| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Squash portdrv_{core,pci}.c into portdrv.c to ease maintenance and
make more things static.
- Make portdrv bind to Switch Ports that have AER. Previously, if
these Ports lacked MSI/MSI-X, portdrv failed to bind, which meant
the Ports couldn't be suspended to low-power states. AER on these
Ports doesn't use interrupts, and the AER driver doesn't need to
claim them.
- Assign PCI domain IDs using ida_alloc(), which makes host bridge
add/remove work better.
Resource management:
- To work better with recent BIOSes that use EfiMemoryMappedIO for
PCI host bridge apertures, remove those regions from the E820 map
(E820 entries normally prevent us from allocating BARs). In v5.19,
we added some quirks to disable E820 checking, but that's not very
maintainable. EfiMemoryMappedIO means the OS needs to map the
region for use by EFI runtime services; it shouldn't prevent OS
from using it.
PCIe native device hotplug:
- Build pciehp by default if USB4 is enabled, since Thunderbolt/USB4
PCIe tunneling depends on native PCIe hotplug.
- Enable Command Completed Interrupt only if supported to avoid user
confusion from lspci output that says this is enabled but not
supported.
- Prevent pciehp from binding to Switch Upstream Ports; this happened
because of interaction with acpiphp and caused devices below the
Upstream Port to disappear.
Power management:
- Convert AGP drivers to generic power management. We hope to remove
legacy power management from the PCI core eventually.
Virtualization:
- Fix pci_device_is_present(), which previously always returned
"false" for VFs, causing virtio hangs when unbinding the driver.
Miscellaneous:
- Convert drivers to gpiod API to prepare for dropping some legacy
code.
- Fix DOE fencepost error for the maximum data object length.
Baikal-T1 PCIe controller driver:
- Add driver and DT bindings.
Broadcom STB PCIe controller driver:
- Enable Multi-MSI.
- Delay 100ms after PERST# deassert to allow power and clocks to
stabilize.
- Configure Read Completion Boundary to 64 bytes.
Freescale i.MX6 PCIe controller driver:
- Initialize PHY before deasserting core reset to fix a regression in
v6.0 on boards where the PHY provides the reference.
- Fix imx6sx and imx8mq clock names in DT schema.
Intel VMD host bridge driver:
- Fix Secondary Bus Reset on VMD bridges, which allows reset of NVMe
SSDs in VT-d pass-through scenarios.
- Disable MSI remapping, which gets re-enabled by firmware during
suspend/resume.
MediaTek PCIe Gen3 controller driver:
- Add MT7986 and MT8195 support.
Qualcomm PCIe controller driver:
- Add SC8280XP/SA8540P basic interconnect support.
Rockchip DesignWare PCIe controller driver:
- Base DT schema on common Synopsys schema.
Synopsys DesignWare PCIe core:
- Collect DT items shared between Root Port and Endpoint (PERST GPIO,
PHY info, clocks, resets, link speed, number of lanes, number of
iATU windows, interrupt info, etc) to snps,dw-pcie-common.yaml.
- Add dma-ranges support for Root Ports and Endpoints.
- Consolidate DT resource retrieval for "dbi", "dbi2", "atu", etc. to
reduce code duplication.
- Add generic names for clocks and resets to encourage more
consistent naming across drivers using DesignWare IP.
- Stop advertising PTM Responder role for Endpoints, which aren't
allowed to be responders.
TI J721E PCIe driver:
- Add j721s2 host mode ID to DT schema.
- Add interrupt properties to DT schema.
Toshiba Visconti PCIe controller driver:
- Fix interrupts array max constraints in DT schema"
* tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (95 commits)
x86/PCI: Use pr_info() when possible
x86/PCI: Fix log message typo
x86/PCI: Tidy E820 removal messages
PCI: Skip allocate_resource() if too little space available
efi/x86: Remove EfiMemoryMappedIO from E820 map
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI: xilinx-nwl: Fix coding style violations
PCI: mvebu: Switch to using gpiod API
PCI: pciehp: Enable Command Completed Interrupt only if supported
PCI: aardvark: Switch to using devm_gpiod_get_optional()
dt-bindings: PCI: mediatek-gen3: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: mt7621: Add sentinel to quirks table
PCI: vmd: Fix secondary bus reset for Intel bridges
PCI: endpoint: pci-epf-vntb: Fix sparse ntb->reg build warning
PCI: endpoint: pci-epf-vntb: Fix sparse build warning for epf_db
PCI: endpoint: pci-epf-vntb: Replace hardcoded 4 with sizeof(u32)
PCI: endpoint: pci-epf-vntb: Remove unused epf_db_phy struct member
PCI: endpoint: pci-epf-vntb: Fix call pci_epc_mem_free_addr() in error path
...
|
|
Pull cxl updates from Dan Williams:
"Compute Express Link (CXL) updates for 6.2.
