diff options
Diffstat (limited to 'drivers/mtd/spi-nor/core.c')
-rw-r--r-- | drivers/mtd/spi-nor/core.c | 556 |
1 files changed, 304 insertions, 252 deletions
diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c index cc08bd707378..04ea180118e3 100644 --- a/drivers/mtd/spi-nor/core.c +++ b/drivers/mtd/spi-nor/core.c @@ -1952,6 +1952,7 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len, struct spi_nor *nor = mtd_to_spi_nor(mtd); size_t page_offset, page_remain, i; ssize_t ret; + u32 page_size = nor->params->page_size; dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len); @@ -1968,16 +1969,15 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len, * calculated with an AND operation. On the other cases we * need to do a modulus operation (more expensive). */ - if (is_power_of_2(nor->page_size)) { - page_offset = addr & (nor->page_size - 1); + if (is_power_of_2(page_size)) { + page_offset = addr & (page_size - 1); } else { uint64_t aux = addr; - page_offset = do_div(aux, nor->page_size); + page_offset = do_div(aux, page_size); } /* the size of data remaining on the first page */ - page_remain = min_t(size_t, - nor->page_size - page_offset, len - i); + page_remain = min_t(size_t, page_size - page_offset, len - i); addr = spi_nor_convert_addr(nor, addr); @@ -2115,7 +2115,7 @@ static int spi_nor_spimem_check_op(struct spi_nor *nor, */ op->addr.nbytes = 4; if (!spi_mem_supports_op(nor->spimem, op)) { - if (nor->mtd.size > SZ_16M) + if (nor->params->size > SZ_16M) return -EOPNOTSUPP; /* If flash size <= 16MB, 3 address bytes are sufficient */ @@ -2141,7 +2141,7 @@ static int spi_nor_spimem_check_readop(struct spi_nor *nor, struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(read->opcode, 0), SPI_MEM_OP_ADDR(3, 0, 0), SPI_MEM_OP_DUMMY(1, 0), - SPI_MEM_OP_DATA_IN(1, NULL, 0)); + SPI_MEM_OP_DATA_IN(2, NULL, 0)); spi_nor_spimem_setup_op(nor, &op, read->proto); @@ -2167,7 +2167,7 @@ static int spi_nor_spimem_check_pp(struct spi_nor *nor, struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(pp->opcode, 0), SPI_MEM_OP_ADDR(3, 0, 0), SPI_MEM_OP_NO_DUMMY, - SPI_MEM_OP_DATA_OUT(1, NULL, 0)); + SPI_MEM_OP_DATA_OUT(2, NULL, 0)); spi_nor_spimem_setup_op(nor, &op, pp->proto); @@ -2484,13 +2484,61 @@ static int spi_nor_default_setup(struct spi_nor *nor, return 0; } +static int spi_nor_set_addr_width(struct spi_nor *nor) +{ + if (nor->addr_width) { + /* already configured from SFDP */ + } else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) { + /* + * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So + * in this protocol an odd address width cannot be used because + * then the address phase would only span a cycle and a half. + * Half a cycle would be left over. We would then have to start + * the dummy phase in the middle of a cycle and so too the data + * phase, and we will end the transaction with half a cycle left + * over. + * + * Force all 8D-8D-8D flashes to use an address width of 4 to + * avoid this situation. + */ + nor->addr_width = 4; + } else if (nor->info->addr_width) { + nor->addr_width = nor->info->addr_width; + } else { + nor->addr_width = 3; + } + + if (nor->addr_width == 3 && nor->params->size > 0x1000000) { + /* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_width = 4; + } + + if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) { + dev_dbg(nor->dev, "address width is too large: %u\n", + nor->addr_width); + return -EINVAL; + } + + /* Set 4byte opcodes when possible. */ + if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES && + !