| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
4 bug fixes for Cadence 3 driver.
The biggest fix is changing endpoint configuration method to
avoid FIFO overflow at multiple endpoints situation.
* tag 'usb-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: gadget: own the lock wrongly at the suspend routine
usb: cdns3: Fix on-chip memory overflow issue
usb: cdns3: gadget: suspicious implicit sign extension
usb: cdns3: Variable 'length' set but not used
|
|
When the system goes to suspend, if the controller is at device mode with
cable connecting to host, the call stack is: cdns3_suspend->
cdns3_gadget_suspend -> cdns3_disconnect_gadget, after cdns3_disconnect_gadget
is called, it owns lock wrongly, it causes the system being deadlock after
resume due to at cdns3_device_thread_irq_handler, it tries to get the lock,
but can't get it forever.
To fix it, we delete the unlock-lock operations at cdns3_disconnect_gadget,
and do it at the caller.
Fixes: b1234e3b3b26 ("usb: cdns3: add runtime PM support")
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Patch fixes issue caused setting On-chip memory overflow bit in usb_sts
register. The issue occurred because EP_CFG register was set twice
before USB_STS.CFGSTS was set. Every write operation on EP_CFG.BUFFERING
causes that controller increases internal counter holding the number
of reserved on-chip buffers. First time this register was updated in
function cdns3_ep_config before delegating SET_CONFIGURATION request
to class driver and again it was updated when class wanted to enable
endpoint. This patch fixes this issue by configuring endpoints
enabled by class driver in cdns3_gadget_ep_enable and others just
before status stage.
Cc: stable@vger.kernel.org#v5.8+
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The code:
trb->length = cpu_to_le32(TRB_BURST_LEN(priv_ep->trb_burst_size)
| TRB_LEN(length));
TRB_BURST_LEN(priv_ep->trb_burst_size) may be overflow for int 32 if
priv_ep->trb_burst_size is equal or larger than 0x80;
Below is the Coverity warning:
sign_extension: Suspicious implicit sign extension: priv_ep->trb_burst_size
with type u8 (8 bits, unsigned) is promoted in priv_ep->trb_burst_size << 24
to type int (32 bits, signed), then sign-extended to type unsigned long
(64 bits, unsigned). If priv_ep->trb_burst_size << 24 is greater than 0x7FFFFFFF,
the upper bits of the result will all be 1.
To fix it, it needs to add an explicit cast to unsigned int type for ((p) << 24).
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d74683627 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An incorrect sizeof() is being used, sizeof(rhub->ports) is not
correct, it should be sizeof(*rhub->ports). This bug did not
cause any issues because it just so happens the sizes are the same.
Fixes: bcaa9d5c5900 ("xhci: Create new structures to store xhci port information")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
chip->port_type and chip->pwr_opmode are enums and when GCC considers them
as unsigned, the conditions are never met.
This patch takes advantage of the ret variable and fixes the following
warnings:
drivers/usb/typec/stusb160x.c:548 stusb160x_get_fw_caps() warn: unsigned 'chip->port_type' is never less than zero.
drivers/usb/typec/stusb160x.c:570 stusb160x_get_fw_caps() warn: unsigned 'chip->pwr_opmode' is never less than zero.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028163309.12878-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When stusb160x driver is built as a module, no modalias information is
available, and it prevents the module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fix this issue.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028151703.31195-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
From: Bastien Nocera <hadess@hadess.net>
Contrary to the comment above the id table, we didn't implement a match
function. This meant that every single Apple device that was already
plugged in to the computer would have its device driver reprobed
when the apple-mfi-fastcharge driver was loaded, eg. the SD card reader
could be reprobed when the apple-mfi-fastcharge after pivoting root
during boot up and the module became available.
Make sure that the driver probe isn't being run for unsupported
devices by adding a match function that checks the product ID, in
addition to the id_table checking the vendor ID.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1878347
Link: https://lore.kernel.org/linux-usb/CAE3RAxt0WhBEz8zkHrVO5RiyEOasayy1QUAjsv-pB0fAbY1GSw@mail.gmail.com/
Fixes: 249fa8217b84 ("USB: Add driver to control USB fast charge for iOS devices")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
[m.v.b: Add Link and Reported-by tags to the commit message]
Reported-by: Pany <pany@fedoraproject.org>
Tested-by: Pan (Pany) YUAN <pany@fedoraproject.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20201022135521.375211-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
From: Bastien Nocera <hadess@hadess.net>
When a USB device driver has both an id_table and a match() function, make
sure to check both to find a match, first matching the id_table, then
checking the match() function.
