summaryrefslogtreecommitdiffstats
path: root/drivers/pinctrl/qcom/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2022-10-17pinctrl: qcom: add sdm670 pinctrlRichard Acayan1-0/+10
The Snapdragon 670 has a Top-Level Mode Multiplexer (TLMM) for various features. Add a driver to support it. Link: https://android.googlesource.com/kernel/msm/+/de5a12173c7fa6d65bedee9ad36af55b2dbfeb36%5E%21/#F6 Link: https://android.googlesource.com/kernel/msm/+/04f083156d9b9f3bfcf204c1c6da88632fbb3863%5E%21/#F22 Link: https://android.googlesource.com/kernel/msm/+/54837652e3400ecc63ccc78b2193faf4f349a32e%5E%21/#F0 Link: https://android.googlesource.com/kernel/msm/+/f0409b07174ceca217f8b7fd255418feff06092d%5E%21/#F0 Signed-off-by: Richard Acayan <mailingradian@gmail.com> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221014001934.4995-4-mailingradian@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-10-04pinctrl: qcom: restrict drivers per ARM/ARM64Krzysztof Kozlowski1-0/+39
There is no point to allow selecting pin-controller drivers for Qualcomm ARMv7 SoCs when building ARM64 kernel, and vice versa. This makes kernel configuration more difficult as many do not remember the Qualcomm SoCs. There won't be a single image for ARMv7 and ARMv8/9 SoCs, so no features/options are lost. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220925112103.148836-1-krzysztof.kozlowski@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-08-25pinctrl: qcom: Add sc8280xp lpass lpi pinctrl driverSrinivas Kandagatla1-0/+9
Add pinctrl driver to support pin configuration for LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl on SC8280XP. This IP is an additional pin control block for Audio Pins on top the existing SoC Top level pin-controller. Hardware setup looks like: TLMM GPIO[189 - 207] --> LPASS LPI GPIO [0 - 18] This pin controller has some similarities compared to Top level msm SoC Pin controller like 'each pin belongs to a single group' and so on. However this one is intended to control only audio pins in particular, which can not be configured/touched by the Top level SoC pin controller except setting them as gpios. Apart from this, slew rate is also available in this block for certain pins which are connected to SLIMbus or SoundWire Bus. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220817113747.9111-3-srinivas.kandagatla@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-08-25pinctrl: qcom: Add sm8450 lpass lpi pinctrl driverSrinivas Kandagatla1-0/+9
Add pinctrl driver to support pin configuration for LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl on SM8450. This IP is an additional pin control block for Audio Pins on top the existing SoC Top level pin-controller. Hardware setup looks like: TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22] This pin controller has some similarities compared to Top level msm SoC Pin controller like 'each pin belongs to a single group' and so on. However this one is intended to control only audio pins in particular, which can not be configured/touched by the Top level SoC pin controller except setting them as gpios. Apart from this, slew rate is also available in this block for certain pins which are connected to SLIMbus or SoundWire Bus. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220817113833.9625-3-srinivas.kandagatla@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-08-03pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSMJohn Garry1-1/+1
All the many other configs depend on config PINCTRL_MSM, yet for config PINCTRL_SM8450 we select config PINCTRL_MSM. Make config PINCTRL_SM8450 depend on PINCTRL_MSM to be consistent with the rest. Signed-off-by: John Garry <john.garry@huawei.com> Suggested-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/1658829764-124936-1-git-send-email-john.garry@huawei.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-07-26pinctrl: qcom: Add SM6375 TLMM driverKonrad Dybcio1-0/+9
Add a driver to control the TLMM block on SM6375. This is an adapted version of msm-5.4's pinctrl-blair driver. Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20220716192900.454653-2-konrad.dybcio@somainline.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-07-11pinctrl: qcom: Add pinctrl driver for MSM8909Stephan Gerhold1-0/+8
Make it possible to control pins using the TLMM block in the MSM8909 SoC by adding the necessary definitions for GPIOs, groups and functions. The driver is originally taken from the msm-4.9 release [1] from Qualcomm, but cleaned up significantly with several fixes and clarifications. [1]: https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LF.UM.8.7-22500-8x09.0/drivers/pinctrl/qcom/pinctrl-msm8909.c Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220628145502.4158234-3-stephan.gerhold@kernkonzept.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-23pinctrl: qcom: Add SC7280 lpass pin configurationSrinivasa Rao Mandadapu1-0/+9