(nor->flags & SNOR_F_HAS_4BAIT)) + spi_nor_set_4byte_opcodes(nor); + + return 0; +} + static int spi_nor_setup(struct spi_nor *nor, const struct spi_nor_hwcaps *hwcaps) { - if (!nor->params->setup) - return 0; + int ret; - return nor->params->setup(nor, hwcaps); + if (nor->params->setup) { + ret = nor->params->setup(nor, hwcaps); + if (ret) + return ret; + } + + return spi_nor_set_addr_width(nor); } /** @@ -2509,107 +2557,50 @@ static void spi_nor_manufacturer_init_params(struct spi_nor *nor) } /** - * spi_nor_sfdp_init_params() - Initialize the flash's parameters and settings - * based on JESD216 SFDP standard. - * @nor: pointer to a 'struct spi_nor'. - * - * The method has a roll-back mechanism: in case the SFDP parsing fails, the - * legacy flash parameters and settings will be restored. - */ -static void spi_nor_sfdp_init_params(struct spi_nor *nor) -{ - struct spi_nor_flash_parameter sfdp_params; - - memcpy(&sfdp_params, nor->params, sizeof(sfdp_params)); - - if (spi_nor_parse_sfdp(nor)) { - memcpy(nor->params, &sfdp_params, sizeof(*nor->params)); - nor->addr_width = 0; - nor->flags &= ~SNOR_F_4B_OPCODES; - } -} - -/** - * spi_nor_info_init_params() - Initialize the flash's parameters and settings - * based on nor->info data. + * spi_nor_no_sfdp_init_params() - Initialize the flash's parameters and + * settings based on nor->info->sfdp_flags. This method should be called only by + * flashes that do not define SFDP tables. If the flash supports SFDP but the + * information is wrong and the settings from this function can not be retrieved + * by parsing SFDP, one should instead use the fixup hooks and update the wrong + * bits. * @nor: pointer to a 'struct spi_nor'. */ -static void spi_nor_info_init_params(struct spi_nor *nor) +static void spi_nor_no_sfdp_init_params(struct spi_nor *nor) { struct spi_nor_flash_parameter *params = nor->params; struct spi_nor_erase_map *map = ¶ms->erase_map; - const struct flash_info *info = nor->info; - struct device_node *np = spi_nor_get_flash_node(nor); + const u8 no_sfdp_flags = nor->info->no_sfdp_flags; u8 i, erase_mask; - /* Initialize default flash parameters and settings. */ - params->quad_enable = spi_nor_sr2_bit1_quad_enable; - params->set_4byte_addr_mode = spansion_set_4byte_addr_mode; - params->setup = spi_nor_default_setup; - params->otp.org = &info->otp_org; - - /* Default to 16-bit Write Status (01h) Command */ - nor->flags |= SNOR_F_HAS_16BIT_SR; - - /* Set SPI NOR sizes. */ - params->writesize = 1; - params->size = (u64)info->sector_size * info->n_sectors; - params->page_size = info->page_size; - - if (!(info->flags & SPI_NOR_NO_FR)) { - /* Default to Fast Read for DT and non-DT platform devices. */ - params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST; - - /* Mask out Fast Read if not requested at DT instantiation. */ - if (np && !of_property_read_bool(np, "m25p,fast-read")) - params->hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST; - } - - /* (Fast) Read settings. */ - params->hwcaps.mask |= SNOR_HWCAPS_READ; - spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ], - 0, 0, SPINOR_OP_READ, - SNOR_PROTO_1_1_1); - - if (params->hwcaps.mask & SNOR_HWCAPS_READ_FAST) - spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_FAST], - 0, 8, SPINOR_OP_READ_FAST, - SNOR_PROTO_1_1_1); - - if (info->flags & SPI_NOR_DUAL_READ) { + if (no_sfdp_flags & SPI_NOR_DUAL_READ) { params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2; spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_2], 0, 8, SPINOR_OP_READ_1_1_2, SNOR_PROTO_1_1_2); } - if (info->flags & SPI_NOR_QUAD_READ) { + if (no_sfdp_flags & SPI_NOR_QUAD_READ) { params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4; spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_4], 0, 8, SPINOR_OP_READ_1_1_4, SNOR_PROTO_1_1_4); } - if (info->flags & SPI_NOR_OCTAL_READ) { + if (no_sfdp_flags & SPI_NOR_OCTAL_READ) { params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_8; spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_8], 0, 8, SPINOR_OP_READ_1_1_8, SNOR_PROTO_1_1_8); } - if (info->flags & SPI_NOR_OCTAL_DTR_READ) { + if (no_sfdp_flags & SPI_NOR_OCTAL_DTR_READ) { params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR; spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_8_8_8_DTR], 0, 20, SPINOR_OP_READ_FAST, SNOR_PROTO_8_8_8_DTR); } - /* Page Program settings. */ - params->hwcaps.mask |= SNOR_HWCAPS_PP; - spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP], - SPINOR_OP_PP, SNOR_PROTO_1_1_1); - - if (info->flags & SPI_NOR_OCTAL_DTR_PP) { + if (no_sfdp_flags & SPI_NOR_OCTAL_DTR_PP) { params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR; /* * Since xSPI Page Program opcode is backward compatible with @@ -2625,52 +2616,111 @@ static void spi_nor_info_init_params(struct spi_nor *nor) */ erase_mask = 0; i = 0; - if (info->flags & SECT_4K_PMC) { + if (no_sfdp_flags & SECT_4K_PMC) { erase_mask |= BIT(i); spi_nor_set_erase_type(&map->erase_type[i], 4096u, SPINOR_OP_BE_4K_PMC); i++; - } else if (info->flags & SECT_4K) { + } else if (no_sfdp_flags & SECT_4K) { erase_mask |= BIT(i); spi_nor_set_erase_type(&map->erase_type[i], 4096u, SPINOR_OP_BE_4K); i++; } erase_mask |= BIT(i); - spi_nor_set_erase_type(&map->erase_type[i], info->sector_size, + spi_nor_set_erase_type(&map->erase_type[i], nor->info->sector_size, SPINOR_OP_SE); spi_nor_init_uniform_erase_map(map, erase_mask, params->size); } /** - * spi_nor_post_sfdp_fixups() - Updates the flash's parameters and settings - * after SFDP has been parsed (is also called for SPI NORs that do not - * support RDSFDP). + * spi_nor_init_flags() - Initialize NOR flags for settings that are not defined + * in the JESD216 SFDP standard, thus can not be retrieved when parsing SFDP. * @nor: pointer to a 'struct spi_nor' - * - * Typically used to tweak various parameters that could not be extracted by - * other means (i.e. when information provided by the SFDP/flash_info tables - * are incomplete or wrong). */ -static void spi_nor_post_sfdp_fixups(struct spi_nor *nor) +static void spi_nor_init_flags(struct spi_nor *nor) { - if (nor->manufacturer && nor->manufacturer->fixups && - nor->manufacturer->fixups->post_sfdp) - nor->manufacturer->fixups->post_sfdp(nor); + struct device_node *np = spi_nor_get_flash_node(nor); + const u16 flags = nor->info->flags; + + if (of_property_read_bool(np, "broken-flash-reset")) + nor->flags |= SNOR_F_BROKEN_RESET; - if (nor->info->fixups && nor->info->fixups->post_sfdp) - nor->info->fixups->post_sfdp(nor); + if (flags & SPI_NOR_SWP_IS_VOLATILE) + nor->flags |= SNOR_F_SWP_IS_VOLATILE; + + if (flags & SPI_NOR_HAS_LOCK) + nor->flags |= SNOR_F_HAS_LOCK; + + if (flags & SPI_NOR_HAS_TB) { + nor->flags |= SNOR_F_HAS_SR_TB; + if (flags & SPI_NOR_TB_SR_BIT6) + nor->flags |= SNOR_F_HAS_SR_TB_BIT6; + } + + if (flags & SPI_NOR_4BIT_BP) { + nor->flags |= SNOR_F_HAS_4BIT_BP; + if (flags & SPI_NOR_BP3_SR_BIT6) + nor->flags |= SNOR_F_HAS_SR_BP3_BIT6; + } + + if (flags & NO_CHIP_ERASE) + nor->flags |= SNOR_F_NO_OP_CHIP_ERASE; + + if (flags & USE_CLSR) + nor->flags |= SNOR_F_USE_CLSR; + + if (flags & USE_FSR) + nor->flags |= SNOR_F_USE_FSR; + + /* + * Make sure the XSR_RDY flag is set before calling + * spi_nor_wait_till_ready(). Xilinx S3AN share MFR + * with Atmel SPI NOR. + */ + if (flags & SPI_NOR_XSR_RDY) + nor->flags |= SNOR_F_READY_XSR_RDY; +} + +/** + * spi_nor_init_fixup_flags() - Initialize NOR flags for settings that can not + * be discovered by SFDP for this particular flash because the SFDP table that + * indicates this support is not defined in the flash. In