diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/8250.c | 109 | ||||
| -rw-r--r-- | drivers/serial/8250_pci.c | 36 | ||||
| -rw-r--r-- | drivers/serial/Kconfig | 25 | ||||
| -rw-r--r-- | drivers/serial/Makefile | 5 | ||||
| -rw-r--r-- | drivers/serial/apbuart.c | 57 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart.h | 6 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_core.c | 19 | ||||
| -rw-r--r-- | drivers/serial/ifx6x60.c | 1406 | ||||
| -rw-r--r-- | drivers/serial/ifx6x60.h | 129 | ||||
| -rw-r--r-- | drivers/serial/mpc52xx_uart.c | 6 | ||||
| -rw-r--r-- | drivers/serial/omap-serial.c | 38 | ||||
| -rw-r--r-- | drivers/serial/pch_uart.c | 1451 | ||||
| -rw-r--r-- | drivers/serial/serial_core.c | 10 | ||||
| -rw-r--r-- | drivers/serial/vt8500_serial.c | 648 |
14 files changed, 3867 insertions, 78 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index ee74c934de89..b25e6e490530 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -454,21 +454,40 @@ static void tsi_serial_out(struct uart_port *p, int offset, int value) writeb(value, p->membase + offset); } +/* Save the LCR value so it can be re-written when a Busy Detect IRQ occurs. */ +static inline void dwapb_save_out_value(struct uart_port *p, int offset, + int value) +{ + struct uart_8250_port *up = + container_of(p, struct uart_8250_port, port); + + if (offset == UART_LCR) + up->lcr = value; +} + +/* Read the IER to ensure any interrupt is cleared before returning from ISR. */ +static inline void dwapb_check_clear_ier(struct uart_port *p, int offset) +{ + if (offset == UART_TX || offset == UART_IER) + p->serial_in(p, UART_IER); +} + static void dwapb_serial_out(struct uart_port *p, int offset, int value) { int save_offset = offset; offset = map_8250_out_reg(p, offset) << p->regshift; - /* Save the LCR value so it can be re-written when a - * Busy Detect interrupt occurs. */ - if (save_offset == UART_LCR) { - struct uart_8250_port *up = (struct uart_8250_port *)p; - up->lcr = value; - } + dwapb_save_out_value(p, save_offset, value); writeb(value, p->membase + offset); - /* Read the IER to ensure any interrupt is cleared before - * returning from ISR. */ - if (save_offset == UART_TX || save_offset == UART_IER) - value = p->serial_in(p, UART_IER); + dwapb_check_clear_ier(p, save_offset); +} + +static void dwapb32_serial_out(struct uart_port *p, int offset, int value) +{ + int save_offset = offset; + offset = map_8250_out_reg(p, offset) << p->regshift; + dwapb_save_out_value(p, save_offset, value); + writel(value, p->membase + offset); + dwapb_check_clear_ier(p, save_offset); } static unsigned int io_serial_in(struct uart_port *p, int offset) @@ -485,7 +504,8 @@ static void io_serial_out(struct uart_port *p, int offset, int value) static void set_io_from_upio(struct uart_port *p) { - struct uart_8250_port *up = (struct uart_8250_port *)p; + struct uart_8250_port *up = + container_of(p, struct uart_8250_port, port); switch (p->iotype) { case UPIO_HUB6: p->serial_in = hub6_serial_in; @@ -518,6 +538,11 @@ static void set_io_from_upio(struct uart_port *p) p->serial_out = dwapb_serial_out; break; + case UPIO_DWAPB32: + p->serial_in = mem32_serial_in; + p->serial_out = dwapb32_serial_out; + break; + default: p->serial_in = io_serial_in; p->serial_out = io_serial_out; @@ -536,6 +561,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value) case UPIO_MEM32: case UPIO_AU: case UPIO_DWAPB: + case UPIO_DWAPB32: p->serial_out(p, offset, value); p->serial_in(p, UART_LCR); /* safe, no side-effects */ break; @@ -1319,7 +1345,8 @@ static inline void __stop_tx(struct uart_8250_port *p) static void serial8250_stop_tx(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); __stop_tx(up); @@ -1336,7 +1363,8 @@ static void transmit_chars(struct uart_8250_port *up); static void serial8250_start_tx(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); if (!(up->ier & UART_IER_THRI)) { up->ier |= UART_IER_THRI; @@ -1364,7 +1392,8 @@ static void serial8250_start_tx(struct uart_port *port) static void serial8250_stop_rx(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); up->ier &= ~UART_IER_RLSI; up->port.read_status_mask &= ~UART_LSR_DR; @@ -1373,7 +1402,8 @@ static void serial8250_stop_rx(struct uart_port *port) static void serial8250_enable_ms(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); /* no MSR capabilities */ if (up->bugs & UART_BUG_NOMSR) @@ -1581,7 +1611,8 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id) handled = 1; end = NULL; - } else if (up->port.iotype == UPIO_DWAPB && + } else if ((up->port.iotype == UPIO_DWAPB || + up->port.iotype == UPIO_DWAPB32) && (iir & UART_IIR_BUSY) == UART_IIR_BUSY) { /* The DesignWare APB UART has an Busy Detect (0x07) * interrupt meaning an LCR write attempt occured while the @@ -1781,7 +1812,8 @@ static void serial8250_backup_timeout(unsigned long data) static unsigned int serial8250_tx_empty(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned long flags; unsigned int lsr; @@ -1795,7 +1827,8 @@ static unsigned int serial8250_tx_empty(struct uart_port *port) static unsigned int serial8250_get_mctrl(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned int status; unsigned int ret; @@ -1815,7 +1848,8 @@ static unsigned int serial8250_get_mctrl(struct uart_port *port) static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned char mcr = 0; if (mctrl & TIOCM_RTS) @@ -1836,7 +1870,8 @@ static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) static void serial8250_break_ctl(struct uart_port *port, int break_state) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned long flags; spin_lock_irqsave(&up->port.lock, flags); @@ -1890,7 +1925,8 @@ static void wait_for_xmitr(struct uart_8250_port *up, int bits) static int serial8250_get_poll_char(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned char lsr = serial_inp(up, UART_LSR); if (!(lsr & UART_LSR_DR)) @@ -1904,7 +1940,8 @@ static void serial8250_put_poll_char(struct uart_port *port, unsigned char c) { unsigned int ier; - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); /* * First save the IER then disable the interrupts @@ -1938,11 +1975,14 @@ static void serial8250_put_poll_char(struct uart_port *port, static int serial8250_startup(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned long flags; unsigned char lsr, iir; int retval; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; up->capabilities = uart_config[up->port.type].flags; up->mcr = 0; @@ -2166,7 +2206,8 @@ dont_test_tx_en: static void serial8250_shutdown(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned long flags; /* @@ -2235,7 +2276,8 @@ void serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); unsigned char cval, fcr = 0; unsigned long flags; unsigned int baud, quot; @@ -2435,7 +2477,8 @@ serial8250_set_ldisc(struct uart_port *port, int new) void serial8250_do_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) { - struct uart_8250_port *p = (struct uart_8250_port *)port; + struct uart_8250_port *p = + container_of(port, struct uart_8250_port, port); serial8250_set_sleep(p, state != 0); } @@ -2476,6 +2519,7 @@ static int serial8250_request_std_resource(struct uart_8250_port *up) case UPIO_MEM32: case UPIO_MEM: case UPIO_DWAPB: + case UPIO_DWAPB32: if (!up->port.mapbase) break; @@ -2513,6 +2557,7 @@ static void serial8250_release_std_resource(struct uart_8250_port *up) case UPIO_MEM32: case UPIO_MEM: case UPIO_DWAPB: + case UPIO_DWAPB32: if (!up->port.mapbase) break; @@ -2566,7 +2611,8 @@ static void serial8250_release_rsa_resource(struct uart_8250_port *up) static void serial8250_release_port(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); serial8250_release_std_resource(up); if (up->port.type == PORT_RSA) @@ -2575,7 +2621,8 @@ static void serial8250_release_port(struct uart_port *port) static int serial8250_request_port(struct uart_port *port) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); int ret = 0; ret = serial8250_request_std_resource(up); @@ -2590,7 +2637,8 @@ static int serial8250_request_port(struct uart_port *port) static void serial8250_config_port(struct uart_port *port, int flags) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); int probeflags = PROBE_ANY; int ret; @@ -2771,7 +2819,8 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev) static void serial8250_console_putchar(struct uart_port *port, int ch) { - struct uart_8250_port *up = (struct uart_8250_port *)port; + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); wait_for_xmitr(up, UART_LSR_THRE); serial_out(up, UART_TX, ch); diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c index 842e3b2a02b1..8b8930f700b5 100644 --- a/drivers/serial/8250_pci.c +++ b/drivers/serial/8250_pci.c @@ -957,6 +957,22 @@ pci_default_setup(struct serial_private *priv, return setup_port(priv, port, bar, offset, board->reg_shift); } +static int +ce4100_serial_setup(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_port *port, int idx) +{ + int ret; + + ret = setup_port(priv, port, 0, 0, board->reg_shift); + port->iotype = UPIO_MEM32; + port->type = PORT_XSCALE; + port->flags = (port->flags | UPF_FIXED_PORT | UPF_FIXED_TYPE); + port->regshift = 2; + + return ret; +} + static int skip_tx_en_setup(struct serial_private *priv, const struct pciserial_board *board, struct uart_port *port, int idx) @@ -981,6 +997,7 @@ static int skip_tx_en_setup(struct serial_private *priv, #define PCI_SUBDEVICE_ID_POCTAL232 0x0308 #define PCI_SUBDEVICE_ID_POCTAL422 0x0408 #define PCI_VENDOR_ID_ADVANTECH 0x13fe +#define PCI_DEVICE_ID_INTEL_CE4100_UART 0x2e66 #define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620 #define PCI_DEVICE_ID_TITAN_200I 0x8028 #define PCI_DEVICE_ID_TITAN_400I 0x8048 @@ -1072,6 +1089,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subdevice = PCI_ANY_ID, .setup = skip_tx_en_setup, }, + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_CE4100_UART, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = ce4100_serial_setup, + }, /* * ITE */ @@ -1592,6 +1616,7 @@ enum pci_board_num_t { pbn_ADDIDATA_PCIe_2_3906250, pbn_ADDIDATA_PCIe_4_3906250, pbn_ADDIDATA_PCIe_8_3906250, + pbn_ce4100_1_115200, }; /* @@ -2281,6 +2306,12 @@ static struct pciserial_board pci_boards[] __devinitdata = { .uart_offset = 0x200, .first_offset = 0x1000, }, + [pbn_ce4100_1_115200] = { + .flags = FL_BASE0, + .num_ports = 1, + .base_baud = 921600, + .reg_shift = 2, + }, }; static const struct pci_device_id softmodem_blacklist[] = { @@ -3765,6 +3796,11 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865, 0xA000, 0x3004, 0, 0, pbn_b0_bt_4_115200 }, + /* Intel CE4100 */ + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CE4100_UART, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, + pbn_ce4100_1_115200 }, + /* * These entries match devices with class COMMUNICATION_SERIAL, diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index aff9dcd051c6..ec3c214598d0 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -1381,6 +1381,16 @@ config SERIAL_MSM_CONSOLE depends on SERIAL_MSM=y select SERIAL_CORE_CONSOLE +config SERIAL_VT8500 + bool "VIA VT8500 on-chip serial port support" + depends on ARM && ARCH_VT8500 + select SERIAL_CORE + +config SERIAL_VT8500_CONSOLE + bool "VIA VT8500 serial console support" + depends on SERIAL_VT8500=y + select SERIAL_CORE_CONSOLE + config SERIAL_NETX tristate "NetX serial port support" depends on ARM && ARCH_NETX @@ -1632,4 +1642,19 @@ config SERIAL_ALTERA_UART_CONSOLE help Enable a Altera UART port to be the system console. +config SERIAL_IFX6X60 + tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)" + depends on GPIOLIB && SPI && EXPERIMENTAL + help + Support for the IFX6x60 modem devices on Intel MID platforms. + +config SERIAL_PCH_UART + tristate "Intel EG20T PCH UART" + depends on PCI && DMADEVICES + select SERIAL_CORE + select PCH_DMA + help + This driver is for PCH(Platform controller Hub) UART of Intel EG20T + which is an IOH(Input/Output Hub) for x86 embedded processor. + Enabling PCH_DMA, this PCH UART works as DMA mode. endmenu diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index c5705765454f..8ea92e9c73b0 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -80,12 +80,15 @@ obj-$(CONFIG_SERIAL_NETX) += netx-serial.o obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o +obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o obj-$(CONFIG_SERIAL_QE) += ucc_uart.o obj-$(CONFIG_SERIAL_TIMBERDALE) += timbuart.o obj-$(CONFIG_SERIAL_GRLIB_GAISLER_APBUART) += apbuart.o obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o +obj-$(CONFIG_SERIAL_VT8500) += vt8500_serial.o obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o obj-$(CONFIG_SERIAL_MFD_HSU) += mfd.o -obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o +obj-$(CONFIG_SERIAL_IFX6X60) += ifx6x60.o +obj-$(CONFIG_SERIAL_PCH_UART) += pch_uart.o diff --git a/drivers/serial/apbuart.c b/drivers/serial/apbuart.c index 767ce9e396c5..095a5d562618 100644 --- a/drivers/serial/apbuart.c +++ b/drivers/serial/apbuart.c @@ -521,11 +521,12 @@ static struct console grlib_apbuart_console = { }; -static void grlib_apbuart_configure(void); +static int grlib_apbuart_configure(void); static int __init apbuart_console_init(void) { - grlib_apbuart_configure(); + if (grlib_apbuart_configure()) + return -ENODEV; register_console(&grlib_apbuart_console); return 0; } @@ -596,57 +597,49 @@ static struct of_platform_driver grlib_apbuart_of_driver = { }; -static void grlib_apbuart_configure(void) +static int grlib_apbuart_configure(void) { - static int enum_done; struct device_node *np, *rp; - struct uart_port *port = NULL; const u32 *prop; - int freq_khz; - int v = 0, d = 0; - unsigned int addr; - int irq, line; - struct amba_prom_registers *regs; - - if (enum_done) - return; + int freq_khz, line = 0; /* Get bus frequency */ rp = of_find_node_by_path("/"); + if (!rp) + return -ENODEV; rp = of_get_next_child(rp, NULL); + if (!rp) + return -ENODEV; prop = of_get_property(rp, "clock-frequency", NULL); + if (!prop) + return -ENODEV; freq_khz = *prop; - line = 0; for_each_matching_node(np, apbuart_match) { + const int *irqs, *ampopts; + const struct amba_prom_registers *regs; + struct uart_port *port; + unsigned long addr; - int *vendor = (int *) of_get_property(np, "vendor", NULL); - int *device = (int *) of_get_property(np, "device", NULL); - int *irqs = (int *) of_get_property(np, "interrupts", NULL); - int *ampopts = (int *) of_get_property(np, "ampopts", NULL); - regs = (struct amba_prom_registers *) - of_get_property(np, "reg", NULL); - + ampopts = of_get_property(np, "ampopts", NULL); if (ampopts && (*ampopts == 0)) continue; /* Ignore if used by another OS instance */ - if (vendor) - v = *vendor; - if (device) - d = *device; + + irqs = of_get_property(np, "interrupts", NULL); + regs = of_get_property(np, "reg", NULL); if (!irqs || !regs) - return; + continue; grlib_apbuart_nodes[line] = np; addr = regs->phys_addr; - irq = *irqs; port = &grlib_apbuart_ports[line]; port->mapbase = addr; port->membase = ioremap(addr, sizeof(struct grlib_apbuart_regs_map)); - port->irq = irq; + port->irq = *irqs; port->iotype = UPIO_MEM; port->ops = &grlib_apbuart_ops; port->flags = UPF_BOOT_AUTOCONF; @@ -658,12 +651,10 @@ static void grlib_apbuart_configure(void) /* We support maximum UART_NR uarts ... */ if (line == UART_NR) break; - } - enum_done = 1; - grlib_apbuart_driver.nr = grlib_apbuart_port_nr = line; + return line ? 