Add pin control support for SC7280 LPASS LPI. Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/1650285427-19752-7-git-send-email-quic_srivasam@quicinc.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-23pinctrl: qcom: Extract chip specific LPASS LPI codeSrinivasa Rao Mandadapu1-0/+9
Extract the chip specific SM8250 data from the LPASS LPI pinctrl driver to allow reusing the common code in the addition of subsequent platforms. Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/1650285427-19752-6-git-send-email-quic_srivasam@quicinc.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-23pinctrl: qcom: Update lpi pin group custiom functions with framework generic ↵Srinivasa Rao Mandadapu1-0/+1
functions Update custom pin group structure members with framework generic group_desc structure and replace the driver's custom pinctrl_ops with framework provided generic pin control group functions to avoid redundant code written in lpass lpi driver. Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/1650285427-19752-5-git-send-email-quic_srivasam@quicinc.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-03-15pinctrl: qcom: Introduce sc8280xp TLMM driverBjorn Andersson1-0/+9
The SC8280XP comes, like all other Qualcomm platforms, with a TLMM block, so add a driver for it. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220308221132.1423218-2-bjorn.andersson@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-12-09pinctrl: qcom: Add SM8450 pinctrl driverVinod Koul1-0/+9
This adds pincontrol driver for tlmm block found in SM8450 SoC This patch is based on initial code downstream by Elliot Berman <eberman@codeaurora.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20211201072434.3968768-3-vkoul@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-11-27Merge tag 'v5.16-rc2' into develLinus Walleij1-0/+2
Linux 5.16-rc2 is needed because nonurgent fixes headed for next are strongly textually dependent on a fix that was applied for rc2. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-11-21pinctrl: qcom: Add SDX65 pincontrol driverVamsi Krishna Lanka1-0/+9
Add initial Qualcomm SDX65 pinctrl driver to support pin configuration with pinctrl framework for SDX65 SoC. Signed-off-by: Vamsi Krishna Lanka <quic_vamslank@quicinc.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/13acb3cb36349487dee9745ab040d8f1344d2096.1637048107.git.quic_vamslank@quicinc.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-11-16pinctrl: qcom: fix unmet dependencies on GPIOLIB for GPIOLIB_IRQCHIPJulian Braha1-0/+2
When PINCTRL_QCOM_SPMI_PMIC or PINCTRL_QCOM_SSBI_PMIC is selected, and GPIOLIB is not selected, Kbuild gives the following warnings: WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP Depends on [n]: GPIOLIB [=n] Selected by [y]: - PINCTRL_QCOM_SPMI_PMIC [=y] && PINCTRL [=y] && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && OF [=y] && SPMI [=y] WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP Depends on [n]: GPIOLIB [=n] Selected by [y]: - PINCTRL_QCOM_SSBI_PMIC [=y] && PINCTRL [=y] && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && OF [=y] This is because these config options enable GPIOLIB_IRQCHIP without selecting or depending on GPIOLIB, despite GPIOLIB_IRQCHIP depending on GPIOLIB. These unmet dependency bugs were detected by Kismet, a static analysis tool for Kconfig. Please advise if this is not the appropriate solution. Signed-off-by: Julian Braha <julianbraha@gmail.com> Link: https://lore.kernel.org/r/20211029004610.35131-1-julianbraha@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-11-05Merge tag 'pinctrl-v5.16-1' of ↵Linus Torvalds1-0/+17
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "The most interesting aspect is that we now have initial support for the Apple pin controller as used in the M1 laptops and the iPhones which is a step forward for using Linux efficiently on this Apple silicon. Core changes: - Add infrastructure for per-parent interrupt data to support the Apple pin controller. New drivers: - New combined pin control and GPIO driver for the Apple SoC. This is used in all modern Apple silicon such as the M1 laptops but also in at least recent iPhone variants. - New subdriver for the Qualcomm SM6350 - New subdriver for the Qualcomm QCM2290 - New subdriver for the Qualcomm PM6350 - New subdriver for the Uniphier NX1 - New subdriver for the Samsung ExynosAutoV9 - New subdriver for the Mediatek MT7986 - New subdriver for the nVidia Tegra194 Improvements: - Improve power management in the Mediatek driver. - Improvements to the Renesas internal consistency checker. - Convert the Rockchip pin control device tree bindings to YAML. - Finally convert the Qualcomm PMIC SSBI and SPMI MPP GPIO driver to use hierarchical interrupts. - Convert the Qualcomm PMIC MPP device tree bindings to