case the table for + * this support is defined but has wrong values, one should instead use a + * post_sfdp() hook to set the SNOR_F equivalent flag. + * @nor: pointer to a 'struct spi_nor' + */ +static void spi_nor_init_fixup_flags(struct spi_nor *nor) +{ + const u8 fixup_flags = nor->info->fixup_flags; + + if (fixup_flags & SPI_NOR_4B_OPCODES) + nor->flags |= SNOR_F_4B_OPCODES; + + if (fixup_flags & SPI_NOR_IO_MODE_EN_VOLATILE) + nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE; } /** * spi_nor_late_init_params() - Late initialization of default flash parameters. * @nor: pointer to a 'struct spi_nor' * - * Used to set default flash parameters and settings when the ->default_init() - * hook or the SFDP parser let voids. + * Used to initialize flash parameters that are not declared in the JESD216 + * SFDP standard, or where SFDP tables are not defined at all. + * Will replace the spi_nor_manufacturer_init_params() method. */ static void spi_nor_late_init_params(struct spi_nor *nor) { + if (nor->manufacturer && nor->manufacturer->fixups && + nor->manufacturer->fixups->late_init) + nor->manufacturer->fixups->late_init(nor); + + if (nor->info->fixups && nor->info->fixups->late_init) + nor->info->fixups->late_init(nor); + + spi_nor_init_flags(nor); + spi_nor_init_fixup_flags(nor); + /* * NOR protection support. When locking_ops are not provided, we pick * the default ones. @@ -2680,6 +2730,99 @@ static void spi_nor_late_init_params(struct spi_nor *nor) } /** + * spi_nor_sfdp_init_params_deprecated() - Deprecated way of initializing flash + * parameters and settings based on JESD216 SFDP standard. + * @nor: pointer to a 'struct spi_nor'. + * + * The method has a roll-back mechanism: in case the SFDP parsing fails, the + * legacy flash parameters and settings will be restored. + */ +static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor) +{ + struct spi_nor_flash_parameter sfdp_params; + + memcpy(&sfdp_params, nor->params, sizeof(sfdp_params)); + + if (spi_nor_parse_sfdp(nor)) { + memcpy(nor->params, &sfdp_params, sizeof(*nor->params)); + nor->addr_width = 0; + nor->flags &= ~SNOR_F_4B_OPCODES; + } +} + +/** + * spi_nor_init_params_deprecated() - Deprecated way of initializing flash + * parameters and settings. + * @nor: pointer to a 'struct spi_nor'. + * + * The method assumes that flash doesn't support SFDP so it initializes flash + * parameters in spi_nor_no_sfdp_init_params() which later on can be overwritten + * when parsing SFDP, if supported. + */ +static void spi_nor_init_params_deprecated(struct spi_nor *nor) +{ + spi_nor_no_sfdp_init_params(nor); + + spi_nor_manufacturer_init_params(nor); + + if (nor->info->no_sfdp_flags & (SPI_NOR_DUAL_READ | + SPI_NOR_QUAD_READ | + SPI_NOR_OCTAL_READ | + SPI_NOR_OCTAL_DTR_READ)) + spi_nor_sfdp_init_params_deprecated(nor); +} + +/** + * spi_nor_init_default_params() - Default initialization of flash parameters + * and settings. Done for all flashes, regardless is they define SFDP tables + * or not. + * @nor: pointer to a 'struct spi_nor'. + */ +static void spi_nor_init_default_params(struct spi_nor *nor) +{ + struct spi_nor_flash_parameter *params = nor->params; + const struct flash_info *info = nor->info; + struct device_node *np = spi_nor_get_flash_node(nor); + + params->quad_enable = spi_nor_sr2_bit1_quad_enable; + params->set_4byte_addr_mode = spansion_set_4byte_addr_mode; + params->setup = spi_nor_default_setup; + params->otp.org = &info->otp_org; + + /* Default to 16-bit Write Status (01h) Command */ + nor->flags |= SNOR_F_HAS_16BIT_SR; + + /* Set SPI NOR sizes. */ + params->writesize = 1; + params->size = (u64)info->sector_size * info->n_sectors; + params->page_size = info->page_size; + + if (!