summaryrefslogtreecommitdiffstats
path: root/drivers/hwmon
AgeCommit message (Collapse)AuthorFilesLines
2022-12-13Merge tag 'hwmon-for-v6.2-rc1' of ↵Linus Torvalds35-403/+1451
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon updates from Guenter Roeck: "New drivers: - Driver for OneXPlayer mini AMD sensors - Ampere's Altra smpro-hwmon driver New chip and attribute support in existing drivers: - nct6775: Support for ASUS CROSSHAIR VIII/TUF/ProArt B550M - pmbus/ltc2978: Support for LTC7132 - aquacomputer_d5next: Support for temperature sensor offsets and flow sensor pulses - coretemp: Support for dynamic ttarget and tjmax Improvements: - Use devm_regulator_get_enable() where appropriate - Use sysfs_emit() instead of scnprintf() - Remove some useless #include <linux/hwmon-vid.h> - Include <linux/kstrtox.h> when appropriate - Use simple i2c probe - it87: Check for a valid chip before using force_id, and new new module parameter to ignore ACPI resource conflicts - jc42: Use regmap, and restore min/max/critical temperatures on resume - Add reporting power good and status to PMBus based regulators Last minute fixes: - emc2305: Fix probing of emc2301/2/3, and fix setting pwm values manually if THERMAL is enabled And various other minor fixes and improvements" * tag 'hwmon-for-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (37 commits) hwmon: (emc2305) fix pwm never being able to set lower hwmon: (emc2305) fix unable to probe emc2301/2/3 hwmon: (dell-smm) Move error message to make probing silent hwmon: use sysfs_emit() to instead of scnprintf() hwmon: (oxp-sensors) Fix pwm reading hwmon: (aquacomputer_d5next) Add support for Quadro flow sensor pulses hwmon: (pmbus/core) Implement regulator get_status hwmon: (oxp-sensors) Add AOK ZOE and Mini PRO hwmon: (gsc-hwmon) Switch to flexible array to simplify code hwmon: (pmbus) Add power good support hwmon: (nct6775) add ASUS CROSSHAIR VIII/TUF/ProArt B550M hwmon: (coretemp) Add support for dynamic ttarget hwmon: (coretemp) Add support for dynamic tjmax hwmon: (coretemp) rearrange tjmax handing code hwmon: Remove some useless #include <linux/hwmon-vid.h> hwmon: (coretemp) Remove obsolete temp_data->valid hwmon: add OneXPlayer mini AMD sensors driver hwmon: (aquacomputer_d5next) Clear up macros and comments hwmon: (it87) Add DMI table for future extensions hwmon: Include <linux/kstrtox.h> when appropriate ...
2022-12-12Merge branches 'acpi-scan', 'acpi-bus', 'acpi-tables' and 'acpi-sysfs'Rafael J. Wysocki2-7/+4
Merge ACPI changes related to device enumeration, device object managenet, operation region handling, table parsing and sysfs interface: - Use ZERO_PAGE(0) instead of empty_zero_page in the ACPI device enumeration code (Giulio Benetti). - Change the return type of the ACPI driver remove callback to void and update its users accordingly (Dawei Li). - Add general support for FFH address space type and implement the low- level part of it for ARM64 (Sudeep Holla). - Fix stale comments in the ACPI tables parsing code and make it print more messages related to MADT (Hanjun Guo, Huacai Chen). - Replace invocations of generic library functions with more kernel- specific counterparts in the ACPI sysfs interface (Christophe JAILLET, Xu Panda). * acpi-scan: ACPI: scan: substitute empty_zero_page with helper ZERO_PAGE(0) * acpi-bus: ACPI: FFH: Silence missing prototype warnings ACPI: make remove callback of ACPI driver void ACPI: bus: Fix the _OSC capability check for FFH OpRegion arm64: Add architecture specific ACPI FFH Opregion callbacks ACPI: Implement a generic FFH Opregion handler * acpi-tables: ACPI: tables: Fix the stale comments for acpi_locate_initial_tables() ACPI: tables: Print CORE_PIC information when MADT is parsed * acpi-sysfs: ACPI: sysfs: use sysfs_emit() to instead of scnprintf() ACPI: sysfs: Use kstrtobool() instead of strtobool()
2022-12-06hwmon: (emc2305) fix pwm never being able to set lowerXingjiang Qiao1-13/+24
There are fields 'last_hwmon_state' and 'last_thermal_state' in the structure 'emc2305_cdev_data', which respectively store the cooling state set by the 'hwmon' and 'thermal' subsystem, and the driver author hopes that if the state set by 'hwmon' is lower than the value set by 'thermal', the driver will just save it without actually setting the pwm. Currently, the 'last_thermal_state' also be updated by 'hwmon', which will cause the cooling state to never be set to a lower value. This patch fixes that. Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com> Link: https://lore.kernel.org/r/20221206055331.170459-2-nanpuyue@gmail.com Fixes: 0d8400c5a2ce1 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.") [groeck: renamed emc2305_set_cur_state_shim -> __emc2305_set_cur_state] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-06hwmon: (emc2305) fix unable to probe emc2301/2/3Xingjiang Qiao1-6/+1
