| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ksz8795 and ksz9477 uses the same algorithm for the
port_stp_state_set function except the register address is different. So
moved the algorithm to the ksz_common.c and used the dev_ops for
register read and write. This function can also used for the lan937x
part. Hence making it generic for all the parts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424112831.11504-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for Microchip KSZ series switch support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
