| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
|
|
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Acked-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
According to the description in ti-sn65dsi86's datasheet:
CHA_HSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
CHA_VSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (Default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
We should only set these bits when the polarity is negative.
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125104558.84616-1-eddy.zhang@rock-chips.com
|
|
Implement the bridge connector-related .get_edid() and .detect()
operations for full DP mode, and report the related bridge capabilities
and type.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-4-tomi.valkeinen@ideasonboard.com
|
|
Despite the SN65DSI86 being an eDP bridge, on some systems its output is
routed to a DisplayPort connector. Enable DisplayPort mode when the next
component in the display pipeline is detected as a DisplayPort
connector, and disable eDP features in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reworked to set bridge type based on the next bridge/connector.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
--
Changes since v1/RFC:
- Rebased on top of "drm/bridge: ti-sn65dsi86: switch to
devm_drm_of_get_bridge"
- eDP/DP mode determined from the next bridge connector type.
Changes since v2:
- Remove setting of Standard DP Scrambler Seed. (It's read-only).
- Prevent setting DP_EDP_CONFIGURATION_SET in
ti_sn_bridge_atomic_enable()
- Use Doug's suggested text for disabling ASSR on DP mode.
Changes since v3:
- Remove ASSR_CONTROL definition
Changes since v4:
- Refactor code to configure the DP/eDP scrambler in one place.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-3-tomi.valkeinen@ideasonboard.com
|
|
The front and back porch registers are 8 bits, and pulse width registers
are 15 bits, so reject any modes with larger periods.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-2-tomi.valkeinen@ideasonboard.com
|
|
If devm_drm_of_get_bridge() can't find the connected bridge, it returns an
ERR_PTR(-EPROBE_DEFER) to indicate that the probe should be deferred.
But this path also prints an error message, which pollutes the kernel log
since is printed on every probe deferral, i.e:
$ dmesg | grep "failed to create panel bridge" | wc -l
38
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220722074755.660258-1-javierm@redhat.com
|
|
Now as the driver does not depend on pdata->connector, add support for
attaching the bridge with DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220711092117.360797-3-dmitry.baryshkov@linaro.org
|
|
Rather than reading the pdata->connector directly, fetch the connector
using drm_atomic_state. This allows us to make pdata->connector optional
(and thus supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR).
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220711092117.360797-2-dmitry.baryshkov@linaro.org
|
|
Move away from the deprecated enable/disable operations in
drm_bridge_funcs and enable atomic use.
v3:
- Drop use of DRM_BRIDGE_STATE_OPS
v2:
- fix build (kernel test robot <lkp@intel.com>)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220703202724.9553-2-sam@ravnborg.org
|
|
Convert driver to use this new helper to standardize
OF "data-lanes" parsing.
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220524010522.528569-9-marex@denx.de
|
|
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
|
|
Let's start the 5.19 development cycle.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Pull drm updates from Dave Airlie:
"Lots of work all over, Intel improving DG2 support, amdkfd CRIU
support, msm new hw support, and faster fbdev support.
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device"
* tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm: (1529 commits)
drm/i915/display: Do not re-enable PSR after it was marked as not reliable
drm/i915/display: Fix HPD short pulse handling for eDP
drm/amdgpu: Use drm_mode_copy()
drm/radeon: Use drm_mode_copy()
drm/amdgpu: Use ternary operator in `vcn_v1_0_start()`
drm/amdgpu: Remove pointless on stack mode copies
drm/amd/pm: fix indenting in __smu_cmn_reg_print_error()
drm/amdgpu/dc: fix typos in comments
drm/amdgpu: fix typos in comments
drm/amd/pm: fix typos in comments
drm/amdgpu: Add stolen reserved memory for MI25 SRIOV.
drm/amdgpu: Merge get_reserved_allocation to get_vbios_allocations.
drm/amdkfd: evict svm bo worker handle error
drm/amdgpu/vcn: fix vcn ring test failure in igt reload test
drm/amdgpu: only allow secure submission on rings which support that
drm/amdgpu: fixed the warnings reported by kernel test robot
drm/amd/display: 3.2.177
drm/amd/display: [FW Promotion] Release 0.0.108.0
drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2
drm/amd/display: Wait for hubp read line for Pollock
...
|
|
The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".
Switch to the new function and reduce boilerplate.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183955.25508-1-jose.exposito89@gmail.com
|
|
The PM Runtime docs say:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We weren't doing that for autosuspend. Let's do it.