(info->flags & SPI_NOR_NO_FR)) { + /* Default to Fast Read for DT and non-DT platform devices. */ + params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST; + + /* Mask out Fast Read if not requested at DT instantiation. */ + if (np && !of_property_read_bool(np, "m25p,fast-read")) + params->hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST; + } + + /* (Fast) Read settings. */ + params->hwcaps.mask |= SNOR_HWCAPS_READ; + spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ], + 0, 0, SPINOR_OP_READ, + SNOR_PROTO_1_1_1); + + if (params->hwcaps.mask & SNOR_HWCAPS_READ_FAST) + spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_FAST], + 0, 8, SPINOR_OP_READ_FAST, + SNOR_PROTO_1_1_1); + /* Page Program settings. */ + params->hwcaps.mask |= SNOR_HWCAPS_PP; + spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP], + SPINOR_OP_PP, SNOR_PROTO_1_1_1); +} + +/** * spi_nor_init_params() - Initialize the flash's parameters and settings. * @nor: pointer to a 'struct spi_nor'. * @@ -2699,39 +2842,44 @@ static void spi_nor_late_init_params(struct spi_nor *nor) * which can be overwritten by: * 3/ SFDP flash parameters initialization. JESD216 SFDP is a standard and * should be more accurate that the above. - * spi_nor_sfdp_init_params() + * spi_nor_parse_sfdp() or spi_nor_no_sfdp_init_params() * * Please note that there is a ->post_bfpt() fixup hook that can overwrite * the flash parameters and settings immediately after parsing the Basic * Flash Parameter Table. + * spi_nor_post_sfdp_fixups() is called after the SFDP tables are parsed. + * It is used to tweak various flash parameters when information provided + * by the SFDP tables are wrong. * * which can be overwritten by: - * 4/ Post SFDP flash parameters initialization. Used to tweak various - * parameters that could not be extracted by other means (i.e. when - * information provided by the SFDP/flash_info tables are incomplete or - * wrong). - * spi_nor_post_sfdp_fixups() - * - * 5/ Late default flash parameters initialization, used when the - * ->default_init() hook or the SFDP parser do not set specific params. + * 4/ Late flash parameters initialization, used to initialize flash + * parameters that are not declared in the JESD216 SFDP standard, or where SFDP + * tables are not defined at all. * spi_nor_late_init_params() + * + * Return: 0 on success, -errno otherwise. */ static int spi_nor_init_params(struct spi_nor *nor) { + int ret; + nor->params = devm_kzalloc(nor->dev, sizeof(*nor->params), GFP_KERNEL); if (!nor->params) return -ENOMEM; - spi_nor_info_init_params(nor); - - spi_nor_manufacturer_init_params(nor); + spi_nor_init_default_params(nor); - if ((nor->info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | - SPI_NOR_OCTAL_READ | SPI_NOR_OCTAL_DTR_READ)) && - !(nor->info->flags & SPI_NOR_SKIP_SFDP)) - spi_nor_sfdp_init_params(nor); - - spi_nor_post_sfdp_fixups(nor); + if (nor->info->parse_sfdp) { + ret = spi_nor_parse_sfdp(nor); + if (ret) { + dev_err(nor->dev, "BFPT parsing failed. Please consider using SPI_NOR_SKIP_SFDP when declaring the flash\n"); + return ret; + } + } else if (nor->info->no_sfdp_flags & SPI_NOR_SKIP_SFDP) { + spi_nor_no_sfdp_init_params(nor); + } else { + spi_nor_init_params_deprecated(nor); + } spi_nor_late_init_params(nor); @@ -2978,59 +3126,6 @@ static const struct flash_info *spi_nor_match_id(struct spi_nor *nor, return NULL; } -static int spi_nor_set_addr_width(struct spi_nor *nor) -{ - if (nor->addr_width) { - /* already configured from SFDP */ - } else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) { - /* - * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So - * in this protocol an odd address width cannot be used because - * then