0 : -ENODEV; } static int __init grlib_apbuart_init(void) @@ -671,7 +662,9 @@ static int __init grlib_apbuart_init(void) int ret; /* Find all APBUARTS in device the tree and initialize their ports */ - grlib_apbuart_configure(); + ret = grlib_apbuart_configure(); + if (ret) + return ret; printk(KERN_INFO "Serial: GRLIB APBUART driver\n"); diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h index 7274b527a3c1..b754dcf0fda5 100644 --- a/drivers/serial/cpm_uart/cpm_uart.h +++ b/drivers/serial/cpm_uart/cpm_uart.h @@ -76,18 +76,12 @@ struct uart_cpm_port { unsigned char *tx_buf; unsigned char *rx_buf; u32 flags; - void (*set_lineif)(struct uart_cpm_port *); struct clk *clk; u8 brg; uint dp_addr; void *mem_addr; dma_addr_t dma_addr; u32 mem_size; - /* helpers */ - int baud; - int bits; - /* Keep track of 'odd' SMC2 wirings */ - int is_portb; /* wait on close if needed */ int wait_closing; /* value to combine with opcode to form cpm command */ diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index f2b8adcc6c92..8692ff98fc07 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -72,6 +72,8 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo); /**************************************************************/ +#define HW_BUF_SPD_THRESHOLD 9600 + /* * Check, if transmit buffers are processed */ @@ -503,6 +505,11 @@ static void cpm_uart_set_termios(struct uart_port *port, pr_debug("CPM uart[%d]:set_termios\n", port->line); baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + if (baud <= HW_BUF_SPD_THRESHOLD || + (pinfo->port.state && pinfo->port.state->port.tty->low_latency)) + pinfo->rx_fifosize = 1; + else + pinfo->rx_fifosize = RX_BUF_SIZE; /* Character length programmed into the mode register is the * sum of: 1 start bit, number of data bits, 0 or 1 parity bit, @@ -594,6 +601,17 @@ static void cpm_uart_set_termios(struct uart_port *port, */ bits++; if (IS_SMC(pinfo)) { + /* + * MRBLR can be changed while an SMC/SCC is operating only + * if it is done in a single bus cycle with one 16-bit move + * (not two 8-bit bus cycles back-to-back). This occurs when + * the cp shifts control to the next RxBD, so the change does + * not take effect immediately. To guarantee the exact RxBD + * on which the change occurs, change MRBLR only while the + * SMC/SCC receiver is disabled. + */ + out_be16(&pinfo->smcup->smc_mrblr, pinfo->rx_fifosize); + /* Set the mode register. We want to keep a copy of the * enables, because we want to put them back if they were * present. @@ -604,6 +622,7 @@ static void cpm_uart_set_termios(struct uart_port *port, out_be16(&smcp->smc_smcmr, smcr_mk_clen(bits) | cval | SMCMR_SM_UART | prev_mode); } else { + out_be16(&pinfo->sccup->scc_genscc.scc_mrblr, pinfo->rx_fifosize); out_be16(&sccp->scc_psmr, (sbits << 12) | scval); } diff --git a/drivers/serial/ifx6x60.c b/drivers/serial/ifx6x60.c new file mode 100644 index 000000000000..ab93763862d5 --- /dev/null +++ b/drivers/serial/ifx6x60.c @@ -0,0 +1,1406 @@ +/**************************************************************************** + * + * Driver for the IFX 6x60 spi modem. + * + * Copyright (C) 2008 Option International + * Copyright (C) 2008 Filip Aben <f.aben@option.com> + * Denis Joseph Barrow <d.barow@option.com> + * Jan Dumon <j.dumon@option.com> + * + * Copyright (C) 2009, 2010 Intel Corp + * Russ Gorby <richardx.r.gorby@intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, + * USA + * + * Driver modified by Intel from Option gtm501l_spi.c + * + * Notes + * o The driver currently assumes a single device only. If you need to + * change this then look for saved_ifx_dev and add a device lookup + * o The driver is intended to be big-endian safe but has never been + * tested that way (no suitable hardware). There are a couple of FIXME + * notes by areas that may need addressing + * o Some of the GPIO naming/setup assumptions may need revisiting if + * you need to use this driver for another platform. + * + *****************************************************************************/ +#include <linux/module.h> +#include <linux/termios.h> +#include <linux/tty.h> +#include <linux/device.h> +#include <linux/spi/spi.h> +#include <linux/tty.h> +#include <linux/kfifo.h> +#include <linux/tty_flip.h> +#include <linux/timer.h> +#include <linux/serial.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/rfkill.h> +#include <linux/fs.h> +#include <linux/ip.h> +#include <linux/dmapool.h> +#include <linux/gpio.h> +#include <linux/sched.h> +#include <linux/time.h> +#include <linux/wait.h> +#include <linux/tty.h> +#include <linux/pm.h> +#include <linux/pm_runtime.h> +#include <linux/spi/ifx_modem.h> +#include <linux/delay.h> + +#include "ifx6x60.h" + +#define IFX_SPI_MORE_MASK 0x10 +#define IFX_SPI_MORE_BIT 12 /* bit position in u16 */ +#define IFX_SPI_CTS_BIT 13 /* bit position in u16 */ +#define IFX_SPI_TTY_ID 0 +#define IFX_SPI_TIMEOUT_SEC 2 +#define IFX_SPI_HEADER_0 (-1) +#define IFX_SPI_HEADER_F (-2) + +/* forward reference */ +static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev); + +/* local variables */ +static int spi_b16 = 1; /* 8 or 16 bit word length */ +static struct tty_driver *tty_drv; +static struct ifx_spi_device *saved_ifx_dev; +static struct lock_class_key ifx_spi_key; + +/* GPIO/GPE settings */ + +/** + * mrdy_set_high - set MRDY GPIO + * @ifx: device we are controlling + * + */ +static inline void mrdy_set_high(struct ifx_spi_device *ifx) +{ + gpio_set_value(ifx->gpio.mrdy, 1); +} + +/** + * mrdy_set_low - clear MRDY GPIO + * @ifx: device we are controlling + * + */ +static inline void mrdy_set_low(struct ifx_spi_device *ifx) +{ + gpio_set_value(ifx->gpio.mrdy, 0); +} + +/** + * ifx_spi_power_state_set + * @ifx_dev: our SPI device + * @val: bits to set + * + * Set bit in power status and signal power system if status becomes non-0 + */ +static void +ifx_spi_power_state_set(struct ifx_spi_device *ifx_dev, unsigned char val) +{ + unsigned long flags; + + spin_lock_irqsave(&ifx_dev->power_lock, flags); + + /* + * if power status is already non-0, just update, else + * tell power system + */ + if (!ifx_dev->power_status) + pm_runtime_get(&ifx_dev->spi_dev->dev); + ifx_dev->power_status |= val; + + spin_unlock_irqrestore(&ifx_dev->power_lock, flags); +} + +/** + * ifx_spi_power_state_clear - clear power bit + * @ifx_dev: our SPI device + * @val: bits to clear + * + * clear bit in power status and signal power system if status becomes 0 + */ +static void +ifx_spi_power_state_clear(struct ifx_spi_device *ifx_dev, unsigned char val) +{ + unsigned long flags; + + spin_lock_irqsave(&ifx_dev->power_lock, flags); + + if (ifx_dev->power_status) { + ifx_dev->power_status &= ~val; + if (!ifx_dev->power_status) + pm_runtime_put(&ifx_dev->spi_dev->dev); + } + + spin_unlock_irqrestore(&ifx_dev->power_lock, flags); +} + +/** + * swap_buf + * @buf: our buffer + * @len : number of bytes (not words) in the buffer + * @end: end of buffer + * + * Swap the contents of a buffer into big endian format + */ +static inline void swap_buf(u16 *buf, int len, void *end) +{ + int n; + + len = ((len + 1) >> 1); + if ((void *)&buf[len] > end) { + pr_err("swap_buf: swap exceeds boundary (%p > %p)!", + &buf[len], end); + return; + } + for (n = 0; n < len; n++) { + *buf = cpu_to_be16(*buf); + buf++; + } +} + +/** + * mrdy_assert - assert MRDY line + * @ifx_dev: our SPI device + * + * Assert mrdy and set timer to wait for SRDY interrupt, if SRDY is low + * now. + * + * FIXME: Can SRDY even go high as we are running this code ? + */ +static void mrdy_assert(struct ifx_spi_device *ifx_dev) +{ + int val = gpio_get_value(ifx_dev->gpio.srdy); + if (!val) { + if (!test_and_set_bit(IFX_SPI_STATE_TIMER_PENDING, + &ifx_dev->flags)) { + ifx_dev->spi_timer.expires = + jiffies + IFX_SPI_TIMEOUT_SEC*HZ; + add_timer(&ifx_dev->spi_timer); + + } + } + ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_DATA_PENDING); + mrdy_set_high(ifx_dev); +} + +/** + * ifx_spi_hangup - hang up an IFX device + * @ifx_dev: our SPI device + * + * Hang up the tty attached to the IFX device if one is currently + * open. If not take no action + */ +static void ifx_spi_ttyhangup(struct ifx_spi_device *ifx_dev) +{ + struct tty_port *pport = &ifx_dev->tty_port; + struct tty_struct *tty = tty_port_tty_get(pport); + if (tty) { + tty_hangup(tty); + tty_kref_put(tty); + } +} + +/** + * ifx_spi_timeout - SPI timeout + * @arg: our SPI device + * + * The SPI has timed out: hang up the tty. Users will then see a hangup + * and error events. + */ +static void ifx_spi_timeout(unsigned long arg) +{ + struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *)arg; + + dev_warn(&ifx_dev->spi_dev->dev, "*** SPI Timeout ***"); + ifx_spi_ttyhangup(ifx_dev); + mrdy_set_low(ifx_dev); + clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags); +} + +/* char/tty operations */ + +/** + * ifx_spi_tiocmget - get modem lines + * @tty: our tty device + * @filp: file handle issuing the request + * + * Map the signal state into Linux modem flags and report the value + * in Linux terms + */ +static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp) +{ + unsigned int value; + struct ifx_spi_device *ifx_dev = tty->driver_data; + + value = + (test_bit(IFX_SPI_RTS, &ifx_dev->signal_state) ? TIOCM_RTS : 0) | + (test_bit(IFX_SPI_DTR, &ifx_dev->signal_state) ? TIOCM_DTR : 0) | + (test_bit(IFX_SPI_CTS, &ifx_dev->signal_state) ? TIOCM_CTS : 0) | + (test_bit(IFX_SPI_DSR, &ifx_dev->signal_state) ? TIOCM_DSR : 0) | + (test_bit(IFX_SPI_DCD, &ifx_dev->signal_state) ? TIOCM_CAR : 0) | + (test_bit(IFX_SPI_RI, &ifx_dev->signal_state) ? TIOCM_RNG : 0); + return value; +} + +/** + * ifx_spi_tiocmset - set modem bits + * @tty: the tty structure + * @filp: file handle issuing the request + * @set: bits to set + * @clear: bits to clear + * + * The IFX6x60 only supports DTR and RTS. Set them accordingly + * and flag that an update to the modem is needed. + * + * FIXME: do we need to kick the tranfers when we do this ? + */ +static int ifx_spi_tiocmset(struct tty_struct *tty, struct file *filp, + unsigned int set, unsigned int clear) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + + if (set & TIOCM_RTS) + set_bit(IFX_SPI_RTS, &ifx_dev->signal_state); + if (set & TIOCM_DTR) + set_bit(IFX_SPI_DTR, &ifx_dev->signal_state); + if (clear & TIOCM_RTS) + clear_bit(IFX_SPI_RTS, &ifx_dev->signal_state); + if (clear & TIOCM_DTR) + clear_bit(IFX_SPI_DTR, &ifx_dev->signal_state); + + set_bit(IFX_SPI_UPDATE, &ifx_dev->signal_state); + return 0; +} + +/** + * ifx_spi_open - called on tty open + * @tty: our tty device + * @filp: file handle being associated with the tty + * + * Open the tty interface. We let the tty_port layer do all the work + * for us. + * + * FIXME: Remove single device assumption and saved_ifx_dev + */ +static int ifx_spi_open(struct tty_struct *tty, struct file *filp) +{ + return tty_port_open(&saved_ifx_dev->tty_port, tty, filp); +} + +/** + * ifx_spi_close - called when our tty closes + * @tty: the tty being closed + * @filp: the file handle being closed + * + * Perform the close of the tty. We use the tty_port layer to do all + * our hard work. + */ +static void ifx_spi_close(struct tty_struct *tty, struct file *filp) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + tty_port_close(&ifx_dev->tty_port, tty, filp); + /* FIXME: should we do an ifx_spi_reset here ? */ +} + +/** + * ifx_decode_spi_header - decode received header + * @buffer: the received data + * @length: decoded length + * @more: decoded more flag + * @received_cts: status of cts we received + * + * Note how received_cts is handled -- if header is all F it is left + * the same as it was, if header is all 0 it is set to 0 otherwise it is + * taken from the incoming header. + * + * FIXME: endianness + */ +static int ifx_spi_decode_spi_header(unsigned char *buffer, int *length, + unsigned char *more, unsigned char *received_cts) +{ + u16 h1; + u16 h2; + u16 *in_buffer = (u16 *)buffer; + + h1 = *in_buffer; + h2 = *(in_buffer+1); + + if (h1 == 0 && h2 == 0) { + *received_cts = 0; + return IFX_SPI_HEADER_0; + } else if (h1 == 0xffff && h2 == 0xffff) { + /* spi_slave_cts remains as it was */ + return IFX_SPI_HEADER_F; + } + + *length = h1 & 0xfff; /* upper bits of byte are flags */ + *more = (buffer[1] >> IFX_SPI_MORE_BIT) & 1; + *received_cts = (buffer[3] >> IFX_SPI_CTS_BIT) & 1; + return 0; +} + +/** + * ifx_setup_spi_header - set header fields + * @txbuffer: pointer to start of SPI buffer + * @tx_count: bytes + * @more: indicate if more to follow + * + * Format up an SPI header for a transfer + * + * FIXME: endianness? + */ +static void ifx_spi_setup_spi_header(unsigned char *txbuffer, int tx_count, + unsigned char more) +{ + *(u16 *)(txbuffer) = tx_count; + *(u16 *)(txbuffer+2) = IFX_SPI_PAYLOAD_SIZE; + txbuffer[1] |= (more << IFX_SPI_MORE_BIT) & IFX_SPI_MORE_MASK; +} + +/** + * ifx_spi_wakeup_serial - SPI space made + * @port_data: our SPI device + * + * We have emptied the FIFO enough that we want to get more data + * queued into it. Poke the line discipline via tty_wakeup so that + * it will feed us more bits + */ +static void ifx_spi_wakeup_serial(struct ifx_spi_device *ifx_dev) +{ + struct tty_struct *tty; + + tty = tty_port_tty_get(&ifx_dev->tty_port); + if (!tty) + return; + tty_wakeup(tty); + tty_kref_put(tty); +} + +/** + * ifx_spi_prepare_tx_buffer - prepare transmit frame + * @ifx_dev: our SPI device + * + * The transmit buffr needs a header and various