 programmable I2C clock generators

description: |
  The IDT VersaClock 5 and VersaClock 6 are programmable I2C
  clock generators providing from 3 to 12 output clocks.

  When referencing the provided clock in the DT using phandle and clock
  specifier, the following mapping applies:

  - 5P49V5923:
    0 -- OUT0_SEL_I2CB
    1 -- OUT1
    2 -- OUT2

  - 5P49V5933:
    0 -- OUT0_SEL_I2CB
    1 -- OUT1
    2 -- OUT4

  - other parts:
    0 -- OUT0_SEL_I2CB
    1 -- OUT1
    2 -- OUT2
    3 -- OUT3
    4 -- OUT4

  The idt,shutdown and idt,output-enable-active properties control the
  SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown
  Register, respectively. Their behavior is summarized by the following
  table:

  SH SP Output when the SD/OE pin is Low/High
  == == =====================================
   0  0 Active/Inactive
   0  1 Inactive/Active
   1  0 Active/Shutdown
   1  1 Inactive/Shutdown

  The case where SH and SP are both 1 is likely not very interesting.

maintainers:
  - Luca Ceresoli <luca.ceresoli@bootlin.com>

properties:
  compatible:
    enum:
      - idt,5p49v5923
      - idt,5p49v5925
      - idt,5p49v5933
      - idt,5p49v5935
      - idt,5p49v6901
      - idt,5p49v6965

  reg:
    description: I2C device address
    enum: [ 0x68, 0x6a ]

  '#clock-cells':
    const: 1

  clock-names:
    minItems: 1
    maxItems: 2
    items:
      enum: [ xin, clkin ]
  clocks:
    minItems: 1
    maxItems: 2

  idt,xtal-load-femtofarads:
    minimum: 9000
    maximum: 22760
    description: Optional load capacitor for XTAL1 and XTAL2

  idt,shutdown:
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [0, 1]
    description: |
      If 1, this enables the shutdown functionality: the chip will be
      shut down if the SD/OE pin is driven high. If 0, this disables the
      shutdown functionality: the chip will never be shut down based on
      the value of the SD/OE pin. This property corresponds to the SH
      bit of the Primary Source and Shutdown Register.

  idt,output-enable-active:
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [0, 1]
    description: |
      If 1, this enables output when the SD/OE pin is high, and disables
      output when the SD/OE pin is low. If 0, this disables output when
      the SD/OE pin is high, and enables output when the SD/OE pin is
      low. This corresponds to the SP bit of the Primary Source and
      Shutdown Register.

patternProperties:
  "^OUT[1-4]$":
    type: object
    description:
      Description of one of the outputs (OUT1..OUT4). See "Clock1 Output
      Configuration" in the Versaclock 5/6/6E Family Register Description
      and Programming Guide.
    properties:
      idt,mode:
        description:
          The output drive mode. Values defined in dt-bindings/clk/versaclock.h
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 6
      idt,voltage-microvolt:
        description: The output drive voltage.
        enum: [ 1800000, 2500000, 3300000 ]
      idt,slew-percent:
        description: The Slew rate control for CMOS single-ended.
        enum: [ 80, 85, 90, 100 ]
    additionalProperties: false

required:
  - compatible
  - reg
  - '#clock-cells'
  - idt,shutdown
  - idt,output-enable-active

allOf:
  - if:
      properties:
        compatible:
          enum:
            - idt,5p49v5933
            - idt,5p49v5935
    then:
      # Devices with builtin crystal + optional external input
      properties:
        clock-names:
          const: clkin
        clocks:
          maxItems: 1
    else:
      # Devices without builtin crystal
      required:
        - clock-names
        - clocks

additionalProperties: false

examples:
  - |
    #include <dt-bindings/clk/versaclock.h>

    /* 25MHz reference crystal */
    ref25: ref25m {
        compatible = "fixed-clock";
        #clock-cells = <0>;
        clock-frequency = <25000000>;
    };

    i2c@0 {
        reg = <0x0 0x100>;
        #address-cells = <1>;
        #size-cells = <0>;

        /* IDT 5P49V5923 I2C clock generator */
        vc5: clock-generator@6a {
            compatible = "idt,5p49v5923";
            reg = <0x6a>;
            #clock-cells = <1>;

            /* Connect XIN input to 25MHz reference */
            clocks = <&ref25m>;
            clock-names = "xin";

            /* Set the SD/OE pin's settings */
            idt,shutdown = <0>;
            idt,output-enable-active = <0>;

            OUT1 {
                idt,mode = <VC5_CMOSD>;
                idt,voltage-microvolt = <1800000>;
                idt,slew-percent = <80>;
            };

            OUT4 {
                idt,mode = <VC5_LVDS>;
            };
        };
    };

...