| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is a spelling mistake in a pr_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220923132103.2486724-1-colin.i.king@gmail.com
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20221123160719.3002694-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The newly defined ioctl BIODASDCOPYPAIRSWAP takes a structure that
specifies a copy pair that should be swapped. It will call the device
discipline function to perform the swap operation.
The structure looks as followed:
struct dasd_copypair_swap_data_t {
char primary[20];
char secondary[20];
__u8 reserved[64];
};
where primary is the old primary device that will be replaced by the
secondary device. The old primary will become a secondary device
afterwards.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20220920192616.808070-6-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix this:
drivers/s390/block/dasd_ioctl.c:666: warning:
Function parameter or member 'disk' not described in 'dasd_biodasdinfo'
drivers/s390/block/dasd_ioctl.c:666: warning:
Function parameter or member 'info' not described in 'dasd_biodasdinfo'
Acked-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove dasd ioctl debug printk which seems to be a leftover from the
very early days. At least it seems to be quite pointless.
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
We can just dereference the point in struct gendisk instead. Also
remove the now unused export.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that the hd_struct always has a block device attached to it, there is
no need for having two size field that just get out of sync.
Additionally the field in hd_struct did not use proper serialization,
possibly allowing for torn writes. By only using the block_device field
this problem also gets fixed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: Chao Yu <yuchao0@huawei.com> [f2fs]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Implement the ->set_read_only method instead of parsing the actual
ioctl command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a littler helper to make the somewhat arcane bd_contains checks a
little more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Two different callers use two different mutexes for updating the
block device size, which obviously doesn't help to actually protect
against concurrent updates from the different callers. In addition
one of the locks, bd_mutex is rather prone to deadlocks with other
parts of the block stack that use it for high level synchronization.
Switch to using a new spinlock protecting just the size updates, as
that is all we need, and make sure everyone does the update through
the proper helper.
This fixes a bug reported with the nvme revalidating disks during a
hot removal operation, which can currently deadlock on bd_mutex.
Reported-by: Xianting Tian <xianting_tian@126.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The IBM partition parser requires device type specific information only
available to the DASD driver to correctly register partitions. The
current approach of using ioctl_by_bdev with a fake user space pointer
is discouraged.
Fix this by replacing IOCTL calls with direct in-kernel function calls.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Prepare for in-kernel callers of this functionality.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[sth@de.ibm.com: remove leftover kfree]
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Userspace tools might have the need to release space for Extent Space
Efficient (ESE) volumes when working with such a device.
Provide the necessarry interface for such a task by implementing a new
ioctl BIODASDRAS. The ioctl uses the format_data_t data structure for
data input:
typedef struct format_data_t {
unsigned int start_unit; /* from track */
unsigned int stop_unit; /* to track */
unsigned int blksize; /* sectorsize */
unsigned int intensity;
} format_data_t;
If the intensity is set to 0x40, start_unit and stop_unit are ignored
and space for the entire volume is released. Otherwise, if intensity is
set to 0, the respective range is released (if possible).
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Since e443343e509a we haven't had a request_fn attached to
this driver, hence any code inside an if (q->request_fn) is
unreachable.
Fixes: e443343e509a ("s390/dasd: blk-mq conversion")
[sth: Keep and fix the dasd_info->chanq_len counter.]
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All the current architecture specific defines for these
are the same. Refactor these common defines to a common
header file.
The new common linux/compat_time.h is also useful as it
will eventually be used to hold all the defines that
are needed for compat time types that support non y2038
safe types. New architectures need not have to define these
new types as they will only use new y2038 safe syscalls.
This file can be deleted after y2038 when we stop supporting
non y2038 safe syscalls.