The definitions of 'EMC2305_REG_PRODUCT_ID' and 'EMC2305_REG_DEVICE' are both '0xfd', they actually return the same value, but the values returned by emc2301/2/3/5 are different, so probe emc2301/2/3 will fail, This patch fixes that. Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com> Link: https://lore.kernel.org/r/20221206055331.170459-1-nanpuyue@gmail.com Fixes: 0d8400c5a2ce1 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (dell-smm) Move error message to make probing silentArmin Wolf1-1/+2
If dell-smm-hwmon loads on unsupported hardware like the Dell XPS 17 9710, an error message is printed. This might confuse users, as drivers are expected to be silent if no supported hardware is found. Reorder the error message so its only printed when the driver is loaded with the "force" option being set. Also reword the error message slightly. Tested on a Dell Inspiron 3505. Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20221130183418.357246-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: use sysfs_emit() to instead of scnprintf()ye xingchen3-10/+10
Replace the open-code with sysfs_emit() to simplify the code. Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn> Link: https://lore.kernel.org/r/202212011130317080061@zte.com.cn Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (oxp-sensors) Fix pwm readingJoaquín Ignacio Aramendía1-1/+1
PWM reading is only 1 register long. Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com> Link: https://lore.kernel.org/r/20221128185206.212022-1-samsagax@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (aquacomputer_d5next) Add support for Quadro flow sensor pulsesAleksa Savic1-13/+53
Add support for reading and writing flow sensor pulses value on the Aquacomputer Quadro. Implemented by Leonard Anderweit [1]. [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/45 Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20221126071313.34356-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (pmbus/core) Implement regulator get_statusPatrick Rudolph1-0/+44
Add get_status for pmbus_regulator_ops. Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com> Link: https://lore.kernel.org/r/20221124193642.4081054-1-Naresh.Solanki@9elements.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (oxp-sensors) Add AOK ZOE and Mini PROJoaquín Ignacio Aramendía1-6/+34
Add support for the AOK ZOE A1 and OXP Mini PRO handheld devices. DMI strings are added to this driver since the same EC layout is used and has similar specs as the OXP mini AMD. The added devices are: - OneXPlayer mini PRO (AMD 6800U) - AOK ZOE A1 (AMD 6800U) Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com> Link: https://lore.kernel.org/r/20221125114901.11309-1-samsagax@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (gsc-hwmon) Switch to flexible array to simplify codeChristophe JAILLET1-4/+2
Using flexible array is more straight forward. It - saves 1 pointer in the 'gsc_hwmon_platform_data' structure - saves an indirection when using this array - saves some LoC and avoids some always spurious pointer arithmetic Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/61a23e1d642397cfcecc4ac3bb0ab485d257987d.1668936855.git.christophe.jaillet@wanadoo.fr Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (pmbus) Add power good supportPatrick Rudolph1-2/+6
Update error flags with regulation out if regulator is on & power good status bit is set Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com> Link: https://lore.kernel.org/r/20221117184022.1808508-1-Naresh.Solanki@9elements.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (nct6775) add ASUS CROSSHAIR VIII/TUF/ProArt B550MDenis Pauk1-0/+7
Boards such as * ProArt B550-CREATOR * ProArt Z490-CREATOR 10G * ROG CROSSHAIR VIII EXTREME * ROG CROSSHAIR VIII HERO (WI-FI) * TUF GAMING B550M-E * TUF GAMING B550M-E (WI-FI) * TUF GAMING B550M-PLUS WIFI II have got a nct6775 chip, but by default there's no use of it because of resource conflict with WMI method. This commit adds such boards to the WMI monitoring list. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807 Signed-off-by: Denis Pauk <pauk.denis@gmail.com> Reported-by: yutesdb <mundanedefoliation@gmail.com> Tested-by: yutesdb <mundanedefoliation@gmail.com> Link: https://lore.kernel.org/r/20221114214456.3891-1-pauk.denis@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (coretemp) Add support for dynamic ttargetZhang Rui1-16/+41