While it may seem backwards, the CXL update this time around includes
some focus on CXL 1.x enabling where the work to date had been with
CXL 2.0 (VH topologies) in mind.
First generation CXL can mostly be supported via BIOS, similar to DDR,
however it became clear there are use cases for OS native CXL error
handling and some CXL 3.0 endpoint features can be deployed on CXL 1.x
hosts (Restricted CXL Host (RCH) topologies). So, this update brings
RCH topologies into the Linux CXL device model.
In support of the ongoing CXL 2.0+ enabling two new core kernel
facilities are added.
One is the ability for the kernel to flag collisions between userspace
access to PCI configuration registers and kernel accesses. This is
brought on by the PCIe Data-Object-Exchange (DOE) facility, a hardware
mailbox over config-cycles.
The other is a cpu_cache_invalidate_memregion() API that maps to
wbinvd_on_all_cpus() on x86. To prevent abuse it is disabled in guest
VMs and architectures that do not support it yet. The CXL paths that
need it, dynamic memory region creation and security commands (erase /
unlock), are disabled when it is not present.
As for the CXL 2.0+ this cycle the subsystem gains support Persistent
Memory Security commands, error handling in response to PCIe AER
notifications, and support for the "XOR" host bridge interleave
algorithm.
Summary:
- Add the cpu_cache_invalidate_memregion() API for cache flushing in
response to physical memory reconfiguration, or memory-side data
invalidation from operations like secure erase or memory-device
unlock.
- Add a facility for the kernel to warn about collisions between
kernel and userspace access to PCI configuration registers
- Add support for Restricted CXL Host (RCH) topologies (formerly CXL
1.1)
- Add handling and reporting of CXL errors reported via the PCIe AER
mechanism
- Add support for CXL Persistent Memory Security commands
- Add support for the "XOR" algorithm for CXL host bridge interleave
- Rework / simplify CXL to NVDIMM interactions
- Miscellaneous cleanups and fixes"
* tag 'cxl-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (71 commits)
cxl/region: Fix memdev reuse check
cxl/pci: Remove endian confusion
cxl/pci: Add some type-safety to the AER trace points
cxl/security: Drop security command ioctl uapi
cxl/mbox: Add variable output size validation for internal commands
cxl/mbox: Enable cxl_mbox_send_cmd() users to validate output size
cxl/security: Fix Get Security State output payload endian handling
cxl: update names for interleave ways conversion macros
cxl: update names for interleave granularity conversion macros
cxl/acpi: Warn about an invalid CHBCR in an existing CHBS entry
tools/testing/cxl: Require cache invalidation bypass
cxl/acpi: Fail decoder add if CXIMS for HBIG is missing
cxl/region: Fix spelling mistake "memergion" -> "memregion"
cxl/regs: Fix sparse warning
cxl/acpi: Set ACPI's CXL _OSC to indicate RCD mode support
tools/testing/cxl: Add an RCH topology
cxl/port: Add RCD endpoint port enumeration
cxl/mem: Move devm_cxl_add_endpoint() from cxl_core to cxl_mem
tools/testing/cxl: Add XOR Math support to cxl_test
cxl/acpi: Support CXL XOR Interleave Math (CXIMS)
...
|
|
Single vector allocation which allocates the next free index in the IMS
space. The free function releases.
All allocated vectors are released also via pci_free_vectors() which is
also releasing MSI/MSI-X vectors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124232326.961711347@linutronix.de
|
|
IMS (Interrupt Message Store) is a new specification which allows
implementation specific storage of MSI messages contrary to the
strict standard specified MSI and MSI-X message stores.
This requires new device specific interrupt domains to handle the
implementation defined storage which can be an array in device memory or
host/guest memory which is shared with hardware queues.
Add a function to create IMS domains for PCI devices. IMS domains are using
the new per device domain mechanism and are configured by the device driver
via a template. IMS domains are created as secondary device domains so they
work side on side with MSI[-X] on the same device.
The IMS domains have a few constraints:
- The index space is managed by the core code.
Device memory based IMS provides a storage array with a fixed size
which obviously requires an index. But there is no association between
index and functionality so the core can randomly allocate an index in
the array.
System memory based IMS does not have the concept of an index as the
storage is somewhere in memory. In that case the index is purely
software based to keep track of the allocations.
- There is no requirement for consecutive index ranges
This is currently a limitation of the MSI core and can be implemented
if there is a justified use case by changing the internal storage from
xarray to maple_tree. For now it's single vector allocation.