Fixes: 9bede63127c6 ("drm/bridge: ti-sn65dsi86: Use pm_runtime autosuspend")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222141838.1.If784ba19e875e8ded4ec4931601ce6d255845245@changeid
|
|
The ti-sn65dsi86 driver shouldn't hand-roll its own bridge
connector. It should use the normal drm_bridge_connector. Let's switch
to do that, removing all of the custom code.
NOTE: this still _doesn't_ implement DRM_BRIDGE_ATTACH_NO_CONNECTOR
support for ti-sn65dsi86 and that would still be a useful thing to do
in the future. It was attempted in the past [1] but put on the back
burner. However, unless we instantly change ti-sn65dsi86 fully from
not supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR at all to _only_
supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR then we'll still need a bit
of time when we support both. This is a better way to support the old
way where the driver hand rolls things itself.
A new notes about the implementation here:
* When using the drm_bridge_connector the connector should be created
after all the bridges, so we change the ordering a bit.
* I'm reasonably certain that we don't need to do anything to "free"
the new drm_bridge_connector. If drm_bridge_connector_init() returns
success then we know drm_connector_init() was called with the
`drm_bridge_connector_funcs`. The `drm_bridge_connector_funcs` has a
.destroy() that does all the cleanup. drm_connector_init() calls
__drm_mode_object_add() with a drm_connector_free() that will call
the .destroy().
* I'm also reasonably certain that I don't need to "undo" the
drm_bridge_attach() if drm_bridge_connector_init() fails. The
"detach" function is private and other similar code doesn't try to
undo the drm_bridge_attach() in error cases. There's also a comment
indicating the lack of balance at the top of drm_bridge_attach().
[1] https://lore.kernel.org/r/20210920225801.227211-4-robdclark@gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.1.I3ab26b7f197cc56c874246a43e57913e9c2c1028@changeid
|
|
Move drm_dp_aux_bus.c and its header file into the DP subdirectory
and update all users. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-6-tzimmermann@suse.de
|
|
Move all public DisplayPort headers into dp/ and update users. No
functional changes.
v3:
* rebased onto latest drm-tip
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-5-tzimmermann@suse.de
|
|
Set the maximum register to 0xff so we can dump the registers for this
device in debugfs.
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Cc: Rob Clark <robdclark@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215002529.382383-1-swboyd@chromium.org
|
|
Otherwise we don't get another shot at it if the bridge probes before
the dsi host is registered. It seems like this is what *most* (but not
all) of the other bridges do.
It looks like this was missed in the conversion to attach dsi host at
probe time.
Fixes: c3b75d4734cb ("drm/bridge: sn65dsi86: Register and attach our DSI device at probe")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: squashed in Stephen's simplification]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211207215753.635841-1-robdclark@gmail.com
|
|
When built without CONFIG_PWM there are no references to
ti_sn65dsi86_read_u16(), avoid the W=1 build warning by marking the
function as __maybe_unused.
__maybe_unused is used insted of a #ifdef guard as it looks slighly
cleaner and it avoids issues if in the future other permutations of the
config options would use the function.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: cea86c5bb442 ("drm/bridge: ti-sn65dsi86: Implement the pwm_chip")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028163548.273736-1-bjorn.andersson@linaro.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
|
|
In order to avoid any probe ordering issue, the best practice is to move
the secondary MIPI-DSI device registration and attachment to the
MIPI-DSI host at probe time. Let's do this.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025151536.1048186-18-maxime@cerno.tech
|
|
Let's switch to the new devm MIPI-DSI function to register and attach
our secondary device. This also avoids leaking the device when we detach
the bridge.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025151536.1048186-17-maxime@cerno.tech
|
|
The SN65DSI86 provides the ability to supply a PWM signal on GPIO 4,
with the primary purpose of controlling the backlight of the attached
panel. Add an implementation that exposes this using the standard PWM
framework, to allow e.g. pwm-backlight to expose this to the user.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025170925.3096444-3-bjorn.andersson@linaro.org
|
|
The multi-register u16 write operation can use regmap_bulk_write()
instead of two separate regmap_write() calls.
It's uncertain if this has any effect on the actual updates of the
underlying registers, but this at least gives the hardware the
opportunity and saves us one transation on the bus.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025170925.3096444-2-bjorn.andersson@linaro.org
|
|
For the brave new world of bridges not creating their own connectors, we
need to implement the max clock limitation via bridge->mode_valid()
instead of connector->mode_valid().
v2: Drop unneeded connector->mode_valid()
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210920225801.227211-3-robdclark@gmail.com
|
|
If we created our own connector because the driver does not support the
NO_CONNECTOR flag, we don't want the downstream bridge to *also* create
a connector. And if this driver did pass the NO_CONNECTOR flag (and we
supported that mode) this would change nothing.