YAML" * tag 'pinctrl-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (55 commits) pinctrl: add pinctrl/GPIO driver for Apple SoCs dt-bindings: pinctrl: Add apple,npins property to apple,pinctrl dt-bindings: pinctrl: add #interrupt-cells to apple,pinctrl gpio: Allow per-parent interrupt data pinctrl: tegra: Fix warnings and error pinctrl: intel: Kconfig: Add configuration menu to Intel pin control pinctrl: tegra: Use correct offset for pin group pinctrl: core: fix possible memory leak in pinctrl_enable() pinctrl: bcm2835: Allow building driver as a module pinctrl: equilibrium: Fix function addition in multiple groups pinctrl: tegra: Add pinmux support for Tegra194 pinctrl: tegra: include lpdr pin properties pinctrl: mediatek: add support for MT7986 SoC dt-bindings: pinctrl: update bindings for MT7986 SoC pinctrl: microchip sgpio: use reset driver dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add reset binding dt-bindings: pinctrl: qcom,pmic-mpp: switch to #interrupt-cells pinctrl: qcom: spmi-mpp: add support for hierarchical IRQ chip pinctrl: qcom: spmi-mpp: hardcode IRQ counts pinctrl: qcom: ssbi-mpp: add support for hierarchical IRQ chip ...
2021-10-07qcom_scm: hide Kconfig symbolArnd Bergmann1-1/+2
Now that SCM can be a loadable module, we have to add another dependency to avoid link failures when ipa or adreno-gpu are built-in: aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe': ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available' ld.lld: error: undefined symbol: qcom_scm_is_available >>> referenced by adreno_gpu.c >>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a This can happen when CONFIG_ARCH_QCOM is disabled and we don't select QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd use a similar dependency here to what we have for QCOM_RPROC_COMMON, but that causes dependency loops from other things selecting QCOM_SCM. This appears to be an endless problem, so try something different this time: - CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on' but that is simply selected by all of its users - All the stubs in include/linux/qcom_scm.h can go away - arm-smccc.h needs to provide a stub for __arm_smccc_smc() to allow compile-testing QCOM_SCM on all architectures. - To avoid a circular dependency chain involving RESET_CONTROLLER and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement. According to my testing this still builds fine, and the QCOM platform selects this symbol already. Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Alex Elder <elder@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-09-23pinctrl: qcom: Add QCM2290 pinctrl driverShawn Guo1-0/+8
It's a porting of pinctrl-scuba driver from CAF msm-4.19 kernel. The egpio and wake bits are removed. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210923033224.29719-3-shawn.guo@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-09-23pinctrl: qcom: Add SM6350 pinctrl driverKonrad Dybcio1-0/+9
This adds pincontrol driver for tlmm block found in SM6350 SoC This patch is based on downstream copyleft code. Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210923161450.15278-2-konrad.dybcio@somainline.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-09-02Merge tag 'pinctrl-v5.15-1' of ↵Linus Torvalds1-0/+17
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.15 kernel cycle, no core changes at all this time, just driver work! New drivers: - New subdriver for Intel Keem Bay (an ARM-based SoC) - New subdriver for Qualcomm MDM9607 and SM6115 - New subdriver for ST Microelectronics STM32MP135 - New subdriver for Freescale i.MX8ULP ("Ultra Low Power") - New subdriver for Ingenic X2100 - Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO - Support Samsung Exynos850 - Support Renesas RZ/G2L Enhancements: - A major refactoring of the Rockchip driver, breaking part of it out to a separate GPIO driver in drivers/gpio - Pin bias support on Renesas r8a77995 - Add SCI pins support to Ingenic JZ4755 and JZ4760 - Mediatek device tree bindings converted to YAML" * tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits) pinctrl: renesas: Add RZ/G2L pin and gpio controller driver pinctrl: samsung: Add Exynos850 SoC specific data dt-bindings: pinctrl: samsung: Add Exynos850 doc MAINTAINERS: Add maintainers for amd-pinctrl driver pinctrl: Add Intel Keem Bay pinctrl driver dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments dt-bindings: mediatek: convert pinctrl to yaml arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl pinctrl: ingenic: Add .max_register in regmap_config pinctrl: ingenic: Fix bias config for X2000(E) pinctrl: ingenic: Fix incorrect pull up/down info pinctrl: Ingenic: Add pinctrl driver for X2100. dt-bindings: pinctrl: Add bindings for Ingenic X2100. pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760. pinctrl: Ingenic: Improve the code. ...