This makes it possible to have module autoloading done through the
id_table when devices are plugged in, before checking for further
device eligibility in the match() function.
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Co-developed-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Pan (Pany) YUAN <pany@fedoraproject.org>
Link: https://lore.kernel.org/r/20201022135521.375211-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
tegra_ehci_probe().
Fixes: 79ad3b5add4a ("usb: host: Add EHCI driver for NVIDIA Tegra SoCs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20201026090657.49988-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The typec_register_port() function doesn't return NULL, it returns error
pointers.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201023114017.GE18329@kadam
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.
ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]
this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a4e7279cd1d1 ("cdc-acm: introduce a cool down") is causing
regression if there is some USB error, such as -EPROTO.
This has been reported on some samples of the Odroid-N2 using the Combee II
Zibgee USB dongle.
> struct acm *acm = container_of(work, struct acm, work)
is incorrect in case of a delayed work and causes warnings, usually from
the workqueue:
> WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:1474 __queue_work+0x480/0x528.
When this happens, USB eventually stops working completely after a while.
Also the ACM_ERROR_DELAY bit is never set, so the cooldown mechanism
previously introduced cannot be triggered and acm_submit_read_urb() is
never called.
This changes makes the cdc-acm driver use a single delayed work, fixing the
pointer arithmetic in acm_softint() and set the ACM_ERROR_DELAY when the
cooldown mechanism appear to be needed.
Fixes: a4e7279cd1d1 ("cdc-acm: introduce a cool down")
Cc: Oliver Neukum <oneukum@suse.com>
Reported-by: Pascal Vizeli <pascal.vizeli@nabucasa.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201019170702.150534-1-jbrunet@baylibre.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fsl_usb2_device_register() should stop init if dma_set_mask() return
error.
Fixes: cae058610465 ("drivers/usb/host: fsl: Set DMA_MASK of usb platform device")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201010060308.33693-1-ran.wang_1@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a common comment marked, instead, with kernel-doc
notation.
Also, some identifiers have different names between their
prototypes and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/0b964be3884def04fcd20ea5c12cb90d0014871c.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These variables are enums but in this situation GCC will treat them as
unsigned so the conditions are never true.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201023112412.GD282278@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch removes not used variable 'length' from
cdns3_wa2_descmiss_copy_data function.
Fixes: 141e70fef4ee ("usb: cdns3: gadget: need to handle sg case for workaround 2 case")
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.10-rc1
They include a lot of different things, all related to the driver core
and/or some driver logic:
- sysfs common write functions to make it easier to audit sysfs
attributes
- device connection cleanups and fixes
- devm helpers for a few functions
- NOIO allocations for when devices are being removed
- minor cleanups and fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
regmap: debugfs: use semicolons rather than commas to separate statements
platform/x86: intel_pmc_core: do not create a static struct device
drivers core: node: Use a more typical macro definition style for ACCESS_ATTR
drivers core: Use sysfs_emit for shared_cpu_map_show and shared_cpu_list_show
mm: and drivers core: Convert hugetlb_report_node_meminfo to sysfs_emit
drivers core: Miscellaneous changes for sysfs_emit
drivers core: Reindent a couple uses around sysfs_emit
drivers core: Remove strcat uses around sysfs_emit and neaten
drivers core: Use sysfs_emit and sysfs_emit_at for show(device *...) functions
sysfs: Add sysfs_emit and sysfs_emit_at to format sysfs output
dyndbg: use keyword, arg varnames for query term pairs
driver core: force NOIO allocations during unplug
platform_device: switch to simpler IDA interface
driver core: platform: Document return type of more functions
Revert "driver core: Annotate dev_err_probe() with __must_check"
Revert "test_firmware: Test platform fw loading on non-EFI systems"
iio: adc: xilinx-xadc: use devm_krealloc()
hwmon: pmbus: use more devres helpers
devres: provide devm_krealloc()
syscore: Use pm_pr_dbg() for syscore_{suspend,resume}()
...
|
|
In order to enable -Wimplicit-fallthrough for Clang[1], replace the
existing /* FALLTHROUGH */ comment with the new pseudo-keyword
macro fallthrough[2].