- The interrupt chip must provide the following callbacks:
- irq_mask()
- irq_unmask()
- irq_write_msi_msg()
- The interrupt chip must provide the following optional callbacks
when the irq_mask(), irq_unmask() and irq_write_msi_msg() callbacks
cannot operate directly on hardware, e.g. in the case that the
interrupt message store is in queue memory:
- irq_bus_lock()
- irq_bus_unlock()
These callbacks are invoked from preemptible task context and are
allowed to sleep. In this case the mandatory callbacks above just
store the information. The irq_bus_unlock() callback is supposed to
make the change effective before returning.
- Interrupt affinity setting is handled by the underlying parent
interrupt domain and communicated to the IMS domain via
irq_write_msi_msg(). IMS domains cannot have a irq_set_affinity()
callback. That's a reasonable restriction similar to the PCI/MSI
device domain implementations.
The domain is automatically destroyed when the PCI device is removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124232326.904316841@linutronix.de
|
|
MSI-X vectors can be allocated after the initial MSI-X enablement, but this
needs explicit support of the underlying interrupt domains.
Provide a function to query the ability and functions to allocate/free
individual vectors post-enable.
The allocation can either request a specific index in the MSI-X table or
with the index argument MSI_ANY_INDEX it allocates the next free vector.
The return value is a struct msi_map which on success contains both index
and the Linux interrupt number. In case of failure index is negative and
the Linux interrupt number is 0.
The allocation function is for a single MSI-X index at a time as that's
sufficient for the most urgent use case VFIO to get rid of the 'disable
MSI-X, reallocate, enable-MSI-X' cycle which is prone to lost interrupts
and redirections to the legacy and obviously unhandled INTx.
As single index allocation is also sufficient for the use cases Jason
Gunthorpe pointed out: Allocation of a MSI-X or IMS vector for a network
queue. See Link below.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/all/20211126232735.547996838@linutronix.de
Link: https://lore.kernel.org/r/20221124232326.731233614@linutronix.de
|
|
Pick up CXL AER handling and correctable error extensions. Resolve
conflicts with cxl_pmem_wq reworks and RCH support.
|
|
Some new devices such as CXL devices may want to record additional error
information on a corrected error. Add a callback to allow the PCI device
driver to do additional logging such as providing additional stats for user
space RAS monitoring.
For CXL device, this is actually a need due to CXL needing to write to the
CXL RAS capability structure correctable error status register in order to
clear the unmasked correctable errors. See CXL spec rev3.0 8.2.4.16.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166984619233.2804404.3966368388544312674.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Make pci_alloc_irq_vectors() a real function instead of wrapper and add
proper kernel doc to it.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.870888193@linutronix.de
|
|
PCI config space access from user space has traditionally been
unrestricted with writes being an understood risk for device operation.
Unfortunately, device breakage or odd behavior from config writes lacks
indicators that can leave driver writers confused when evaluating
failures. This is especially true with the new PCIe Data Object
Exchange (DOE) mailbox protocol where backdoor shenanigans from user
space through things such as vendor defined protocols may affect device
operation without complete breakage.
A prior proposal restricted read and writes completely.[1] Greg and
Bjorn pointed out that proposal is flawed for a couple of reasons.
First, lspci should always be allowed and should not interfere with any
device operation. Second, setpci is a valuable tool that is sometimes
necessary and it should not be completely restricted.[2] Finally
methods exist for full lock of device access if required.
Even though access should not be restricted it would be nice for driver
writers to be able to flag critical parts of the config space such that
interference from user space can be detected.
Introduce pci_request_config_region_exclusive() to mark exclusive config
regions. Such regions trigger a warning and kernel taint if accessed
via user space.
Create pci_warn_once() to restrict the user from spamming the log.
[1] https://lore.kernel.org/all/161663543465.1867664.5674061943008380442.stgit@dwillia2-desk3.amr.corp.intel.com/
[2] https://lore.kernel.org/all/YF8NGeGv9vYcMfTV@kroah.com/
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20220926215711.2893286-2-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Replace assignment of PCI domain IDs from atomic_inc_return() to
ida_alloc().
Use two IDAs, one for static domain allocations (those which are defined in
device tree) and second for dynamic allocations (all other).
During removal of root bus / host bridge, also release the domain ID. The
released ID can be reused again, for example when dynamically loading and
unloading native PCI host bridge drivers.
This change also allows to mix static device tree assignment and dynamic by
kernel as all static allocations are reserved in dynamic pool.
[bhelgaas: set "err" if "bus->domain_nr < 0"]
Link: https://lore.kernel.org/r/20220714184130.5436-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better.
- Revert to a BAR assignment inherited from firmware only when the
address is actually reachable via any upstream bridges, which fixes
some cases where firmware doesn't configure all devices.