2021-07-31drivers: qcom: pinctrl: Add pinctrl driver for sm6115Iskren Chernev1-0/+9
Based on CAF implementation with egpio/wake_reg support removed. Similar function names were merged to reduce total number of functions. Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210723192352.546902-3-iskren.chernev@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-23pinctrl: qcom: Add MDM9607 pinctrl driverKonrad Dybcio1-0/+8
Add a pinctrl driver to allow for managing SoC pins. Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210624191743.617073-2-konrad.dybcio@somainline.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-23pinctrl: qcom: fix GPIOLIB dependenciesArnd Bergmann1-32/+31
Enabling the PINCTRL_SM8350 symbol without GPIOLIB or SCM causes a build failure: WARNING: unmet direct dependencies detected for PINCTRL_MSM Depends on [m]: PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && (QCOM_SCM [=m] || !QCOM_SCM [=m]) Selected by [y]: - PINCTRL_SM8350 [=y] && PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && OF [=y] aarch64-linux-ld: drivers/pinctrl/qcom/pinctrl-msm.o: in function `msm_gpio_irq_set_type': pinctrl-msm.c:(.text.msm_gpio_irq_set_type+0x1c8): undefined reference to `qcom_scm_io_readl' The main problem here is the 'select PINCTRL_MSM', which needs to be a 'depends on' as it is for all the other front-ends. As the GPIOLIB dependency is now implied by that, symbol, remove the duplicate dependencies in the process. Fixes: d5d348a3271f ("pinctrl: qcom: Add SM8350 pinctrl driver") Fixes: 376f9e34c10f ("drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIB") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210723091400.1669716-1-arnd@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-01Merge tag 'pinctrl-v5.14-1' of ↵Linus Torvalds1-0/+9
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.14 kernel. Not so much going on. No core changes, just drivers. The most interesting would be that MIPS Ralink is migrating to pin control and we have some bindings but not yet code for the Apple M1 pin controller. New drivers: - Last merge window we created a driver for the Ralink RT2880. We are now moving the Ralink SoC pin control drivers out of the MIPS architecture code and into the pin control subsystem. This concerns RT288X, MT7620, RT305X, RT3883 and MT7621. - Qualcomm SM6125 SoC pin control driver. - Qualcomm spmi-gpio support for PM7325. - Qualcomm spmi-mpp also handles PMI8994 (just a compatible string) - Mediatek MT8365 SoC pin controller. - New device HID for the AMD GPIO controller. Improvements: - Pin bias config support for a slew of Renesas pin controllers. - Incremental improvements and non-urgent bug fixes to the Renesas SoC drivers. - Implement irq_set_wake on the AMD pin controller so we can wake up from external pin events. Misc: - Devicetree bindings for the Apple M1 pin controller, we will probably see a proper driver for this soon as well" * tag 'pinctrl-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (54 commits) pinctrl: ralink: rt305x: add missing include pinctrl: stm32: check for IRQ MUX validity during alloc() pinctrl: zynqmp: some code cleanups drivers: qcom: pinctrl: Add pinctrl driver for sm6125 dt-bindings: pinctrl: qcom: sm6125: Document SM6125 pinctrl driver dt-bindings: pinctrl: mcp23s08: add documentation for reset-gpios pinctrl: mcp23s08: Add optional reset GPIO pinctrl: mediatek: fix mode encoding pinctrl: mcp23s08: Fix missing unlock on error in mcp23s08_irq() pinctrl: bcm: Constify static pinmux_ops pinctrl: bcm: Constify static pinctrl_ops pinctrl: ralink: move RT288X SoC pinmux config into a new 'pinctrl-rt288x.c' file pinctrl: ralink: move MT7620 SoC pinmux config into a new 'pinctrl-mt7620.c' file pinctrl: ralink: move RT305X SoC pinmux config into a new 'pinctrl-rt305x.c' file pinctrl: ralink: move RT3883 SoC pinmux config into a new 'pinctrl-rt3883.c' file pinctrl: ralink: move MT7621 SoC pinmux config into a new 'pinctrl-mt7621.c' file pinctrl: ralink: move ralink architecture pinmux header into the driver pinctrl: single: config: enable the pin's input pinctrl: mtk: Fix mt8365 Kconfig dependency pinctrl: mcp23s08: fix race condition in irq handler ...
