summaryrefslogtreecommitdiffstats
path: root/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/mac80211.h')
-rw-r--r--include/net/mac80211.h197
1 files changed, 34 insertions, 163 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 277488176a44..460da54a0019 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -69,95 +69,6 @@
* not do so then mac80211 may add this under certain circumstances.
*/
-#define IEEE80211_CHAN_W_SCAN 0x00000001
-#define IEEE80211_CHAN_W_ACTIVE_SCAN 0x00000002
-#define IEEE80211_CHAN_W_IBSS 0x00000004
-
-/* Channel information structure. Low-level driver is expected to fill in chan,
- * freq, and val fields. Other fields will be filled in by 80211.o based on
- * hostapd information and low-level driver does not need to use them. The
- * limits for each channel will be provided in 'struct ieee80211_conf' when
- * configuring the low-level driver with hw->config callback. If a device has
- * a default regulatory domain, IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED
- * can be set to let the driver configure all fields */
-struct ieee80211_channel {
- short chan; /* channel number (IEEE 802.11) */
- short freq; /* frequency in MHz */
- int val; /* hw specific value for the channel */
- int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */
- unsigned char power_level;
- unsigned char antenna_max;
-};
-
-#define IEEE80211_RATE_ERP 0x00000001
-#define IEEE80211_RATE_BASIC 0x00000002
-#define IEEE80211_RATE_PREAMBLE2 0x00000004
-#define IEEE80211_RATE_SUPPORTED 0x00000010
-#define IEEE80211_RATE_OFDM 0x00000020
-#define IEEE80211_RATE_CCK 0x00000040
-#define IEEE80211_RATE_MANDATORY 0x00000100
-
-#define IEEE80211_RATE_CCK_2 (IEEE80211_RATE_CCK | IEEE80211_RATE_PREAMBLE2)
-#define IEEE80211_RATE_MODULATION(f) \
- (f & (IEEE80211_RATE_CCK | IEEE80211_RATE_OFDM))
-
-/* Low-level driver should set PREAMBLE2, OFDM and CCK flags.
- * BASIC, SUPPORTED, ERP, and MANDATORY flags are set in 80211.o based on the
- * configuration. */
-struct ieee80211_rate {
- int rate; /* rate in 100 kbps */
- int val; /* hw specific value for the rate */
- int flags; /* IEEE80211_RATE_ flags */
- int val2; /* hw specific value for the rate when using short preamble
- * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for
- * 2, 5.5, and 11 Mbps) */
- signed char min_rssi_ack;
- unsigned char min_rssi_ack_delta;
-
- /* following fields are set by 80211.o and need not be filled by the
- * low-level driver */
- int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for
- * optimizing channel utilization estimates */
-};
-
-/**
- * enum ieee80211_phymode - PHY modes
- *
- * @MODE_IEEE80211A: 5GHz as defined by 802.11a/802.11h
- * @MODE_IEEE80211B: 2.4 GHz as defined by 802.11b
- * @MODE_IEEE80211G: 2.4 GHz as defined by 802.11g (with OFDM),
- * backwards compatible with 11b mode
- * @NUM_IEEE80211_MODES: internal
- */
-enum ieee80211_phymode {
- MODE_IEEE80211A,
- MODE_IEEE80211B,
- MODE_IEEE80211G,
-
- /* keep last */
- NUM_IEEE80211_MODES
-};
-
-/**
- * struct ieee80211_ht_info - describing STA's HT capabilities
- *
- * This structure describes most essential parameters needed
- * to describe 802.11n HT capabilities for an STA.