- Add a sysfs interface to resize BARs so this can be done before
assigning devices to a VM through VFIO.
Power management:
- Disable Precision Time Management for all devices on suspend to
enable lower-power PM state. We previously did this just for Root
Ports, which isn't enough because downstream devices can still
generate PTM messages, which cause errors if it's disabled in the
Root Port.
- Save and restore the ASPM L1 PM Substates configuration for
suspend/ resume. Previously this configuration was lost, so L1.x
states likely stopped working after resume.
- Check whether the L1 PM Substates Capability exists. If it didn't
exist, we previously read junk and tried to configure L1 Substates
based on that.
- Fix the LTR_L1.2_THRESHOLD computation, which previously set a
threshold for entering L1.2 that was too low in some cases.
- Reduce the delay after transitions to or from D3cold by using
usleep_range() rather than msleep(), which often slept for ~19ms
instead of the 10ms normally required. The spec says 10ms is
enough, but it's possible we could trip over devices that need a
little more.
Error handling:
- Work around a BIOS bug that caused Intel Root Ports to advertise a
Root Port Programmed I/O (RP PIO) log size of zero, which caused
annoying warnings and prevented the kernel from dumping log
registers for DPC errors.
Qualcomm PCIe controller driver:
- Add support for SC8280XP and SA8540P host controllers and SM8450
endpoint controller.
- Disable Master AXI clock on endpoint controllers to save power when
link is idle or in L1.x.
- Expose link state transition counts via debugfs to help debug
issues with low-power states.
- Add auto-loading module support.
Synopsys DesignWare PCIe controller driver:
- Remove a dependency on ZONE_DMA32 by allocating the MSI target page
differently. There's more work to do related to eDMA controllers,
so it's not completely settled"
* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: Expose PCIe Resizable BAR support via sysfs
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
...
|
|
CONFIG_CFI_CLANG doesn't use a jump table anymore and therefore,
won't change function references to point elsewhere. Remove the
__cficanonical attribute and all uses of it.
Note that the Clang definition of the attribute was removed earlier,
just clean up the no-op definition and users.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220908215504.3686827-16-samitolvanen@google.com
|
|
We disable PTM during suspend because that allows some Root Ports to enter
lower-power PM states, which means we also need to disable PTM for all
downstream devices. Add pci_suspend_ptm() and pci_resume_ptm() for this
purpose.
pci_enable_ptm() and pci_disable_ptm() are for drivers to use to enable or
disable PTM. They use dev->ptm_enabled to keep track of whether PTM should
be enabled.
pci_suspend_ptm() and pci_resume_ptm() are PCI core-internal functions to
temporarily disable PTM during suspend and (depending on dev->ptm_enabled)
re-enable PTM during resume.
Enable/disable/suspend/resume all use internal __pci_enable_ptm() and
__pci_disable_ptm() functions that only update the PTM Control register.
Outline:
pci_enable_ptm(struct pci_dev *dev)
{
__pci_enable_ptm(dev);
dev->ptm_enabled = 1;
pci_ptm_info(dev);
}
pci_disable_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled) {
__pci_disable_ptm(dev);
dev->ptm_enabled = 0;
}
}
pci_suspend_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_disable_ptm(dev);
}
pci_resume_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_enable_ptm(dev);
}
Nothing currently calls pci_resume_ptm(); the suspend path saves the PTM
state before disabling PTM, so the PTM state restore in the resume path
implicitly re-enables it. A future change will use pci_resume_ptm() to fix
some problems with this approach.
Link: https://lore.kernel.org/r/20220909202505.314195-5-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Cache the PTM Capability offset instead of searching for it every time we
enable/disable PTM or save/restore PTM state. No functional change
intended.
Link: https://lore.kernel.org/r/20220909202505.314195-2-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The ARCH_GENERIC_PCI_MMAP_RESOURCE symbol came up in a recent discussion,
and I noticed that this was left behind by an unfinished cleanup from 2017.
The only architecture that still relies on providing its own
pci_mmap_page_range() helper instead of using the generic
pci_mmap_resource_range() is sparc. Presumably the reasons for this have
not changed, but at least this can be simplified by converting sparc to use
the same interface as the others.
The only difference between the two is the device-specific offset that gets
added to or subtracted from vma->vm_pgoff.
Change the only caller of pci_mmap_page_range() in common code to subtract
this offset and call the modern interface, while adding it back in the
sparc implementation to preserve the existing behavior.
This removes the complexities of the dual interfaces from the common code,
and keeps it all specific to the sparc architecture code. According to
David Miller, the sparc code lets user space poke into the VGA I/O port
registers by mmapping the I/O space of the parent bridge device, which is
something that the generic pci_mmap_resource_range() code apparently does
not.