2021-06-18drivers: qcom: pinctrl: Add pinctrl driver for sm6125Martin Botka1-0/+9
This patch adds pinctrl driver for sm6125. Signed-off-by: Martin Botka <martin.botka@somainline.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210614172713.558192-2-martin.botka@somainline.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-06-09pinctrl: qcom: Make it possible to select SC8180x TLMMBjorn Andersson1-1/+1
It's currently not possible to select the SC8180x TLMM driver, due to it selecting PINCTRL_MSM, rather than depending on the same. Fix this. Fixes: 97423113ec4b ("pinctrl: qcom: Add sc8180x TLMM driver") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210608180702.2064253-1-bjorn.andersson@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-04-14drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIBJulian Braha1-1/+1
When PINCTRL_MSM is enabled, and GPIOLIB is disabled, Kbuild gives the following warning: WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP Depends on [n]: GPIOLIB [=n] Selected by [y]: - PINCTRL_MSM [=y] && PINCTRL [=y] && (ARCH_QCOM || COMPILE_TEST [=y]) This is because PINCTRL_MSM selects GPIOLIB_IRQCHIP, without selecting or depending on GPIOLIB, despite GPIOLIB_IRQCHIP depending on GPIOLIB. Having PINCTRL_MSM select GPIOLIB will cause a recursive dependency error. Signed-off-by: Julian Braha <julianbraha@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210414025138.480085-1-julianbraha@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-15pinctrl: qcom: sc8180x: add ACPI probe supportShawn Guo1-1/+1
It adds ACPI probe support for pinctrl-sc8180x driver. We have one problem with ACPI table, i.e. GIO0 (TLMM) block has one single memory resource to cover 3 tiles defined by SC8180X. To follow the hardware layout of 3 tiles which is already supported DT probe, it adds one function to replace the original single memory resource with 3 named ones for tiles. With that, We can map memory for ACPI in the same way as DT. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com> Link: https://lore.kernel.org/r/20210311024102.15450-1-shawn.guo@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-02-12pinctrl: qcom: Add sc8180x TLMM driverBjorn Andersson1-0/+9
Add pinctrl driver for the sc8180x TLMM block. A noteworthy difference from previous TLMM blocks is that the registers for GPIO 177 through 189 are for some reason offset from the typical layout. Other than that the driver is same old... Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210126042650.1725176-3-bjorn.andersson@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-02-12pinctrl: qcom: Add SM8350 pinctrl driverVinod Koul1-0/+9
This adds pincontrol driver for tlmm block found in SM8350 SoC This patch is based on initial code downstream by Raghavendra. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20210205140132.274242-3-vkoul@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-12-05pinctrl: qcom: Add sm8250 lpass lpi pinctrl driverSrinivas Kandagatla1-0/+11
Add initial pinctrl driver to support pin configuration for LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl on SM8250. This IP is an additional pin control block for Audio Pins on top the existing SoC Top level pin-controller. Hardware setup looks like: TLMM GPIO[146 - 159] --> LPASS LPI GPIO [0 - 13] This pin controller has some similarities compared to Top level msm SoC Pin controller like 'each pin belongs to a single group' and so on. However this one is intended to control only audio pins in particular, which can not be configured/touched by the Top level SoC pin controller except setting them as gpios. Apart from this, slew rate is also available in this block for certain pins which are connected to SLIMbus or SoundWire Bus. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20201202163443.26499-3-srinivas.kandagatla@linaro.org [Add some dependencies] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-24pinctrl: qcom: Add sc7280 pinctrl driverRajendra Nayak1-0/+9
Add initial pinctrl driver to support pin configuration with pinctrl framework for SC7280 SoC Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1604570192-15057-2-git-send-email-rnayak@codeaurora.org [Change select PINCTRL_MSM to depends on PINCTRL_MSM] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-24pinctrl: qcom: Fix msm8953 Kconfig entry to depend on, not select PINCTRL_MSMJohn Stultz1-1/+1
