| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2022-07-27 | PCI: Convert to new *_PM_OPS macros | Bjorn Helgaas | 1 | -4/+2 | |
| Replace SET_*_PM_OPS with *_PM_OPS, which which have the advantage that the compiler always sees the PM callbacks as referenced, so they don't need to be wrapped with "#ifdef CONFIG_PM_SLEEP" or tagged with "__maybe_unused" to avoid "defined but not used" warnings. See 1a3c7bb08826 ("PM: core: Add new *_PM_OPS macros, deprecate old ones"). Link: https://lore.kernel.org/r/20220719215108.1583108-1-helgaas@kernel.org Tested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pali Rohár <pali@kernel.org> # pci-mvebu.c Reviewed-by: Arnd Bergmann <arnd@arndb.de> | |||||
| 2021-08-19 | PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state | Nadeem Athani | 1 | -0/+16 | |
| PCIe fails to link up if SERDES lanes not used by PCIe are assigned to another protocol. For example, link training fails if lanes 2 and 3 are assigned to another protocol while lanes 0 and 1 are used for PCIe to form a two lane link. This failure is due to an incorrect tie-off on an internal status signal indicating electrical idle. Status signals going from SERDES to PCIe Controller are tied-off when a lane is not assigned to PCIe. Signal indicating electrical idle is incorrectly tied-off to a state that indicates non-idle. As a result, PCIe sees unused lanes to be out of electrical idle and this causes LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to occur. If a receiver is not detected on the first receiver detection attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and again moves forward to Detect.Active state without waiting for 12ms as required by PCIe base specification. Since wait time in Detect.Quiet is skipped, multiple receiver detect operations are performed back-to-back without allowing time for capacitance on the transmit lines to discharge. This causes subsequent receiver detection to always fail even if a receiver gets connected eventually. Add a quirk flag "quirk_detect_quiet_flag" to program the minimum time the LTSSM should wait on entering Detect.Quiet state here. This has to be set for J7200 as it has an incorrect tie-off on unused lanes. Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com Signed-off-by: Nadeem Athani <nadeem@cadence.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> | |||||
| 2020-08-05 | Merge branch 'pci/host-probe-refactor' | Bjorn Helgaas | 1 | -4/+5 | |
| - Use pci_host_bridge.windows list directly instead of splicing in a temporary list for cadence, mvebu, host-common (Rob Herring) - Use pci_host_probe() instead of open-coding all the pieces for altera, brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene, xilinx, xilinx-nwl (Rob Herring) - Convert to devm_platform_ioremap_resource_byname() instead of open-coding platform_get_resource_byname() and devm_ioremap_resource() for altera, cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng) - Convert to devm_platform_ioremap_resource() instead of open-coding platform_get_resource() and devm_ioremap_resource() for aardvark, brcmstb, exynos, ftpci100, versatile (Dejin Zheng) - Remove redundant error messages from devm_pci_remap_cfg_resource() callers (Dejin Zheng) - Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring) - Default host bridge parent device to the platform device (Rob Herring) - Drop unnecessary zeroing of host bridge fields (Rob Herring) - Use pci_is_root_bus() instead of tracking root bus number separately in aardvark, designware (imx6, keystone, designware-host), mobiveil, xilinx-nwl, xilinx, rockchip, rcar (Rob Herring) - Set host bridge bus number in pci_scan_root_bus_bridge() instead of each driver for aardvark, designware-host, host-common, mediatek, rcar, tegra, v3-semi (Rob Herring) - Use bridge resources instead of parsing DT 'ranges' again for cadence (Rob Herring) - Remove private bus number and range from cadence (Rob Herring) - Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring) - Use struct pci_host_bridge.windows list directly rather than a temporary (Rob Herring) - Reduce OF "missing non-prefetchable window" from error to warning message (Rob Herring) - Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new arch-independent interfaces (Rob Herring) - Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring) - Set bridge map_irq and swizzle_irq to default functions; drivers that don't support legacy IRQs (iproc) need to undo this (Rob Herring) * pci/host-probe-refactor: PCI: Set bridge map_irq and swizzle_irq to default functions PCI: Move DT resource setup into devm_pci_alloc_host_bridge() PCI: rcar-gen2: Convert to use modern host bridge probe functions PCI: of: Reduce missing non-prefetchable memory region to a warning PCI: rcar: Use struct pci_host_bridge.windows list directly PCI: rcar: Use devm_pci_alloc_host_bridge() PCI: cadence: Remove private bus number and range storage PCI: cadence: Use bridge resources for outbound window setup PCI: Move setting pci_host_bridge.busnr out of host drivers PCI: rcar: Use pci_is_root_bus() to check if bus is root bus PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus PCI: designware: Use pci_is_root_bus() to check if bus is root bus PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus PCI: Drop unnecessary zeroing of bridge fields PCI: Set default bridge parent device PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS PCI: controller: Remove duplicate error message PCI: controller: Convert to devm_platform_ioremap_resource() PCI: controller: Convert to devm_platform_ioremap_resource_byname() PCI: xilinx: Use pci_host_probe() to register host PCI: xilinx-nwl: Use pci_host_probe() to register host PCI: rockchip: Use pci_host_probe() to register host PCI: rcar: Use pci_host_probe() to register host PCI: iproc: Use pci_host_probe() to register host PCI: altera: Use pci_host_probe() to register host PCI: xgene: Use pci_host_probe() to register host PCI: versatile: Use pci_host_probe() to register host PCI: v3: Use pci_host_probe() to register host PCI: tegra: Use pci_host_probe() to register host PCI: mobiveil: Use pci_host_probe() to register host PCI: brcmstb: Use pci_host_probe() to register host PCI: host-common: Use struct pci_host_bridge.windows list directly PCI: mvebu: Use struct pci_host_bridge.windows list directly PCI: cadence: Use struct pci_host_bridge.windows list directly # Conflicts: # drivers/pci/controller/cadence/pcie-cadence-host.c | |||||
| 2020-07-27 | PCI: cadence: Add new *ops* for CPU addr fixup | Kishon Vijay Abraham I | 1 | -2/+6 | |
| Cadence driver uses "mem" memory resource to obtain the offset of configuration space address region, memory space address region and message space address region. The obtained offset is used to program the Address Translation Unit (ATU). However certain platforms like TI's J721E SoC require the absolute address to be programmed in the ATU and not just the offset. Add new *ops* for CPU addr fixup for the platform drivers to provide the correct address to be programmed in the ATU. Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> | |||||
| 2020-07-23 | PCI: cadence: Remove private bus number and range storage | Rob Herring | 1 | -4/+5 | |
| There's no need to store the bus number or range resource as the driver only needs the bus number which is already in the pci_host_bridge. For endpoint mode, the bus number is always 0. Link: https://lore.kernel.org/r/20200722022514.1283916-14-robh@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Tom Joseph <tjoseph@cadence.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> | |||||
| 2019-11-11 | PCI: cadence: Move all files to per-device cadence directory | Tom Joseph | 1 | -0/+253 | |
| Cadence core library files may be used by various platform drivers. Add a new directory "cadence" to group all the Cadence core library files and the platforms using Cadence core library. Signed-off-by: Tom Joseph <tjoseph@cadence.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> | |||||
 |
index : linux | |
| Linux Kernel (branches are rebased on master from time to time) | Linus Torvalds |
| summaryrefslogtreecommitdiffstats |