| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently almost each platform driver uses its own resets and clocks
naming in order to get the corresponding descriptors. It makes the code
harder to maintain and comprehend especially seeing the DWC PCIe core main
resets and clocks signals set hasn't changed much for about at least one
major IP-core release. So in order to organize things around these signals
we suggest to create a generic interface for them in accordance with the
naming introduced in the DWC PCIe IP-core reference manual:
Application clocks:
- "dbi" - data bus interface clock (on some DWC PCIe platforms it's
referred as "pclk", "pcie", "sys", "ahb", "cfg", "iface",
"gio", "reg", "pcie_apb_sys");
- "mstr" - AXI-bus master interface clock (some DWC PCIe glue drivers
refer to this clock as "port", "bus", "pcie_bus",
"bus_master/master_bus/axi_m", "pcie_aclk");
- "slv" - AXI-bus slave interface clock (also called as "port", "bus",
"pcie_bus", "bus_slave/slave_bus/axi_s", "pcie_aclk",
"pcie_inbound_axi").
Core clocks:
- "pipe" - core-PCS PIPE interface clock coming from external PHY (it's
normally named by the platform drivers as just "pipe");
- "core" - primary clock of the controller (none of the platform drivers
declare such a clock but in accordance with the ref. manual
the devices may have it separately specified);
- "aux" - auxiliary PMC domain clock (it is named by some platforms as
"pcie_aux" and just "aux");
- "ref" - Generic reference clock (it is a generic clock source, which
can be used as a signal source for multiple interfaces, some
platforms call it as "ref", "general", "pcie_phy",
"pcie_phy_ref").
Application resets:
- "dbi" - Data-bus interface reset (it's CSR interface clock and is
normally called as "apb" though technically it's not APB but
DWC PCIe-specific interface);
- "mstr" - AXI-bus master reset (some platforms call it as "port", "apps",
"bus", "axi_m");
- "slv" - ABI-bus slave reset (some platforms call it as "port", "apps",
"bus", "axi_s").
Core resets:
- "non-sticky" - non-sticky CSR flags reset;
- "sticky" - sticky CSR flags reset;
- "pipe" - PIPE-interface (Core-PCS) logic reset (some platforms
call it just "pipe");
- "core" - controller primary reset (resets everything except PMC
module, some platforms refer to this signal as "soft",
"pci");
- "phy" - PCS/PHY block reset (strictly speaking it is normally
connected to the input of an external block, but the
reference manual says it must be available for the PMC
working correctly, some existing platforms call it
"pciephy", "phy", "link");
- "hot" - PMC hot reset signal (also called as "sleep");
- "pwr" - cold reset signal (can be referred as "pwr", "turnoff").
Bus reset:
- "perst" - PCIe standard signal used to reset the PCIe peripheral
devices.
As you can see each platform uses it's own naming for basically the same
set of the signals. In the framework of this commit we suggest to add a
set of the clocks and reset signals resources, corresponding names and
identifiers for each denoted entity. At current stage the platforms will
be able to use the provided infrastructure to automatically request all
these resources and manipulate with them in the Host/EP init callbacks.
Alas it isn't that easy to create a common cold/hot reset procedure due to
too many platform-specifics in the procedure, like the external flags
exposure and the delays requirement.
Link: https://lore.kernel.org/r/20221113191301.5526-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Since the iATU CSR region is now retrieved in the DW PCIe resources getter
there is no much benefits in the iATU detection procedures splitting up.
Therefore let's join the iATU unroll/viewport detection procedure with the
rest of the iATU parameters detection code. The resultant method will be
as coherent as before, while the redundant functions will be eliminated
thus producing more readable code.