One fixup following my patch commit be117ca32261 ("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a selected config") being queued in LinusW's tree, as a new config entry was added for the msm8953 that also needs the change. Applies to LinusW's pinctrl devel tree. Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Prasad Sodagudi <psodagud@codeaurora.org> Cc: Vladimir Lypak <junak.pub@gmail.com> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20201110215619.86076-1-john.stultz@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-11pinctrl: qcom: sdx55: update kconfig dependencyVinod Koul1-1/+1
Commit be117ca32261 ("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a dependency rather then a selected config") moved the qcom pinctrl drivers to have PINCTRL_MSM as dependency rather then a selected config, so do this change for SDX55 pinctrl driver as well. Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20201111043610.177168-1-vkoul@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: qcom: Add SDX55 pincontrol driverJeevan Shriram1-0/+9
Add initial Qualcomm SDX55 pinctrl driver to support pin configuration with pinctrl framework for SDX55 SoC. [ported from downstream and tidy up] Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20201109062620.14566-3-vkoul@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: qcom: Allow pinctrl-msm code to be loadable as a moduleJohn Stultz1-1/+2
Tweaks to allow pinctrl-msm code to be loadable as a module. This is needed in order to support having the qcom-scm driver, which pinctrl-msm calls into, configured as a module. This requires that we tweak Kconfigs selecting PINCTRL_MSM to also depend on QCOM_SCM || QCOM_SCM=n so that we match the module setting of QCOM_SCM. Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Joerg Roedel <joro@8bytes.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <maz@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Maulik Shah <mkshah@codeaurora.org> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-arm-msm@vger.kernel.org Cc: iommu@lists.linux-foundation.org Cc: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20201106042710.55979-2-john.stultz@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a ↵John Stultz1-24/+24
selected config This patch reworks PINCTRL_MSM to be a visible option, and instead of having the various SoC specific drivers select PINCTRL_MSM, this switches those configs to depend on PINCTRL_MSM. This is useful, as it will be needed in order to cleanly support having the qcom-scm driver, which pinctrl-msm calls into, configured as a module. Without this change, we would eventually have to add dependency lines to every config that selects PINCTRL_MSM, and that would becomes a maintenance headache. We also add PINCTRL_MSM to the arm64 defconfig to avoid surprises as otherwise PINCTRL_MSM/IPQ* options previously enabled, will be off. Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Joerg Roedel <joro@8bytes.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <maz@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Maulik Shah <mkshah@codeaurora.org> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-arm-msm@vger.kernel.org Cc: iommu@lists.linux-foundation.org Cc: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20201106042710.55979-1-john.stultz@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: qcom: add pinctrl driver for msm8953Vladimir Lypak1-0/+10
Add inititial pinctrl driver for MSM8953 platform. Compatible SoCs are: MSM8953, APQ8053, SDM(SDA)450, SDM(SDA)632. Based off CAF implementation. Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Vladimir Lypak <junak.pub@gmail.com> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20201007160611.942754-1-junak.pub@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-08-27pinctrl: qcom: Add msm8226 pinctrl driver.Bartosz Dudziak1-0/+9
Add initial Qualcomm msm8226 pinctrl driver to support pin configuration with pinctrl framework for msm8226 SoC. - Initial formatting and style was taken from the msm8x74 pinctrl driver added by Björn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl> Link: https://lore.kernel.org/r/20200716205530.22910-3-bartosz.dudziak@snejp.pl Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-16pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180Douglas Anderson1-0/+2
