| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds device tree bindings for ARM Firmware Suite
flash partitioning used in NOR flashes on ARM reference
designs.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Add an example showing how to use the addr-gpios property to deal with a
system with limited IO space.
Cc: devicetree@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Describe how to use the BCM963XX ImageTag format in a mixed flash layout
environment.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Add binding documentation for the standard CFE based BCM963XX flash
layout, found in most devices using a BCM63XX SoC with NOR flash.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The A23/A33 NAND controller is slightly different than the A10+ ones,
eg. DMA handling is a bit different and a few register offsets
changed.
Introduce a new compatible to represent this version of the IP.
Also append '-controller' to the new compatible (which is required for
new compatibles) as this is describing a NAND controller and not a
NAND chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Switch the DT binding to a YAML schema to enable the DT validation.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The NAND chips in MTD have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently, this driver sticks to the legacy NAND model because it was
upstreamed before commit 2d472aba15ff ("mtd: nand: document the NAND
controller/NAND chip DT representation"). However, relying on the
dummy_controller is already deprecated.
Switch over to the new controller/chip representation.
The struct denali_nand_info has been split into denali_controller
and denali_chip, to contain the controller data, per-chip data,
respectively.
One problem is, this commit changes the DT binding. So, as always,
the backward compatibility must be taken into consideration.
In the new binding, the controller node expects
#address-cells = <1>;
#size-cells = <0>;
... since the child nodes represent NAND chips.
In the old binding, the controller node may have subnodes, but they
are MTD partitions.
The denali_dt_is_legacy_binding() exploits it to distinguish old/new
platforms.
Going forward, the old binding is only allowed for existing DT files.
I updated the binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The 'ingenic,bch-controller' property is now deprecated and the
'ecc-engine' property should be used instead.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
sense to use the more generic ECC term.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add compatible strings to probe the jz4780-nand and jz4780-bch drivers
from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add compatibility string for the sam9x60 nand controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
|
|
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
|
|
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This updates bindings for the MT7629 SPI-NOR controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
This patch adds the documentation of the device tree bindings for the STM32
FMC2 NAND controller.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Move the documentation of the old SPI NOR driver to the place of the new
SPI memory interface based driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
|
|
This adds device tree bindings for the RedBoot FIS partition
format.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Atmel SAMA5D2 QuadSPI driver was moved from mtd to spi subsystem,
this change is just moving DT-binding documentation.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add documentation for the addr-gpios. This extension to the physmap
binding allow creating flash devices that are paged using GPIOs.
Cc: devicetree@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
* tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: remove dynamic-resolution-notes reference to non-existent file
dt-bindings: Add Y Soft Corporation vendor prefix
of/fdt: Remove PPC32 longtrail hack in memory scan
dt-bindings: remove 'interrupt-parent' from bindings
pinctrl: tegra: fix spelling in devicetree binding document
usb: dwc3: rockchip: Fix PHY documentation links.
dt-bindings: sound: wm8994: document wlf,csnaddr-pd property
dt-bindings: sound: wm8994: document wlf,spkmode-pu property
dt-bindings: sram: Add 'clocks' as an optional property
dt-bindings: Add vendor prefix for AsusTek Computer Inc.
dt-bindings: misc: ASPEED coprocessor interrupt controller
dt-bindings: gpio: pca953x: Document interrupts, update example
drivers/of: Make of_io_request_and_map() "name" argument optional
dt-bindings: Add bitmain vendor prefix
Documentation: devicetree: tilcdc: fix spelling mistake "suppors" -> "supports"
|
|
Pull SPI NOR updates from Boris Brezillon:
"
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
"
|
|
Pull NAND updates from Miquel Raynal:
"
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
"
|
|
Commit 59b356ffd0b0 ("mtd: m25p80: restore the status of SPI flash when
exiting") is the latest from a long history of attempts to add reboot
handling to handle stateful addressing modes on SPI flash. Some prior
mostly-related discussions:
http://lists.infradead.org/pipermail/linux-mtd/2013-March/046343.html
[PATCH 1/3] mtd: m25p80: utilize dedicated 4-byte addressing commands
http://lists.infradead.org/pipermail/barebox/2014-September/020682.html
[RFC] MTD m25p80 3-byte addressing and boot problem
http://lists.infradead.org/pipermail/linux-mtd/2015-February/057683.html
[PATCH 2/2] m25p80: if supported put chip to deep power down if not used
Previously, attempts to add reboot-time software reset handling were
rejected, but the latest attempt was not.