other bits of + * information followed by as much data as we can pull from the FIFO + * and transfer. This function formats up a suitable buffer in the + * ifx_dev->tx_buffer + * + * FIXME: performance - should we wake the tty when the queue is half + * empty ? + */ +static int ifx_spi_prepare_tx_buffer(struct ifx_spi_device *ifx_dev) +{ + int temp_count; + int queue_length; + int tx_count; + unsigned char *tx_buffer; + + tx_buffer = ifx_dev->tx_buffer; + memset(tx_buffer, 0, IFX_SPI_TRANSFER_SIZE); + + /* make room for required SPI header */ + tx_buffer += IFX_SPI_HEADER_OVERHEAD; + tx_count = IFX_SPI_HEADER_OVERHEAD; + + /* clear to signal no more data if this turns out to be the + * last buffer sent in a sequence */ + ifx_dev->spi_more = 0; + + /* if modem cts is set, just send empty buffer */ + if (!ifx_dev->spi_slave_cts) { + /* see if there's tx data */ + queue_length = kfifo_len(&ifx_dev->tx_fifo); + if (queue_length != 0) { + /* data to mux -- see if there's room for it */ + temp_count = min(queue_length, IFX_SPI_PAYLOAD_SIZE); + temp_count = kfifo_out_locked(&ifx_dev->tx_fifo, + tx_buffer, temp_count, + &ifx_dev->fifo_lock); + + /* update buffer pointer and data count in message */ + tx_buffer += temp_count; + tx_count += temp_count; + if (temp_count == queue_length) + /* poke port to get more data */ + ifx_spi_wakeup_serial(ifx_dev); + else /* more data in port, use next SPI message */ + ifx_dev->spi_more = 1; + } + } + /* have data and info for header -- set up SPI header in buffer */ + /* spi header needs payload size, not entire buffer size */ + ifx_spi_setup_spi_header(ifx_dev->tx_buffer, + tx_count-IFX_SPI_HEADER_OVERHEAD, + ifx_dev->spi_more); + /* swap actual data in the buffer */ + swap_buf((u16 *)(ifx_dev->tx_buffer), tx_count, + &ifx_dev->tx_buffer[IFX_SPI_TRANSFER_SIZE]); + return tx_count; +} + +/** + * ifx_spi_write - line discipline write + * @tty: our tty device + * @buf: pointer to buffer to write (kernel space) + * @count: size of buffer + * + * Write the characters we have been given into the FIFO. If the device + * is not active then activate it, when the SRDY line is asserted back + * this will commence I/O + */ +static int ifx_spi_write(struct tty_struct *tty, const unsigned char *buf, + int count) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + unsigned char *tmp_buf = (unsigned char *)buf; + int tx_count = kfifo_in_locked(&ifx_dev->tx_fifo, tmp_buf, count, + &ifx_dev->fifo_lock); + mrdy_assert(ifx_dev); + return tx_count; +} + +/** + * ifx_spi_chars_in_buffer - line discipline helper + * @tty: our tty device + * + * Report how much data we can accept before we drop bytes. As we use + * a simple FIFO this is nice and easy. + */ +static int ifx_spi_write_room(struct tty_struct *tty) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + return IFX_SPI_FIFO_SIZE - kfifo_len(&ifx_dev->tx_fifo); +} + +/** + * ifx_spi_chars_in_buffer - line discipline helper + * @tty: our tty device + * + * Report how many characters we have buffered. In our case this is the + * number of bytes sitting in our transmit FIFO. + */ +static int ifx_spi_chars_in_buffer(struct tty_struct *tty) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + return kfifo_len(&ifx_dev->tx_fifo); +} + +/** + * ifx_port_hangup + * @port: our tty port + * + * tty port hang up. Called when tty_hangup processing is invoked either + * by loss of carrier, or by software (eg vhangup). Serialized against + * activate/shutdown by the tty layer. + */ +static void ifx_spi_hangup(struct tty_struct *tty) +{ + struct ifx_spi_device *ifx_dev = tty->driver_data; + tty_port_hangup(&ifx_dev->tty_port); +} + +/** + * ifx_port_activate + * @port: our tty port + * + * tty port activate method - called for first open. Serialized + * with hangup and shutdown by the tty layer. + */ +static int ifx_port_activate(struct tty_port *port, struct tty_struct *tty) +{ + struct ifx_spi_device *ifx_dev = + container_of(port, struct ifx_spi_device, tty_port); + + /* clear any old data; can't do this in 'close' */ + kfifo_reset(&ifx_dev->tx_fifo); + + /* put port data into this tty */ + tty->driver_data = ifx_dev; + + /* allows flip string push from int context */ + tty->low_latency = 1; + + return 0; +} + +/** + * ifx_port_shutdown + * @port: our tty port + * + * tty port shutdown method - called for last port close. Serialized + * with hangup and activate by the tty layer. + */ +static void ifx_port_shutdown(struct tty_port *port) +{ + struct ifx_spi_device *ifx_dev = + container_of(port, struct ifx_spi_device, tty_port); + + mrdy_set_low(ifx_dev); + clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags); + tasklet_kill(&ifx_dev->io_work_tasklet); +} + +static const struct tty_port_operations ifx_tty_port_ops = { + .activate = ifx_port_activate, + .shutdown = ifx_port_shutdown, +}; + +static const struct tty_operations ifx_spi_serial_ops = { + .open = ifx_spi_open, + .close = ifx_spi_close, + .write = ifx_spi_write, + .hangup = ifx_spi_hangup, + .write_room = ifx_spi_write_room, + .chars_in_buffer = ifx_spi_chars_in_buffer, + .tiocmget = ifx_spi_tiocmget, + .tiocmset = ifx_spi_tiocmset, +}; + +/** + * ifx_spi_insert_fip_string - queue received data + * @ifx_ser: our SPI device + * @chars: buffer we have received + * @size: number of chars reeived + * + * Queue bytes to the tty assuming the tty side is currently open. If + * not the discard the data. + */ +static void ifx_spi_insert_flip_string(struct ifx_spi_device *ifx_dev, + unsigned char *chars, size_t size) +{ + struct tty_struct *tty = tty_port_tty_get(&ifx_dev->tty_port); + if (!tty) + return; + tty_insert_flip_string(tty, chars, size); + tty_flip_buffer_push(tty); + tty_kref_put(tty); +} + +/** + * ifx_spi_complete - SPI transfer completed + * @ctx: our SPI device + * + * An SPI transfer has completed. Process any received data and kick off + * any further transmits we can commence. + */ +static void ifx_spi_complete(void *ctx) +{ + struct ifx_spi_device *ifx_dev = ctx; + struct tty_struct *tty; + struct tty_ldisc *ldisc = NULL; + int length; + int actual_length; + unsigned char more; + unsigned char cts; + int local_write_pending = 0; + int queue_length; + int srdy; + int decode_result; + + mrdy_set_low(ifx_dev); + + if (!ifx_dev->spi_msg.status) { + /* check header validity, get comm flags */ + swap_buf((u16 *)ifx_dev->rx_buffer, IFX_SPI_HEADER_OVERHEAD, + &ifx_dev->rx_buffer[IFX_SPI_HEADER_OVERHEAD]); + decode_result = ifx_spi_decode_spi_header(ifx_dev->rx_buffer, + &length, &more, &cts); + if (decode_result == IFX_SPI_HEADER_0) { + dev_dbg(&ifx_dev->spi_dev->dev, + "ignore input: invalid header 0"); + ifx_dev->spi_slave_cts = 0; + goto complete_exit; + } else if (decode_result == IFX_SPI_HEADER_F) { + dev_dbg(&ifx_dev->spi_dev->dev, + "ignore input: invalid header F"); + goto complete_exit; + } + + ifx_dev->spi_slave_cts = cts; + + actual_length = min((unsigned int)length, + ifx_dev->spi_msg.actual_length); + swap_buf((u16 *)(ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD), + actual_length, + &ifx_dev->rx_buffer[IFX_SPI_TRANSFER_SIZE]); + ifx_spi_insert_flip_string( + ifx_dev, + ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD, + (size_t)actual_length); + } else { + dev_dbg(&ifx_dev->spi_dev->dev, "SPI transfer error %d", + ifx_dev->spi_msg.status); + } + +complete_exit: + if (ifx_dev->write_pending) { + ifx_dev->write_pending = 0; + local_write_pending = 1; + } + + clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &(ifx_dev->flags)); + + queue_length = kfifo_len(&ifx_dev->tx_fifo); + srdy = gpio_get_value(ifx_dev->gpio.srdy); + if (!srdy) + ifx_spi_power_state_clear(ifx_dev, IFX_SPI_POWER_SRDY); + + /* schedule output if there is more to do */ + if (test_and_clear_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags)) + tasklet_schedule(&ifx_dev->io_work_tasklet); + else { + if (more || ifx_dev->spi_more || queue_length > 0 || + local_write_pending) { + if (ifx_dev->spi_slave_cts) { + if (more) + mrdy_assert(ifx_dev); + } else + mrdy_assert(ifx_dev); + } else { + /* + * poke line discipline driver if any for more data + * may or may not get more data to write + * for now, say not busy + */ + ifx_spi_power_state_clear(ifx_dev, + IFX_SPI_POWER_DATA_PENDING); + tty = tty_port_tty_get(&ifx_dev->tty_port); + if (tty) { + ldisc = tty_ldisc_ref(tty); + if (ldisc) { + ldisc->ops->write_wakeup(tty); + tty_ldisc_deref(ldisc); + } + tty_kref_put(tty); + } + } + } +} + +/** + * ifx_spio_io - I/O tasklet + * @data: our SPI device + * + * Queue data for transmission if possible and then kick off the + * transfer. + */ +static void ifx_spi_io(unsigned long data) +{ + int retval; + struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *) data; + + if (!test_and_set_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags)) { + if (ifx_dev->gpio.unack_srdy_int_nb > 0) + ifx_dev->gpio.unack_srdy_int_nb--; + + ifx_spi_prepare_tx_buffer(ifx_dev); + + spi_message_init(&ifx_dev->spi_msg); + INIT_LIST_HEAD(&ifx_dev->spi_msg.queue); + + ifx_dev->spi_msg.context = ifx_dev; + ifx_dev->spi_msg.complete = ifx_spi_complete; + + /* set up our spi transfer */ + /* note len is BYTES, not transfers */ + ifx_dev->spi_xfer.len = IFX_SPI_TRANSFER_SIZE; + ifx_dev->spi_xfer.cs_change = 0; + ifx_dev->spi_xfer.speed_hz = 12500000; + /* ifx_dev->spi_xfer.speed_hz = 390625; */ + ifx_dev->spi_xfer.bits_per_word = spi_b16 ? 16 : 8; + + ifx_dev->spi_xfer.tx_buf = ifx_dev->tx_buffer; + ifx_dev->spi_xfer.rx_buf = ifx_dev->rx_buffer; + + /* + * setup dma pointers + */ + if (ifx_dev->is_6160) { + ifx_dev->spi_msg.is_dma_mapped = 1; + ifx_dev->tx_dma = ifx_dev->tx_bus; + ifx_dev->rx_dma = ifx_dev->rx_bus; + ifx_dev->spi_xfer.tx_dma = ifx_dev->tx_dma; + ifx_dev->spi_xfer.rx_dma = ifx_dev->rx_dma; + } else { + ifx_dev->spi_msg.is_dma_mapped = 0; + ifx_dev->tx_dma = (dma_addr_t)0; + ifx_dev->rx_dma = (dma_addr_t)0; + ifx_dev->spi_xfer.tx_dma = (dma_addr_t)0; + ifx_dev->spi_xfer.rx_dma = (dma_addr_t)0; + } + + spi_message_add_tail(&ifx_dev->spi_xfer, &ifx_dev->spi_msg); + + /* Assert MRDY. This may have already been done by the write + * routine. + */ + mrdy_assert(ifx_dev); + + retval = spi_async(ifx_dev->spi_dev, &ifx_dev->spi_msg); + if (retval) { + clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, + &ifx_dev->flags); + tasklet_schedule(&ifx_dev->io_work_tasklet); + return; + } + } else + ifx_dev->write_pending = 1; +} + +/** + * ifx_spi_free_port - free up the tty side + * @ifx_dev: IFX device going away + * + * Unregister and free up a port when the device goes away + */ +static void ifx_spi_free_port(struct ifx_spi_device *ifx_dev) +{ + if (ifx_dev->tty_dev) + tty_unregister_device(tty_drv, ifx_dev->minor); + kfifo_free(&ifx_dev->tx_fifo); +} + +/** + * ifx_spi_create_port - create a new port + * @ifx_dev: our spi device + * + * Allocate and initialise the tty port that goes with this interface + * and add it to the tty layer so that it can be opened. + */ +static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev) +{ + int ret = 0; + struct tty_port *pport = &ifx_dev->tty_port; + + spin_lock_init(&ifx_dev->fifo_lock); + lockdep_set_class_and_subclass(&ifx_dev->fifo_lock, + &ifx_spi_key, 0); + + if (kfifo_alloc(&ifx_dev->tx_fifo, IFX_SPI_FIFO_SIZE, GFP_KERNEL)) { + ret = -ENOMEM; + goto error_ret; + } + + pport->ops = &ifx_tty_port_ops; + tty_port_init(pport); + ifx_dev->minor = IFX_SPI_TTY_ID; + ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor, + &ifx_dev->spi_dev->dev); + if (IS_ERR(ifx_dev->tty_dev)) { + dev_dbg(&ifx_dev->spi_dev->dev, + "%s: registering tty device failed", __func__); + ret = PTR_ERR(ifx_dev->tty_dev); + goto error_ret; + } + return 0; + +error_ret: + ifx_spi_free_port(ifx_dev); + return ret; +} + +/** + * ifx_spi_handle_srdy - handle SRDY + * @ifx_dev: device asserting SRDY + * + * Check our device state and see what we need to kick off when SRDY + * is asserted. This usually means killing the timer and firing off the + * I/O processing. + */ +static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev) +{ + if (test_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags)) { + del_timer_sync(&ifx_dev->spi_timer); + clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags); + } + + ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_SRDY); + + if (!test_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags)) + tasklet_schedule(&ifx_dev->io_work_tasklet); + else + set_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags); +} + +/** + * ifx_spi_srdy_interrupt - SRDY asserted + * @irq: our IRQ number + * @dev: our ifx device + * + * The modem asserted SRDY. Handle the srdy event + */ +static irqreturn_t ifx_spi_srdy_interrupt(int irq, void *dev) +{ + struct ifx_spi_device *ifx_dev = dev; + ifx_dev->gpio.unack_srdy_int_nb++; + ifx_spi_handle_srdy(ifx_dev); + return IRQ_HANDLED; +} + +/** + * ifx_spi_reset_interrupt - Modem has changed reset state + * @irq: interrupt number + * @dev: our device pointer + * + * The modem has either entered or left reset state. Check the GPIO + * line to see which. + * + * FIXME: review locking on MR_INPROGRESS versus + * parallel unsolicited reset/solicited reset + */ +static irqreturn_t ifx_spi_reset_interrupt(int irq, void *dev) +{ + struct ifx_spi_device *ifx_dev = dev; + int val = gpio_get_value(ifx_dev->gpio.reset_out); + int solreset = test_bit(MR_START, &ifx_dev->mdm_reset_state); + + if (val == 0) { + /* entered reset */ + set_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state); + if (!solreset) { + /* unsolicited reset */ + ifx_spi_ttyhangup(ifx_dev); + } + } else { + /* exited reset */ + clear_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state); + if (solreset) { + set_bit(MR_COMPLETE, &ifx_dev->mdm_reset_state); + wake_up(&ifx_dev->mdm_reset_wait); + } + } + return IRQ_HANDLED; +} + +/** + * ifx_spi_free_device - free device + * @ifx_dev: device to free + * + * Free the IFX device + */ +static void ifx_spi_free_device(struct ifx_spi_device *ifx_dev) +{ + ifx_spi_free_port(ifx_dev); + dma_free_coherent(&ifx_dev->spi_dev->dev, + IFX_SPI_TRANSFER_SIZE, + ifx_dev->tx_buffer, + ifx_dev->tx_bus); + dma_free_coherent(&ifx_dev->spi_dev->dev, + IFX_SPI_TRANSFER_SIZE, + ifx_dev->rx_buffer, + ifx_dev->rx_bus); +} + +/** + * ifx_spi_reset - reset modem + * @ifx_dev: modem to reset + * + * Perform a reset on the modem + */ +static int ifx_spi_reset(struct ifx_spi_device *ifx_dev) +{ + int ret; + /* + * set up modem power, reset + * + * delays are required on some platforms for the modem + * to reset properly + */ + set_bit(MR_START, &ifx_dev->mdm_reset_state); + gpio_set_value(ifx_dev->gpio.po, 0); + gpio_set_value(ifx_dev->gpio.reset, 0); + msleep(25); + gpio_set_value(ifx_dev->gpio.reset, 1); + msleep(1); + gpio_set_value(ifx_dev->gpio.po, 1); + msleep(1); + gpio_set_value(ifx_dev->gpio.po, 0); + ret = wait_event_timeout(ifx_dev->mdm_reset_wait, + test_bit(MR_COMPLETE, + &ifx_dev->mdm_reset_state), + IFX_RESET_TIMEOUT); + if (!ret) + dev_warn(&ifx_dev->spi_dev->dev, "Modem reset timeout: (state:%lx)", + ifx_dev->mdm_reset_state); + + ifx_dev->mdm_reset_state = 0; + return ret; +} + +/** + * ifx_spi_spi_probe - probe callback + * @spi: our possible matching SPI device + * + * Probe for a 6x60 modem on SPI bus. Perform any needed device and + * GPIO setup. + * + * FIXME: + * - Support for multiple devices + * - Split out MID specific GPIO handling eventually + */ + +static int ifx_spi_spi_probe(struct spi_device *spi) +{ + int ret; + int srdy; + struct ifx_modem_platform_data *pl_data = NULL; + struct ifx_spi_device *ifx_dev; + + if (saved_ifx_dev) { + dev_dbg(&spi->dev, "ignoring subsequent detection"); + return -ENODEV; + } + + /* initialize structure to hold our device variables */ + ifx_dev = kzalloc(sizeof(struct ifx_spi_device), GFP_KERNEL); + if (!ifx_dev) { + dev_err(&spi->dev, "spi device allocation failed"); + return -ENOMEM; + } + saved_ifx_dev = ifx_dev; + ifx_dev->spi_dev = spi; + clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags); + spin_lock_init(&ifx_dev->write_lock); + spin_lock_init(&ifx_dev->power_lock); + ifx_dev->power_status = 0; + init_timer(&ifx_dev->spi_timer); + ifx_dev->spi_timer.function = ifx_spi_timeout; + ifx_dev->spi_timer.data = (unsigned long)ifx_dev; + ifx_dev->is_6160 = pl_data->is_6160; + + /* ensure SPI protocol flags are initialized to enable transfer */ + ifx_dev->spi_more = 0; + ifx_dev->spi_slave_cts = 0; + + /*initialize transfer and dma buffers */ + ifx_dev->tx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev, + IFX_SPI_TRANSFER_SIZE, + &ifx_dev->tx_bus, + GFP_KERNEL); + if (!ifx_dev->tx_buffer) { + dev_err(&spi->dev, "DMA-TX buffer allocation failed"); + ret = -ENOMEM; + goto error_ret; + } + ifx_dev->rx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev, + IFX_SPI_TRANSFER_SIZE, + &ifx_dev->rx_bus, + GFP_KERNEL); + if (!ifx_dev->rx_buffer) { + dev_err(&spi->dev, "DMA-RX buffer allocation failed"); + ret = -ENOMEM; + goto error_ret; + } + + /* initialize waitq for modem reset */ + init_waitqueue_head(&ifx_dev->mdm_reset_wait); + + spi_set_drvdata(spi, ifx_dev); + tasklet_init(&ifx_dev->io_work_tasklet, ifx_spi_io, + (unsigned long)ifx_dev); + + set_bit(IFX_SPI_STATE_PRESENT, &ifx_dev->flags); + + /* create our tty port */ + ret = ifx_spi_create_port(ifx_dev); + if (ret != 0) { + dev_err(&spi->dev, "create default tty port failed"); + goto error_ret; + } + + pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data; + if (pl_data) { + ifx_dev->gpio.reset = pl_data->rst_pmu; + ifx_dev->gpio.po = pl_data->pwr_on; + ifx_dev->gpio.mrdy = pl_data->mrdy; + ifx_dev->gpio.srdy = pl_data->srdy; + ifx_dev->gpio.reset_out = pl_data->rst_out; + } else { + dev_err(&spi->dev, "missing platform data!"); + ret = -ENODEV; + goto error_ret; + } + + dev_info(&spi->dev, "gpios %d, %d, %d, %d, %d", + ifx_dev->gpio.reset, ifx_dev->gpio.po, ifx_dev->gpio.mrdy, + ifx_dev->gpio.srdy, ifx_dev->gpio.reset_out); + + /* Configure gpios */ + ret = gpio_request(ifx_dev->gpio.reset, "ifxModem"); + if (ret < 0) { + dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET)", + ifx_dev->gpio.reset); + goto error_ret; + } + ret += gpio_direction_output(ifx_dev->gpio.reset, 0); + ret += gpio_export(ifx_dev->gpio.reset, 1); + if (ret) { + dev_err(&spi->dev, "Unable to configure GPIO%d (RESET)", + ifx_dev->gpio.reset); + ret = -EBUSY; + goto error_ret2; + } + + ret = gpio_request(ifx_dev->gpio.po, "ifxModem"); + ret += gpio_direction_output(ifx_dev->gpio.po, 0); + ret += gpio_export(ifx_dev->gpio.po, 1); + if (ret) { + dev_err(&spi->dev, "Unable to configure GPIO%d (ON)", + ifx_dev->gpio.po); + ret = -EBUSY; + goto error_ret3; + } + + ret = gpio_request(ifx_dev->gpio.mrdy, "ifxModem"); + if (ret < 0) { + dev_err(&spi->dev, "Unable to allocate GPIO%d (MRDY)", + ifx_dev->gpio.mrdy); + goto error_ret3; + } + ret += gpio_export(ifx_dev->gpio.mrdy, 1); + ret += gpio_direction_output(ifx_dev->gpio.mrdy, 0); + if (ret) { + dev_err(&spi->dev, "Unable to configure GPIO%d (MRDY)", + ifx_dev->gpio.mrdy); + ret = -EBUSY; + goto error_ret4; + } + + ret = gpio_request(ifx_dev->gpio.srdy, "ifxModem"); + if (ret < 0) { + dev_err(&spi->dev, "Unable to allocate GPIO%d (SRDY)", + ifx_dev->gpio.srdy); + ret = -EBUSY; + goto error_ret4; + } + ret += gpio_export(ifx_dev->gpio.srdy, 1); + ret += gpio_direction_input(ifx_dev->gpio.srdy); + if (ret) { + dev_err(&spi->dev, "Unable to configure GPIO%d (SRDY)", + ifx_dev->gpio.srdy); + ret = -EBUSY; + goto error_ret5; + } + + ret = gpio_request(ifx_dev->gpio.reset_out, "ifxModem"); + if (ret < 0) { + dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET_OUT)", + ifx_dev->gpio.reset_out); + goto error_ret5; + } + ret += gpio_export(ifx_dev->gpio.reset_out, 1); + ret += gpio_direction_input(ifx_dev->gpio.reset_out); + if (ret) { + dev_err(&spi->dev, "Unable to configure GPIO%d (RESET_OUT)", + ifx_dev->gpio.reset_out); + ret = -EBUSY; + goto error_ret6; + } + + ret = request_irq(gpio_to_irq(ifx_dev->gpio.reset_out), + ifx_spi_reset_interrupt, + IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING, DRVNAME, + (void *)ifx_dev); + if (ret) { + dev_err(&spi->dev, "Unable to get irq %x\n", + gpio_to_irq(ifx_dev->gpio.reset_out)); + goto error_ret6; + } + + ret = ifx_spi_reset(ifx_dev); + + ret = request_irq(gpio_to_irq(ifx_dev->gpio.srdy), + ifx_spi_srdy_interrupt, + IRQF_TRIGGER_RISING, DRVNAME, + (void *)ifx_dev); + if (ret) { + dev_err(&spi->dev, "Unable to get irq %x", + gpio_to_irq(ifx_dev->gpio.srdy)); + goto error_ret7; + } + + /* set pm runtime power state and register with power system */ + pm_runtime_set_active(&spi->dev); + pm_runtime_enable(&spi->dev); + + /* handle case that modem is already signaling SRDY */ + /* no outgoing tty open at this point, this just satisfies the + * modem's read and should reset communication properly + */ + srdy = gpio_get_value(ifx_dev->gpio.srdy); + + if (srdy) { + mrdy_assert(ifx_dev); + ifx_spi_handle_srdy(ifx_dev); + } else + mrdy_set_low(ifx_dev); + return 0; + +error_ret7: + free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev); +error_ret6: + gpio_free(ifx_dev->gpio.srdy); +error_ret5: + gpio_free(ifx_dev->gpio.mrdy); +error_ret4: + gpio_free(ifx_dev->gpio.reset); +error_ret3: + gpio_free(ifx_dev->gpio.po); +error_ret2: + gpio_free(ifx_dev->gpio.reset_out); +error_ret: + ifx_spi_free_device(ifx_dev); + saved_ifx_dev = NULL; + return ret; +} + +/** + * ifx_spi_spi_remove - SPI device was removed + * @spi: SPI device + * + * FIXME: We should be shutting the device down here not in + * the module unload path. + */ + +static int ifx_spi_spi_remove(struct spi_device *spi) +{ + struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi); + /* stop activity */ + tasklet_kill(&ifx_dev->io_work_tasklet); + /* free irq */ + free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev); + free_irq(gpio_to_irq(ifx_dev->gpio.srdy), (void *)ifx_dev); + + gpio_free(ifx_dev->gpio.srdy); + gpio_free(ifx_dev->gpio.mrdy); + gpio_free(ifx_dev->gpio.reset); + gpio_free(ifx_dev->gpio.po); + gpio_free(ifx_dev->gpio.reset_out); + + /* free allocations */ + ifx_spi_free_device(ifx_dev); + + saved_ifx_dev = NULL; + return 0; +} + +/** + * ifx_spi_spi_shutdown - called on SPI shutdown + * @spi: SPI device + * + * No action needs to be taken here + */ + +static void ifx_spi_spi_shutdown(struct spi_device *spi) +{ +} + +/* + * various suspends and resumes have nothing to do + * no hardware to save state for + */ + +/** + * ifx_spi_spi_suspend - suspend SPI on system suspend + * @dev: device being suspended + * + * Suspend the SPI side. No action needed on Intel MID platforms, may + * need extending for other systems. + */ +static int ifx_spi_spi_suspend(struct spi_device *spi, pm_message_t msg) +{ + return 0; +} + +/** + * ifx_spi_spi_resume - resume SPI side on system resume + * @dev: device being suspended + * + * Suspend the SPI side. No action needed on Intel MID platforms, may + * need extending for other systems. + */ +static int ifx_spi_spi_resume(struct spi_device *spi) +{ + return 0; +} + +/** + * ifx_spi_pm_suspend - suspend modem on system suspend + * @dev: device being suspended + * + * Suspend the modem. No action needed on Intel MID platforms, may + * need extending for other systems. + */ +static int ifx_spi_pm_suspend(struct device *dev) +{ + return 0; +} + +/** + * ifx_spi_pm_resume - resume modem on system resume + * @dev: device being suspended + * + * Allow the modem to resume. No action needed. + * + * FIXME: do we need to reset anything here ? + */ +static int ifx_spi_pm_resume(struct device *dev) +{ + return 0; +} + +/** + * ifx_spi_pm_runtime_resume - suspend modem + * @dev: device being suspended + * + * Allow the modem to resume. No action needed. + */ +static int ifx_spi_pm_runtime_resume(struct device *dev) +{ + return 0; +} + +/** + * ifx_spi_pm_runtime_suspend - suspend modem + * @dev: device being suspended + * + * Allow the modem to suspend and thus suspend to continue up the + * device tree. + */ +static int ifx_spi_pm_runtime_suspend(struct device *dev) +{ + return 0; +} + +/** + * ifx_spi_pm_runtime_idle - check if modem idle + * @dev: our device + * + * Check conditions and queue runtime suspend if idle. + */ +static int ifx_spi_pm_runtime_idle(struct device *dev) +{ + struct spi_device *spi = to_spi_device(dev); + struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi); + + if (!ifx_dev->power_status) + pm_runtime_suspend(dev); + + return 0; +} + +static const struct dev_pm_ops ifx_spi_pm = { + .resume = ifx_spi_pm_resume, + .suspend = ifx_spi_pm_suspend, + .runtime_resume = ifx_spi_pm_runtime_resume, + .runtime_suspend = ifx_spi_pm_runtime_suspend, + .runtime_idle = ifx_spi_pm_runtime_idle +}; + +static const struct spi_device_id ifx_id_table[] = { + {"ifx6160", 0}, + {"ifx6260", 0}, + { } +}; +MODULE_DEVICE_TABLE(spi, ifx_id_table); + +/* spi operations */ +static const struct spi_driver ifx_spi_driver_6160 = { + .driver = { + .name = "ifx6160", + .bus = &spi_bus_type, + .pm = &ifx_spi_pm, + .owner = THIS_MODULE}, + .probe = ifx_spi_spi_probe, + .shutdown = ifx_spi_spi_shutdown, + .remove = __devexit_p(ifx_spi_spi_remove), + .suspend = ifx_spi_spi_suspend, + .resume = ifx_spi_spi_resume, + .id_table = ifx_id_table +}; + +/** + * ifx_spi_exit - module exit + * + * Unload the module. + */ + +static void __exit ifx_spi_exit(void) +{ + /* unregister */ + tty_unregister_driver(tty_drv); + spi_unregister_driver((void *)&ifx_spi_driver_6160); +} + +/** + * ifx_spi_init - module entry point + * + * Initialise the SPI and tty interfaces for the IFX SPI driver + * We need to initialize upper-edge spi driver after the tty + * driver because otherwise the spi probe will race + */ + +static int __init ifx_spi_init(void) +{ + int result; + + tty_drv = alloc_tty_driver(1); + if (!tty_drv) { + pr_err("%s: alloc_tty_driver failed", DRVNAME); + return -ENOMEM; + } + + tty_drv->magic = TTY_DRIVER_MAGIC; + tty_drv->owner = THIS_MODULE; + tty_drv->driver_name = DRVNAME; + tty_drv->name = TTYNAME; + tty_drv->minor_start = IFX_SPI_TTY_ID; + tty_drv->num = 1; + tty_drv->type = TTY_DRIVER_TYPE_SERIAL; + tty_drv->subtype = SERIAL_TYPE_NORMAL; + tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; + tty_drv->init_termios = tty_std_termios; + + tty_set_operations(tty_drv, &ifx_spi_serial_ops); + + result = tty_register_driver(tty_drv); + if (result) { + pr_err("%s: tty_register_driver failed(%d)", + DRVNAME, result); + put_tty_driver(tty_drv); + return result; + } + + result = spi_register_driver((void *)&ifx_spi_driver_6160); + if (result) { + pr_err("%s: spi_register_driver failed(%d)", + DRVNAME, result); + tty_unregister_driver(tty_drv); + } + return result; +} + +module_init(ifx_spi_init); +module_exit(ifx_spi_exit); + +MODULE_AUTHOR("Intel"); +MODULE_DESCRIPTION("IFX6x60 spi driver"); +MODULE_LICENSE("GPL"); +MODULE_INFO(Version, "0.1-IFX6x60"); diff --git a/drivers/serial/ifx6x60.h b/drivers/serial/ifx6x60.h new file mode 100644 index 000000000000..deb7b8d977dc --- /dev/null +++ b/drivers/serial/ifx6x60.h @@ -0,0 +1,129 @@ +/**************************************************************************** + * + * Driver for the IFX spi modem. + * + * Copyright (C) 2009, 2010 Intel Corp + * Jim Stanley <jim.stanley@intel.com> + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, + * USA + * + * + * + *****************************************************************************/ +#ifndef _IFX6X60_H +#define _IFX6X60_H + +#define DRVNAME "ifx6x60" +#define TTYNAME "ttyIFX" + +/* #define IFX_THROTTLE_CODE */ + +#define IFX_SPI_MAX_MINORS 1 +#define IFX_SPI_TRANSFER_SIZE 2048 +#define IFX_SPI_FIFO_SIZE 4096 + +#define IFX_SPI_HEADER_OVERHEAD 4 +#define IFX_RESET_TIMEOUT msecs_to_jiffies(50) + +/* device flags bitfield definitions */ +#define IFX_SPI_STATE_PRESENT 0 +#define IFX_SPI_STATE_IO_IN_PROGRESS 1 +#define IFX_SPI_STATE_IO_READY 2 +#define IFX_SPI_STATE_TIMER_PENDING 3 + +/* flow control bitfields */ +#define IFX_SPI_DCD 0 +#define IFX_SPI_CTS 1 +#define IFX_SPI_DSR 2 +#define IFX_SPI_RI 3 +#define IFX_SPI_DTR 4 +#define IFX_SPI_RTS 5 +#define IFX_SPI_TX_FC 6 +#define IFX_SPI_RX_FC 7 +#define IFX_SPI_UPDATE 8 + +#define IFX_SPI_PAYLOAD_SIZE (IFX_SPI_TRANSFER_SIZE - \ + IFX_SPI_HEADER_OVERHEAD) + +#define IFX_SPI_IRQ_TYPE DETECT_EDGE_RISING +#define IFX_SPI_GPIO_TARGET 0 +#define IFX_SPI_GPIO0 0x105 + +#define IFX_SPI_STATUS_TIMEOUT (2000*HZ) + +/* values for bits in power status byte */ +#define IFX_SPI_POWER_DATA_PENDING 1 +#define IFX_SPI_POWER_SRDY 2 + +struct ifx_spi_device { + /* Our SPI device */ + struct spi_device *spi_dev; + + /* Port specific data */ + struct kfifo tx_fifo; + spinlock_t fifo_lock; + unsigned long signal_state; + + /* TTY Layer logic */ + struct tty_port tty_port; + struct device *tty_dev; + int minor; + + /* Low level I/O work */ + struct