the address phase would only span a cycle and a half. - * Half a cycle would be left over. We would then have to start - * the dummy phase in the middle of a cycle and so too the data - * phase, and we will end the transaction with half a cycle left - * over. - * - * Force all 8D-8D-8D flashes to use an address width of 4 to - * avoid this situation. - */ - nor->addr_width = 4; - } else if (nor->info->addr_width) { - nor->addr_width = nor->info->addr_width; - } else { - nor->addr_width = 3; - } - - if (nor->addr_width == 3 && nor->mtd.size > 0x1000000) { - /* enable 4-byte addressing if the device exceeds 16MiB */ - nor->addr_width = 4; - } - - if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) { - dev_dbg(nor->dev, "address width is too large: %u\n", - nor->addr_width); - return -EINVAL; - } - - /* Set 4byte opcodes when possible. */ - if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES && - !(nor->flags & SNOR_F_HAS_4BAIT)) - spi_nor_set_4byte_opcodes(nor); - - return 0; -} - -static void spi_nor_debugfs_init(struct spi_nor *nor, - const struct flash_info *info) -{ - struct mtd_info *mtd = &nor->mtd; - - mtd->dbg.partname = info->name; - mtd->dbg.partid = devm_kasprintf(nor->dev, GFP_KERNEL, "spi-nor:%*phN", - info->id_len, info->id); -} - static const struct flash_info *spi_nor_get_flash_info(struct spi_nor *nor, const char *name) { @@ -3071,13 +3166,41 @@ static const struct flash_info *spi_nor_get_flash_info(struct spi_nor *nor, return info; } +static void spi_nor_set_mtd_info(struct spi_nor *nor) +{ + struct mtd_info *mtd = &nor->mtd; + struct device *dev = nor->dev; + + spi_nor_set_mtd_locking_ops(nor); + spi_nor_set_mtd_otp_ops(nor); + + mtd->dev.parent = dev; + if (!mtd->name) + mtd->name = dev_name(dev); + mtd->type = MTD_NORFLASH; + mtd->flags = MTD_CAP_NORFLASH; + if (nor->info->flags & SPI_NOR_NO_ERASE) + mtd->flags |= MTD_NO_ERASE; + mtd->writesize = nor->params->writesize; + mtd->writebufsize = nor->params->page_size; + mtd->size = nor->params->size; + mtd->_erase = spi_nor_erase; + mtd->_read = spi_nor_read; + /* Might be already set by some SST flashes. */ + if (!mtd->_write) + mtd->_write = spi_nor_write; + mtd->_suspend = spi_nor_suspend; + mtd->_resume = spi_nor_resume; + mtd->_get_device = spi_nor_get_device; + mtd->_put_device = spi_nor_put_device; +} + int spi_nor_scan(struct spi_nor *nor, const char *name, const struct spi_nor_hwcaps *hwcaps) { const struct flash_info *info; struct device *dev = nor->dev; struct mtd_info *mtd = &nor->mtd; - struct device_node *np = spi_nor_get_flash_node(nor); int ret; int i; @@ -3094,7 +3217,7 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, * We need the bounce buffer early to read/write registers when going * through the spi-mem layer (buffers have to be DMA-able). * For spi-mem drivers, we'll reallocate a new buffer if - * nor->page_size turns out to be greater than PAGE_SIZE (which + * nor->params->page_size turns out to be greater than PAGE_SIZE (which * shouldn't happen before long since NOR pages are usually less * than 1KB) after spi_nor_scan() returns. */ @@ -3110,102 +3233,31 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, nor->info = info; - spi_nor_debugfs_init(nor, info); - mutex_init(&nor->lock); - /* - * Make sure the XSR_RDY flag is set before calling - * spi_nor_wait_till_ready(). Xilinx S3AN share MFR - * with Atmel SPI NOR. - */ - if (info->flags & SPI_NOR_XSR_RDY) - nor->flags |= SNOR_F_READY_XSR_RDY; - - if (info->flags & SPI_NOR_HAS_LOCK) - nor->flags |= SNOR_F_HAS_LOCK; - - mtd->_write = spi_nor_write; - /* Init flash parameters based on flash_info struct and SFDP */ ret = spi_nor_init_params(nor); if (ret) return ret; - if (!mtd->name) - mtd->name = dev_name(dev); - mtd->priv = nor; - mtd->type = MTD_NORFLASH; - mtd->writesize = nor->params->writesize; - mtd->flags = MTD_CAP_NORFLASH; - mtd->size = nor->params->size; - mtd->_erase = spi_nor_erase; - mtd->_read = spi_nor_read; - mtd->_suspend = spi_nor_suspend; - mtd->_resume = spi_nor_resume; - mtd->_get_device = spi_nor_get_device; - mtd->_put_device = spi_nor_put_device; - - if (info->flags & USE_FSR) - nor->flags |= SNOR_F_USE_FSR; - if (info->flags & SPI_NOR_HAS_TB) { - nor->flags |= SNOR_F_HAS_SR_TB; - if (info->flags & SPI_NOR_TB_SR_BIT6) - nor->flags |= SNOR_F_HAS_SR_TB_BIT6; - } - - if (info->flags & NO_CHIP_ERASE) - nor->flags |= SNOR_F_NO_OP_CHIP_ERASE; - if (info->flags & USE_CLSR) - nor->flags |= SNOR_F_USE_CLSR; - if (info->flags & SPI_NOR_SWP_IS_VOLATILE) - nor->flags |= SNOR_F_SWP_IS_VOLATILE; - - if (info->flags & SPI_NOR_4BIT_BP) { - nor->flags |= SNOR_F_HAS_4BIT_BP; - if (info->flags & SPI_NOR_BP3_SR_BIT6) - nor->flags |= SNOR_F_HAS_SR_BP3_BIT6; - } - - if (info->flags & SPI_NOR_NO_ERASE) - mtd->flags |= MTD_NO_ERASE; - - mtd->dev.parent = dev; - nor->page_size = nor->params->page_size; - mtd->writebufsize = nor->page_size; - - if (of_property_read_bool(np, "broken-flash-reset")) - nor->flags |= SNOR_F_BROKEN_RESET; - /* * Configure the SPI memory: * - select op codes for (Fast) Read, Page Program and Sector Erase. * - set the number of dummy cycles (mode cycles + wait states). * - set the SPI protocols for register and memory accesses. + * - set the address width. */ ret = spi_nor_setup(nor, hwcaps); if (ret) return ret; - if (info->flags & SPI_NOR_4B_OPCODES) - nor->flags |= SNOR_F_4B_OPCODES; - - if (info->flags & SPI_NOR_IO_MODE_EN_VOLATILE) - nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE; - - ret = spi_nor_set_addr_width(nor); - if (ret) - return ret; - - spi_nor_register_locking_ops(nor); - /* Send all the required SPI flash commands to initialize device */ ret = spi_nor_init(nor); if (ret) return ret; - /* Configure OTP parameters and ops */ - spi_nor_otp_init(nor); + /* No mtd_info fields should be used up to this point. */ + spi_nor_set_mtd_info(nor); dev_info(dev, "%s (%lld Kbytes)\n", info->name, (long long)mtd->size >> 10); @@ -3238,7 +3290,7 @@ static int spi_nor_create_read_dirmap(struct spi_nor *nor) SPI_MEM_OP_DUMMY(nor->read_dummy, 0), SPI_MEM_OP_DATA_IN(0, NULL, 0)), .offset = 0, - .length = nor->mtd.size, + .length = nor->params->size, }; struct spi_mem_op *op = &info.op_tmpl; @@ -3269,7 +3321,7 @@ static int spi_nor_create_write_dirmap(struct spi_nor *nor) SPI_MEM_OP_NO_DUMMY, SPI_MEM_OP_DATA_OUT(0, NULL, 0)), .offset = 0, - .length = nor->mtd.size, + .length = nor->params->size, }; struct spi_mem_op *op = &info.op_tmpl; @@ -3341,8 +3393,8 @@ static int spi_nor_probe(struct spi_mem *spimem) * and add this logic so that if anyone ever adds support for such * a NOR we don't end up with buffer overflows. */ - if (nor->page_size > PAGE_SIZE) { - nor->bouncebuf_size = nor->page_size; + if (nor->params->page_size > PAGE_SIZE) { + nor->bouncebuf_size = nor->params->page_size; devm_kfree(nor->dev, nor->bouncebuf); nor->bouncebuf = devm_kmalloc(nor->dev, nor->bouncebuf_size, @@ -3389,8 +3441,8 @@ static void spi_nor_shutdown(struct spi_mem *spimem) * encourage new users to add support to the spi-nor library, and simply bind * against a generic string here (e.g., "jedec,spi-nor"). * - * Many flash names are kept here in this list (as well as in spi-nor.c) to - * keep them available as module aliases for existing platforms. + * Many flash names are kept here in this list to keep them available + * as module aliases for existing platforms. */ static const struct spi_device_id spi_nor_dev_ids[] = { /* |