[1] https://git.kernel.org/linus/e2079e93f562c7f7a030eb7642017ee5eabaaa10
[2] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20201008222849.GA18634@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The QCOM SPMI typec driver handles the role and orientation detection, and
notifies client drivers using the USB role switch framework. It registers
as a typec port, so orientation can be communicated using the typec switch
APIs. The driver also attains a handle to the VBUS output regulator, so it
can enable/disable the VBUS source when acting as a host/device.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201008235934.8931-2-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.10-rc1
Here are the USB-serial updates for 5.10-rc1, including:
- new device ids
- various clean ups
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.10-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Cellient MPL200 card
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: serial: qcserial: fix altsetting probing
USB: serial: ftdi_sio: clean up jtag quirks
USB: serial: pl2303: add device-id for HP GC device
USB: serial: ftdi_sio: add support for FreeCalypso JTAG+UART adapters
|
|
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/3db5418fe9e516f4b290736c5a199c9796025e3c.1601715478.git.wilken.gottwalt@mailbox.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Upon receiving ALERT_EXTENDED.TCPC_SINK_FAST_ROLE_SWAP signal
tcpm to start Sink fast role swap signal.
Inform when TCPM is sourcing vbus.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-9-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement tcpc.enable_frs to enable TCPC to receive
Fast role swap signal.
Additionally set the sink disconnect threshold to 4v
to prevent disconnect during Fast Role swap.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.
Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.
Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.
TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.
4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.
The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.
Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/
usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.
Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
usbcore: registered new interface driver etas_es58x
usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: ES581.4
usb 1-1.1: Manufacturer: ETAS GmbH
usb 1-1.1: SerialNumber: 2204355
cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device
Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c
N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.
`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):
Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0159
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES581.4
iSerial 3 2204355
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0035
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 5 Bus Powered Configuration
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 4 ACM Control Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 0
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 10
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0168
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES582
iSerial 3 0108933
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0169
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES584.1
iSerial 3 0100320
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ftdi_determine_type() function had this construct in it to get the
number of the interface it is operating on:
inter = serial->interface->altsetting->desc.bInterfaceNumber;
Elsewhere in this driver cur_altsetting is used instead for this
purpose. Change ftdi_determine_type() to use cur_altsetting
for consistency.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[ johan: fix old style issues; drop braces and random white space ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This commit adds the following Telit FT980-KS composition:
0x1054: rndis, diag, adb, nmea, modem, modem, aux
AT commands can be sent to /dev/ttyUSB2.
Signed-off-by: Leonid Bloch <lb.workbox@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/ce86bc05-f4e2-b199-0cdc-792715e3f275@asocscloud.com
Link: https://lore.kernel.org/r/20201004155813.2342-1-lb.workbox@gmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
|
|
The latest reference to usbfs_conn_disc_event() removed in
commit fb28d58b72aa ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.
This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.
ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.
In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a function that converts power operation mode string into
power operation mode value.
It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms have only super speed data bus connected to this device
and high speed data bus directly connected to the SoC. In such platforms
modelling connector as a child of this device is making it non compliant
with usb connector bindings. By modelling connector node as standalone
device node along with this device and the SoC data bus will make it
compliant with usb connector bindings.
Update the driver to handle this model by using OF graph API to get the
connector fwnode and usb role switch class API to get role switch handle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200920134905.4370-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes: cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes: e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes: aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Add compatible string to use this generic glue layer to support
Intel Keem Bay platform's dwc3 controller.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
DWC3 IPs can use the maximum stream id (up to 2^16) specified by the
USB 3.x specs. Don't limit to stream id 2^15 only. Note that this does
not reflect the number of concurrent streams the controller handles
internally.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's not an error if the mode can't be entered because
another mode is already active, so no longer printing an
error message if that happens.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