Link: https://lore.kernel.org/r/20221113191301.5526-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Currently the DW PCIe Root Port and Endpoint CSR spaces are retrieved in
the separate parts of the DW PCIe core driver. It doesn't really make
sense since the both controller types have identical set of the core CSR
regions: DBI, DBI CS2 and iATU/eDMA. Thus we can simplify the DW PCIe Host
and EP initialization methods by moving the platform-specific registers
space getting and mapping into a common method. It gets to be even more
justified seeing the CSRs base address pointers are preserved in the
common DW PCIe descriptor. Note all the OF-based common DW PCIe settings
initialization will be moved to the new method too in order to have a
single function for all the generic platform properties handling in single
place.
A nice side-effect of this change is that the pcie-designware-host.c and
pcie-designware-ep.c drivers are cleaned up from all the direct dw_pcie
storage modification, which makes the DW PCIe core, Root Port and Endpoint
modules more coherent.
Link: https://lore.kernel.org/r/20221113191301.5526-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Since in addition to the already available iATU unrolled mapping we are
about to add a few more DW PCIe platform-specific capabilities (CDM-check
and generic clocks/resets resources) let's add a generic interface to set
and get the flags indicating their availability. The new interface shall
improve maintainability of the platform-specific code.
Link: https://lore.kernel.org/r/20221113191301.5526-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In accordance with the generic PCIe Root Port DT-bindings the "dma-ranges"
property has the same format as the "ranges" property. The only difference
is in their semantics. The "dma-ranges" property describes the PCIe-to-CPU
memory mapping in opposite to the CPU-to-PCIe mapping of the "ranges"
property. Even though the DW PCIe controllers are normally equipped with
the internal Address Translation Unit which inbound and outbound tables
can be used to implement both properties semantics, it was surprising for
me to discover that the host-related part of the DW PCIe driver currently
supports the "ranges" property only while the "dma-ranges" windows are
just ignored. Having the "dma-ranges" supported in the driver would be
very handy for the platforms, that don't tolerate the 1:1 CPU-PCIe memory
mapping and require a customized PCIe memory layout. So let's fix that by
introducing the "dma-ranges" property support.
First of all we suggest to rename the dw_pcie_prog_inbound_atu() method to
dw_pcie_prog_ep_inbound_atu() and create a new version of the
dw_pcie_prog_inbound_atu() function. Thus we'll have two methods for the
RC and EP controllers respectively in the same way as it has been
developed for the outbound ATU setup methods.
Secondly aside with the memory window index and type the new
dw_pcie_prog_inbound_atu() function will accept CPU address, PCIe address
and size as its arguments. These parameters define the PCIe and CPU memory
ranges which will be used to setup the respective inbound ATU mapping. The
passed parameters need to be verified against the ATU ranges constraints
in the same way as it is done for the outbound ranges.
Finally the DMA-ranges detected for the PCIe controller need to be
converted to the inbound ATU entries during the host controller
initialization procedure. It will be done in the framework of the
dw_pcie_iatu_setup() method. Note before setting the inbound ranges up we
need to disable all the inbound ATU entries in order to prevent unexpected
PCIe TLPs translations defined by some third party software like
bootloaders.
Link: https://lore.kernel.org/r/20221113191301.5526-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
commit aeaa0bfe89654 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe8965 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
|
|
Make __dw_pcie_prog_outbound_atu() check the requested region base and size
against what the hardware can support. Return error if the region is not
correctly aligned or of a supported size.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The DWC PCIe RC/EP/DM IP core configuration parameters determine the number
of inbound and outbound iATU windows, alignment requirements (which is also
the minimum window size), minimum and maximum sizes. If internal ATU is
enabled, the former settings are determined by CX_ATU_MIN_REGION_SIZE; the
latter are determined by CX_ATU_MAX_REGION_SIZE.
Determine the required alignment and maximum size supported by the
controller and log it to help verify whether the requested inbound or
outbound memory mappings can be fully created.
Note 1. The extended iATU regions have been supported since DWC PCIe
v4.60a. There is no need in testing the upper limit register availability
for the older cores.
Note 2. The regions alignment is determined with using the fls() method
since the lower four bits of the ATU Limit register can be occupied with
the Circular Buffer Increment setting, which can be initialized with zeros.
