Age | Commit message (Collapse) | Author | Files | Lines |
|
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing pci_disable_device() in error path of probe() and remove() path.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The cited commit at rx sa update operation passes the sci object
attribute, in the wrong endianness and not as expected by the HW
effectively create malformed hw sa context in case of update rx sa
consequently, HW produces unexpected MACsec packets which uses this
sa.
Fix by passing sci to create macsec object with the correct endianness,
while at it add __force u64 to prevent sparse check error of type
"sparse: error: incorrect type in assignment".
Fixes: aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cited commit produces a sparse check error of type
"sparse: error: restricted __be64 degrades to integer". The
offending line wrongly did a bitwise operation between two different
storage types one of 64 bit when the other smaller side is 16 bit
which caused the above sparse error, furthermore bitwise operation
usage here is wrong in the first place as the constant MACSEC_PORT_ES
is not a bitwise field.
Fix by using the right mask to get the lower 16 bit if the sci number,
and use comparison operator '==' instead of bitwise '&' operator.
Fixes: 3b20949cb21b ("net/mlx5e: Add MACsec RX steering rules")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-15-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cited commit adds the support for update/delete MACsec Rx SA,
naturally, these operations need to check if the SA in question exists
to update/delete the SA and return error code otherwise, however they
do just the opposite i.e. return with error if the SA exists
Fix by change the check to return error in case the SA in question does
not exist, adjust error message and code accordingly.
Fixes: aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cited commit at update rx sa operation passes object attributes
to MACsec object create function without initializing/setting all
attributes fields leaving some of them with garbage values, therefore
violating the implicit assumption at create object function, which
assumes that all input object attributes fields are set.
Fix by initializing the object attributes struct to zero, thus leaving
unset fields with the legal zero value.
Fixes: aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes: 5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes: 6181e5cb752e ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On multi table split the driver creates a new attr instance with
data being copied from prev attr instance zeroing action flags.
Also need to reset dests properties to avoid incorrect dests per attr.
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reject TC rules that forward from internal port to internal port
as it is not supported.
This include rules that are explicitly have internal port as
the filter device as well as rules that apply on tunnel interfaces
as the route device for the tunnel interface can be an internal
port.
Fixes: 27484f7170ed ("net/mlx5e: Offload tc rules that redirect to ovs internal port")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242
RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110
RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc
RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3
R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005
R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 49502:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x11d/0x1b0
kfree+0x1ba/0x520
mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlx5 SQs must select the timestamp format explicitly according to the
active clock mode, select the current active timestamp mode so ASO SQ create
will succeed.
This fixes the following error prints when trying to create ipsec ASO SQ
while the timestamp format is real time mode.
mlx5_cmd_out_err:778:(pid 34874): CREATE_SQ(0x904) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xd61c0b), err(-22)
mlx5_aso_create_sq:285:(pid 34874): Failed to open aso wq sq, err=-22
mlx5e_ipsec_init:436:(pid 34874): IPSec initialization failed, -22
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: 1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes: cc2295cd54e4 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers")
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88f5 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390bb ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes: ab1d0cc004d7 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nsim_dev_resources_register() failed
If some items in nsim_dev_resources_register() fail, memory leak will
occur. The following is the memory leak information.
unreferenced object 0xffff888074c02600 (size 128):
comm "echo", pid 8159, jiffies 4294945184 (age 493.530s)
hex dump (first 32 bytes):
40 47 ea 89 ff ff ff ff 01 00 00 00 00 00 00 00 @G..............
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
backtrace:
[<0000000011a31c98>] kmalloc_trace+0x22/0x60
[<0000000027384c69>] devl_resource_register+0x144/0x4e0
[<00000000a16db248>] nsim_drv_probe+0x37a/0x1260
[<000000007d1f448c>] really_probe+0x20b/0xb10
[<00000000c416848a>] __driver_probe_device+0x1b3/0x4a0
[<00000000077e0351>] driver_probe_device+0x49/0x140
[<0000000054f2465a>] __device_attach_driver+0x18c/0x2a0
[<000000008538f359>] bus_for_each_drv+0x151/0x1d0
[<0000000038e09747>] __device_attach+0x1c9/0x4e0
[<00000000dd86e533>] bus_probe_device+0x1d5/0x280
[<00000000839bea35>] device_add+0xae0/0x1cb0
[<000000009c2abf46>] new_device_store+0x3b6/0x5f0
[<00000000fb823d7f>] bus_attr_store+0x72/0xa0
[<000000007acc4295>] sysfs_kf_write+0x106/0x160
[<000000005f50cb4d>] kernfs_fop_write_iter+0x3a8/0x5a0
[<0000000075eb41bf>] vfs_write+0x8f0/0xc80
Fixes: 37923ed6b8ce ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If device_register() failed in nsim_bus_dev_new(), the value of reference
in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be
released.