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at runtime when the Intel SST-PP (Intel Speed Select Technology - Performance Profile) level is changed. As a result, the ttarget value also becomes dyamic. Improve the code to always get updated ttarget value. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Link: https://lore.kernel.org/r/20221113153145.32696-4-rui.zhang@intel.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (coretemp) Add support for dynamic tjmaxZhang Rui1-15/+31
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at runtime when the Intel SST-PP (Intel Speed Select Technology - Performance Profile) level is changed. Improve the code to always use updated tjmax when it can be retrieved from MSR_IA32_TEMPERATURE_TARGET. When tjmax can not be retrieved from MSR_IA32_TEMPERATURE_TARGET, still follow the previous logic and always use a static tjmax value. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Link: https://lore.kernel.org/r/20221113153145.32696-3-rui.zhang@intel.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (coretemp) rearrange tjmax handing codeZhang Rui1-78/+78
Rearrange the tjmax handling code so that it can be used directly in the sysfs attribute callbacks without forward declarations. No functional change in this patch. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Link: https://lore.kernel.org/r/20221113153145.32696-2-rui.zhang@intel.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: Remove some useless #include <linux/hwmon-vid.h>Christophe JAILLET2-2/+0
<linux/hwmon-vid.h> is not needed for these drivers. Remove the corresponding #include. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/41610f64a69bd0245ebc811fcff10ee54e93ac46.1668330765.git.christophe.jaillet@wanadoo.fr Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (coretemp) Remove obsolete temp_data->validZhang Rui1-4/+1
Checking for the valid bit of IA32_THERM_STATUS is removed in commit bf6ea084ebb5 ("hwmon: (coretemp) Do not return -EAGAIN for low temperatures"), and temp_data->valid is set and never cleared when the temperature has been read once. Remove the obsolete temp_data->valid field. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Link: https://lore.kernel.org/r/20221108075051.5139-2-rui.zhang@intel.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: add OneXPlayer mini AMD sensors driverJoaquín Ignacio Aramendía3-0/+268
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading and control via hwmon sysfs. As far as I could gather all OXP boards have the same DMI strings and they can be told appart only by the boot cpu vendor (Intel/AMD). Currently only AMD boards are supported since Intel have different EC registers and values to read/write. Fan control is provided via pwm interface in the range [0-255]. AMD boards have [0-100] as range in the EC, the written value is scaled to accommodate for that. Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com> Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com [groeck: Removed misleading comment about module_platform_driver()] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (aquacomputer_d5next) Clear up macros and commentsAleksa Savic1-34/+63
Reorganize macro definitions into sections for each supported device, with additional comments on their purpose. This should make it easier to follow what report each offset is coming from. Also, reformat per-device initializations in aqc_probe() to organize them into sections (fan info, temp sensors, other parameters and lastly labels). No functional changes. Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20221107142455.655998-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (it87) Add DMI table for future extensionsFrank Crawford1-19/+53
Add in DMI matching table to match various board quirks and settings. This will be useful for future extentions, but will start with the existing definition of the Shuttle SN68PT. Signed-off-by: Frank Crawford <frank@crawford.emu.id.au> Link: https://lore.kernel.org/r/20221105232531.1619387-1-frank@crawford.emu.id.au Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: Include <linux/kstrtox.h> when appropriateChristophe JAILLET7-0/+7
The kstrto<something>() functions have been moved from kernel.h to kstrtox.h. So, include the latter directly in the appropriate files. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/51688cf50bda44e2731381a31287c62319388783.1667763218.git.christophe.jaillet@wanadoo.fr Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (jc42) Consistently use bit and bitfield macros in the driverMartin Blumenstingl1-18/+18
Use BIT() and GENMASK() macros for defining the bitfields inside the registers. Also use FIELD_GET() and FIELD_PREP() where appropriate. This makes the coding style within the driver consistent. No functional changes intended. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (pmbus/ltc2978) add support for LTC7132Felix Nieuwenhuizen1-6/+11