Fixes: 4e5763f03e10 ("drm/bridge: ti-sn65dsi86: Wrap panel with panel-bridge")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811235253.924867-2-robdclark@gmail.com
|
|
The manual has always said that we need 100 us delays in a few
places. Though it hasn't seemed to be a big deal to skip these, let's
add them in case it makes something happier.
NOTE: this fixes no known issues but it seems good to make it right.
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.3.I842d483139531aa4651da8338512fdf0171ff23c@changeid
|
|
When testing with a panel that's apparently a little more persnickety
about the correct power sequence (specifically Samsung ATNA33XC20), we
found that the ti-sn65dsi86 was doing things just slightly wrong.
Looking closely at the ti-sn65dsi86's datasheet, the power off
sequence is supposed to be:
1. Clear VSTREAM_ENABLE bit
2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state.
3. Program the ML_TX_MODE to 0x0 (OFF)
4. Program the DP_NUM_LANES register to 0x0
5. Clear the DP_PLL_EN bit.
6. Deassert the EN pin.
7. Remove power from supply pins
Since we were doing the whole sequence in the "disable", I believe
that step #2 (stopping the DSI stream from the GPU) wasn't
happening. We also weren't setting DP_NUM_LANES to 0.
Let's fix this.
NOTE: things are a little asymmetric now. For instance, we turn the
PLL on in "enable" but now we're not turning it off until
"post_disable". It would seem to make sense to move the PLL turning on
to "pre_enable" to match. Unfortunately, I don't believe that's
allowed. It looks as if (in the non-refclk mode which probably nobody
is using) we have to wait until the MIPI clock is there before we can
enable the PLL. In any case, the way it is here won't really
hurt--it'll just leave the PLL on a little longer.
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.2.If8a8ec3bf1855cf0dbb62c005a71d6698c99c125@changeid
|
|
To prepare for making connector creation option, move connector creation
out of ti_sn_bridge_attach to a separate function.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624000304.16281-7-laurent.pinchart+renesas@ideasonboard.com
|
|
Reorganize the functions in sections, related to connector operations,
bridge operations, AUX adapter, GPIO controller and probe & remove.
This prepares for proper support of DRM_BRIDGE_ATTACH_NO_CONNECTOR that
will add more functions, to ensure that the code will stay readable.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624000304.16281-6-laurent.pinchart+renesas@ideasonboard.com
|
|
To simplify interfacing with the panel, wrap it in a panel-bridge and
let the DRM bridge helpers handle chaining of operations.
This also prepares for support of DRM_BRIDGE_ATTACH_NO_CONNECTOR, which
requires all components in the display pipeline to be represented by
bridges.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624000304.16281-5-laurent.pinchart+renesas@ideasonboard.com
|
|
The valid rates are stored in an array of 8 booleans. Replace it with a
bitmask to save space.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624000304.16281-4-laurent.pinchart+renesas@ideasonboard.com
|
|
The enable signal may not be controllable by the kernel. Make it
optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624000304.16281-3-laurent.pinchart+renesas@ideasonboard.com
|
|
As I was testing to make sure that the DEFER path worked well with my
patch series, I got tired of seeing this scary message in my logs just
because the panel needed to defer:
[drm:ti_sn_bridge_probe] *ERROR* could not find any panel node
Let's use dev_err_probe() which nicely quiets this error and also
simplifies the code a tiny bit. We'll also update other places in the
file which can use dev_err_probe().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.10.I24bba069e63b1eea84443eef0c8535fd032a6311@changeid
|
|
This is really just a revert of commit 58074b08c04a ("drm/bridge:
ti-sn65dsi86: Read EDID blob over DDC"), resolving conflicts.
The old code failed to read the EDID properly in a very important
case: before the bridge's pre_enable() was called. The way things need
to work:
1. Read the EDID.
2. Based on the EDID, decide on video settings and pixel clock.
3. Enable the bridge w/ the desired settings.
The way things were working:
1. Try to read the EDID but fail; fall back to hardcoded values.
2. Based on hardcoded values, decide on video settings and pixel clock.
3. Enable the bridge w/ the desired settings.
4. Try again to read the EDID, it works now!
5. Realize that the hardcoded settings weren't quite right.
6. Disable / reenable the bridge w/ the right settings.
The reasons for the failures were twofold:
a) Since we never ran the bridge chip's pre-enable then we never set
the bit to ignore HPD. This meant the bridge chip didn't even _try_
to go out on the bus and communicate with the panel.
b) Even if we fixed things to ignore HPD, the EDID still wouldn't read
if the panel wasn't on.