The patch also requires an operation similar to:
git grep "asm/compat\.h" | cut -d ":" -f 1 | xargs -n 1 sed -i -e "s%asm/compat.h%linux/compat.h%g"
Cc: acme@kernel.org
Cc: benh@kernel.crashing.org
Cc: borntraeger@de.ibm.com
Cc: catalin.marinas@arm.com
Cc: cmetcalf@mellanox.com
Cc: cohuck@redhat.com
Cc: davem@davemloft.net
Cc: deller@gmx.de
Cc: devel@driverdev.osuosl.org
Cc: gerald.schaefer@de.ibm.com
Cc: gregkh@linuxfoundation.org
Cc: heiko.carstens@de.ibm.com
Cc: hoeppner@linux.vnet.ibm.com
Cc: hpa@zytor.com
Cc: jejb@parisc-linux.org
Cc: jwi@linux.vnet.ibm.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: mark.rutland@arm.com
Cc: mingo@redhat.com
Cc: mpe@ellerman.id.au
Cc: oberpar@linux.vnet.ibm.com
Cc: oprofile-list@lists.sf.net
Cc: paulus@samba.org
Cc: peterz@infradead.org
Cc: ralf@linux-mips.org
Cc: rostedt@goodmis.org
Cc: rric@kernel.org
Cc: schwidefsky@de.ibm.com
Cc: sebott@linux.vnet.ibm.com
Cc: sparclinux@vger.kernel.org
Cc: sth@linux.vnet.ibm.com
Cc: ubraun@linux.vnet.ibm.com
Cc: will.deacon@arm.com
Cc: x86@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement new DASD IOCTL BIODASDCHECKFMT to check a range of tracks on a
DASD volume for correct formatting. The following characteristics are
checked:
- Block size
- ECKD key length
- ECKD record ID
- Number of records per track
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Convert the uses of pr_warning to pr_warn so there are fewer
uses of the old pr_warning.
Miscellanea:
o Align arguments
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently, dasd_format is calling the format logic of a DASD discipline
with PAV enabled. If that fails with an error code of -EAGAIN the value
of retries is decremented and the discipline function is called with PAV
turned off.
The loop is supposed to try this up to 255 times until success. However,
-EAGAIN can only occur once here and therefore the loop will never reach
the 255 retries.
So, replace the unnecessarily complicated loop logic and simply try again
without PAV enabled in case of an -EAGAIN error.
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rename enable_PAV to enable_pav.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Kernel panic or a hanging device during format if an alias device is
set offline or I/O errors occur.
Omit the error recovery procedure for alias devices and do retries on
the base device with full erp.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Whenever a DASD request encounters a timeout we might
need to abort all outstanding requests on this or
even other devices.
This is especially useful if one wants to fail all
devices on one side of a RAID10 configuration, even
though only one device exhibited an error.
To handle this I've introduced a new device flag
DASD_FLAG_ABORTIO.
This flag is evaluated in __dasd_process_request_queue()
and will invoke blk_abort_request() for all
outstanding requests with DASD_CQR_FLAGS_FAILFAST set.
This will cause any of these requests to be aborted
immediately if the blk_timeout function is activated.
The DASD_FLAG_ABORTIO is also evaluated in
__dasd_process_request_queue to abort all
new request which would have the
DASD_CQR_FLAGS_FAILFAST bit set.
The flag can be set with the new ioctls 'BIODASDABORTIO'
and removed with 'BIODASDALLOWIO'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Reorganize format IO requests and enable usage of PAV.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Let the dasd driver and qdio use ccw_device_get_schid and
get rid of other similar functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For non-existent ioctls -ENOTTY should be returned.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For unimplemented ioctls the dasd driver should return -ENOTTY.
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
The new is_compat_task() define for the !COMPAT case in
include/linux/compat.h conflicts with a similar define in
arch/s390/include/asm/compat.h.
This is the minimal patch which fixes the build issues.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Data is only used to temporarily hold information to be copied to the user
level, so it should be freed before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch extends the DASD statistics to allow for a more detailed
analysis of DASD I/O operations. In particular we want the statistics
to provide answers to the following questions:
- How many requests used a PAV alias?
- How many requests used High Performance FICON?
- How do read request perform versus write requests?
The existing DASD statistics interface has several shortcomings
- The interface for global data is a formatted text table in procfs
(/proc/dasd/statistics). The layout is meant for human readers and
is not to easy to parse. If values get to large for the table
layout, they get scaled down.
