1 files changed, 86 insertions, 1 deletions

diff --git a/drivers/net/wireless/ti/wl18xx/acx.c b/drivers/net/wireless/ti/wl18xx/acx.c
index 72840e23bf59..a169bb5a5dbf 100644
--- a/drivers/net/wireless/ti/wl18xx/acx.c
+++ b/drivers/net/wireless/ti/wl18xx/acx.c
@@ -75,7 +75,7 @@ int wl18xx_acx_set_checksum_state(struct wl1271 *wl)
 
 	acx->checksum_state = CHECKSUM_OFFLOAD_ENABLED;
 
-	ret = wl1271_cmd_configure(wl, ACX_CHECKSUM_CONFIG, acx, sizeof(*acx));
+	ret = wl1271_cmd_configure(wl, ACX_CSUM_CONFIG, acx, sizeof(*acx));
 	if (ret < 0) {
 		wl1271_warning("failed to set Tx checksum state: %d", ret);
 		goto out;
@@ -109,3 +109,88 @@ out:
 	kfree(acx);
 	return ret;
 }
+
+int wl18xx_acx_peer_ht_operation_mode(struct wl1271 *wl, u8 hlid, bool wide)
+{
+	struct wlcore_peer_ht_operation_mode *acx;
+	int ret;
+
+	wl1271_debug(DEBUG_ACX, "acx peer ht operation mode hlid %d bw %d",
+		     hlid, wide);
+
+	acx = kzalloc(sizeof(*acx), GFP_KERNEL);
+	if (!acx) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	acx->hlid = hlid;
+	acx->bandwidth = wide ? WLCORE_BANDWIDTH_40MHZ : WLCORE_BANDWIDTH_20MHZ;
+
+	ret = wl1271_cmd_configure(wl, ACX_PEER_HT_OPERATION_MODE_CFG, acx,
+				   sizeof(*acx));
+
+	if (ret < 0) {
+		wl1271_warning("acx peer ht operation mode failed: %d", ret);
+		goto out;
+	}
+
+out:
+	kfree(acx);
+	return ret;
+
+}
+
+/*
+ * this command is basically the same as wl1271_acx_ht_capabilities,
+ * with the addition of supported rates. they should be unified in
+ * the next fw api change
+ */
+int wl18xx_acx_set_peer_cap(struct wl1271 *wl,
+			    struct ieee80211_sta_ht_cap *ht_cap,
+			    bool allow_ht_operation,
+			    u32 rate_set, u8 hlid)
+{
+	struct wlcore_acx_peer_cap *acx;
+	int ret = 0;
+	u32 ht_capabilites = 0;
+
+	wl1271_debug(DEBUG_ACX,
+		     "acx set cap ht_supp: %d ht_cap: %d rates: 0x%x",
+		     ht_cap->ht_supported, ht_cap->cap, rate_set);
+
+	acx = kzalloc(sizeof(*acx), GFP_KERNEL);
+	if (!acx) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (allow_ht_operation && ht_cap->ht_supported) {
+		/* no need to translate capabilities - use the spec values */
+		ht_capabilites = ht_cap->cap;
+
+		/*
+		 * this bit is not employed by the spec but only by FW to
+		 * indicate peer HT support
+		 */
+		ht_capabilites |= WL12XX_HT_CAP_HT_OPERATION;
+
+		/* get data from A-MPDU parameters field */
+		acx->ampdu_max_length = ht_cap->ampdu_factor;
+		acx->ampdu_min_spacing = ht_cap->ampdu_density;
+	}
+
+	acx->hlid = hlid;
+	acx->ht_capabilites = cpu_to_le32(ht_capabilites);
+	acx->supported_rates = cpu_to_le32(rate_set);
+
+	ret = wl1271_cmd_configure(wl, ACX_PEER_CAP, acx, sizeof(*acx));
+	if (ret < 0) {
+		wl1271_warning("acx ht capabilities setting failed: %d", ret);
+		goto out;
+	}
+
+out:
+	kfree(acx);
+	return ret;
+}