Link: https://lore.kernel.org/r/20220624143947.8991-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Previously __dw_pcie_prog_outbound_atu() duplicated a lot of code between
the iatu_unroll_enabled version and the PCIE_ATU_VIEWPORT version:
__dw_pcie_prog_outbound_atu
if (iatu_unroll_enabled)
dw_pcie_prog_outbound_atu_unroll
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_LOWER_BASE, ...)
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_UPPER_BASE, ...)
...
return
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
dw_pcie_writel_dbi(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_dbi(PCIE_ATU_UPPER_BASE, ...)
...
Unify those by pushing the unroll address computation and viewport
selection down into dw_pcie_writel_atu() so we can use the same
dw_pcie_writel_atu_ob() accessor for both paths:
__dw_pcie_prog_outbound_atu
dw_pcie_writel_atu_ob(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_atu
dw_pcie_select_atu # new
if (iatu_unroll_enabled)
return pci->atu_base + PCIE_ATU_UNROLL_BASE(...)
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
return pci->atu_base
dw_pcie_write(base + reg)
dw_pcie_writel_atu_ob(PCIE_ATU_UPPER_BASE, ...)
...
In the non-unroll case, this does involve more MMIO writes to
PCIE_ATU_VIEWPORT, but it's mainly in initialization paths and the code
simplification is significant.
[bhelgaas: commit log, simplify dw_pcie_select_atu()]
Link: https://lore.kernel.org/r/20220624143947.8991-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously callers of dw_pcie_disable_atu() supplied enum
dw_pcie_region_type (DW_PCIE_REGION_INBOUND, DW_PCIE_REGION_OUTBOUND),
which dw_pcie_disable_atu() converted to the PCIE_ATU_REGION_DIR_IB or
PCIE_ATU_REGION_DIR_OB values needed to program the ATU registers.
Simplify the code by dropping the dw_pcie_region_type enum and passing
PCIE_ATU_REGION_DIR_IB or PCIE_ATU_REGION_DIR_OB directly.
Reorder dw_pcie_disable_atu() arguments to (dir, index) since "index"
indicates an ATU window in the regions of the corresponding direction.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Previously dw_pcie_ep_set_bar() converted the BAR PCI_BASE_ADDRESS_SPACE
bit to the internal dw_pcie_as_type enum (DW_PCIE_AS_MEM, DW_PCIE_AS_IO)
and passed it down to dw_pcie_prog_inbound_atu(), which converted the enum
to the PCIE_ATU_TYPE_MEM/PCIE_ATU_TYPE_IO values needed to program the ATU
registers.
Simplify the code by dropping the dw_pcie_as_type enum and passing
PCIE_ATU_TYPE_MEM or PCIE_ATU_TYPE_IO directly.
Reorder inbound ATU function arguments to match the outbound functions,
with address-related parameters at the end.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add macros to compare DWC IP core versions:
dw_pcie_ver_is()
dw_pcie_ver_is_ge()
dw_pcie_ver_type_is()
dw_pcie_ver_type_is_ge()
These are along the lines of DWC3_VER_IS() and dw_spi_ver_is().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Since DWC PCIe v4.70a, the controller version and version type can be read
from the PORT_LOGIC.PCIE_VERSION_OFF and PORT_LOGIC.PCIE_VERSION_TYPE_OFF
registers respectively.
Read the version from those registers and warn if if's different from the
version we got from the device tree.
We can only read the version after platform-specific drivers have done any
DBI-related initialization, such as reference clock activation.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Save the DWC IP core version in the same format as the
PORT_LOGIC.PCIE_VERSION_OFF register, similar to what other drivers for DWC
IP do (dw_spi_hw_init(), dwc3_core_is_valid(), stmmac_hwif_init()).
[bhelgaas: trim commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Printing just "link up" isn't very informative for PCI Express. Even if the
link is up, bus performance can degrade to slower speeds or to narrower
width than both Root Port and its partner is capable of. In that case it
would be handy to know the link specifications as early as possible.
If the link comes up, log the link speed (PCIe generation) and width.