unreferenced object 0xffff88810352c480 (size 16):
comm "echo", pid 5691, jiffies 4294945921 (age 133.270s)
hex dump (first 16 bytes):
6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1......
backtrace:
[<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0
[<0000000094ca4fc8>] kvasprintf+0xc3/0x160
[<00000000aad09bcc>] kvasprintf_const+0x55/0x180
[<000000009bac868d>] kobject_set_name_vargs+0x56/0x150
[<000000007c1a5d70>] dev_set_name+0xbb/0xf0
[<00000000ad0d126b>] device_add+0x1f8/0x1cb0
[<00000000c222ae24>] new_device_store+0x3b6/0x5e0
[<0000000043593421>] bus_attr_store+0x72/0xa0
[<00000000cbb1833a>] sysfs_kf_write+0x106/0x160
[<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0
[<00000000770b66e2>] vfs_write+0x8f0/0xc80
[<0000000078bb39be>] ksys_write+0x106/0x210
[<00000000005e55a4>] do_syscall_64+0x35/0x80
[<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 40e4fe4ce115 ("netdevsim: move device registration and related code to bus.c")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221026015405.128795-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-27
Anssi Hannula fixes the use of the completions in the kvaser_usb
driver.
Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm
that can be triggered by high CAN bus load and channel specific IRQ
handlers are fixed.
Yang Yingliang fixes the j1939 transport protocol by moving a
kfree_skb() out of a spin_lock_irqsave protected section.
* tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
can: kvaser_usb: Fix possible completions during init_completion
====================
Link: https://lore.kernel.org/r/20221027114356.1939821-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.1
- make the multipath dma alignment to match the non-multipath one
(Keith Busch)
- fix a bogus use of sg_init_marker() (Nam Cao)
- fix circulr locking in nvme-tcp (Sagi Grimberg)"
* tag 'nvme-6.1-2022-10-27' of git://git.infradead.org/nvme:
nvme-multipath: set queue dma alignment to 3
nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
nvme-tcp: replace sg_init_marker() with sg_init_table()
|
|
If device_register() returns error in rbd_sysfs_init(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop
the reference count that was set in device_initialize() when it fails,
so the name can be freed in kobject_cleanup().
Fault injection test can trigger this problem:
unreferenced object 0xffff88810173aa78 (size 8):
comm "modprobe", pid 247, jiffies 4294714278 (age 31.789s)
hex dump (first 8 bytes):
72 62 64 00 81 88 ff ff rbd.....
backtrace:
[<00000000f58fae56>] __kmalloc_node_track_caller+0x44/0x1b0
[<00000000bdd44fe7>] kstrdup+0x3a/0x70
[<00000000f7844d0b>] kstrdup_const+0x63/0x80
[<000000001b0a0eeb>] kvasprintf_const+0x10b/0x190
[<00000000a47bd894>] kobject_set_name_vargs+0x56/0x150
[<00000000d5edbf18>] dev_set_name+0xab/0xe0
[<00000000f5153e80>] device_add+0x106/0x1f20
Fixes: dfc5606dc513 ("rbd: replace the rbd sysfs interface")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221027091918.2294132-1-yangyingliang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes: 1acf2318dd13 ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
FIFO receive
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Return on error directly from the BAR-iterating loop instead of
break+return.
This is actually a cosmetic fix, since it would be highly unusual to
have this called for a PCI device without any memory BARs.
Fixes: 9d69ef183815 ("fbdev/core: Remove remove_conflicting_pci_framebuffers()")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/e75323732bedc46d613d72ecb40f97e3bc75eea8.1666829073.git.mirq-linux@rere.qmqm.pl
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.1-2022-10-26-1:
amdgpu:
- Stable pstate fix
- SMU 13.x updates
- SR-IOV fixes
- PCI AER fix
- GC 11.x fixes
- Display fixes
- Expose IMU firmware version for debugging
- Plane modifier fix
- S0i3 fix
amdkfd:
- Fix possible memory leak
- Fix GC 10.x cache info reporting
UAPI:
- Expose IMU firmware version via existing INFO firmware query
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221027024101.6881-1-alexander.deucher@amd.com
|
|
The parisc serial port driver needs this symbol when it's compiled
as module.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
Cc: <stable@vger.kernel.org>
|
|
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
msm-fixes for v6.1
- Fix shrinker deadlock
- Fix crash during suspend after unbind
- Fix IRQ lifetime issues
- Fix potential memory corruption with too many bridges
- Fix memory corruption on GPU state capture
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGveadezhqm=Sra7Jq4A3tFAp_eBmKKOoHLnapN03pVoLw@mail.gmail.com
|
|
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-25
The 1st patch adds a missing cleanup call in the error path of the
probe function in mpc5xxx glue code for the mscan driver.