Depending on how you look at it, you can either say that: a) There is a PDC hardware issue (with the specific IP rev that exists on sc7180) that causes the PDC not to work properly when configured to handle dual edges. b) The dual edge feature of the PDC hardware was only added in later HW revisions and thus isn't in all hardware. Regardless of how you look at it, let's work around the lack of dual edge support by only ever letting our parent see requests for single edge interrupts on affected hardware. NOTE: it's possible that a driver requesting a dual edge interrupt might get several edges coalesced into a single IRQ. For instance if a line starts low and then goes high and low again, the driver that requested the IRQ is not guaranteed to be called twice. However, it is guaranteed that once the driver's interrupt handler starts running its first instruction that any new edges coming in will cause the interrupt to fire again. This is relatively commonplace for dual-edge gpio interrupts (many gpio controllers require software to emulate dual edge with single edge) so client drivers should be setup to handle it. Fixes: e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200714080254.v3.1.Ie0d730120b232a86a4eac1e2909bcbec844d1766@changeid Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-28pinctrl: qcom: Add sm8250 pinctrl driver.Venkata Narendra Kumar Gutta1-0/+9
Add initial Qualcomm SM8250 pinctrl driver to support pin configuration with pinctrl framework for SM8250 SoC. Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org> Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org> Link: https://lore.kernel.org/r/1586477057-7636-2-git-send-email-vnkgutta@codeaurora.org [bjorn: Regrouped functions, upstream tiles implementation, dropped downstream-only features] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200417061907.1226490-3-bjorn.andersson@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-02-14pinctrl: qcom: Add ipq6018 pinctrl driverSricharan R1-0/+10
Add initial pinctrl driver to support pin configuration with pinctrl framework for ipq6018. Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> Link: https://lore.kernel.org/r/1579439601-14810-3-git-send-email-sricharan@codeaurora.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-21pinctrl: Fix Kconfig indentationKrzysztof Kozlowski1-46/+46
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/1574306382-32516-1-git-send-email-krzk@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-10-16pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956AngeloGioacchino Del Regno1-0/+10
Add the pinctrl driver to support pin configuration with the pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076. Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com> Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-10-03pinctrl: ssbi-gpio: convert to hierarchical IRQ helpers in gpio coreBrian Masney1-0/+1
Now that the GPIO core has support for hierarchical IRQ chips, convert Qualcomm's ssbi-gpio over to use these new helpers to reduce duplicated code across drivers. Signed-off-by: Brian Masney <masneyb@onstation.org> Link: https://lore.kernel.org/r/20190914111010.24384-1-masneyb@onstation.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-19Merge tag 'pinctrl-v5.4-1' of ↵Linus Torvalds1-0/+9
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.4 kernel cycle: Core changes: - Fix errors in example code in the documentation. New drivers: - Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the Ingenic driver. - Support Cirrus Logic Madera CS47L92 and CS47L15. - Support Allwinner Sunxi V3S. - Support Aspeed 2600 BMC. - Support Qualcomm SC7180. - Support Marvell MVEBU CS115. Driver improvements: - Clean up a few drivers to use the devm_platform_ioremap_resource() helper. - Pass the irqchip when registering the gpio_chip in some pin controllers that are also GPIO controllers. - Support suspend/resume in the Tegra driver. - Support pull-up on the Broadcom BCM2711. - The Intel driver can now request locked pads. - Fix the UFS reset pin in the Qualcomm SDM845 driver" * tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits) pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux() pinctrl: bcm: remove redundant assignment to pointer log pinctrl: iproc: Add 'get_direction' support pinctrl: iproc-gpio: Handle interrupts for multiple instances pinctrl: iproc-gpio: Fix incorrect pinconf configurations pinctrl: intel: mark intel_pin_to_gpio __maybe_unused pinctrl: qcom: sdm845: Fix UFS_RESET pin pinctrl: mvebu: add additional variant for standalone CP115 pinctrl: mvebu: Add CP110 missing pin functionality dt-bindings: cp110: document the new CP115 pinctrl compatible pinctrl: bcm2835: Pass irqchip when adding gpiochip pinctrl: meson: meson: Add of_node_put() before return pinctrl/gpio: Take MUX usage into account dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support pinctrl: amd: disable spurious-firing GPIO IRQs pinctrl: rza2: Include the appropriate headers pinctrl: rza2: Drop driver use of consumer flags ...