Instead of reverting the code, we could fix it to set the HPD bit and
also power on the panel. However, it also works nicely to just let the
panel code read the EDID. Now that we've split the driver up we can
expose the DDC AUX channel bus to the panel node. The panel can take
charge of reading the EDID.
NOTE: in order for things to work, anyone that needs to read the EDID
will need to instantiate their panel using the new DP AUX bus (AKA by
listing their panel under the "aux-bus" node of the bridge chip in the
device tree).
In the future if we want to use the bridge chip to provide a full
external DP port (which won't have a panel) then we will have to
conditinally add EDID reading back in.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.9.I9330684c25f65bb318eff57f0616500f83eac3cc@changeid
|
|
We want to provide our panel with access to the DP AUX channel. The
way to do this is to let our panel be a child of ours using the fancy
new DP AUX bus support.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.8.Ib5fe0638da85800141ce141bb8e441c5f25438d4@changeid
|
|
On its own, this change looks a little strange and doesn't do too much
useful. To understand why we're doing this we need to look forward to
future patches where we're going to probe our panel using the new DP
AUX bus. See the patch ("drm/bridge: ti-sn65dsi86: Add support for the
DP AUX bus").
Let's think about the set of steps we'll want to happen when we have
the DP AUX bus:
1. We'll create the DP AUX bus.
2. We'll populate the devices on the DP AUX bus (AKA our panel).
3. For setting up the bridge-related functions of ti-sn65dsi86 we'll
need to get a reference to the panel.
If we do #1 - #3 in a single probe call things _mostly_ will work, but
it won't be massively robust. Let's explore.
First let's think of the easy case of no -EPROBE_DEFER. In that case
in step #2 when we populate the devices on the DP AUX bus it will
actually try probing the panel right away. Since the panel probe
doesn't defer then in step #3 we'll get a reference to the panel and
we're golden.
Second, let's think of the case when the panel returns
-EPROBE_DEFER. In that case step #2 won't synchronously create the
panel (it'll just add the device to the defer list to do it
later). Step #3 will fail to get the panel and the bridge sub-device
will return -EPROBE_DEFER. We'll depopulate the DP AUX bus. Later
we'll try the whole sequence again. Presumably the panel will
eventually stop returning -EPROBE_DEFER and we'll go back to the first
case where things were golden. So this case is OK too even if it's a
bit ugly that we have to keep creating / deleting the AUX bus over and
over.
So where is the problem? As I said, it's mostly about robustness. I
don't believe that step #2 (creating the sub-devices) is really
guaranteed to be synchronous. This is evidenced by the fact that it's
allowed to "succeed" by just sticking the device on the deferred
list. If anything about the process changes in Linux as a whole and
step #2 just kicks off the probe of the DP AUX endpoints (our panel)
in the background then we'd be in trouble because we might never get
the panel in step #3.
Adding an extra sub-device means we just don't need to worry about
it. We'll create the sub-device for the DP AUX bus and it won't go
away until the whole ti-sn65dsi86 driver goes away. If the bridge
sub-device defers (maybe because it can't find the panel) that won't
depopulate the DP AUX bus and so we don't need to worry about it.
NOTE: there's a little bit of a trick here. Though the AUX channel can
run without the MIPI-to-eDP bits of the code, the MIPI-to-eDP bits
can't run without the AUX channel. We could come up a complicated
signaling scheme (have the MIPI-to-eDP bits return EPROBE_DEFER for a
while or wait on some sort of completion), but it seems simple enough
to just not even bother creating the bridge device until the AUX
channel probes. That's what we'll do.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.7.If89144992cb9d900f8c91a8d1817dbe00f543720@changeid
|
|
The ti_sn_aux_transfer() function returns ssize_t (signed long). It's
supposed to return negative error codes or the number of bytes
transferred. The "ret" variable is int and the "len" variable is
unsigned int.
The problem is that with a ternary like this, the negative int is first
type promoted to unsigned int to match "len" at this point it is a high
positive value. Then when it is type promoted to ssize_t (s64) it
remains a high positive value instead of sign extending and becoming a
negative again.
Fix this by removing the ternary.
Fixes: b137406d9679 ("drm/bridge: ti-sn65dsi86: If refclk, DP AUX can happen w/out pre-enable")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/YKOGogHasIyvF8nj@mwanda
|
|
The ti_sn_gpio_unregister() is not just called from the remove path
but also from the error handling of the init path. That means it can't
have the __exit annotation.