Add support for LTC7132. The relevant registers in the LTC7132 are identical to the LTC7880. So it's just a matter of adding the chip id. Signed-off-by: Felix Nieuwenhuizen <Felix.Nieuwenhuizen@etas.com> Link: https://lore.kernel.org/r/20221027145135.31802-1-Felix.Nieuwenhuizen@etas.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (smpro-hwmon) Improve switch statments in smpro_is_visible()Nathan Chancellor1-1/+4
Clang warns: drivers/hwmon/smpro-hwmon.c:378:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough] default: ^ drivers/hwmon/smpro-hwmon.c:378:2: note: insert 'break;' to avoid fall-through default: ^ break; 1 error generated. Clang is a little more pedantic than GCC, which does not warn when falling through to a case that is just break or return. Clang's version is more in line with the kernel's own stance in deprecated.rst, which states that all switch/case blocks must end in either break, fallthrough, continue, goto, or return. Add the missing break to silence the warning. Additionally, adjust the indentation of a break and add a default case to the inner switch statement. Fixes: a87456864cbb ("hwmon: Add Ampere's Altra smpro-hwmon driver") Link: https://github.com/ClangBuiltLinux/linux/issues/1751 Signed-off-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20221027231611.3824800-1-nathan@kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (jc42) Fix missing unlock on error in jc42_write()Yang Yingliang1-1/+1
Add the missing unlock before return from function jc42_write() in the error handling case. Fixes: 37dedaee8bc6 ("hwmon: (jc42) Convert register access and caching to regmap/regcache") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20221027062931.598247-1-yangyingliang@huawei.com Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (jc42) Restore the min/max/critical temperatures on resumeMartin Blumenstingl1-1/+9
The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs (using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer 0x104a, device 0x2201). It does not keep the previously programmed minimum, maximum and critical temperatures after system suspend and resume (which is a shutdown / startup cycle for the JC42 temperature sensor). This results in an alarm on system resume because the hardware default for these values is 0°C (so any environment temperature greater than 0°C will trigger the alarm). Example before system suspend: jc42-i2c-0-1a Adapter: SMBus PIIX4 adapter port 0 at 0b00 temp1: +34.8°C (low = +0.0°C) (high = +85.0°C, hyst = +85.0°C) (crit = +95.0°C, hyst = +95.0°C) Example after system resume (without this change): jc42-i2c-0-1a Adapter: SMBus PIIX4 adapter port 0 at 0b00 temp1: +34.8°C (low = +0.0°C) ALARM (HIGH, CRIT) (high = +0.0°C, hyst = +0.0°C) (crit = +0.0°C, hyst = +0.0°C) Apply the cached values from the JC42_REG_TEMP_UPPER, JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where the SMBUS register is not related to this issue but a side-effect of using regcache_sync() during system resume with the previously cached/programmed values. This fixes the alarm due to the hardware defaults of 0°C because the previously applied limits (set by userspace) are re-applied on system resume. Fixes: 175c490c9e7f ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (jc42) Convert register access and caching to regmap/regcacheMartin Blumenstingl2-102/+132
Switch the jc42 driver to use an I2C regmap to access the registers. Also move over to regmap's built-in caching instead of adding a custom caching implementation. This works for JC42_REG_TEMP_UPPER, JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never change except when explicitly written. The cache For JC42_REG_TEMP is dropped (regmap can't cache it because it's volatile, meaning it can change at any time) as well for simplicity and consistency with other drivers. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (aquacomputer_d5next) Add support for temperature sensor offsetsAleksa Savic1-14/+74
Add support for reading and writing temperature sensor offsets on the Aquacomputer D5 Next, Farbwerk 360, Octo and Quadro, for which the needed offsets are known. Implemented by Leonard Anderweit [1]. [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/22 Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20221024151039.7222-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (occ) OCC sensors aren't arch-specificJeremy Kerr1-2/+0
Commit c112d75840fb ("hwmon: OCC drivers are ARM-only") made the OCC sensor drivers not selectable on powerpc64: These drivers are for a BMC inside PowerPC servers. The BMC runs on ARM hardware, so only propose the drivers on this architecture, unless build-testing. ... but we now have a powerpc64 BMC (still for a powerpc64 host), so drop the `depends on` that excludes building for this platform. Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Acked-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20221024081527.3842565-1-jk@codeconstruct.com.au Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: Add Ampere's Altra smpro-hwmon driverQuan Nguyen3-0/+472