Link: https://lore.kernel.org/lkml/1519887203.622.3.camel@infradead.org/t/
Link: https://lore.kernel.org/lkml/20220714214657.2402250-3-shorne@gmail.com/
Link: https://lore.kernel.org/r/20220715153617.3393420-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stafford Horne <shorne@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel VT-d driver updates:
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates:
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU legacy
binding
- Minor cleanups
- Fix a BUG_ON in the vfio_iommu_group_notifier:
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group is
either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Make forcing of cache-coherent DMA more coherent between IOMMU
drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu/amd: Increase timeout waiting for GA log enablement
iommu/s390: Tolerate repeat attach_dev calls
iommu/vt-d: Remove hard coding PGSNP bit in PASID entries
iommu/vt-d: Remove domain_update_iommu_snooping()
iommu/vt-d: Check domain force_snooping against attached devices
iommu/vt-d: Block force-snoop domain attaching if no SC support
iommu/vt-d: Size Page Request Queue to avoid overflow condition
iommu/vt-d: Fold dmar_insert_one_dev_info() into its caller
iommu/vt-d: Change return type of dmar_insert_one_dev_info()
iommu/vt-d: Remove unneeded validity check on dev
iommu/dma: Explicitly sort PCI DMA windows
iommu/dma: Fix iova map result check bug
iommu/mediatek: Fix NULL pointer dereference when printing dev_name
iommu: iommu_group_claim_dma_owner() must always assign a domain
iommu/arm-smmu: Force identity domains for legacy binding
iommu/arm-smmu: Support Tegra234 SMMU
dt-bindings: arm-smmu: Add compatible for Tegra234 SOC
dt-bindings: arm-smmu: Document nvidia,memory-controller property
iommu/arm-smmu-qcom: Add SC8280XP support
dt-bindings: arm-smmu: Add compatible for Qualcomm SC8280XP
...
|
|
The runtime_d3cold flag is not needed any more, so drop it.
Link: https://lore.kernel.org/r/8077784.T7Z3S40VBb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The devices on platform/amba/fsl-mc/PCI buses could be bound to drivers
with the device DMA managed by kernel drivers or user-space applications.
Unfortunately, multiple devices may be placed in the same IOMMU group
because they cannot be isolated from each other. The DMA on these devices
must either be entirely under kernel control or userspace control, never
a mixture. Otherwise the driver integrity is not guaranteed because they
could access each other through the peer-to-peer accesses which by-pass
the IOMMU protection.
This checks and sets the default DMA mode during driver binding, and
cleanups during driver unbinding. In the default mode, the device DMA is
managed by the device driver which handles DMA operations through the
kernel DMA APIs (see Documentation/core-api/dma-api.rst).
For cases where the devices are assigned for userspace control through the
userspace driver framework(i.e. VFIO), the drivers(for example, vfio_pci/
vfio_platfrom etc.) may set a new flag (driver_managed_dma) to skip this
default setting in the assumption that the drivers know what they are
doing with the device DMA.
Calling iommu_device_use_default_domain() before {of,acpi}_dma_configure
is currently a problem. As things stand, the IOMMU driver ignored the
initial iommu_probe_device() call when the device was added, since at
that point it had no fwspec yet. In this situation,
{of,acpi}_iommu_configure() are retriggering iommu_probe_device() after
the IOMMU driver has seen the firmware data via .of_xlate to learn that
it actually responsible for the given device. As the result, before
that gets fixed, iommu_use_default_domain() goes at the end, and calls
arch_teardown_dma_ops() if it fails.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20220418005000.897664-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Use a helper to set driver_override to the reduce amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that all usages of the functions defined in "pci-dma-compat.h" have
been removed, it is time to remove this file as well.
In order not to break builds, move the "#include <linux/dma-mapping.h>"
that was in "pci-dma-compat.h" into "include/linux/pci.h"
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
|
|
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
|
|
There are some cases where a SR-IOV VF driver will need to reach into and
interact with the PF driver. This requires accessing the drvdata of the PF.
Provide a function pci_iov_get_pf_drvdata() to return this PF drvdata in a
safe way. Normally accessing a drvdata of a foreign struct device would be
done using the device_lock() to protect against device driver
probe()/remove() races.
However, due to the design of pci_enable_sriov() this will result in a
ABBA deadlock on the device_lock as the PF's device_lock is held during PF
sriov_configure() while calling pci_enable_sriov() which in turn holds the
VF's device_lock while calling VF probe(), and similarly for remove.
This means the VF driver can never obtain the PF's device_lock.
Instead use the implicit locking created by pci_enable/disable_sriov(). A
VF driver can access its PF drvdata only while its own driver is attached,
and the PF driver can control access to its own drvdata based on when it
calls pci_enable/disable_sriov().