- The statistics which are collected per block device can be
accessed via an ioctl interface, which can only be extended by
defining a new ioctl.
- There is no statistics interface for individual PAV base and alias
devices.
To overcome theses shortcomings we create a new DASD statistics
interface in debugfs. This interface will contain one entry for global
data, one per DASD block device, and one per DASD base and alias
device. Each file contains the statistic data in easy to parse
name/value and name/array pairs. The existing interfaces will remain
functional, but they will not be extended.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The dasd_open function uses the private_data pointer of the gendisk to
find the dasd_block structure that matches the gendisk. When a DASD
device is set offline, we set the private_data pointer of the gendisk
to NULL and later remove the dasd_block structure, but there is still
a small race window, in which dasd_open could first read a pointer
from the private_data field and then try to use it, after the structure
has already been freed.
To close this race window, we will store a pointer to the dasd_devmap
structure of the base device in the private_data field. The devmap
entries are not deleted, and we already have proper locking and
reference counting in place, so that we can safely get from a devmap
pointer to the dasd_device and dasd_block structures of the device.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The dasd and dcssblk drivers gained the big
kernel lock in the recent pushdown from the
block layer, but they don't really need it,
so remove the calls without a replacement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fix possible NULL pointer in DASD messages and correct discipline
checking.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Most of the error conditions reported by a FICON storage server
indicate situations which can be recovered. Sometimes the host just
needs to retry an I/O request, but sometimes the recovery
is more complex and requires the device driver to wait, choose
a different path, etc.
The DASD device driver has a fully featured error recovery
for normal block layer I/O, but not for internal I/O request which
are for example used during the device bring up.
This can lead to situations where the IPL of a system fails because
DASD devices are not properly recognized.
This patch will extend the internal I/O handling to use the existing
error recovery procedures.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch fixes message naming so that generic dasd messages do not
contain the device discipline. For this purpose the dev_ makros are
replaced by pr_ makros for generic dasd messages.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Moved some Messages into s390 debug feature and changed remaining
messages to use the dev_xxx and pr_xxx macros.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The dasd device driver will now support ECKD devices with more then
65520 cylinders.
In the traditional ECKD adressing scheme each track is addressed
by a 16-bit cylinder and 16-bit head number. The new addressing
scheme makes use of the fact that the actual number of heads is
never larger then 15, so 12 bits of the head number can be redefined
to be part of the cylinder address.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
All of the ioctls are compatible. Just enable them.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
->compat_ioctl() actually had been useless here; generic
logics works fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Parallel access volumes (PAV) is a storage server feature, that allows
to start multiple channel programs on the same DASD in parallel. It
defines alias devices which can be used as alternative paths to the
same disk. With the old base PAV support we only needed rudimentary
functionality in the DASD device driver. As the mapping between base
and alias devices was static, we just had to export an identifier
(uid) and could leave the combining of devices to external layers
like a device mapper multipath.
Now hyper PAV removes the requirement to dedicate alias devices to
specific base devices. Instead each alias devices can be combined with
multiple base device on a per request basis. This requires full
support by the DASD device driver as now each channel program itself
has to identify the target base device.
The changes to the dasd device driver and the ECKD discipline are:
- Separate subchannel device representation (dasd_device) from block
device representation (dasd_block). Only base devices are block
devices.
- Gather information about base and alias devices and possible
combinations.
- For each request decide which dasd_device should be used (base or
alias) and build specific channel program.
- Support summary unit checks, which allow the storage server to
upgrade / downgrade between base and hyper PAV at runtime (support
is mandatory).
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The function shouldn't have existed in the first place (not MSS-aware).
Introduce a new function ccw_device_get_id() that extracts the
ccw_dev_id structure of a ccw device and convert all users of
_ccw_device_get_device_number to ccw_device_get_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Dasd code cleanup: 1) remove white space, 2) remove the emacs override
sections, and 3) use kzalloc instead of kmalloc.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Cast the argument correctly.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