2019-08-15qcom: spmi-gpio: convert to hierarchical IRQ helpers in gpio coreBrian Masney1-0/+1
Now that the GPIO core has support for hierarchical IRQ chips, convert Qualcomm's spmi-gpio over to use these new helpers to reduce duplicated code across drivers. This change was tested on a LG Nexus 5 (hammerhead) phone. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-3-linus.walleij@linaro.org
2019-08-07pinctrl: qcom: Add SC7180 pinctrl driverJitendra Sharma1-0/+9
Add initial pinctrl driver to support pin configuration with pinctrl framework for SC7180 Signed-off-by: Jitendra Sharma <shajit@codeaurora.org> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> [rnayak: modify to use upstream tile support sort and squash some functions] Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20190806060536.18094-2-rnayak@codeaurora.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-13Merge tag 'pinctrl-v5.3-1' of ↵Linus Torvalds1-1/+10
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.3 kernel cycle: Core changes: - Device links can optionally be added between a pin control producer and its consumers. This will affect how the system power management is handled: a pin controller will not suspend before all of its consumers have been suspended. This was necessary for the ST Microelectronics STMFX expander and need to be tested on other systems as well: it makes sense to make this default in the long run. Right now it is opt-in per driver. - Drive strength can be specified in microamps. With decreases in silicon technology, milliamps isn't granular enough, let's make it possible to select drive strengths in microamps. Right now the Meson (AMlogic) driver needs this. New drivers: - New subdriver for the Tegra 194 SoC. - New subdriver for the Qualcomm SDM845. - New subdriver for the Qualcomm SM8150. - New subdriver for the Freescale i.MX8MN (Freescale is now a product line of NXP). - New subdriver for Marvell MV98DX1135. Driver improvements: - The Bitmain BM1880 driver now supports pin config in addition to muxing. - The Qualcomm drivers can now reserve some GPIOs as taken aside and not usable for users. This is used in ACPI systems to take out some GPIO lines used by the BIOS so that noone else (neither kernel nor userspace) will play with them by mistake and crash the machine. - A slew of refurbishing around the Aspeed drivers (board management controllers for servers) in preparation for the new Aspeed AST2600 SoC. - A slew of improvements over the SH PFC drivers as usual. - Misc cleanups and fixes" * tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits) pinctrl: aspeed: Strip moved macros and structs from private header pinctrl: aspeed: Fix missed include pinctrl: baytrail: Use GENMASK() consistently pinctrl: baytrail: Re-use data structures from pinctrl-intel.h pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux() pinctrl: qcom: Add SM8150 pinctrl driver dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding dt-bindings: pinctrl: qcom: Document missing gpio nodes pinctrl: aspeed: Add implementation-related documentation pinctrl: aspeed: Split out pinmux from general pinctrl pinctrl: aspeed: Clarify comment about strapping W1C pinctrl: aspeed: Correct comment that is no longer true MAINTAINERS: Add entry for ASPEED pinctrl drivers dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema dt-bindings: pinctrl: aspeed: Split bindings document in two pinctrl: qcom: Add irq_enable callback for msm gpio pinctrl: madera: Fixup SPDX headers pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard pinctrl: tegra: Add bitmask support for parked bits ...
2019-07-04pinctrl: qcom: Add SM8150 pinctrl driverPrasad Sodagudi1-0/+9
Add initial pinctrl driver to support pin configuration with pinctrl framework for SM8150 Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org> [vkoul: modify to use upstream tile support use upstream code style order the functions and squash functions] Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20190702105045.27646-4-vkoul@kernel.org Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-28 10:28:26 +0000