tasklet_struct io_work_tasklet; + unsigned long flags; + dma_addr_t rx_dma; + dma_addr_t tx_dma; + + int is_6160; /* Modem type */ + + spinlock_t write_lock; + int write_pending; + spinlock_t power_lock; + unsigned char power_status; + + unsigned char *rx_buffer; + unsigned char *tx_buffer; + dma_addr_t rx_bus; + dma_addr_t tx_bus; + unsigned char spi_more; + unsigned char spi_slave_cts; + + struct timer_list spi_timer; + + struct spi_message spi_msg; + struct spi_transfer spi_xfer; + + struct { + /* gpio lines */ + unsigned short srdy; /* slave-ready gpio */ + unsigned short mrdy; /* master-ready gpio */ + unsigned short reset; /* modem-reset gpio */ + unsigned short po; /* modem-on gpio */ + unsigned short reset_out; /* modem-in-reset gpio */ + /* state/stats */ + int unack_srdy_int_nb; + } gpio; + + /* modem reset */ + unsigned long mdm_reset_state; +#define MR_START 0 +#define MR_INPROGRESS 1 +#define MR_COMPLETE 2 + wait_queue_head_t mdm_reset_wait; +}; + +#endif /* _IFX6X60_H */ diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index c4399e23565a..126ec7f568ec 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -838,7 +838,11 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new, static const char * mpc52xx_uart_type(struct uart_port *port) { - return port->type == PORT_MPC52xx ? "MPC52xx PSC" : NULL; + /* + * We keep using PORT_MPC52xx for historic reasons although it applies + * for MPC512x, too, but print "MPC5xxx" to not irritate users + */ + return port->type == PORT_MPC52xx ? "MPC5xxx PSC" : NULL; } static void diff --git a/drivers/serial/omap-serial.c b/drivers/serial/omap-serial.c index 1201eff1831e..7f2f01058789 100644 --- a/drivers/serial/omap-serial.c +++ b/drivers/serial/omap-serial.c @@ -866,12 +866,6 @@ serial_omap_type(struct uart_port *port) return up->name; } -#ifdef CONFIG_SERIAL_OMAP_CONSOLE - -static struct uart_omap_port *serial_omap_console_ports[4]; - -static struct uart_driver serial_omap_reg; - #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) static inline void wait_for_xmitr(struct uart_omap_port *up) @@ -905,6 +899,34 @@ static inline void wait_for_xmitr(struct uart_omap_port *up) } } +#ifdef CONFIG_CONSOLE_POLL + +static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch) +{ + struct uart_omap_port *up = (struct uart_omap_port *)port; + wait_for_xmitr(up); + serial_out(up, UART_TX, ch); +} + +static int serial_omap_poll_get_char(struct uart_port *port) +{ + struct uart_omap_port *up = (struct uart_omap_port *)port; + unsigned int status = serial_in(up, UART_LSR); + + if (!(status & UART_LSR_DR)) + return NO_POLL_CHAR; + + return serial_in(up, UART_RX); +} + +#endif /* CONFIG_CONSOLE_POLL */ + +#ifdef CONFIG_SERIAL_OMAP_CONSOLE + +static struct uart_omap_port *serial_omap_console_ports[4]; + +static struct uart_driver serial_omap_reg; + static void serial_omap_console_putchar(struct uart_port *port, int ch) { struct uart_omap_port *up = (struct uart_omap_port *)port; @@ -1022,6 +1044,10 @@ static struct uart_ops serial_omap_pops = { .request_port = serial_omap_request_port, .config_port = serial_omap_config_port, .verify_port = serial_omap_verify_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_put_char = serial_omap_poll_put_char, + .poll_get_char = serial_omap_poll_get_char, +#endif }; static struct uart_driver serial_omap_reg = { diff --git a/drivers/serial/pch_uart.c b/drivers/serial/pch_uart.c new file mode 100644 index 000000000000..70a61458ec42 --- /dev/null +++ b/drivers/serial/pch_uart.c @@ -0,0 +1,1451 @@ +/* + *Copyright (C) 2010 OKI SEMICONDUCTOR CO., LTD. + * + *This program is free software; you can redistribute it and/or modify + *it under the terms of the GNU General Public License as published by + *the Free Software Foundation; version 2 of the License. + * + *This program is distributed in the hope that it will be useful, + *but WITHOUT ANY WARRANTY; without even the implied warranty of + *MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + *GNU General Public License for more details. + * + *You should have received a copy of the GNU General Public License + *along with this program; if not, write to the Free Software + *Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. + */ +#include <linux/serial_reg.h> +#include <linux/pci.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/serial_core.h> +#include <linux/interrupt.h> +#include <linux/io.h> + +#include <linux/dmaengine.h> +#include <linux/pch_dma.h> + +enum { + PCH_UART_HANDLED_RX_INT_SHIFT, + PCH_UART_HANDLED_TX_INT_SHIFT, + PCH_UART_HANDLED_RX_ERR_INT_SHIFT, + PCH_UART_HANDLED_RX_TRG_INT_SHIFT, + PCH_UART_HANDLED_MS_INT_SHIFT, +}; + +enum { + PCH_UART_8LINE, + PCH_UART_2LINE, +}; + +#define PCH_UART_DRIVER_DEVICE "ttyPCH" + +#define PCH_UART_NR_GE_256FIFO 1 +#define PCH_UART_NR_GE_64FIFO 3 +#define PCH_UART_NR_GE (PCH_UART_NR_GE_256FIFO+PCH_UART_NR_GE_64FIFO) +#define PCH_UART_NR PCH_UART_NR_GE + +#define PCH_UART_HANDLED_RX_INT (1<<((PCH_UART_HANDLED_RX_INT_SHIFT)<<1)) +#define PCH_UART_HANDLED_TX_INT (1<<((PCH_UART_HANDLED_TX_INT_SHIFT)<<1)) +#define PCH_UART_HANDLED_RX_ERR_INT (1<<((\ + PCH_UART_HANDLED_RX_ERR_INT_SHIFT)<<1)) +#define PCH_UART_HANDLED_RX_TRG_INT (1<<((\ + PCH_UART_HANDLED_RX_TRG_INT_SHIFT)<<1)) +#define PCH_UART_HANDLED_MS_INT (1<<((PCH_UART_HANDLED_MS_INT_SHIFT)<<1)) + +#define PCH_UART_RBR 0x00 +#define PCH_UART_THR 0x00 + +#define PCH_UART_IER_MASK (PCH_UART_IER_ERBFI|PCH_UART_IER_ETBEI|\ + PCH_UART_IER_ELSI|PCH_UART_IER_EDSSI) +#define PCH_UART_IER_ERBFI 0x00000001 +#define PCH_UART_IER_ETBEI 0x00000002 +#define PCH_UART_IER_ELSI 0x00000004 +#define PCH_UART_IER_EDSSI 0x00000008 + +#define PCH_UART_IIR_IP 0x00000001 +#define PCH_UART_IIR_IID 0x00000006 +#define PCH_UART_IIR_MSI 0x00000000 +#define PCH_UART_IIR_TRI 0x00000002 +#define PCH_UART_IIR_RRI 0x00000004 +#define PCH_UART_IIR_REI 0x00000006 +#define PCH_UART_IIR_TOI 0x00000008 +#define PCH_UART_IIR_FIFO256 0x00000020 +#define PCH_UART_IIR_FIFO64 PCH_UART_IIR_FIFO256 +#define PCH_UART_IIR_FE 0x000000C0 + +#define PCH_UART_FCR_FIFOE 0x00000001 +#define PCH_UART_FCR_RFR 0x00000002 +#define PCH_UART_FCR_TFR 0x00000004 +#define PCH_UART_FCR_DMS 0x00000008 +#define PCH_UART_FCR_FIFO256 0x00000020 +#define PCH_UART_FCR_RFTL 0x000000C0 + +#define PCH_UART_FCR_RFTL1 0x00000000 +#define PCH_UART_FCR_RFTL64 0x00000040 +#define PCH_UART_FCR_RFTL128 0x00000080 +#define PCH_UART_FCR_RFTL224 0x000000C0 +#define PCH_UART_FCR_RFTL16 PCH_UART_FCR_RFTL64 +#define PCH_UART_FCR_RFTL32 PCH_UART_FCR_RFTL128 +#define PCH_UART_FCR_RFTL56 PCH_UART_FCR_RFTL224 +#define PCH_UART_FCR_RFTL4 PCH_UART_FCR_RFTL64 +#define PCH_UART_FCR_RFTL8 PCH_UART_FCR_RFTL128 +#define PCH_UART_FCR_RFTL14 PCH_UART_FCR_RFTL224 +#define PCH_UART_FCR_RFTL_SHIFT 6 + +#define PCH_UART_LCR_WLS 0x00000003 +#define PCH_UART_LCR_STB 0x00000004 +#define PCH_UART_LCR_PEN 0x00000008 +#define PCH_UART_LCR_EPS 0x00000010 +#define PCH_UART_LCR_SP 0x00000020 +#define PCH_UART_LCR_SB 0x00000040 +#define PCH_UART_LCR_DLAB 0x00000080 +#define PCH_UART_LCR_NP 0x00000000 +#define PCH_UART_LCR_OP PCH_UART_LCR_PEN +#define PCH_UART_LCR_EP (PCH_UART_LCR_PEN | PCH_UART_LCR_EPS) +#define PCH_UART_LCR_1P (PCH_UART_LCR_PEN | PCH_UART_LCR_SP) +#define PCH_UART_LCR_0P (PCH_UART_LCR_PEN | PCH_UART_LCR_EPS |\ + PCH_UART_LCR_SP) + +#define PCH_UART_LCR_5BIT 0x00000000 +#define PCH_UART_LCR_6BIT 0x00000001 +#define PCH_UART_LCR_7BIT 0x00000002 +#define PCH_UART_LCR_8BIT 0x00000003 + +#define PCH_UART_MCR_DTR 0x00000001 +#define PCH_UART_MCR_RTS 0x00000002 +#define PCH_UART_MCR_OUT 0x0000000C +#define PCH_UART_MCR_LOOP 0x00000010 +#define PCH_UART_MCR_AFE 0x00000020 + +#define PCH_UART_LSR_DR 0x00000001 +#define PCH_UART_LSR_ERR (1<<7) + +#define PCH_UART_MSR_DCTS 0x00000001 +#define PCH_UART_MSR_DDSR 0x00000002 +#define PCH_UART_MSR_TERI 0x00000004 +#define PCH_UART_MSR_DDCD 0x00000008 +#define PCH_UART_MSR_CTS 0x00000010 +#define PCH_UART_MSR_DSR 0x00000020 +#define PCH_UART_MSR_RI 0x00000040 +#define PCH_UART_MSR_DCD 0x00000080 +#define PCH_UART_MSR_DELTA (PCH_UART_MSR_DCTS | PCH_UART_MSR_DDSR |\ + PCH_UART_MSR_TERI | PCH_UART_MSR_DDCD) + +#define PCH_UART_DLL 0x00 +#define PCH_UART_DLM 0x01 + +#define DIV_ROUND(a, b) (((a) + ((b)/2)) / (b)) + +#define PCH_UART_IID_RLS (PCH_UART_IIR_REI) +#define PCH_UART_IID_RDR (PCH_UART_IIR_RRI) +#define PCH_UART_IID_RDR_TO (PCH_UART_IIR_RRI | PCH_UART_IIR_TOI) +#define PCH_UART_IID_THRE (PCH_UART_IIR_TRI) +#define PCH_UART_IID_MS (PCH_UART_IIR_MSI) + +#define PCH_UART_HAL_PARITY_NONE (PCH_UART_LCR_NP) +#define PCH_UART_HAL_PARITY_ODD (PCH_UART_LCR_OP) +#define PCH_UART_HAL_PARITY_EVEN (PCH_UART_LCR_EP) +#define PCH_UART_HAL_PARITY_FIX1 (PCH_UART_LCR_1P) +#define PCH_UART_HAL_PARITY_FIX0 (PCH_UART_LCR_0P) +#define PCH_UART_HAL_5BIT (PCH_UART_LCR_5BIT) +#define PCH_UART_HAL_6BIT (PCH_UART_LCR_6BIT) +#define PCH_UART_HAL_7BIT (PCH_UART_LCR_7BIT) +#define PCH_UART_HAL_8BIT (PCH_UART_LCR_8BIT) +#define PCH_UART_HAL_STB1 0 +#define PCH_UART_HAL_STB2 (PCH_UART_LCR_STB) + +#define PCH_UART_HAL_CLR_TX_FIFO (PCH_UART_FCR_TFR) +#define PCH_UART_HAL_CLR_RX_FIFO (PCH_UART_FCR_RFR) +#define PCH_UART_HAL_CLR_ALL_FIFO (PCH_UART_HAL_CLR_TX_FIFO | \ + PCH_UART_HAL_CLR_RX_FIFO) + +#define PCH_UART_HAL_DMA_MODE0 0 +#define PCH_UART_HAL_FIFO_DIS 0 +#define PCH_UART_HAL_FIFO16 (PCH_UART_FCR_FIFOE) +#define PCH_UART_HAL_FIFO256 (PCH_UART_FCR_FIFOE | \ + PCH_UART_FCR_FIFO256) +#define PCH_UART_HAL_FIFO64 (PCH_UART_HAL_FIFO256) +#define PCH_UART_HAL_TRIGGER1 (PCH_UART_FCR_RFTL1) +#define PCH_UART_HAL_TRIGGER64 (PCH_UART_FCR_RFTL64) +#define PCH_UART_HAL_TRIGGER128 (PCH_UART_FCR_RFTL128) +#define PCH_UART_HAL_TRIGGER224 (PCH_UART_FCR_RFTL224) +#define PCH_UART_HAL_TRIGGER16 (PCH_UART_FCR_RFTL16) +#define PCH_UART_HAL_TRIGGER32 (PCH_UART_FCR_RFTL32) +#define PCH_UART_HAL_TRIGGER56 (PCH_UART_FCR_RFTL56) +#define PCH_UART_HAL_TRIGGER4 (PCH_UART_FCR_RFTL4) +#define PCH_UART_HAL_TRIGGER8 (PCH_UART_FCR_RFTL8) +#define PCH_UART_HAL_TRIGGER14 (PCH_UART_FCR_RFTL14) +#define PCH_UART_HAL_TRIGGER_L (PCH_UART_FCR_RFTL64) +#define PCH_UART_HAL_TRIGGER_M (PCH_UART_FCR_RFTL128) +#define PCH_UART_HAL_TRIGGER_H (PCH_UART_FCR_RFTL224) + +#define PCH_UART_HAL_RX_INT (PCH_UART_IER_ERBFI) +#define PCH_UART_HAL_TX_INT (PCH_UART_IER_ETBEI) +#define PCH_UART_HAL_RX_ERR_INT (PCH_UART_IER_ELSI) +#define PCH_UART_HAL_MS_INT (PCH_UART_IER_EDSSI) +#define PCH_UART_HAL_ALL_INT (PCH_UART_IER_MASK) + +#define PCH_UART_HAL_DTR (PCH_UART_MCR_DTR) +#define PCH_UART_HAL_RTS (PCH_UART_MCR_RTS) +#define PCH_UART_HAL_OUT (PCH_UART_MCR_OUT) +#define PCH_UART_HAL_LOOP (PCH_UART_MCR_LOOP) +#define PCH_UART_HAL_AFE (PCH_UART_MCR_AFE) + +struct pch_uart_buffer { + unsigned char *buf; + int size; +}; + +struct eg20t_port { + struct uart_port port; + int port_type; + void __iomem *membase; + resource_size_t mapbase; + unsigned int iobase; + struct pci_dev *pdev; + int fifo_size; + int base_baud; + int start_tx; + int start_rx; + int tx_empty; + int int_dis_flag; + int trigger; + int trigger_level; + struct pch_uart_buffer rxbuf; + unsigned int dmsr; + unsigned int fcr; + unsigned int use_dma; + unsigned int use_dma_flag; + struct dma_async_tx_descriptor *desc_tx; + struct dma_async_tx_descriptor *desc_rx; + struct pch_dma_slave param_tx; + struct pch_dma_slave param_rx; + struct dma_chan *chan_tx; + struct dma_chan *chan_rx; + struct scatterlist sg_tx; + struct scatterlist sg_rx; + int tx_dma_use; + void *rx_buf_virt; + dma_addr_t rx_buf_dma; +}; + +static unsigned int default_baud = 9600; +static const int trigger_level_256[4] = { 1, 64, 128, 224 }; +static const int trigger_level_64[4] = { 1, 16, 32, 56 }; +static const int trigger_level_16[4] = { 1, 4, 8, 14 }; +static const int trigger_level_1[4] = { 1, 1, 1, 1 }; + +static void pch_uart_hal_request(struct pci_dev *pdev, int fifosize, + int base_baud) +{ + struct eg20t_port *priv = pci_get_drvdata(pdev); + + priv->trigger_level = 1; + priv->fcr = 0; +} + +static unsigned int get_msr(struct eg20t_port *priv, void __iomem *base) +{ + unsigned int msr = ioread8(base + UART_MSR); + priv->dmsr |= msr & PCH_UART_MSR_DELTA; + + return msr; +} + +static void pch_uart_hal_enable_interrupt(struct eg20t_port *priv, + unsigned int flag) +{ + u8 ier = ioread8(priv->membase + UART_IER); + ier |= flag & PCH_UART_IER_MASK; + iowrite8(ier, priv->membase + UART_IER); +} + +static void pch_uart_hal_disable_interrupt(struct eg20t_port *priv, + unsigned int flag) +{ + u8 ier = ioread8(priv->membase + UART_IER); + ier &= ~(flag & PCH_UART_IER_MASK); + iowrite8(ier, priv->membase + UART_IER); +} + +static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud, + unsigned int parity, unsigned int bits, + unsigned int stb) +{ + unsigned int dll, dlm, lcr; + int div; + + div = DIV_ROUND(priv->base_baud / 16, baud); + if (div < 0 || USHRT_MAX <= div) { + pr_err("Invalid Baud(div=0x%x)\n", div); + return -EINVAL; + } + + dll = (unsigned int)div & 0x00FFU; + dlm = ((unsigned int)div >> 8) & 0x00FFU; + + if (parity & ~(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS | PCH_UART_LCR_SP)) { + pr_err("Invalid parity(0x%x)\n", parity); + return -EINVAL; + } + + if (bits & ~PCH_UART_LCR_WLS) { + pr_err("Invalid bits(0x%x)\n", bits); + return -EINVAL; + } + + if (stb & ~PCH_UART_LCR_STB) { + pr_err("Invalid STB(0x%x)\n", stb); + return -EINVAL; + } + + lcr = parity; + lcr |= bits; + lcr |= stb; + + pr_debug("%s:baud = %d, div = %04x, lcr = %02x (%lu)\n", + __func__, baud, div, lcr, jiffies); + iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR); + iowrite8(dll, priv->membase + PCH_UART_DLL); + iowrite8(dlm, priv->membase + PCH_UART_DLM); + iowrite8(lcr, priv->membase + UART_LCR); + + return 0; +} + +static int pch_uart_hal_fifo_reset(struct eg20t_port *priv, + unsigned int flag) +{ + if (flag & ~(PCH_UART_FCR_TFR | PCH_UART_FCR_RFR)) { + pr_err("%s:Invalid flag(0x%x)\n", __func__, flag); + return -EINVAL; + } + + iowrite8(PCH_UART_FCR_FIFOE | priv->fcr, priv->membase + UART_FCR); + iowrite8(PCH_UART_FCR_FIFOE | priv->fcr | flag, + priv->membase + UART_FCR); + iowrite8(priv->fcr, priv->membase + UART_FCR); + + return 0; +} + +static int pch_uart_hal_set_fifo(struct eg20t_port *priv, + unsigned int dmamode, + unsigned int fifo_size, unsigned int trigger) +{ + u8 fcr; + + if (dmamode & ~PCH_UART_FCR_DMS) { + pr_err("%s:Invalid DMA Mode(0x%x)\n", __func__, dmamode); + return -EINVAL; + } + + if (fifo_size & ~(PCH_UART_FCR_FIFOE | PCH_UART_FCR_FIFO256)) { + pr_err("%s:Invalid