diff options
Diffstat (limited to 'include/net/cfg80211.h')
| -rw-r--r-- | include/net/cfg80211.h | 135 |
1 files changed, 95 insertions, 40 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 814be4b4200c..b7aba6e1a586 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -311,6 +311,34 @@ struct ieee80211_supported_band { struct ieee80211_sta_vht_cap vht_cap; }; +/** + * wiphy_read_of_freq_limits - read frequency limits from device tree + * + * @wiphy: the wireless device to get extra limits for + * + * Some devices may have extra limitations specified in DT. This may be useful + * for chipsets that normally support more bands but are limited due to board + * design (e.g. by antennas or external power amplifier). + * + * This function reads info from DT and uses it to *modify* channels (disable + * unavailable ones). It's usually a *bad* idea to use it in drivers with + * shared channel data as DT limitations are device specific. You should make + * sure to call it only if channels in wiphy are copied and can be modified + * without affecting other devices. + * + * As this function access device node it has to be called after set_wiphy_dev. + * It also modifies channels so they have to be set first. + * If using this helper, call it before wiphy_register(). + */ +#ifdef CONFIG_OF +void wiphy_read_of_freq_limits(struct wiphy *wiphy); +#else /* CONFIG_OF */ +static inline void wiphy_read_of_freq_limits(struct wiphy *wiphy) +{ +} +#endif /* !CONFIG_OF */ + + /* * Wireless hardware/device configuration structures and methods */ @@ -1592,6 +1620,17 @@ struct cfg80211_sched_scan_plan { }; /** + * struct cfg80211_bss_select_adjust - BSS selection with RSSI adjustment. + * + * @band: band of BSS which should match for RSSI level adjustment. + * @delta: value of RSSI level adjustment. + */ +struct cfg80211_bss_select_adjust { + enum nl80211_band band; + s8 delta; +}; + +/** * struct cfg80211_sched_scan_request - scheduled scan request description * * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans) @@ -1626,6 +1665,16 @@ struct cfg80211_sched_scan_plan { * cycle. The driver may ignore this parameter and start * immediately (or at any other time), if this feature is not * supported. + * @relative_rssi_set: Indicates whether @relative_rssi is set or not. + * @relative_rssi: Relative RSSI threshold in dB to restrict scan result + * reporting in connected state to cases where a matching BSS is determined + * to have better or slightly worse RSSI than the current connected BSS. + * The relative RSSI threshold values are ignored in disconnected state. + * @rssi_adjust: delta dB of RSSI preference to be given to the BSSs that belong + * to the specified band while deciding whether a better BSS is reported + * using @relative_rssi. If delta is a negative number, the BSSs that + * belong to the specified band will be penalized by delta dB in relative + * comparisions. */ struct cfg80211_sched_scan_request { struct cfg80211_ssid *ssids; @@ -1645,6 +1694,10 @@ struct cfg80211_sched_scan_request { u8 mac_addr[ETH_ALEN] __aligned(2); u8 mac_addr_mask[ETH_ALEN] __aligned(2); + bool relative_rssi_set; + s8 relative_rssi; + struct cfg80211_bss_select_adjust rssi_adjust; + /* internal */ struct wiphy *wiphy; struct net_device *dev; @@ -1953,17 +2006,6 @@ struct cfg80211_ibss_params { }; /** - * struct cfg80211_bss_select_adjust - BSS selection with RSSI adjustment. - * - * @band: band of BSS which should match for RSSI level adjustment. - * @delta: value of RSSI level adjustment. - */ -struct cfg80211_bss_select_adjust { - enum nl80211_band band; - s8 delta; -}; - -/** * struct cfg80211_bss_selection - connection parameters for BSS selection. * * @behaviour: requested BSS selection behaviour. @@ -3837,6 +3879,9 @@ struct cfg80211_cached_keys; * @conn: (private) cfg80211 software SME connection state machine data * @connect_keys: (private) keys to set after connection is established * @conn_bss_type: connecting/connected BSS type + * @conn_owner_nlportid: (private) connection owner socket port ID + * @disconnect_wk: (private) auto-disconnect work + * @disconnect_bssid: (private) the BSSID to use for auto-disconnect * @ibss_fixed: (private) IBSS is using fixed BSSID * @ibss_dfs_possible: (private) IBSS may change to a DFS channel * @event_list: (private) list for internal event processing @@ -3868,6 +3913,10 @@ struct wireless_dev { struct cfg80211_conn *conn; struct cfg80211_cached_keys *connect_keys; enum ieee80211_bss_type conn_bss_type; + u32 conn_owner_nlportid; + + struct work_struct disconnect_wk; + u8 disconnect_bssid[ETH_ALEN]; struct list_head event_list; spinlock_t event_lock; @@ -3955,26 +4004,15 @@ int ieee80211_channel_to_frequency(int chan, enum nl80211_band band); */ int ieee80211_frequency_to_channel(int freq); -/* - * Name indirection necessary because the ieee80211 code also has - * a function named "ieee80211_get_channel", so if you include - * cfg80211's header file you get cfg80211's