To use this API the PF driver will setup the PF drvdata in the probe()
function. pci_enable_sriov() is only called from sriov_configure() which
cannot happen until probe() completes, ensuring no VF races with drvdata
setup.
For removal, the PF driver must call pci_disable_sriov() in its remove
function before destroying any of the drvdata. This ensures that all VF
drivers are unbound before returning, fencing concurrent access to the
drvdata.
The introduction of a new function to do this access makes clear the
special locking scheme and the documents the requirements on the PF/VF
drivers using this.
Link: https://lore.kernel.org/all/20220224142024.147653-5-yishaih@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The PCI core uses the VF index internally, often called the vf_id,
during the setup of the VF, eg pci_iov_add_virtfn().
This index is needed for device drivers that implement live migration
for their internal operations that configure/control their VFs.
Specifically, mlx5_vfio_pci driver that is introduced in coming patches
from this series needs it and not the bus/device/function which is
exposed today.
Add pci_iov_vf_id() which computes the vf_id by reversing the math that
was used to create the bus/device/function.
Link: https://lore.kernel.org/all/20220224142024.147653-2-yishaih@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
|
|
- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking
for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead
of in host controller drivers, when transactions fail on PCI (Naveen
Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads
(Naveen Naidu)
* pci/errors:
PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: rockchip-host: Drop error data fabrication when config read fails
PCI: rcar-host: Drop error data fabrication when config read fails
PCI: altera: Drop error data fabrication when config read fails
PCI: mvebu: Drop error data fabrication when config read fails
PCI: aardvark: Drop error data fabrication when config read fails
PCI: kirin: Drop error data fabrication when config read fails
PCI: histb: Drop error data fabrication when config read fails
PCI: exynos: Drop error data fabrication when config read fails
PCI: mediatek: Drop error data fabrication when config read fails
PCI: iproc: Drop error data fabrication when config read fails
PCI: thunder: Drop error data fabrication when config read fails
PCI: Drop error data fabrication when config read fails
PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices
PCI: Set error response data when config read fails
PCI: Add PCI_ERROR_RESPONSE and related definitions
|
|
- Always write Intel I210 ROM BAR on update to work around device defect
(Bjorn Helgaas)
* pci/resource:
PCI: Work around Intel I210 ROM BAR overlap defect
|
|
Per PCIe r5, sec 7.5.1.2.4, a device must not claim accesses to its
Expansion ROM unless both the Memory Space Enable and the Expansion ROM
Enable bit are set. But apparently some Intel I210 NICs don't work
correctly if the ROM BAR overlaps another BAR, even if the Expansion ROM is
disabled.
Michael reported that on a Kontron SMARC-sAL28 ARM64 system with U-Boot
v2021.01-rc3, the ROM BAR overlaps BAR 3, and networking doesn't work at
all:
BAR 0: 0x40000000 (32-bit, non-prefetchable) [size=1M]
BAR 3: 0x40200000 (32-bit, non-prefetchable) [size=16K]
ROM: 0x40200000 (disabled) [size=1M]
NETDEV WATCHDOG: enP2p1s0 (igb): transmit queue 0 timed out
Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
igb 0002:01:00.0 enP2p1s0: Reset adapter
Previously, pci_std_update_resource() wrote the assigned ROM address to the
BAR only when the ROM was enabled. This meant that the I210 ROM BAR could
be left with an address assigned by firmware, which might overlap with
other BARs.
Quirk these I210 devices so pci_std_update_resource() always writes the
assigned address to the ROM BAR, whether or not the ROM is enabled.
Link: https://lore.kernel.org/r/20211223163754.GA1267351@bhelgaas
Link: https://lore.kernel.org/r/20201230185317.30915-1-michael@walle.cc
Link: https://bugzilla.kernel.org/show_bug.cgi?id=211105
Reported-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Change the pci_dev_present() stub which is used when CONFIG_PCI is not set
from a #define to a static inline stub.
Thix should fix clang -Werror builds failing due to errors like this:
drivers/platform/x86/thinkpad_acpi.c:4475:35:
error: unused variable 'fwbug_cards_ids' [-Werror,-Wunused-const-variable]
Where fwbug_cards_ids is an array of pci_device_id passed to
pci_dev_present() during a quirk check.
Link: https://lore.kernel.org/r/20211217141515.379586-1-hdegoede@redhat.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: platform-driver-x86@vger.kernel.org
|
|
Set the domain info flag which makes the core code handle sysfs groups and
put an explicit invocation into the legacy code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211210221814.048612053@linutronix.de
|
|
The MSI core will introduce runtime allocation of MSI related data. This
data will be devres managed and has to be set up before enabling
PCI/MSI[-X]. This would introduce an ordering issue vs. pcim_release().