FIFO SIZE(0x%x)\n", __func__, fifo_size); + return -EINVAL; + } + + if (trigger & ~PCH_UART_FCR_RFTL) { + pr_err("%s:Invalid TRIGGER(0x%x)\n", __func__, trigger); + return -EINVAL; + } + + switch (priv->fifo_size) { + case 256: + priv->trigger_level = + trigger_level_256[trigger >> PCH_UART_FCR_RFTL_SHIFT]; + break; + case 64: + priv->trigger_level = + trigger_level_64[trigger >> PCH_UART_FCR_RFTL_SHIFT]; + break; + case 16: + priv->trigger_level = + trigger_level_16[trigger >> PCH_UART_FCR_RFTL_SHIFT]; + break; + default: + priv->trigger_level = + trigger_level_1[trigger >> PCH_UART_FCR_RFTL_SHIFT]; + break; + } + fcr = + dmamode | fifo_size | trigger | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR; + iowrite8(PCH_UART_FCR_FIFOE, priv->membase + UART_FCR); + iowrite8(PCH_UART_FCR_FIFOE | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR, + priv->membase + UART_FCR); + iowrite8(fcr, priv->membase + UART_FCR); + priv->fcr = fcr; + + return 0; +} + +static u8 pch_uart_hal_get_modem(struct eg20t_port *priv) +{ + priv->dmsr = 0; + return get_msr(priv, priv->membase); +} + +static int pch_uart_hal_write(struct eg20t_port *priv, + const unsigned char *buf, int tx_size) +{ + int i; + unsigned int thr; + + for (i = 0; i < tx_size;) { + thr = buf[i++]; + iowrite8(thr, priv->membase + PCH_UART_THR); + } + return i; +} + +static int pch_uart_hal_read(struct eg20t_port *priv, unsigned char *buf, + int rx_size) +{ + int i; + u8 rbr, lsr; + + lsr = ioread8(priv->membase + UART_LSR); + for (i = 0, lsr = ioread8(priv->membase + UART_LSR); + i < rx_size && lsr & UART_LSR_DR; + lsr = ioread8(priv->membase + UART_LSR)) { + rbr = ioread8(priv->membase + PCH_UART_RBR); + buf[i++] = rbr; + } + return i; +} + +static unsigned int pch_uart_hal_get_iid(struct eg20t_port *priv) +{ + unsigned int iir; + int ret; + + iir = ioread8(priv->membase + UART_IIR); + ret = (iir & (PCH_UART_IIR_IID | PCH_UART_IIR_TOI | PCH_UART_IIR_IP)); + return ret; +} + +static u8 pch_uart_hal_get_line_status(struct eg20t_port *priv) +{ + return ioread8(priv->membase + UART_LSR); +} + +static void pch_uart_hal_set_break(struct eg20t_port *priv, int on) +{ + unsigned int lcr; + + lcr = ioread8(priv->membase + UART_LCR); + if (on) + lcr |= PCH_UART_LCR_SB; + else + lcr &= ~PCH_UART_LCR_SB; + + iowrite8(lcr, priv->membase + UART_LCR); +} + +static int push_rx(struct eg20t_port *priv, const unsigned char *buf, + int size) +{ + struct uart_port *port; + struct tty_struct *tty; + + port = &priv->port; + tty = tty_port_tty_get(&port->state->port); + if (!tty) { + pr_debug("%s:tty is busy now", __func__); + return -EBUSY; + } + + tty_insert_flip_string(tty, buf, size); + tty_flip_buffer_push(tty); + tty_kref_put(tty); + + return 0; +} + +static int pop_tx_x(struct eg20t_port *priv, unsigned char *buf) +{ + int ret; + struct uart_port *port = &priv->port; + + if (port->x_char) { + pr_debug("%s:X character send %02x (%lu)\n", __func__, + port->x_char, jiffies); + buf[0] = port->x_char; + port->x_char = 0; + ret = 1; + } else { + ret = 0; + } + + return ret; +} + +static int dma_push_rx(struct eg20t_port *priv, int size) +{ + struct tty_struct *tty; + int room; + struct uart_port *port = &priv->port; + + port = &priv->port; + tty = tty_port_tty_get(&port->state->port); + if (!tty) { + pr_debug("%s:tty is busy now", __func__); + return 0; + } + + room = tty_buffer_request_room(tty, size); + + if (room < size) + dev_warn(port->dev, "Rx overrun: dropping %u bytes\n", + size - room); + if (!room) + return room; + + tty_insert_flip_string(tty, sg_virt(&priv->sg_rx), size); + + port->icount.rx += room; + tty_kref_put(tty); + + return room; +} + +static void pch_free_dma(struct uart_port *port) +{ + struct eg20t_port *priv; + priv = container_of(port, struct eg20t_port, port); + + if (priv->chan_tx) { + dma_release_channel(priv->chan_tx); + priv->chan_tx = NULL; + } + if (priv->chan_rx) { + dma_release_channel(priv->chan_rx); + priv->chan_rx = NULL; + } + if (sg_dma_address(&priv->sg_rx)) + dma_free_coherent(port->dev, port->fifosize, + sg_virt(&priv->sg_rx), + sg_dma_address(&priv->sg_rx)); + + return; +} + +static bool filter(struct dma_chan *chan, void *slave) +{ + struct pch_dma_slave *param = slave; + + if ((chan->chan_id == param->chan_id) && (param->dma_dev == + chan->device->dev)) { + chan->private = param; + return true; + } else { + return false; + } +} + +static void pch_request_dma(struct uart_port *port) +{ + dma_cap_mask_t mask; + struct dma_chan *chan; + struct pci_dev *dma_dev; + struct pch_dma_slave *param; + struct eg20t_port *priv = + container_of(port, struct eg20t_port, port); + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + + dma_dev = pci_get_bus_and_slot(2, PCI_DEVFN(0xa, 0)); /* Get DMA's dev + information */ + /* Set Tx DMA */ + param = &priv->param_tx; + param->dma_dev = &dma_dev->dev; + param->chan_id = priv->port.line; + param->tx_reg = port->mapbase + UART_TX; + chan = dma_request_channel(mask, filter, param); + if (!chan) { + pr_err("%s:dma_request_channel FAILS(Tx)\n", __func__); + return; + } + priv->chan_tx = chan; + + /* Set Rx DMA */ + param = &priv->param_rx; + param->dma_dev = &dma_dev->dev; + param->chan_id = priv->port.line + 1; /* Rx = Tx + 1 */ + param->rx_reg = port->mapbase + UART_RX; + chan = dma_request_channel(mask, filter, param); + if (!chan) { + pr_err("%s:dma_request_channel FAILS(Rx)\n", __func__); + dma_release_channel(priv->chan_tx); + return; + } + + /* Get Consistent memory for DMA */ + priv->rx_buf_virt = dma_alloc_coherent(port->dev, port->fifosize, + &priv->rx_buf_dma, GFP_KERNEL); + priv->chan_rx = chan; +} + +static void pch_dma_rx_complete(void *arg) +{ + struct eg20t_port *priv = arg; + struct uart_port *port = &priv->port; + struct tty_struct *tty = tty_port_tty_get(&port->state->port); + + if (!tty) { + pr_debug("%s:tty is busy now", __func__); + return; + } + + if (dma_push_rx(priv, priv->trigger_level)) + tty_flip_buffer_push(tty); + + tty_kref_put(tty); +} + +static void pch_dma_tx_complete(void *arg) +{ + struct eg20t_port *priv = arg; + struct uart_port *port = &priv->port; + struct circ_buf *xmit = &port->state->xmit; + + xmit->tail += sg_dma_len(&priv->sg_tx); + xmit->tail &= UART_XMIT_SIZE - 1; + port->icount.tx += sg_dma_len(&priv->sg_tx); + + async_tx_ack(priv->desc_tx); + priv->tx_dma_use = 0; +} + +static int pop_tx(struct eg20t_port *priv, unsigned char *buf, int size) +{ + int count = 0; + struct uart_port *port = &priv->port; + struct circ_buf *xmit = &port->state->xmit; + + if (uart_tx_stopped(port) || uart_circ_empty(xmit) || count >= size) + goto pop_tx_end; + + do { + int cnt_to_end = + CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); + int sz = min(size - count, cnt_to_end); + memcpy(&buf[count], &xmit->buf[xmit->tail], sz); + xmit->tail = (xmit->tail + sz) & (UART_XMIT_SIZE - 1); + count += sz; + } while (!uart_circ_empty(xmit) && count < size); + +pop_tx_end: + pr_debug("%d characters. Remained %d characters. (%lu)\n", + count, size - count, jiffies); + + return count; +} + +static int handle_rx_to(struct eg20t_port *priv) +{ + struct pch_uart_buffer *buf; + int rx_size; + int ret; + if (!priv->start_rx) { + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT); + return 0; + } + buf = &priv->rxbuf; + do { + rx_size = pch_uart_hal_read(priv, buf->buf, buf->size); + ret = push_rx(priv, buf->buf, rx_size); + if (ret) + return 0; + } while (rx_size == buf->size); + + return PCH_UART_HANDLED_RX_INT; +} + +static int handle_rx(struct eg20t_port *priv) +{ + return handle_rx_to(priv); +} + +static int dma_handle_rx(struct eg20t_port *priv) +{ + struct uart_port *port = &priv->port; + struct dma_async_tx_descriptor *desc; + struct scatterlist *sg; + + priv = container_of(port, struct eg20t_port, port); + sg = &priv->sg_rx; + + sg_init_table(&priv->sg_rx, 1); /* Initialize SG table */ + + sg_dma_len(sg) = priv->fifo_size; + + sg_set_page(&priv->sg_rx, virt_to_page(priv->rx_buf_virt), + sg_dma_len(sg), (unsigned long)priv->rx_buf_virt & + ~PAGE_MASK); + + sg_dma_address(sg) = priv->rx_buf_dma; + + desc = priv->chan_rx->device->device_prep_slave_sg(priv->chan_rx, + sg, 1, DMA_FROM_DEVICE, + DMA_PREP_INTERRUPT); + if (!desc) + return 0; + + priv->desc_rx = desc; + desc->callback = pch_dma_rx_complete; + desc->callback_param = priv; + desc->tx_submit(desc); + dma_async_issue_pending(priv->chan_rx); + + return PCH_UART_HANDLED_RX_INT; +} + +static unsigned int handle_tx(struct eg20t_port *priv) +{ + struct uart_port *port = &priv->port; + struct circ_buf *xmit = &port->state->xmit; + int ret; + int fifo_size; + int tx_size; + int size; + int tx_empty; + + if (!priv->start_tx) { + pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies); + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); + priv->tx_empty = 1; + return 0; + } + + fifo_size = max(priv->fifo_size, 1); + tx_empty = 1; + if (pop_tx_x(priv, xmit->buf)) { + pch_uart_hal_write(priv, xmit->buf, 1); + port->icount.tx++; + tx_empty = 0; + fifo_size--; + } + size = min(xmit->head - xmit->tail, fifo_size); + tx_size = pop_tx(priv, xmit->buf, size); + if (tx_size > 0) { + ret = pch_uart_hal_write(priv, xmit->buf, tx_size); + port->icount.tx += ret; + tx_empty = 0; + } + + priv->tx_empty = tx_empty; + + if (tx_empty) + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); + + return PCH_UART_HANDLED_TX_INT; +} + +static unsigned int dma_handle_tx(struct eg20t_port *priv) +{ + struct uart_port *port = &priv->port; + struct circ_buf *xmit = &port->state->xmit; + struct scatterlist *sg = &priv->sg_tx; + int nent; + int fifo_size; + int tx_empty; + struct dma_async_tx_descriptor *desc; + + if (!priv->start_tx) { + pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies); + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); + priv->tx_empty = 1; + return 0; + } + + fifo_size = max(priv->fifo_size, 1); + tx_empty = 1; + if (pop_tx_x(priv, xmit->buf)) { + pch_uart_hal_write(priv, xmit->buf, 1); + port->icount.tx++; + tx_empty = 0; + fifo_size--; + } + + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); + + priv->tx_dma_use = 1; + + sg_init_table(&priv->sg_tx, 1); /* Initialize SG table */ + + sg_set_page(&priv->sg_tx, virt_to_page(xmit->buf), + UART_XMIT_SIZE, (int)xmit->buf & ~PAGE_MASK); + + nent = dma_map_sg(port->dev, &priv->sg_tx, 1, DMA_TO_DEVICE); + if (!nent) { + pr_err("%s:dma_map_sg Failed\n", __func__); + return 0; + } + + sg->offset = xmit->tail & (UART_XMIT_SIZE - 1); + sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) + + sg->offset; + sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail, + UART_XMIT_SIZE), CIRC_CNT_TO_END(xmit->head, + xmit->tail, UART_XMIT_SIZE)); + + desc = priv->chan_tx->device->device_prep_slave_sg(priv->chan_tx, + sg, nent, DMA_TO_DEVICE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) { + pr_err("%s:device_prep_slave_sg Failed\n", __func__); + return 0; + } + + dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE); + + priv->desc_tx = desc; + desc->callback = pch_dma_tx_complete; + desc->callback_param = priv; + + desc->tx_submit(desc); + + dma_async_issue_pending(priv->chan_tx); + + return PCH_UART_HANDLED_TX_INT; +} + +static void pch_uart_err_ir(struct eg20t_port *priv, unsigned int lsr) +{ + u8 fcr = ioread8(priv->membase + UART_FCR); + + /* Reset FIFO */ + fcr |= UART_FCR_CLEAR_RCVR; + iowrite8(fcr, priv->membase + UART_FCR); + + if (lsr & PCH_UART_LSR_ERR) + dev_err(&priv->pdev->dev, "Error data in FIFO\n"); + + if (lsr & UART_LSR_FE) + dev_err(&priv->pdev->dev, "Framing Error\n"); + + if (lsr & UART_LSR_PE) + dev_err(&priv->pdev->dev, "Parity Error\n"); + + if (lsr & UART_LSR_OE) + dev_err(&priv->pdev->dev, "Overrun Error\n"); +} + +static irqreturn_t pch_uart_interrupt(int irq, void *dev_id) +{ + struct eg20t_port *priv = dev_id; + unsigned int handled; + u8 lsr; + int ret = 0; + unsigned int iid; + unsigned long flags; + + spin_lock_irqsave(&priv->port.lock, flags); + handled = 0; + while ((iid = pch_uart_hal_get_iid(priv)) > 1) { + switch (iid) { + case PCH_UART_IID_RLS: /* Receiver Line Status */ + lsr = pch_uart_hal_get_line_status(priv); + if (lsr & (PCH_UART_LSR_ERR | UART_LSR_FE | + UART_LSR_PE | UART_LSR_OE)) { + pch_uart_err_ir(priv, lsr); + ret = PCH_UART_HANDLED_RX_ERR_INT; + } + break; + case PCH_UART_IID_RDR: /* Received Data Ready */ + if (priv->use_dma) + ret = dma_handle_rx(priv); + else + ret = handle_rx(priv); + break; + case PCH_UART_IID_RDR_TO: /* Received Data Ready + (FIFO Timeout) */ + ret = handle_rx_to(priv); + break; + case PCH_UART_IID_THRE: /* Transmitter Holding Register + Empty */ + if (priv->use_dma) + ret = dma_handle_tx(priv); + else + ret = handle_tx(priv); + break; + case PCH_UART_IID_MS: /* Modem Status */ + ret = PCH_UART_HANDLED_MS_INT; + break; + default: /* Never junp to this label */ + pr_err("%s:iid=%d (%lu)\n", __func__, iid, jiffies); + ret = -1; + break; + } + handled |= (unsigned int)ret; + } + if (handled == 0 && iid <= 1) { + if (priv->int_dis_flag) + priv->int_dis_flag = 0; + } + + spin_unlock_irqrestore(&priv->port.lock, flags); + return IRQ_RETVAL(handled); +} + +/* This function tests whether the transmitter fifo and shifter for the port + described by 'port' is empty. */ +static unsigned int pch_uart_tx_empty(struct uart_port *port) +{ + struct eg20t_port *priv; + int ret; + priv = container_of(port, struct eg20t_port, port); + if (priv->tx_empty) + ret = TIOCSER_TEMT; + else + ret = 0; + + return ret; +} + +/* Returns the current state of modem control inputs. */ +static unsigned int pch_uart_get_mctrl(struct uart_port *port) +{ + struct eg20t_port *priv; + u8 modem; + unsigned int ret = 0; + + priv = container_of(port, struct eg20t_port, port); + modem = pch_uart_hal_get_modem(priv); + + if (modem & UART_MSR_DCD) + ret |= TIOCM_CAR; + + if (modem & UART_MSR_RI) + ret |= TIOCM_RNG; + + if (modem & UART_MSR_DSR) + ret |= TIOCM_DSR; + + if (modem & UART_MSR_CTS) + ret |= TIOCM_CTS; + + return ret; +} + +static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + u32 mcr = 0; + unsigned int dat; + struct eg20t_port *priv = container_of(port, struct eg20t_port, port); + + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + if (mctrl) { + dat = pch_uart_get_mctrl(port); + dat |= mcr; + iowrite8(dat, priv->membase + UART_MCR); + } +} + +static void pch_uart_stop_tx(struct uart_port *port) +{ + struct eg20t_port *priv; + priv = container_of(port, struct