version, if you try - * to include both header files you'll (rightfully!) get a symbol - * clash. - */ -struct ieee80211_channel *__ieee80211_get_channel(struct wiphy *wiphy, - int freq); /** * ieee80211_get_channel - get channel struct from wiphy for specified frequency + * * @wiphy: the struct wiphy to get the channel for * @freq: the center frequency of the channel + * * Return: The channel struct from @wiphy at @freq. */ -static inline struct ieee80211_channel * -ieee80211_get_channel(struct wiphy *wiphy, int freq) -{ - return __ieee80211_get_channel(wiphy, freq); -} +struct ieee80211_channel *ieee80211_get_channel(struct wiphy *wiphy, int freq); /** * ieee80211_get_response_rate - get basic rate for a given rate @@ -5048,20 +5086,32 @@ static inline void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp) * @req_ie_len: association request IEs length * @resp_ie: association response IEs (may be %NULL) * @resp_ie_len: assoc response IEs length - * @status: status code, 0 for successful connection, use - * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you - * the real status code for failures. + * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use + * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you + * the real status code for failures. If this call is used to report a + * failure due to a timeout (e.g., not receiving an Authentication frame + * from the AP) instead of an explicit rejection by the AP, -1 is used to + * indicate that this is a failure, but without a status code. + * @timeout_reason is used to report the reason for the timeout in that + * case. * @gfp: allocation flags - * - * It should be called by the underlying driver whenever connect() has - * succeeded. This is similar to cfg80211_connect_result(), but with the - * option of identifying the exact bss entry for the connection. Only one of - * these functions should be called. + * @timeout_reason: reason for connection timeout. This is used when the + * connection fails due to a timeout instead of an explicit rejection from + * the AP. %NL80211_TIMEOUT_UNSPECIFIED is used when the timeout reason is + * not known. This value is used only if @status < 0 to indicate that the + * failure is due to a timeout and not due to explicit rejection by the AP. + * This value is ignored in other cases (@status >= 0). + * + * It should be called by the underlying driver once execution of the connection + * request from connect() has been completed. This is similar to + * cfg80211_connect_result(), but with the option of identifying the exact bss + * entry for the connection. Only one of these functions should be called. */ void cfg80211_connect_bss(struct net_device *dev, const u8 *bssid, struct cfg80211_bss *bss, const u8 *req_ie, size_t req_ie_len, const u8 *resp_ie, - size_t resp_ie_len, int status, gfp_t gfp); + size_t resp_ie_len, int status, gfp_t gfp, + enum nl80211_timeout_reason timeout_reason); /** * cfg80211_connect_result - notify cfg80211 of connection result @@ -5072,13 +5122,15 @@ void cfg80211_connect_bss(struct net_device *dev, const u8 *bssid, * @req_ie_len: association request IEs length * @resp_ie: association response IEs (may be %NULL) * @resp_ie_len: assoc response IEs length - * @status: status code, 0 for successful connection, use + * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you * the real status code for failures. * @gfp: allocation flags * - * It should be called by the underlying driver whenever connect() has - * succeeded. + * It should be called by the underlying driver once execution of the connection + * request from connect() has been completed. This is similar to + * cfg80211_connect_bss() which allows the exact bss entry to be specified. Only + * one of these functions should be called. */ static inline void cfg80211_connect_result(struct net_device *dev, const u8 *bssid, @@ -5087,7 +5139,8 @@ cfg80211_connect_result(struct net_device *dev, const u8 *bssid, u16 status, gfp_t gfp) { cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, resp_ie, - resp_ie_len, status, gfp); + resp_ie_len, status, gfp, + NL80211_TIMEOUT_UNSPECIFIED); } /** @@ -5098,6 +5151,7 @@ cfg80211_connect_result(struct net_device *dev, const u8 *bssid, * @req_ie: association request IEs (maybe be %NULL) * @req_ie_len: association request IEs length * @gfp: allocation flags + * @timeout_reason: reason for connection timeout. * * It should be called by the underlying driver whenever connect() has failed * in a sequence where no explicit authentication/association rejection was @@ -5107,10 +5161,11 @@ cfg80211_connect_result(struct net_device *dev, const u8 *bssid, */ static inline void cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid, - const u8 *req_ie, size_t req_ie_len, gfp_t gfp) + const u8 *req_ie, size_t req_ie_len, gfp_t gfp, + enum nl80211_timeout_reason timeout_reason) { cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, NULL, 0, -1, - gfp); + gfp, timeout_reason); } /** |