Quick summary of the problem:
Some systems (e.g., boot ROM or bootloader) assume that they can read
initial boot code from their SPI flash using 3-byte addressing. If the
flash is left in 4-byte mode after reset, these systems won't boot. The
above patch provided a shutdown/remove hook to attempt to reset the
addressing mode before we reboot. Notably, this patch misses out on
huge classes of unexpected reboots (e.g., crashes, watchdog resets).
Unfortunately, it is essentially impossible to solve this problem 100%:
if your system doesn't know how to reset the SPI flash to power-on
defaults at initialization time, no amount of software can really rescue
you -- there will always be a chance of some unexpected reset that
leaves your flash in an addressing mode that your boot sequence didn't
expect.
While it is not directly harmful to perform hacks like the
aforementioned commit on all 4-byte addressing flash, a
properly-designed system should not need the hack -- and in fact,
providing this hack may mask the fact that a given system is indeed
broken. So this patch attempts to apply this unsound hack more narrowly,
providing a strong suggestion to developers and system designers that
this is truly a hack. With luck, system designers can catch their errors
early on in their development cycle, rather than applying this hack long
term. But apparently enough systems are out in the wild that we still
have to provide this hack.
Document a new device tree property to denote systems that do not have a
proper hardware (or software) reset mechanism, and apply the hack (with
a loud warning) only in this case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Documentation was already saying that fixed and dynamic partitioning can
be mixed but was missing a clear description and examples. This commit
adds a proper documentation of how descriptions can be nested and how
layouts can be mixed.
This addition is important for partitions that contain subpartitions.
In such cases partitions have to be properly described in order to let
system handle them correctly.
Depending on situation, nesting descriptions may provide more accurate
logic/structure and/or allow mixing partitioning types (various
"compatible" values).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Commit 30f9f2fb7ba0 ("mtd: denali: add a DT driver") supported the
clock enablement, but did not document it in the DT binding.
In addition to the existing clock, this commit adds more clocks based
on the IP specification.
According to the Denali User's Guide, this IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
The driver should accept the current single clock for the backward
compatibility, but the DT binding should represent the real hardware,
and future platforms must follow this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add bindings for SPI NAND chips.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
1. If nand-ecc-strength specified in DT, then controller will use
this ECC strength otherwise ECC strength will be calculated
according to chip requirement and available OOB size.
2. QCOM NAND controller supports only one step size (512 bytes) but
nand-ecc-step-size is required property in DT. This DT property
can be removed and ecc step size can be assigned in driver with
512 bytes value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Broadcom based home router devices use TRX firmware format. It's a
container that can hold few partitions. If operating system is expected
to access them it has to understand that format and parse flash data
accordingly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This adds the devicetree binding for the Tegra 2 NAND flash
controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
|
|
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
|
|
Broadcom based home router devices use partitions which have to be
discovered in a specific way. They are not fixed and there is not any
standard partition table. This commit adds and describes a new custom
binding for such devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Update ecc step size, ecc strength, and parity bits supported on
each MTK NAND controller.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
None of the existing platforms connect the R/B pin to a GPIO (they all
use one of the dedicated R/B pin).
Anyway, if we ever get short of native R/B pins, it's probably better
to fallback to STATUS reg polling than trying to poll a GPIO.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Document newly supported device tree properties nand-ecc-strength/
nand-ecc-step-size to specify ECC strength/size.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
directories
Bindings are supposed to be organized by device class/function. Move a
couple of powerpc 4xx bindings to the correct binding directory.
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Whack-a-mole some more occurrences of status in examples.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
|
|
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
|
|
Improve the bindings example by adding an example of how to represent
two SPI NOR devices.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Provide a way to specify the endianness to use when accessing a
memory-mapped flash.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