This commit adds support for Ampere SMpro hwmon driver. This driver supports accessing various CPU sensors provided by the SMpro co-processor including temperature, power, voltages, and current. Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com> Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (adm1177) simplify using devm_regulator_get_enable()Matti Vaittinen1-24/+3
Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(), add_action_or_reset(regulator_disable)' and use the devm_regulator_get_enable() and drop the pointer to the regulator. This simplifies code and makes it less tempting to add manual control for the regulator which is also controlled by devm. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/7773541795f280db31dd981ffc21df8a630b794a.1666357434.git.mazziesaccount@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (lm90) simplify using devm_regulator_get_enable()Matti Vaittinen1-18/+2
Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(), add_action_or_reset(regulator_disable)' and use the devm_regulator_get_enable(). Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/a1fa4364cbb775de25478117dd22dda0742089e3.1666357434.git.mazziesaccount@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: use simple i2c probeStephen Kitt7-19/+14
All these drivers have an i2c probe function which doesn't use the "struct i2c_device_id *id" parameter, so they can trivially be converted to the "probe_new" style of probe with a single argument. This is part of an ongoing transition to single-argument i2c probe functions. Old-style probe functions involve a call to i2c_match_id: in drivers/i2c/i2c-core-base.c, /* * When there are no more users of probe(), * rename probe_new to probe. */ if (driver->probe_new) status = driver->probe_new(client); else if (driver->probe) status = driver->probe(client, i2c_match_id(driver->id_table, client)); else status = -EINVAL; Drivers which don't need the second parameter can be declared using probe_new instead, avoiding the call to i2c_match_id. Drivers which do can still be converted to probe_new-style, calling i2c_match_id themselves (as is done currently for of_match_id). This change was done using the following Coccinelle script, and fixed up for whitespace changes: @ rule1 @ identifier fn; identifier client, id; @@ - static int fn(struct i2c_client *client, const struct i2c_device_id *id) + static int fn(struct i2c_client *client) { ...when != id } @ rule2 depends on rule1 @ identifier rule1.fn; identifier driver; @@ struct i2c_driver driver = { - .probe + .probe_new = ( fn | - &fn + fn ) , }; Signed-off-by: Stephen Kitt <steve@sk2.org> Link: https://lore.kernel.org/r/20221011143309.3141267-1-steve@sk2.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (it87) Check for a valid chip before using force_idAhmad Khalifa1-1/+7
Check there is a chip before using force_id parameter as there is no value in registering a non-existent chip Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws> Link: https://lore.kernel.org/r/20221004210100.540120-3-ahmad@khalifa.ws Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (it87) Add param to ignore ACPI resource conflictsAhmad Khalifa1-2/+8
Add parameter to ignore ACPI resource conflicts as an alternate to using 'acpi_enforce_resources=lax'. Some BIOSes reserve resources and don't use them and the system wide parameter may result in failures to certain drivers. Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws> Link: https://lore.kernel.org/r/20221004210100.540120-2-ahmad@khalifa.ws Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-04hwmon: (fschmd) Make const arrays static constColin Ian King1-2/+2
Don't populate the read-only const arrays names and watchdog_minors on the stack but instead make them static const. Also makes the object code a little smaller. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20221005152752.318493-1-colin.i.king@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-01hwmon: (asus-ec-sensors) Add checks for devm_kcallocYuan Can1-0/+2
As the devm_kcalloc may return NULL, the return value needs to be checked to avoid NULL poineter dereference. Fixes: d0ddfd241e57 ("hwmon: (asus-ec-sensors) add driver for ASUS EC") Signed-off-by: Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221125014329.121560-1-yuancan@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-01hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new()Yang Yingliang1-1/+4