Link: https://lore.kernel.org/r/20220624143947.8991-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There are several places in the common DW PCIe code with incoherent local
variable usage: a variable is defined and initialized with a structure
field, but the structure pointer is dereferenced to access that field
anyway; the local variable is defined and initialized but either used just
once or not used afterwards in the main part of the subsequent method. It
mainly concerns the pcie_port.dev field. Fix that in the relevant places.
Link: https://lore.kernel.org/r/20220624143428.8334-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
While the rest of the generic DWC PCIe code uses the dedicated IO-mem
accessors, the dw_pcie_link_up() method for some unobvious reason directly
calls readl() to get PortLogic.DEBUG1 register content. Since the way the
DBI bus is accessed can be platform-specific, use dw_pcie_readl_dbi()
instead so dw_pcie_link_up() is slightly more generic.
Link: https://lore.kernel.org/r/20220624143428.8334-11-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
The unrolled version of the internal ATU has been available since the DWC
PCIe v4.80a IP core, but it may not be enabled. Per [1], if unrolled ATU
is enabled, the PCIE_ATU_VIEWPORT does not exist and reads as 0xffffffff;
while if unrolled ATU is disabled, PCIE_ATU_VIEWPORT will contain some
zeros.
Simplify dw_pcie_iatu_unroll_enabled() by checking the value of
PCIE_ATU_VIEWPORT.
[1] DesignWare Cores, PCI Express Controller, Register Desciptions,
v.4.90a, December 2016, p.855
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-10-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Add newlines to log messages that are missing them.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-9-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Add braces around single-line if-else statements when the opposite case
requires them.
Link: https://lore.kernel.org/r/20220624143428.8334-8-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def73e ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f65324 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f65324 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
dw_pcie_disable_atu() was introduced by f8aed6ec624f ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
On imx6 and perhaps others when pcie probes you get a:
imx6q-pcie 33800000.pcie: invalid resource
This occurs because the atu is not specified in the DT and as such it
should not be remapped.
Link: https://lore.kernel.org/r/20211101180243.23761-1-tharvey@gateworks.com
Fixes: 281f1f99cf3a ("PCI: dwc: Detect number of iATU windows")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
|
|
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf3a
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf3a ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The size parameter is unsigned long type which can accept size > 4GB. In
that case, the upper limit address must be programmed. Add support to
program the upper limit address and set INCREASE_REGION_SIZE in case size >
4GB.
Link: https://lore.kernel.org/r/1612250918-19610-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Since outbound iATU permits size to be greater than 4GB for which the
support is also available, allow EP function to send u64 size instead of
truncating to u32.
Link: https://lore.kernel.org/r/1609929900-19082-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
|
|
DesignWare core has a TLP digest (TD) override bit in one of the control
registers of ATU. This bit also needs to be programmed for proper ECRC
functionality. This is currently identified as an issue with DesignWare
IP version 4.90a.
[bhelgaas: fix typos/grammar errors]
Link: https://lore.kernel.org/r/20201230165723.673-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Currently the number of inbound and outbound iATU windows are determined
from DT properties. Unfortunately, there's 'num-viewport' for RC mode
and 'num-ib-windows' and 'num-ob-windows' for EP mode, yet the number of
windows is not mode dependent. Also, 'num-viewport' is not clear whether
that's inbound, outbound or both. We can probably assume it's outbound
windows as that's all RC mode uses.
However, using DT properties isn't really needed as the number of
regions can be detected at runtime by poking the iATU registers. The
basic algorithm is just writing a target address and reading back what
we wrote. In the unrolled ATU case, we have to take care not to go
past the mapped region.
With this, we can drop num_viewport in favor of num_ob_windows instead.
Link: https://lore.kernel.org/r/20201105211159.1814485-17-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
|
|
Add support to program the ATU to enable translations for >4GB sizes of
the prefetchable memory apertures.