The 2nd patch adds a missing cleanup call in the error path of the
probe function of the mcp251x driver.
* tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
====================
Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
|
|
In the S2idle suspend/resume phase the gfxoff is keeping functional so
some IP blocks will be likely to reinitialize at gfxoff entry and that
will result in failing to program GC registers.Therefore, let disallow
gfxoff until AMDGPU IPs reinitialized completely.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15.x
|
|
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vfio-ap crypto driver fails to allocate memory for an array of
pointers used to pass supported mdev types to mdev_register_parent().
Since we only support a single mdev type, the fix is to allocate a
single entry in the ap_matrix_dev->mdev_types array.
Link: https://lore.kernel.org/r/20221021145905.15100-1-jjherne@linux.ibm.com
Fixes: da44c340c4fe ("vfio/mdev: simplify mdev_type handling")
Cc: stable@vger.kernel.org
Cc: Tony Krowiak <akrowiak@linux.ibm.com>
Reported-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The channel-subsystem-driver scans for newly available devices whenever
device-IDs are removed from the cio_ignore list using a command such as:
echo free >/proc/cio_ignore
Since an I/O device scan might interfer with running I/Os, commit
172da89ed0ea ("s390/cio: avoid excessive path-verification requests")
introduced an optimization to exclude online devices from the scan.
The newly added check for online devices incorrectly assumes that
an I/O-subchannel's drvdata points to a struct io_subchannel_private.
For devices that are bound to a non-default I/O subchannel driver, such
as the vfio_ccw driver, this results in an out-of-bounds read access
during each scan.
Fix this by changing the scan logic to rely on a driver-independent
online indication. For this we can use struct subchannel->config.ena,
which is the driver's requested subchannel-enabled state. Since I/Os
can only be started on enabled subchannels, this matches the intent
of the original optimization of not scanning devices where I/O might
be running.
Fixes: 172da89ed0ea ("s390/cio: avoid excessive path-verification requests")
Fixes: 0c3812c347bf ("s390/cio: derive cdev information only for IO-subchannels")
Cc: <stable@vger.kernel.org> # v5.15
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This reverts commit 19905240aef0181d1e6944070eb85fce75f75bcd.
It was a new feature, and it doesn't even work properly yet, so revert
it from this branch as it is not needed for 6.1-final.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@kernel.org>
Fixes: 19905240aef0 ("usb: gadget: uvc: limit isoc_sg to super speed gadgets")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some x86/ACPI laptops with MIPI cameras have a LATT2021 ACPI device
in the _DEP dependency list of the ACPI devices for the camera-sensors
(which have flags.honor_deps set).
The _DDN for the LATT2021 device is "Lattice FW Update Client Driver",
suggesting that this is used for firmware updates of something. There
is no Linux driver for this and if Linux gets support for updates it
will likely be in userspace through fwupd.
For now add the LATT2021 HID to acpi_ignore_dep_ids[] so that
acpi_dev_ready_for_enumeration() will return true once the other _DEP
dependencies are met.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Like the Asus Vivobook K3402ZA/K3502ZA/S5402ZA Asus Vivobook S5602ZA
has an ACPI DSDT table the describes IRQ 1 as ActiveLow while the kernel
overrides it to Edge_High. This prevents the keyboard on this laptop
from working. To fix this add this laptop to the skip_override_table so
that the kernel does not override IRQ 1.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216579
Tested-by: Dzmitry <wrkedm@gmail.com>
Signed-off-by: Tamim Khan <tamim@fusetak.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix an unintentional u32 overflow by changing PCC_CMD_WAIT_RETRIES_NUM
to 500ULL.
Fixes: 91cefefb6991 ("ACPI: PCC: replace wait_for_completion()")
Signed-off-by: Manank Patel <pmanank200502@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes: a3381e3a65cb ("PM / domains: Fix up domain-idle-states OF parsing")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
REGMAP_MMIO is not user-configurable, so we can only satisfy this
dependency by enabling some other Kconfig symbol that properly 'select's
it. Use select like everybody else.
Noticed when trying to enable this driver for compile testing.
Fixes: 59592cc1f593 ("mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221024180300.2292208-1-briannorris@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was
causing a harmless splat in ipa_idle_indication_cfg(), add a version
check to prevent trying to fetch this register on v3.1
Fixes: 6a244b75cfab ("net: ipa: introduce ipa_reg()")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask
values, when the hardware actually uses 8. Out of range values were
silently ignored before, so the IPA worked as expected. However the
new generalised register definitions introduce stricter checking here,
they now cause some splats and result in the value 0 being written
instead. Fix the limit bitmask widths so that the correct values can be
written.
Fixes: 1c418c4a929c ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|