As comment of pci_get_domain_bus_and_slot() says, it returns a pci device with refcount increment, when finish using it, the caller must decrement the reference count by calling pci_dev_put(). So call it after using to avoid refcount leak. Fixes: 14513ee696a0 ("hwmon: (coretemp) Use PCI host bridge ID to identify CPU if necessary") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221118093303.214163-1-yangyingliang@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-12-01hwmon: (coretemp) Check for null before removing sysfs attrsPhil Auld1-0/+4
If coretemp_add_core() gets an error then pdata->core_data[indx] is already NULL and has been kfreed. Don't pass that to sysfs_remove_group() as that will crash in sysfs_remove_group(). [Shortened for readability] [91854.020159] sysfs: cannot create duplicate filename '/devices/platform/coretemp.0/hwmon/hwmon2/temp20_label' <cpu offline> [91855.126115] BUG: kernel NULL pointer dereference, address: 0000000000000188 [91855.165103] #PF: supervisor read access in kernel mode [91855.194506] #PF: error_code(0x0000) - not-present page [91855.224445] PGD 0 P4D 0 [91855.238508] Oops: 0000 [#1] PREEMPT SMP PTI ... [91855.342716] RIP: 0010:sysfs_remove_group+0xc/0x80 ... [91855.796571] Call Trace: [91855.810524] coretemp_cpu_offline+0x12b/0x1dd [coretemp] [91855.841738] ? coretemp_cpu_online+0x180/0x180 [coretemp] [91855.871107] cpuhp_invoke_callback+0x105/0x4b0 [91855.893432] cpuhp_thread_fun+0x8e/0x150 ... Fix this by checking for NULL first. Signed-off-by: Phil Auld <pauld@redhat.com> Cc: linux-hwmon@vger.kernel.org Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221117162313.3164803-1-pauld@redhat.com Fixes: 199e0de7f5df3 ("hwmon: (coretemp) Merge pkgtemp with coretemp") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-23ACPI: make remove callback of ACPI driver voidDawei Li2-7/+4
For bus-based driver, device removal is implemented as: 1 device_remove()-> 2 bus->remove()-> 3 driver->remove() Driver core needs no inform from callee(bus driver) about the result of remove callback. In that case, commit fc7a6209d571 ("bus: Make remove callback return void") forces bus_type::remove be void-returned. Now we have the situation that both 1 & 2 of calling chain are void-returned, so it does not make much sense for 3(driver->remove) to return non-void to its caller. So the basic idea behind this change is making remove() callback of any bus-based driver to be void-returned. This change, for itself, is for device drivers based on acpi-bus. Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Lee Jones <lee@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dawei Li <set_pte_at@outlook.com> Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for drivers/platform/surface/* Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2022-11-20hwmon: (ibmpex) Fix possible UAF when ibmpex_register_bmc() failsGaosheng Cui1-0/+1
Smatch report warning as follows: drivers/hwmon/ibmpex.c:509 ibmpex_register_bmc() warn: '&data->list' not removed from list If ibmpex_find_sensors() fails in ibmpex_register_bmc(), data will be freed, but data->list will not be removed from driver_data.bmc_data, then list traversal may cause UAF. Fix by removeing it from driver_data.bmc_data before free(). Fixes: 57c7c3a0fdea ("hwmon: IBM power meter driver") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221117034423.2935739-1-cuigaosheng1@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-20hwmon: (i5500_temp) fix missing pci_disable_device()Yang Yingliang1-1/+1
pci_disable_device() need be called while module exiting, switch to use pcim_enable(), pci_disable_device() will be called in pcim_release(). Fixes: ada072816be1 ("hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112125606.3751430-1-yangyingliang@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-20hwmon: (ina3221) Fix shunt sum critical calculationNinad Malwade1-2/+2
The shunt sum critical limit register value should be left shifted by one bit as its LSB-0 is a reserved bit. Fixes: 2057bdfb7184 ("hwmon: (ina3221) Add summation feature support") Signed-off-by: Ninad Malwade <nmalwade@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20221108044508.23463-1-nmalwade@nvidia.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-20hwmon: (ltc2947) fix temperature scalingDerek Nguyen1-1/+1
The LTC2947 datasheet (Rev. B) calls out in the section "Register Description: Non-Accumulated Result Registers" (pg. 30) that "To calculate temperature, multiply the TEMP register value by 0.204°C and add 5.5°C". Fix to add 5.5C and not 0.55C. Fixes: 9f90fd652bed ("hwmon: Add support for ltc2947") Signed-off-by: Derek Nguyen <derek.nguyen@collins.com> Signed-off-by: Brandon Maier <brandon.maier@collins.com> Link: https://lore.kernel.org/r/20221110192108.20624-1-brandon.maier@collins.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-04Revert "hwmon: (pmbus) Add regulator supply into macro"Guenter Roeck1-1/+0