Link: https://lore.kernel.org/r/20201118144626.32189-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo <jingoohan1@gmail.com>
|
|
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
Fixes warning given by executing "make C=2 drivers/pci/"
Sparse output:
CHECK drivers/pci/controller/dwc/pcie-designware.c
drivers/pci/controller/dwc/pcie-designware.c:432:52: warning:
cast truncates bits from constant value (ffffffff7fffffff becomes
7fffffff)
Link: https://lore.kernel.org/r/7ea7f7d342f97c758949a17b870012f52ce5b3f5.1600767645.git.gustavo.pimentel@synopsys.com
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
|
|
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
|
|
The Intel driver is the only one to set PORT_LINK_DLL_LINK_EN. The
default value is set and it seems pretty certain that enabling link
initialization is always required. Maybe it could just be dropped from
the Intel driver, but lets move setting it into the common code to be
sure.
Link: https://lore.kernel.org/r/20200821035420.380495-36-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
|
|
keystone would force gen2 if no DT property. Now it relies on the
PCI_EXP_LNKCAP value.
Link: https://lore.kernel.org/r/20200821035420.380495-35-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
|
|
The ATU registers are only accessed in pcie-designware.c and can be private
to it.
Link: https://lore.kernel.org/r/20200821035420.380495-34-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
|
|
The DBI2 appears to be write-only and there's no read accesses in the code
anyways, so let's remove all the read_dbi2 related code.
Link: https://lore.kernel.org/r/20200821035420.380495-33-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
"Fast Link Mode" is a simulation environment speed up setting which should
never be set and the default is not set. However some Amlogic platforms
have it set (by firmware presumably). See commit 87dccf09323f ("PCI:
amlogic: meson: Don't use FAST_LINK_MODE to set up link") for more
information. Let's clear it in core DWC code so we can drop some vendor
specific code.
Link: https://lore.kernel.org/r/20200821035420.380495-25-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a 'num_lanes' field to allow drivers to provide a the number of lanes
if not in DT or using a custom DT property. A driver can provide a
non-zero value which is used if the DT doesn't have a 'num-lanes'
property.
Link: https://lore.kernel.org/r/20200821035420.380495-24-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
|
|
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Function dw_pcie_prog_outbound_atu_unroll() does not program the upper
32-bit ATU limit register. Since ATU programming functions limit the
size of the translated region to 4GB by using a u32 size parameter,
these issues may combine into undefined behavior for resource sizes
with non-zero upper 32-bits.
For example, a 128GB address space starting at physical CPU address of
0x2000000000 with size of 0x2000000000 needs the following values
programmed into the lower and upper 32-bit limit registers:
0x3fffffff in the upper 32-bit limit register
0xffffffff in the lower 32-bit limit register
Currently, only the lower 32-bit limit register is programmed with a
value of 0xffffffff but the upper 32-bit limit register is not being
programmed. As a result, the upper 32-bit limit register remains at its
default value after reset of 0x0.
These issues may combine to produce undefined behavior since the ATU
limit address may be lower than the ATU base address. Programming the
upper ATU limit address register prevents such undefined behavior despite
the region size getting truncated due to the 32-bit size limit.
Link: https://lore.kernel.org/r/1585785493-23210-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
Add support to PCIe RC controller on Intel Gateway SoCs.
PCIe controller is based of Synopsys DesignWare PCIe core.
Intel PCIe driver requires Upconfigure support, Fast Training
Sequence and link speed configurations. So adding the respective
helper functions in the PCIe DesignWare framework.
It also programs hardware autonomous speed during speed
configuration so defining it in pci_regs.h.
Also, mark Intel PCIe driver depends on MSI IRQ Domain
as Synopsys DesignWare framework depends on the
PCI_MSI_IRQ_DOMAIN.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
|
|
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
The num-lanes is optional since it is not needed on some platforms
that bring up the link in firmware.
The link programming is based on the num-lanes properties (which is
optional); if it is not present code must return instead of fiddling
with the lanes value to print an error message.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
Add support to enable CDM (Configuration Dependent Module) register
check for any data corruption based on the DT property
'snps,enable-cdm-check'.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