- *
- * @ht_supported: is HT supported by STA, 0: no, 1: yes
- * @cap: HT capabilities map as described in 802.11n spec
- * @ampdu_factor: Maximum A-MPDU length factor
- * @ampdu_density: Minimum A-MPDU spacing
- * @supp_mcs_set: Supported MCS set as described in 802.11n spec
- */
-struct ieee80211_ht_info {
- u8 ht_supported;
- u16 cap; /* use IEEE80211_HT_CAP_ */
- u8 ampdu_factor;
- u8 ampdu_density;
- u8 supp_mcs_set[16];
-};
-
/**
* struct ieee80211_ht_bss_info - describing BSS's HT characteristics
*
@@ -175,30 +86,6 @@ struct ieee80211_ht_bss_info {
};
/**
- * struct ieee80211_hw_mode - PHY mode definition
- *
- * This structure describes the capabilities supported by the device
- * in a single PHY mode.
- *
- * @list: internal
- * @channels: pointer to array of supported channels
- * @rates: pointer to array of supported bitrates
- * @mode: the PHY mode for this definition
- * @num_channels: number of supported channels
- * @num_rates: number of supported bitrates
- * @ht_info: PHY's 802.11n HT abilities for this mode
- */
-struct ieee80211_hw_mode {
- struct list_head list;
- struct ieee80211_channel *channels;
- struct ieee80211_rate *rates;
- enum ieee80211_phymode mode;
- int num_channels;
- int num_rates;
- struct ieee80211_ht_info ht_info;
-};
-
-/**
* struct ieee80211_tx_queue_params - transmit queue configuration
*
* The information provided in this structure is required for QoS
@@ -320,11 +207,13 @@ struct ieee80211_bss_conf {
struct ieee80211_tx_control {
struct ieee80211_vif *vif;
- int tx_rate; /* Transmit rate, given as the hw specific value for the
- * rate (from struct ieee80211_rate) */
- int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw
- * specific value for the rate (from
- * struct ieee80211_rate) */
+ struct ieee80211_rate *tx_rate;
+
+ /* Transmit rate for RTS/CTS frame */
+ struct ieee80211_rate *rts_cts_rate;
+
+ /* retry rate for the last retries */
+ struct ieee80211_rate *alt_retry_rate;
#define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for
* this frame */
@@ -343,6 +232,7 @@ struct ieee80211_tx_control {
#define IEEE80211_TXCTL_REQUEUE (1<<7)
#define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of
* the frame */
+#define IEEE80211_TXCTL_SHORT_PREAMBLE (1<<9)
#define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send
* using the through
* set_retry_limit configured
@@ -359,20 +249,11 @@ struct ieee80211_tx_control {
u8 retry_limit; /* 1 = only first attempt, 2 = one retry, ..
* This could be used when set_retry_limit
* is not implemented by the driver */
- u8 power_level; /* per-packet transmit power level, in dBm */
u8 antenna_sel_tx; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
u8 icv_len; /* length of the ICV/MIC field in octets */
u8 iv_len; /* length of the IV field in octets */
u8 queue; /* hardware queue to use for this frame;
* 0 = highest, hw->queues-1 = lowest */
- struct ieee80211_rate *rate; /* internal 80211.o rate */
- struct ieee80211_rate *rts_rate; /* internal 80211.o rate
- * for RTS/CTS */
- int alt_retry_rate; /* retry rate for the last retries, given as the
- * hw specific value for the rate (from
- * struct ieee80211_rate). To be used to limit
- * packet dropping when probing higher rates, if hw
- * supports multiple retry rates. -1 = not used */
int type; /* internal */
};
@@ -415,26 +296,24 @@ enum mac80211_rx_flags {
* supported by hardware) to the 802.11 code with each received
* frame.
* @mactime: MAC timestamp as defined by 802.11
+ * @band: the active band when this frame was received
* @freq: frequency the radio was tuned to when receiving this frame, in MHz
- * @channel: channel the radio was tuned to
- * @phymode: active PHY mode
* @ssi: signal strength when receiving this frame
* @signal: used as 'qual' in statistics reporting
* @noise: PHY noise when receiving this frame
* @antenna: antenna used
- * @rate: data rate
+ * @rate_idx: index of data rate into band's supported rates
* @flag: %RX_FLAG_*
*/
struct ieee80211_rx_status {
u64 mactime;
+ enum ieee80211_band band;
int freq;
- int channel;
- enum ieee80211_phymode phymode;
int ssi;
int signal;
int noise;
int antenna;
- int rate;
+ int rate_idx;
int flag;
};
@@ -509,41 +388,30 @@ enum ieee80211_conf_flags {
*
* @radio_enabled: when zero, driver is required to switch off the radio.