The setup order is:
pcim_enable_device()
devres_alloc(pcim_release...);
...
pci_irq_alloc()
msi_setup_device_data()
devres_alloc(msi_device_data_release, ...)
and once the device is released these release functions are invoked in the
opposite order:
msi_device_data_release()
...
pcim_release()
pci_disable_msi[x]()
which is obviously wrong, because pci_disable_msi[x]() requires the MSI
data to be available to tear down the MSI[-X] interrupts.
Remove the MSI[-X] teardown from pcim_release() and add an explicit action
to be installed on the attempt of enabling PCI/MSI[-X].
This allows the MSI core data allocation to be ordered correctly in a
subsequent step.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/87tuf9rdoj.ffs@tglx
|
|
It's only required for PCI/MSI. So no point in having it in every struct
device.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210224.925241961@linutronix.de
|
|
Unmapping the MSI-X base mapping in the loops which allocate/free MSI
descriptors is daft and in the way of allowing runtime expansion of MSI-X
descriptors.
Store the mapping in struct pci_dev and free it after freeing the MSI-X
descriptors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210224.871651518@linutronix.de
|
|
A config or MMIO read from a PCI device that doesn't exist or doesn't
respond causes a PCI error. There's no real data to return to satisfy the
CPU read, so most hardware fabricates ~0 data.
Add a PCI_ERROR_RESPONSE definition for that and use it where appropriate
to make these checks consistent and easier to find.
Also add helper definitions PCI_SET_ERROR_RESPONSE() and
PCI_POSSIBLE_ERROR() to make the code more readable.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/55563bf4dfc5d3fdc96695373c659d099bf175b1.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem
Core code:
- A regression fix for the Open Firmware interrupt mapping code where
a interrupt controller property in a node caused a map property in
the same node to be ignored.
Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which
silently ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse
the chip comes out of reset with all MSI entries masked, which due
to the missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code"
* tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
of/irq: Don't ignore interrupt-controller when interrupt-map failed
irqchip/sifive-plic: Fixup EOI failed when masked
irqchip/csky-mpintc: Fixup mask/unmask implementation
PCI/MSI: Destroy sysfs before freeing entries
PCI: Add MSI masking quirk for Nvidia ION AHCI
PCI/MSI: Deal with devices lying about their MSI mask capability
PCI/MSI: Move non-mask check back into low level accessors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api
cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in the
schib in cio code.
* tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: check the subchannel validity for dev_busid
s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove
s390/tape: fix timer initialization in tape_std_assign()
s390/pci: implement minimal PCI error recovery
PCI: Export pci_dev_lock()
s390/pci: implement reset_slot for hotplug slot
s390/pci: refresh function handle in iomap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert conversion to struct device.driver instead of struct
pci_dev.driver.
The device.driver is set earlier, and using it caused the PCI core to
call driver PM entry points before .probe() and after .remove(), when
the driver isn't prepared.
This caused NULL pointer dereferences in i2c_designware_pci and
probably other driver issues"
* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
Revert "PCI: Remove struct pci_dev->driver"
|
|
This reverts commit b5f9c644eb1baafcd349ad134e2110773f8d0a38.
Revert b5f9c644eb1b ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").
2a4d9408c9e8 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.
Fixes: 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl updates from Dan Williams:
"More preparation and plumbing work in the CXL subsystem.
From an end user perspective the highlight here is lighting up the CXL
Persistent Memory related commands (label read / write) with the
generic ioctl() front-end in LIBNVDIMM.
Otherwise, the ability to instantiate new persistent and volatile
memory regions is still on track for v5.17.
Summary:
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up
open coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs.
'cxl_test' is a module built from tools/testing/cxl/ that mocks up
a CXL topology to augment the nascent support for emulation of CXL
devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver
and core-infrastructure buckets. For example, mailbox handling is
now a generic core capability consumed by the PCI and cxl_test
drivers"
* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
ocxl: Use pci core's DVSEC functionality
cxl/pci: Use pci core's DVSEC functionality
PCI: Add pci_find_dvsec_capability to find designated VSEC
cxl/pci: Split cxl_pci_setup_regs()
cxl/pci: Add @base to cxl_register_map
cxl/pci: Make more use of cxl_register_map
cxl/pci: Remove pci request/release regions
cxl/pci: Fix NULL vs ERR_PTR confusion
cxl/pci: Remove dev_dbg for unknown register blocks
cxl/pci: Convert register block identifiers to an enum
cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
cxl/pci: Disambiguate cxl_pci further from cxl_mem
Documentation/cxl: Add bus internal docs
cxl/core: Split decoder setup into alloc + add
tools/testing/cxl: Introduce a mock memory device + driver
cxl/mbox: Move command definitions to common location
cxl/bus: Populate the target list at decoder create
tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
cxl/pmem: Add support for multiple nvdimm-bridge objects
cxl/pmem: Translate NVDIMM label commands to CXL label commands
...
|
|
Commit e3a9b1212b9d ("PCI: Export pci_dev_trylock() and pci_dev_unlock()")
already exported pci_dev_trylock()/pci_dev_unlock() however in some
circumstances such as during error recovery it makes sense to block
waiting to get full access to the device so also export pci_dev_lock().