eg20t_port, port); + priv->start_tx = 0; + priv->tx_dma_use = 0; +} + +static void pch_uart_start_tx(struct uart_port *port) +{ + struct eg20t_port *priv; + + priv = container_of(port, struct eg20t_port, port); + + if (priv->use_dma) + if (priv->tx_dma_use) + return; + + priv->start_tx = 1; + pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT); +} + +static void pch_uart_stop_rx(struct uart_port *port) +{ + struct eg20t_port *priv; + priv = container_of(port, struct eg20t_port, port); + priv->start_rx = 0; + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT); + priv->int_dis_flag = 1; +} + +/* Enable the modem status interrupts. */ +static void pch_uart_enable_ms(struct uart_port *port) +{ + struct eg20t_port *priv; + priv = container_of(port, struct eg20t_port, port); + pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_MS_INT); +} + +/* Control the transmission of a break signal. */ +static void pch_uart_break_ctl(struct uart_port *port, int ctl) +{ + struct eg20t_port *priv; + unsigned long flags; + + priv = container_of(port, struct eg20t_port, port); + spin_lock_irqsave(&port->lock, flags); + pch_uart_hal_set_break(priv, ctl); + spin_unlock_irqrestore(&port->lock, flags); +} + +/* Grab any interrupt resources and initialise any low level driver state. */ +static int pch_uart_startup(struct uart_port *port) +{ + struct eg20t_port *priv; + int ret; + int fifo_size; + int trigger_level; + + priv = container_of(port, struct eg20t_port, port); + priv->tx_empty = 1; + port->uartclk = priv->base_baud; + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); + ret = pch_uart_hal_set_line(priv, default_baud, + PCH_UART_HAL_PARITY_NONE, PCH_UART_HAL_8BIT, + PCH_UART_HAL_STB1); + if (ret) + return ret; + + switch (priv->fifo_size) { + case 256: + fifo_size = PCH_UART_HAL_FIFO256; + break; + case 64: + fifo_size = PCH_UART_HAL_FIFO64; + break; + case 16: + fifo_size = PCH_UART_HAL_FIFO16; + case 1: + default: + fifo_size = PCH_UART_HAL_FIFO_DIS; + break; + } + + switch (priv->trigger) { + case PCH_UART_HAL_TRIGGER1: + trigger_level = 1; + break; + case PCH_UART_HAL_TRIGGER_L: + trigger_level = priv->fifo_size / 4; + break; + case PCH_UART_HAL_TRIGGER_M: + trigger_level = priv->fifo_size / 2; + break; + case PCH_UART_HAL_TRIGGER_H: + default: + trigger_level = priv->fifo_size - (priv->fifo_size / 8); + break; + } + + priv->trigger_level = trigger_level; + ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0, + fifo_size, priv->trigger); + if (ret < 0) + return ret; + + ret = request_irq(priv->port.irq, pch_uart_interrupt, IRQF_SHARED, + KBUILD_MODNAME, priv); + if (ret < 0) + return ret; + + if (priv->use_dma) + pch_request_dma(port); + + priv->start_rx = 1; + pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT); + uart_update_timeout(port, CS8, default_baud); + + return 0; +} + +static void pch_uart_shutdown(struct uart_port *port) +{ + struct eg20t_port *priv; + int ret; + + priv = container_of(port, struct eg20t_port, port); + pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); + pch_uart_hal_fifo_reset(priv, PCH_UART_HAL_CLR_ALL_FIFO); + ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0, + PCH_UART_HAL_FIFO_DIS, PCH_UART_HAL_TRIGGER1); + if (ret) + pr_err("pch_uart_hal_set_fifo Failed(ret=%d)\n", ret); + + if (priv->use_dma_flag) + pch_free_dma(port); + + free_irq(priv->port.irq, priv); +} + +/* Change the port parameters, including word length, parity, stop + *bits. Update read_status_mask and ignore_status_mask to indicate + *the types of events we are interested in receiving. */ +static void pch_uart_set_termios(struct uart_port *port, + struct ktermios *termios, struct ktermios *old) +{ + int baud; + int rtn; + unsigned int parity, bits, stb; + struct eg20t_port *priv; + unsigned long flags; + + priv = container_of(port, struct eg20t_port, port); + switch (termios->c_cflag & CSIZE) { + case CS5: + bits = PCH_UART_HAL_5BIT; + break; + case CS6: + bits = PCH_UART_HAL_6BIT; + break; + case CS7: + bits = PCH_UART_HAL_7BIT; + break; + default: /* CS8 */ + bits = PCH_UART_HAL_8BIT; + break; + } + if (termios->c_cflag & CSTOPB) + stb = PCH_UART_HAL_STB2; + else + stb = PCH_UART_HAL_STB1; + + if (termios->c_cflag & PARENB) { + if (!(termios->c_cflag & PARODD)) + parity = PCH_UART_HAL_PARITY_ODD; + else + parity = PCH_UART_HAL_PARITY_EVEN; + + } else { + parity = PCH_UART_HAL_PARITY_NONE; + } + termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */ + + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + + spin_lock_irqsave(&port->lock, flags); + + uart_update_timeout(port, termios->c_cflag, baud); + rtn = pch_uart_hal_set_line(priv, baud, parity, bits, stb); + if (rtn) + goto out; + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); + +out: + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *pch_uart_type(struct uart_port *port) +{ + return KBUILD_MODNAME; +} + +static void pch_uart_release_port(struct uart_port *port) +{ + struct eg20t_port *priv; + + priv = container_of(port, struct eg20t_port, port); + pci_iounmap(priv->pdev, priv->membase); + pci_release_regions(priv->pdev); +} + +static int pch_uart_request_port(struct uart_port *port) +{ + struct eg20t_port *priv; + int ret; + void __iomem *membase; + + priv = container_of(port, struct eg20t_port, port); + ret = pci_request_regions(priv->pdev, KBUILD_MODNAME); + if (ret < 0) + return -EBUSY; + + membase = pci_iomap(priv->pdev, 1, 0); + if (!membase) { + pci_release_regions(priv->pdev); + return -EBUSY; + } + priv->membase = port->membase = membase; + + return 0; +} + +static void pch_uart_config_port(struct uart_port *port, int type) +{ + struct eg20t_port *priv; + + priv = container_of(port, struct eg20t_port, port); + if (type & UART_CONFIG_TYPE) { + port->type = priv->port_type; + pch_uart_request_port(port); + } +} + +static int pch_uart_verify_port(struct uart_port *port, + struct serial_struct *serinfo) +{ + struct eg20t_port *priv; + + priv = container_of(port, struct eg20t_port, port); + if (serinfo->flags & UPF_LOW_LATENCY) { + pr_info("PCH UART : Use PIO Mode (without DMA)\n"); + priv->use_dma = 0; + serinfo->flags &= ~UPF_LOW_LATENCY; + } else { +#ifndef CONFIG_PCH_DMA + pr_err("%s : PCH DMA is not Loaded.\n", __func__); + return -EOPNOTSUPP; +#endif + priv->use_dma = 1; + priv->use_dma_flag = 1; + pr_info("PCH UART : Use DMA Mode\n"); + } + + return 0; +} + +static struct uart_ops pch_uart_ops = { + .tx_empty = pch_uart_tx_empty, + .set_mctrl = pch_uart_set_mctrl, + .get_mctrl = pch_uart_get_mctrl, + .stop_tx = pch_uart_stop_tx, + .start_tx = pch_uart_start_tx, + .stop_rx = pch_uart_stop_rx, + .enable_ms = pch_uart_enable_ms, + .break_ctl = pch_uart_break_ctl, + .startup = pch_uart_startup, + .shutdown = pch_uart_shutdown, + .set_termios = pch_uart_set_termios, +/* .pm = pch_uart_pm, Not supported yet */ +/* .set_wake = pch_uart_set_wake, Not supported yet */ + .type = pch_uart_type, + .release_port = pch_uart_release_port, + .request_port = pch_uart_request_port, + .config_port = pch_uart_config_port, + .verify_port = pch_uart_verify_port +}; + +static struct uart_driver pch_uart_driver = { + .owner = THIS_MODULE, + .driver_name = KBUILD_MODNAME, + .dev_name = PCH_UART_DRIVER_DEVICE, + .major = 0, + .minor = 0, + .nr = PCH_UART_NR, +}; + +static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev, + int port_type) +{ + struct eg20t_port *priv; + int ret; + unsigned int iobase; + unsigned int mapbase; + unsigned char *rxbuf; + int fifosize, base_baud; + static int num; + + priv = kzalloc(sizeof(struct eg20t_port), GFP_KERNEL); + if (priv == NULL) + goto init_port_alloc_err; + + rxbuf = (unsigned char *)__get_free_page(GFP_KERNEL); + if (!rxbuf) + goto init_port_free_txbuf; + + switch (port_type) { + case PORT_UNKNOWN: + fifosize = 256; /* UART0 */ + base_baud = 1843200; /* 1.8432MHz */ + break; + case PORT_8250: + fifosize = 64; /* UART1~3 */ + base_baud = 1843200; /* 1.8432MHz */ + break; + default: + dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type); + goto init_port_hal_free; + } + + iobase = pci_resource_start(pdev, 0); + mapbase = pci_resource_start(pdev, 1); + priv->mapbase = mapbase; + priv->iobase = iobase; + priv->pdev = pdev; + priv->tx_empty = 1; + priv->rxbuf.buf = rxbuf; + priv->rxbuf.size = PAGE_SIZE; + + priv->fifo_size = fifosize; + priv->base_baud = base_baud; + priv->port_type = PORT_MAX_8250 + port_type + 1; + priv->port.dev = &pdev->dev; + priv->port.iobase = iobase; + priv->port.membase = NULL; + priv->port.mapbase = mapbase; + priv->port.irq = pdev->irq; + priv->port.iotype = UPIO_PORT; + priv->port.ops = &pch_uart_ops; + priv->port.flags = UPF_BOOT_AUTOCONF; + priv->port.fifosize = fifosize; + priv->port.line = num++; + priv->trigger = PCH_UART_HAL_TRIGGER_M; + + pci_set_drvdata(pdev, priv); + pch_uart_hal_request(pdev, fifosize, base_baud); + ret = uart_add_one_port(&pch_uart_driver, &priv->port); + if (ret < 0) + goto init_port_hal_free; + + return priv; + +init_port_hal_free: + free_page((unsigned long)rxbuf); +init_port_free_txbuf: + kfree(priv); +init_port_alloc_err: + + return NULL; +} + +static void pch_uart_exit_port(struct eg20t_port *priv) +{ + uart_remove_one_port(&pch_uart_driver, &priv->port); + pci_set_drvdata(priv->pdev, NULL); + free_page((unsigned long)priv->rxbuf.buf); +} + +static void pch_uart_pci_remove(struct pci_dev *pdev) +{ + struct eg20t_port *priv; + + priv = (struct eg20t_port *)pci_get_drvdata(pdev); + pch_uart_exit_port(priv); + pci_disable_device(pdev); + kfree(priv); + return; +} +#ifdef CONFIG_PM +static int pch_uart_pci_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct eg20t_port *priv = pci_get_drvdata(pdev); + + uart_suspend_port(&pch_uart_driver, &priv->port); + + pci_save_state(pdev); + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + return 0; +} + +static int pch_uart_pci_resume(struct pci_dev *pdev) +{ + struct eg20t_port *priv = pci_get_drvdata(pdev); + int ret; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + + ret = pci_enable_device(pdev); + if (ret) { + dev_err(&pdev->dev, + "%s-pci_enable_device failed(ret=%d) ", __func__, ret); + return ret; + } + + uart_resume_port(&pch_uart_driver, &priv->port); + + return 0; +} +#else +#define pch_uart_pci_suspend NULL +#define pch_uart_pci_resume NULL +#endif + +static DEFINE_PCI_DEVICE_TABLE(pch_uart_pci_id) = { + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8811), + .driver_data = PCH_UART_8LINE}, + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8812), + .driver_data = PCH_UART_2LINE}, + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8813), + .driver_data = PCH_UART_2LINE}, + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8814), + .driver_data = PCH_UART_2LINE}, + {0,}, +}; + +static int __devinit pch_uart_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *id) +{ + int ret; + struct eg20t_port *priv; + + ret = pci_enable_device(pdev); + if (ret < 0) + goto probe_error; + + priv = pch_uart_init_port(pdev, id->driver_data); + if (!priv) { + ret = -EBUSY; + goto probe_disable_device; + } + pci_set_drvdata(pdev, priv); + + return ret; + +probe_disable_device: + pci_disable_device(pdev); +probe_error: + return ret; +} + +static struct pci_driver pch_uart_pci_driver = { + .name = "pch_uart", + .id_table = pch_uart_pci_id, + .probe = pch_uart_pci_probe, + .remove = __devexit_p(pch_uart_pci_remove), + .suspend = pch_uart_pci_suspend, + .resume = pch_uart_pci_resume, +}; + +static int __init pch_uart_module_init(void) +{ + int ret; + + /* register as UART driver */ + ret = uart_register_driver(&pch_uart_driver); + if (ret < 0) + return ret; + + /* register as PCI driver */ + ret = pci_register_driver(&pch_uart_pci_driver); + if (ret < 0) + uart_unregister_driver(&pch_uart_driver); + + return ret; +} +module_init(pch_uart_module_init); + +static void __exit pch_uart_module_exit(void) +{ + pci_unregister_driver(&pch_uart_pci_driver); + uart_unregister_driver(&pch_uart_driver); +} +module_exit(pch_uart_module_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("Intel EG20T PCH UART PCI Driver"); +module_param(default_baud, uint, S_IRUGO); diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 9ffa5bee44ab..460a72d91bb7 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -1985,7 +1985,8 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) tty_dev = device_find_child(uport->dev, &match, serial_match_port); if (device_may_wakeup(tty_dev)) { - enable_irq_wake(uport->irq); + if (!enable_irq_wake(uport->irq)) + uport->irq_wake = 1; put_device(tty_dev); mutex_unlock(&port->mutex); return 0; @@ -2051,7 +2052,10 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) tty_dev = device_find_child(uport->dev, &match, serial_match_port); if (!uport->suspended && device_may_wakeup(tty_dev)) { - disable_irq_wake(uport->irq); + if (uport->irq_wake) { + disable_irq_wake(uport->irq); + uport->irq_wake = 0; + } mutex_unlock(&port->mutex); return 0; } @@ -2134,6 +2138,7 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port) case UPIO_AU: case UPIO_TSI: case UPIO_DWAPB: + case UPIO_DWAPB32: snprintf(address, sizeof(address), "MMIO 0x%llx", (unsigned long long)port->mapbase); break; @@ -2554,6 +2559,7 @@ int uart_match_port(struct uart_port *port1, struct uart_port *port2) case UPIO_AU: case UPIO_TSI: case UPIO_DWAPB: + case UPIO_DWAPB32: return (port1->mapbase == port2->mapbase); } return 0; diff --git a/drivers/serial/vt8500_serial.c b/drivers/serial/vt8500_serial.c new file mode 100644 index 000000000000..322bf56c0d89 --- /dev/null +++ b/drivers/serial/vt8500_serial.c @@ -0,0 +1,648 @@ +/* + * drivers/serial/vt8500_serial.c + * + * Copyright (C) 2010 Alexey Charkov <alchark@gmail.com> + * + * Based on msm_serial.c, which is: + * Copyright (C) 2007 Google, Inc. + * Author: Robert Love <rlove@google.com> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#if defined(CONFIG_SERIAL_VT8500_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +# define SUPPORT_SYSRQ +#endif + +#include <linux/hrtimer.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/irq.