Fixes: bf73537f411b ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210504073845.1.Ibf4194f4252846edaa0c6a6c7b86588f75ad5529@changeid
|
|
Let's reorganize how we init and turn on the reference clock in the
code to allow us to turn it on early (even before pre_enable()) so
that we can read the EDID early. This is handy for eDP because:
- We always assume that a panel is there.
- Once we report that a panel is there we get asked to read the EDID.
- Pre-enable isn't called until we know what pixel clock we want to
use and we're ready to turn everything on. That's _after_ we get
asked to read the EDID.
NOTE: the above only works out OK if we "refclk" is provided. Though I
don't have access to any hardware that uses ti-sn65dsi86 and _doesn't_
provide a "refclk", I believe that we'll have trouble reading the EDID
at bootup in that case. Specifically I believe that if there's no
"refclk" we need the MIPI source clock to be active before we can
successfully read the EDID. My evidence here is that, in testing, I
couldn't read the EDID until I turned on the DPPLL in the bridge chip
and that the DPPLL needs the input clock to be active.
Since this is hard to support, let's punt trying to handle this case
if there's no "refclk". In that case we'll enable comms in
pre_enable() like we always did.
I don't believe there are any users of the ti-sn65dsi86 bridge chip
that _don't_ use "refclk". The bridge chip is _very_ inflexible in
that mode. The only time I've seen that mode used was for some really
early prototype hardware that was thrown in the e-waste bin years ago
when we realized how inflexible it was.
Even if someone is using the bridge chip without the "refclk" they're
in no worse shape than they were before the (fairly recent) commit
58074b08c04a ("drm/bridge: ti-sn65dsi86: Read EDID blob over DDC").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.13.Ie8cf556114953c6e7634564cc0d3ddbd103cb96c@changeid
|
|
No functional changes--this just makes the diffstat of a future change
easier to understand.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.12.I047b8c7c6a3fc60eaca473da7a374f171fb021c2@changeid
|
|
Let's make the bridge use autosuspend with a 500ms delay. This is in
preparation for promoting DP AUX transfers to their own sub-driver so
that we're not constantly powering up and down the device as we
transfer all the chunks.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.11.I4c0b4a87e4dc19e5023b4d0a21bbfa6d9c09ebd8@changeid
|
|
Let's use the newly minted aux bus to break up the driver into sub
drivers. We're not doing a full breakup here: all the code is still in
the same file and remains largely untouched. The big goal here of
using sub-drivers is to allow part of our code to finish probing even
if some other code needs to defer. This can solve some chicken-and-egg
problems. Specifically:
- In commit 48834e6084f1 ("drm/panel-simple: Support hpd-gpios for
delaying prepare()") we had to add a bit of a hack to simpel-panel
to support HPD showing up late. We can get rid of that hack now
since the GPIO part of our driver can finish probing early.
- We have a desire to expose our DDC bus to simple-panel (and perhaps
to a backlight driver?). That will end up with the same
chicken-and-egg problem. A future patch to move this to a sub-driver
will fix it.
- If/when we support the PWM functionality present in the bridge chip
for a backlight we'll end up with another chicken-and-egg
problem. If we allow the PWM to be a sub-driver too then it solves
this problem.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.9.I3e68fa38c4ccbdbdf145cad2b01e83a1e5eac302@changeid
|
|
This is just code motion of the probe routine to move all the things
that are for the "whole chip" (instead of the GPIO parts or the
MIPI-to-eDP parts) together at the start of probe. This is in
preparation for breaking the driver into sub-drivers.
Since we're using devm for all of the "whole chip" stuff this is
actually quite easy now.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.8.Ide8ba40feb2e43bc98a11edbb08d696d62dcd83e@changeid
|
|
Let's:
- Set the drvdata as soon as it's allocated. This just sets up a
pointer so there's no downside here.
- Remove the useless call to i2c_set_clientdata() which is literally
the same thing as dev_set_drvdata().
No functional changes intended.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.7.If5d4d4e22e97bebcd493b76765c1759527705620@changeid
|
|
Tiny cleanup for probe so we don't keep having to specify
"&client->dev" or "pdata->dev". No functional changes intended.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.6.I83925d8ca228bdc5f55b17854c90754efc6a470e@changeid
|
|
Let's cleanup the debugfs code to:
- Check for errors.
- Use devm to manage freeing, which also means we don't need to store
a pointer in our structure.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.5.I5fe072753290c6a77eda736ebd5778e17b7cb0fb@changeid
|