Link: https://lore.kernel.org/all/20210928181014.GA713179@bhelgaas/
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
|
|
- Add pci_read_vpd_any(), pci_write_vpd_any() to access VPD at arbitrary
offsets (Heiner Kallweit)
- Use VPD API to replace custom code in cxgb3 driver (Heiner Kallweit)
* pci/vpd:
cxgb3: Remove seeprom_write and use VPD API
cxgb3: Use VPD API in t3_seeprom_wp()
cxgb3: Remove t3_seeprom_read and use VPD API
PCI/VPD: Use pci_read_vpd_any() in pci_vpd_size()
PCI/VPD: Add pci_read/write_vpd_any()
|
|
- Drop the struct pci_dev.driver pointer, which is redundant with the
struct device.driver pointer (Uwe Kleine-König)
* pci/driver:
PCI: Remove struct pci_dev->driver
PCI: Use to_pci_driver() instead of pci_dev->driver
x86/pci/probe_roms: Use to_pci_driver() instead of pci_dev->driver
perf/x86/intel/uncore: Use to_pci_driver() instead of pci_dev->driver
powerpc/eeh: Use to_pci_driver() instead of pci_dev->driver
usb: xhci: Use to_pci_driver() instead of pci_dev->driver
cxl: Use to_pci_driver() instead of pci_dev->driver
cxl: Factor out common dev->driver expressions
xen/pcifront: Use to_pci_driver() instead of pci_dev->driver
xen/pcifront: Drop pcifront_common_process() tests of pcidev, pdrv
nfp: use dev_driver_string() instead of pci_dev->driver->name
mlxsw: pci: Use dev_driver_string() instead of pci_dev->driver->name
net: marvell: prestera: use dev_driver_string() instead of pci_dev->driver->name
net: hns3: use dev_driver_string() instead of pci_dev->driver->name
crypto: hisilicon - use dev_driver_string() instead of pci_dev->driver->name
powerpc/eeh: Use dev_driver_string() instead of struct pci_dev->driver->name
ssb: Use dev_driver_string() instead of pci_dev->driver->name
bcma: simplify reference to driver name
crypto: qat - simplify adf_enable_aer()
scsi: message: fusion: Remove unused mpt_pci driver .probe() 'id' parameter
PCI/ERR: Factor out common dev->driver expressions
PCI: Drop pci_device_probe() test of !pci_dev->driver
PCI: Drop pci_device_remove() test of pci_dev->driver
PCI: Return NULL for to_pci_driver(NULL)
|
|
Add pci_find_dvsec_capability to locate a Designated Vendor-Specific
Extended Capability with the specified Vendor ID and Capability ID.
The Designated Vendor-Specific Extended Capability (DVSEC) allows one or
more "vendor" specific capabilities that are not tied to the Vendor ID
of the PCI component. Where the DVSEC Vendor may be a standards body
like CXL.
Cc: David E. Box <david.e.box@linux.intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-pci@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163379787943.692348.6814373487017444007.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The pci_pool users have been converted to dma_pool. Remove the unused
pci_pool wrappers.
Link: https://lore.kernel.org/r/20211018124110.214-1-caihuoqing@baidu.com
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There are no remaining uses of the struct pci_dev->driver pointer, so
remove it.
Link: https://lore.kernel.org/r/20211004125935.2300113-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
to_pci_driver() takes a pointer to a struct device_driver and uses
container_of() to find the struct pci_driver that contains it.
If given a NULL pointer to a struct device_driver, return a NULL pci_driver
pointer instead of applying container_of() to NULL.
This simplifies callers that would otherwise have to check for a NULL
pointer first.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
In certain cases we need a variant of pci_read_vpd()/pci_write_vpd() that
does not check against dev->vpd.len. Such cases are:
- Reading VPD if dev->vpd.len isn't set yet (in pci_vpd_size())
- Devices that map non-VPD information to arbitrary places in VPD address
space (example: Chelsio T3 EEPROM write-protect flag)
Therefore add pci_read_vpd_any() and pci_write_vpd_any() that check against
PCI_VPD_MAX_SIZE only.
Link: https://lore.kernel.org/r/93ecce28-a158-f02a-d134-8afcaced8efe@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
|
