1 files changed, 19 insertions, 18 deletions

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 52629ca80437..0f616419213c 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -852,19 +852,6 @@ static void imx_break_ctl(struct uart_port *port, int break_state)
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
-#define TXTL 2 /* reset default */
-#define RXTL 1 /* reset default */
-
-static void imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
-{
-	unsigned int val;
-
-	/* set receiver / transmitter trigger level */
-	val = readl(sport->port.membase + UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
-	val |= TXTL << UFCR_TXTL_SHF | RXTL;
-	writel(val, sport->port.membase + UFCR);
-}
-
 #define RX_BUF_SIZE	(PAGE_SIZE)
 static void imx_rx_dma_done(struct imx_port *sport)
 {
@@ -980,6 +967,20 @@ static int start_rx_dma(struct imx_port *sport)
 	return 0;
 }
 
+#define TXTL_DEFAULT 2 /* reset default */
+#define RXTL_DEFAULT 1 /* reset default */
+
+static void imx_setup_ufcr(struct imx_port *sport,
+			  unsigned char txwl, unsigned char rxwl)
+{
+	unsigned int val;
+
+	/* set receiver / transmitter trigger level */
+	val = readl(sport->port.membase + UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
+	val |= txwl << UFCR_TXTL_SHF | rxwl;
+	writel(val, sport->port.membase + UFCR);
+}
+
 static void imx_uart_dma_exit(struct imx_port *sport)
 {
 	if (sport->dma_chan_rx) {
@@ -1015,7 +1016,7 @@ static int imx_uart_dma_init(struct imx_port *sport)
 	slave_config.direction = DMA_DEV_TO_MEM;
 	slave_config.src_addr = sport->port.mapbase + URXD0;
 	slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	slave_config.src_maxburst = RXTL;
+	slave_config.src_maxburst = RXTL_DEFAULT;
 	ret = dmaengine_slave_config(sport->dma_chan_rx, &slave_config);
 	if (ret) {
 		dev_err(dev, "error in RX dma configuration.\n");
@@ -1039,7 +1040,7 @@ static int imx_uart_dma_init(struct imx_port *sport)
 	slave_config.direction = DMA_MEM_TO_DEV;
 	slave_config.dst_addr = sport->port.mapbase + URTX0;
 	slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	slave_config.dst_maxburst = TXTL;
+	slave_config.dst_maxburst = TXTL_DEFAULT;
 	ret = dmaengine_slave_config(sport->dma_chan_tx, &slave_config);
 	if (ret) {
 		dev_err(dev, "error in TX dma configuration.");
@@ -1115,7 +1116,7 @@ static int imx_startup(struct uart_port *port)
 		return retval;
 	}
 
-	imx_setup_ufcr(sport, 0);
+	imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
 
 	/* disable the DREN bit (Data Ready interrupt enable) before
 	 * requesting IRQs
@@ -1503,7 +1504,7 @@ static int imx_poll_init(struct uart_port *port)
 	if (retval)
 		clk_disable_unprepare(sport->clk_ipg);
 
-	imx_setup_ufcr(sport, 0);
+	imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
@@ -1773,7 +1774,7 @@ imx_console_setup(struct console *co, char *options)
 	else
 		imx_console_get_options(sport, &baud, &parity, &bits);
 
-	imx_setup_ufcr(sport, 0);
+	imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
 
 	retval = uart_set_options(&sport->port, co, baud, parity, bits, flow);