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/slab.h> +#include <linux/clk.h> +#include <linux/platform_device.h> + +/* + * UART Register offsets + */ + +#define VT8500_URTDR 0x0000 /* Transmit data */ +#define VT8500_URRDR 0x0004 /* Receive data */ +#define VT8500_URDIV 0x0008 /* Clock/Baud rate divisor */ +#define VT8500_URLCR 0x000C /* Line control */ +#define VT8500_URICR 0x0010 /* IrDA control */ +#define VT8500_URIER 0x0014 /* Interrupt enable */ +#define VT8500_URISR 0x0018 /* Interrupt status */ +#define VT8500_URUSR 0x001c /* UART status */ +#define VT8500_URFCR 0x0020 /* FIFO control */ +#define VT8500_URFIDX 0x0024 /* FIFO index */ +#define VT8500_URBKR 0x0028 /* Break signal count */ +#define VT8500_URTOD 0x002c /* Time out divisor */ +#define VT8500_TXFIFO 0x1000 /* Transmit FIFO (16x8) */ +#define VT8500_RXFIFO 0x1020 /* Receive FIFO (16x10) */ + +/* + * Interrupt enable and status bits + */ + +#define TXDE (1 << 0) /* Tx Data empty */ +#define RXDF (1 << 1) /* Rx Data full */ +#define TXFAE (1 << 2) /* Tx FIFO almost empty */ +#define TXFE (1 << 3) /* Tx FIFO empty */ +#define RXFAF (1 << 4) /* Rx FIFO almost full */ +#define RXFF (1 << 5) /* Rx FIFO full */ +#define TXUDR (1 << 6) /* Tx underrun */ +#define RXOVER (1 << 7) /* Rx overrun */ +#define PER (1 << 8) /* Parity error */ +#define FER (1 << 9) /* Frame error */ +#define TCTS (1 << 10) /* Toggle of CTS */ +#define RXTOUT (1 << 11) /* Rx timeout */ +#define BKDONE (1 << 12) /* Break signal done */ +#define ERR (1 << 13) /* AHB error response */ + +#define RX_FIFO_INTS (RXFAF | RXFF | RXOVER | PER | FER | RXTOUT) +#define TX_FIFO_INTS (TXFAE | TXFE | TXUDR) + +struct vt8500_port { + struct uart_port uart; + char name[16]; + struct clk *clk; + unsigned int ier; +}; + +static inline void vt8500_write(struct uart_port *port, unsigned int val, + unsigned int off) +{ + writel(val, port->membase + off); +} + +static inline unsigned int vt8500_read(struct uart_port *port, unsigned int off) +{ + return readl(port->membase + off); +} + +static void vt8500_stop_tx(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = container_of(port, + struct vt8500_port, + uart); + + vt8500_port->ier &= ~TX_FIFO_INTS; + vt8500_write(port, vt8500_port->ier, VT8500_URIER); +} + +static void vt8500_stop_rx(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = container_of(port, + struct vt8500_port, + uart); + + vt8500_port->ier &= ~RX_FIFO_INTS; + vt8500_write(port, vt8500_port->ier, VT8500_URIER); +} + +static void vt8500_enable_ms(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = container_of(port, + struct vt8500_port, + uart); + + vt8500_port->ier |= TCTS; + vt8500_write(port, vt8500_port->ier, VT8500_URIER); +} + +static void handle_rx(struct uart_port *port) +{ + struct tty_struct *tty = tty_port_tty_get(&port->state->port); + if (!tty) { + /* Discard data: no tty available */ + int count = (vt8500_read(port, VT8500_URFIDX) & 0x1f00) >> 8; + u16 ch; + while (count--) + ch = readw(port->membase + VT8500_RXFIFO); + return; + } + + /* + * Handle overrun + */ + if ((vt8500_read(port, VT8500_URISR) & RXOVER)) { + port->icount.overrun++; + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + } + + /* and now the main RX loop */ + while (vt8500_read(port, VT8500_URFIDX) & 0x1f00) { + unsigned int c; + char flag = TTY_NORMAL; + + c = readw(port->membase + VT8500_RXFIFO) & 0x3ff; + + /* Mask conditions we're ignorning. */ + c &= ~port->read_status_mask; + + if (c & FER) { + port->icount.frame++; + flag = TTY_FRAME; + } else if (c & PER) { + port->icount.parity++; + flag = TTY_PARITY; + } + port->icount.rx++; + + if (!uart_handle_sysrq_char(port, c)) + tty_insert_flip_char(tty, c, flag); + } + + tty_flip_buffer_push(tty); + tty_kref_put(tty); +} + +static void handle_tx(struct uart_port *port) +{ + struct circ_buf *xmit = &port->state->xmit; + + if (port->x_char) { + writeb(port->x_char, port->membase + VT8500_TXFIFO); + port->icount.tx++; + port->x_char = 0; + } + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + vt8500_stop_tx(port); + return; + } + + while ((vt8500_read(port, VT8500_URFIDX) & 0x1f) < 16) { + if (uart_circ_empty(xmit)) + break; + + writeb(xmit->buf[xmit->tail], port->membase + VT8500_TXFIFO); + + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) + vt8500_stop_tx(port); +} + +static void vt8500_start_tx(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = container_of(port, + struct vt8500_port, + uart); + + vt8500_port->ier &= ~TX_FIFO_INTS; + vt8500_write(port, vt8500_port->ier, VT8500_URIER); + handle_tx(port); + vt8500_port->ier |= TX_FIFO_INTS; + vt8500_write(port, vt8500_port->ier, VT8500_URIER); +} + +static void handle_delta_cts(struct uart_port *port) +{ + port->icount.cts++; + wake_up_interruptible(&port->state->port.delta_msr_wait); +} + +static irqreturn_t vt8500_irq(int irq, void *dev_id) +{ + struct uart_port *port = dev_id; + unsigned long isr; + + spin_lock(&port->lock); + isr = vt8500_read(port, VT8500_URISR); + + /* Acknowledge active status bits */ + vt8500_write(port, isr, VT8500_URISR); + + if (isr & RX_FIFO_INTS) + handle_rx(port); + if (isr & TX_FIFO_INTS) + handle_tx(port); + if (isr & TCTS) + handle_delta_cts(port); + + spin_unlock(&port->lock); + + return IRQ_HANDLED; +} + +static unsigned int vt8500_tx_empty(struct uart_port *port) +{ + return (vt8500_read(port, VT8500_URFIDX) & 0x1f) < 16 ? + TIOCSER_TEMT : 0; +} + +static unsigned int vt8500_get_mctrl(struct uart_port *port) +{ + unsigned int usr; + + usr = vt8500_read(port, VT8500_URUSR); + if (usr & (1 << 4)) + return TIOCM_CTS; + else + return 0; +} + +static void vt8500_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} + +static void vt8500_break_ctl(struct uart_port *port, int break_ctl) +{ + if (break_ctl) + vt8500_write(port, vt8500_read(port, VT8500_URLCR) | (1 << 9), + VT8500_URLCR); +} + +static int vt8500_set_baud_rate(struct uart_port *port, unsigned int baud) +{ + unsigned long div; + unsigned int loops = 1000; + + div = vt8500_read(port, VT8500_URDIV) & ~(0x3ff); + + if (unlikely((baud < 900) || (baud > 921600))) + div |= 7; + else + div |= (921600 / baud) - 1; + + while ((vt8500_read(port, VT8500_URUSR) & (1 << 5)) && --loops) + cpu_relax(); + vt8500_write(port, div, VT8500_URDIV); + + return baud; +} + +static int vt8500_startup(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = + container_of(port, struct vt8500_port, uart); + int ret; + + snprintf(vt8500_port->name, sizeof(vt8500_port->name), + "vt8500_serial%d", port->line); + + ret = request_irq(port->irq, vt8500_irq, IRQF_TRIGGER_HIGH, + vt8500_port->name, port); + if (unlikely(ret)) + return ret; + + vt8500_write(port, 0x03, VT8500_URLCR); /* enable TX & RX */ + + return 0; +} + +static void vt8500_shutdown(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = + container_of(port, struct vt8500_port, uart); + + vt8500_port->ier = 0; + + /* disable interrupts and FIFOs */ + vt8500_write(&vt8500_port->uart, 0, VT8500_URIER); + vt8500_write(&vt8500_port->uart, 0x880, VT8500_URFCR); + free_irq(port->irq, port); +} + +static void vt8500_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct vt8500_port *vt8500_port = + container_of(port, struct vt8500_port, uart); + unsigned long flags; + unsigned int baud, lcr; + unsigned int loops = 1000; + + spin_lock_irqsave(&port->lock, flags); + + /* calculate and set baud rate */ + baud = uart_get_baud_rate(port, termios, old, 900, 921600); + baud = vt8500_set_baud_rate(port, baud); + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); + + /* calculate parity */ + lcr = vt8500_read(&vt8500_port->uart, VT8500_URLCR); + lcr &= ~((1 << 5) | (1 << 4)); + if (termios->c_cflag & PARENB) { + lcr |= (1 << 4); + termios->c_cflag &= ~CMSPAR; + if (termios->c_cflag & PARODD) + lcr |= (1 << 5); + } + + /* calculate bits per char */ + lcr &= ~(1 << 2); + switch (termios->c_cflag & CSIZE) { + case CS7: + break; + case CS8: + default: + lcr |= (1 << 2); + termios->c_cflag &= ~CSIZE; + termios->c_cflag |= CS8; + break; + } + + /* calculate stop bits */ + lcr &= ~(1 << 3); + if (termios->c_cflag & CSTOPB) + lcr |= (1 << 3); + + /* set parity, bits per char, and stop bit */ + vt8500_write(&vt8500_port->uart, lcr, VT8500_URLCR); + + /* Configure status bits to ignore based on termio flags. */ + port->read_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->read_status_mask = FER | PER; + + uart_update_timeout(port, termios->c_cflag, baud); + + /* Reset FIFOs */ + vt8500_write(&vt8500_port->uart, 0x88c, VT8500_URFCR); + while ((vt8500_read(&vt8500_port->uart, VT8500_URFCR) & 0xc) + && --loops) + cpu_relax(); + + /* Every possible FIFO-related interrupt */ + vt8500_port->ier = RX_FIFO_INTS | TX_FIFO_INTS; + + /* + * CTS flow control + */ + if (UART_ENABLE_MS(&vt8500_port->uart, termios->c_cflag)) + vt8500_port->ier |= TCTS; + + vt8500_write(&vt8500_port->uart, 0x881, VT8500_URFCR); + vt8500_write(&vt8500_port->uart, vt8500_port->ier, VT8500_URIER); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *vt8500_type(struct uart_port *port) +{ + struct vt8500_port *vt8500_port = + container_of(port, struct vt8500_port, uart); + return vt8500_port->name; +} + +static void vt8500_release_port(struct uart_port *port) +{ +} + +static int vt8500_request_port(struct uart_port *port) +{ + return 0; +} + +static void vt8500_config_port(struct uart_port *port, int flags) +{ + port->type = PORT_VT8500; +} + +static int vt8500_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + if (unlikely(ser->type != PORT_UNKNOWN && ser->type != PORT_VT8500)) + return -EINVAL; + if (unlikely(port->irq != ser->irq)) + return -EINVAL; + return 0; +} + +static struct vt8500_port *vt8500_uart_ports[4]; +static struct uart_driver vt8500_uart_driver; + +#ifdef CONFIG_SERIAL_VT8500_CONSOLE + +static inline void wait_for_xmitr(struct uart_port *port) +{ + unsigned int status, tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + do { + status = vt8500_read(port, VT8500_URFIDX); + + if (--tmout == 0) + break; + udelay(1); + } while (status & 0x10); +} + +static void vt8500_console_putchar(struct uart_port *port, int c) +{ + wait_for_xmitr(port); + writeb(c, port->membase + VT8500_TXFIFO); +} + +static void vt8500_console_write(struct console *co, const char *s, + unsigned int count) +{ + struct vt8500_port *vt8500_port = vt8500_uart_ports[co->index]; + unsigned long ier; + + BUG_ON(co->index < 0 || co->index >= vt8500_uart_driver.nr); + + ier = vt8500_read(&vt8500_port->uart, VT8500_URIER); + vt8500_write(&vt8500_port->uart, VT8500_URIER, 0); + + uart_console_write(&vt8500_port->uart, s, count, + vt8500_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and switch back to FIFO + */ + wait_for_xmitr(&vt8500_port->uart); + vt8500_write(&vt8500_port->uart, VT8500_URIER, ier); +} + +static int __init vt8500_console_setup(struct console *co, char *options) +{ + struct vt8500_port *vt8500_port; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (unlikely(co->index >= vt8500_uart_driver.nr || co->index < 0)) + return -ENXIO; + + vt8500_port = vt8500_uart_ports[co->index]; + + if (!vt8500_port) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(&vt8500_port->uart, + co, baud, parity, bits, flow); +} + +static struct console vt8500_console = { + .name = "ttyWMT", + .write = vt8500_console_write, + .device = uart_console_device, + .setup = vt8500_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &vt8500_uart_driver, +}; + +#define VT8500_CONSOLE (&vt8500_console) + +#else +#define VT8500_CONSOLE NULL +#endif + +static struct uart_ops vt8500_uart_pops = { + .tx_empty = vt8500_tx_empty, + .set_mctrl = vt8500_set_mctrl, + .get_mctrl = vt8500_get_mctrl, + .stop_tx = vt8500_stop_tx, + .start_tx = vt8500_start_tx, + .stop_rx = vt8500_stop_rx, + .enable_ms = vt8500_enable_ms, + .break_ctl = vt8500_break_ctl, + .startup = vt8500_startup, + .shutdown = vt8500_shutdown, + .set_termios = vt8500_set_termios, + .type = vt8500_type, + .release_port = vt8500_release_port, + .request_port = vt8500_request_port, + .config_port = vt8500_config_port, + .verify_port = vt8500_verify_port, +}; + +static struct uart_driver vt8500_uart_driver = { + .owner = THIS_MODULE, + .driver_name = "vt8500_serial", + .dev_name = "ttyWMT", + .nr = 6, + .cons = VT8500_CONSOLE, +}; + +static int __init vt8500_serial_probe(struct platform_device *pdev) +{ + struct vt8500_port *vt8500_port; + struct resource *mmres, *irqres; + int ret; + + mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0); + irqres = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!mmres || !irqres) + return -ENODEV; + + vt8500_port = kzalloc(sizeof(struct vt8500_port), GFP_KERNEL); + if (!vt8500_port) + return -ENOMEM; + + vt8500_port->uart.type = PORT_VT8500; + vt8500_port->uart.iotype = UPIO_MEM; + vt8500_port->uart.mapbase = mmres->start; + vt8500_port->uart.irq = irqres->start; + vt8500_port->uart.fifosize = 16; + vt8500_port->uart.ops = &vt8500_uart_pops; + vt8500_port->uart.line = pdev->id; + vt8500_port->uart.dev = &pdev->dev; + vt8500_port->uart.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF; + vt8500_port->uart.uartclk = 24000000; + + snprintf(vt8500_port->name, sizeof(vt8500_port->name), + "VT8500 UART%d", pdev->id); + + vt8500_port->uart.membase = ioremap(mmres->start, + mmres->end - mmres->start + 1); + if (!vt8500_port->uart.membase) { + ret = -ENOMEM; + goto err; + } + + vt8500_uart_ports[pdev->id] = vt8500_port; + + uart_add_one_port(&vt8500_uart_driver, &vt8500_port->uart); + + platform_set_drvdata(pdev, vt8500_port); + + return 0; + +err: + kfree(vt8500_port); + return ret; +} + +static int __devexit vt8500_serial_remove(struct platform_device *pdev) +{ + struct vt8500_port *vt8500_port = platform_get_drvdata(pdev); + + platform_set_drvdata(pdev, NULL); + uart_remove_one_port(&vt8500_uart_driver, &vt8500_port->uart); + kfree(vt8500_port); + + return 0; +} + +static struct platform_driver vt8500_platform_driver = { + .probe = vt8500_serial_probe, + .remove = vt8500_serial_remove, + .driver = { + .name = "vt8500_serial", + .owner = THIS_MODULE, + }, +}; + +static int __init vt8500_serial_init(void) +{ + int ret; + + ret = uart_register_driver(&vt8500_uart_driver); + if (unlikely(ret)) + return ret; + + ret = platform_driver_register(&vt8500_platform_driver); + + if (unlikely(ret)) + uart_unregister_driver(&vt8500_uart_driver); + + return ret; +} + +static void __exit vt8500_serial_exit(void) +{ +#ifdef CONFIG_SERIAL_VT8500_CONSOLE + unregister_console(&vt8500_console); +#endif + platform_driver_unregister(&vt8500_platform_driver); + uart_unregister_driver(&vt8500_uart_driver); +} + +module_init(vt8500_serial_init); +module_exit(vt8500_serial_exit); + +MODULE_AUTHOR("Alexey Charkov <alchark@gmail.com>"); +MODULE_DESCRIPTION("Driver for vt8500 serial device"); +MODULE_LICENSE("GPL"); |