This reverts commit 54cc3dbfc10dc3db7cb1cf49aee4477a8398fbde. Zev Weiss reports that the reverted patch may cause a regulator undercount. Here is his report: ... having regulator-dummy set as a supply on my PMBus regulators (instead of having them as their own top-level regulators without an upstream supply) leads to enable-count underflow errors when disabling them: # echo 0 > /sys/bus/platform/devices/efuse01/state [ 906.094477] regulator-dummy: Underflow of regulator enable count [ 906.100563] Failed to disable vout: -EINVAL [ 136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22 Zev reports that reverting the patch fixes the problem. So let's do that for now. Fixes: 54cc3dbfc10d ("hwmon: (pmbus) Add regulator supply into macro") Cc: Marcello Sylvester Bauer <sylv@sylv.io> Reported-by: Zev Weiss <zev@bewilderbeest.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-11-04hwmon: (scmi) Register explicitly with Thermal FrameworkCristian Marussi1-13/+103
Available sensors are enumerated and reported by the SCMI platform server using a 16bit identification number; not all such sensors are of a type supported by hwmon subsystem and, among the supported ones, only a subset could be temperature sensors that have to be registered with the Thermal Framework. Potential clashes between hwmon channels indexes and the underlying real sensors IDs do not play well with the hwmon<-->thermal bridge automatic registration routines and could need a sensible number of fake dummy sensors to be made up in order to keep indexes and IDs in sync. Avoid to use the hwmon<-->thermal bridge dropping the HWMON_C_REGISTER_TZ attribute and instead explicit register temperature sensors directly with the Thermal Framework. Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-hwmon@vger.kernel.org Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Link: https://lore.kernel.org/r/20221031114018.59048-1-cristian.marussi@arm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-10-23Merge tag 'x86_urgent_for_v6.0_rc2' of ↵Linus Torvalds1-15/+41
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Borislav Petkov: "As usually the case, right after a major release, the tip urgent branches accumulate a couple more fixes than normal. And here is the x86, a bit bigger, urgent pile. - Use the correct CPU capability clearing function on the error path in Intel perf LBR - A CFI fix to ftrace along with a simplification - Adjust handling of zero capacity bit mask for resctrl cache allocation on AMD - A fix to the AMD microcode loader to attempt patch application on every logical thread - A couple of topology fixes to handle CPUID leaf 0x1f enumeration info properly - Drop a -mabi=ms compiler option check as both compilers support it now anyway - A couple of fixes to how the initial, statically allocated FPU buffer state is setup and its interaction with dynamic states at runtime" * tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap() ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph() x86/ftrace: Remove ftrace_epilogue() x86/resctrl: Fix min_cbm_bits for AMD x86/microcode/AMD: Apply the patch early on every logical thread x86/topology: Fix duplicated core ID within a package x86/topology: Fix multiple packages shown on a single-package system hwmon/coretemp: Handle large core ID value x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB x86/fpu: Exclude dynamic states from init_fpstate x86/fpu: Fix the init_fpstate size check with the actual size x86/fpu: Configure init_fpstate attributes orderly
2022-10-22hwmon: (corsair-psu) Add USB id of the new HX1500i psuWilken Gottwalt1-0/+1
Also update the documentation accordingly. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net> Link: https://lore.kernel.org/r/Y0FghqQCHG/cX5Jz@monster.localdomain Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-10-17hwmon/coretemp: Handle large core ID valueZhang Rui1-15/+41
The coretemp driver supports up to a hard-coded limit of 128 cores. Today, the driver can not support a core with an ID above that limit. Yet, the encoding of core ID's is arbitrary (BIOS APIC-ID) and so they may be sparse and they may be large. Update the driver to map arbitrary core ID numbers into appropriate array indexes so that 128 cores can be supported, no matter the encoding of core ID's. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Len Brown <len.brown@intel.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20221014090147.1836-3-rui.zhang@intel.com
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-15 18:38:29 +0000