* TODO make a flag
- * @channel: IEEE 802.11 channel number
- * @freq: frequency in MHz
- * @channel_val: hardware specific channel value for the channel
- * @phymode: PHY mode to activate (REMOVE)
- * @chan: channel to switch to, pointer to the channel information
- * @mode: pointer to mode definition
- * @regulatory_domain: ??
* @beacon_int: beacon interval (TODO make interface config)
* @flags: configuration flags defined above
- * @power_level: transmit power limit for current regulatory domain in dBm
- * @antenna_max: maximum antenna gain
+ * @power_level: requested transmit power (in dBm)
+ * @max_antenna_gain: maximum antenna gain (in dBi)
* @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
* 1/2: antenna 0/1
* @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
* @ht_conf: describes current self configuration of 802.11n HT capabilies
* @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
+ * @channel: the channel to tune to
*/
struct ieee80211_conf {
- int channel; /* IEEE 802.11 channel number */
- int freq; /* MHz */
- int channel_val; /* hw specific value for the channel */
-
- enum ieee80211_phymode phymode;
- struct ieee80211_channel *chan;
- struct ieee80211_hw_mode *mode;
unsigned int regulatory_domain;
int radio_enabled;
int beacon_int;
u32 flags;
- u8 power_level;
- u8 antenna_max;
+ int power_level;
+ int max_antenna_gain;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+ struct ieee80211_channel *channel;
+
struct ieee80211_ht_info ht_conf;
struct ieee80211_ht_bss_info ht_bss_conf;
};
@@ -764,15 +632,19 @@ enum sta_notify_cmd {
* %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
* otherwise the stack will not know when the DTIM beacon was sent.
*
- * @IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED:
- * Channels are already configured to the default regulatory domain
- * specified in the device's EEPROM
+ * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
+ * Hardware is not capable of short slot operation on the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
+ * Hardware is not capable of receiving frames with short preamble on
+ * the 2.4 GHz band.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
- IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED = 1<<3,
+ IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
+ IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
};
/**
@@ -784,7 +656,8 @@ enum ieee80211_hw_flags {
* @wiphy: This points to the &struct wiphy allocated for this
* 802.11 PHY. You must fill in the @perm_addr and @dev
* members of this structure using SET_IEEE80211_DEV()
- * and SET_IEEE80211_PERM_ADDR().
+ * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
+ * bands (with channels, bitrates) are registered here.
*
* @conf: &struct ieee80211_conf, device configuration, don't use.
*
@@ -1062,7 +935,9 @@ enum ieee80211_ampdu_mlme_action {
* given local_address is enabled.
*
* @hw_scan: Ask the hardware to service the scan request, no need to start
- * the scan state machine in stack.
+ * the scan state machine in stack. The scan must honour the channel
+ * configuration done by the regulatory agent in the wiphy's registered
+ * bands.
*
* @get_stats: return low-level statistics
*
@@ -1284,10 +1159,6 @@ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
#endif
}
-/* Register a new hardware PHYMODE capability to the stack. */
-int ieee80211_register_hwmode(struct ieee80211_hw *hw,
- struct ieee80211_hw_mode *mode);
-
/**
* ieee80211_unregister_hw - Unregister a hardware device
*
@@ -1461,7 +1332,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame.
- * @rate: the rate (in 100kbps) at which the frame is going to be transmitted.
+ * @rate: the rate at which the frame is going to be transmitted.
*
* Calculate the duration field of some generic frame, given its
* length and transmission rate (in 100kbps).
@@ -1469,7 +1340,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
size_t frame_len,
- int rate);
+ struct ieee80211_rate *rate);
/**
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames