diff options
Diffstat (limited to 'arch/blackfin/mach-bf527/include/mach')
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/anomaly.h | 22 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/bf527.h | 120 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/defBF52x_base.h | 225 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/gpio.h | 96 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/portmux.h | 3 |
5 files changed, 206 insertions, 260 deletions
diff --git a/arch/blackfin/mach-bf527/include/mach/anomaly.h b/arch/blackfin/mach-bf527/include/mach/anomaly.h index 02040df8ec80..9358afa05c90 100644 --- a/arch/blackfin/mach-bf527/include/mach/anomaly.h +++ b/arch/blackfin/mach-bf527/include/mach/anomaly.h @@ -5,13 +5,13 @@ * and can be replaced with that version at any time * DO NOT EDIT THIS FILE * - * Copyright 2004-2009 Analog Devices Inc. + * Copyright 2004-2010 Analog Devices Inc. * Licensed under the ADI BSD license. * https://docs.blackfin.uclinux.org/doku.php?id=adi_bsd */ /* This file should be up to date with: - * - Revision D, 08/14/2009; ADSP-BF526 Blackfin Processor Anomaly List + * - Revision E, 03/15/2010; ADSP-BF526 Blackfin Processor Anomaly List * - Revision G, 08/25/2009; ADSP-BF527 Blackfin Processor Anomaly List */ @@ -41,7 +41,7 @@ /* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */ #define ANOMALY_05000074 (1) /* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */ -#define ANOMALY_05000119 (1) /* note: brokenness is noted in documentation, not anomaly sheet */ +#define ANOMALY_05000119 (1) /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ #define ANOMALY_05000122 (1) /* False Hardware Error from an Access in the Shadow of a Conditional Branch */ @@ -168,6 +168,8 @@ #define ANOMALY_05000431 (1) /* bfrom_SysControl() Does Not Clear SIC_IWR1 Before Executing PLL Programming Sequence */ #define ANOMALY_05000432 (_ANOMALY_BF526(< 1)) +/* SW Breakpoints Ignored Upon Return From Lockbox Authentication */ +#define ANOMALY_05000434 (1) /* Certain SIC Registers are not Reset After Soft or Core Double Fault Reset */ #define ANOMALY_05000435 (_ANOMALY_BF526_BF527(< 1, >= 0)) /* Preboot Cannot be Used to Alter the PLL_DIV Register */ @@ -204,10 +206,22 @@ #define ANOMALY_05000467 (1) /* PLL Latches Incorrect Settings During Reset */ #define ANOMALY_05000469 (1) +/* Incorrect Default MSEL Value in PLL_CTL */ +#define ANOMALY_05000472 (_ANOMALY_BF526(>= 0)) /* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */ #define ANOMALY_05000473 (1) +/* Possible Lockup Condition whem Modifying PLL from External Memory */ +#define ANOMALY_05000475 (1) /* TESTSET Instruction Cannot Be Interrupted */ #define ANOMALY_05000477 (1) +/* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */ +#define ANOMALY_05000481 (1) +/* Possible USB Data Corruption When Multiple Endpoints Are Accessed by the Core */ +#define ANOMALY_05000483 (1) +/* PLL_CTL Change Using bfrom_SysControl() Can Result in Processor Overclocking */ +#define ANOMALY_05000485 (_ANOMALY_BF526_BF527(< 2, < 3)) +/* IFLUSH sucks at life */ +#define ANOMALY_05000491 (1) /* Anomalies that don't exist on this proc */ #define ANOMALY_05000099 (0) @@ -223,6 +237,7 @@ #define ANOMALY_05000198 (0) #define ANOMALY_05000202 (0) #define ANOMALY_05000215 (0) +#define ANOMALY_05000219 (0) #define ANOMALY_05000220 (0) #define ANOMALY_05000227 (0) #define ANOMALY_05000230 (0) @@ -259,6 +274,5 @@ #define ANOMALY_05000447 (0) #define ANOMALY_05000448 (0) #define ANOMALY_05000474 (0) -#define ANOMALY_05000475 (0) #endif diff --git a/arch/blackfin/mach-bf527/include/mach/bf527.h b/arch/blackfin/mach-bf527/include/mach/bf527.h index ff68c8897087..8ff155b34f64 100644 --- a/arch/blackfin/mach-bf527/include/mach/bf527.h +++ b/arch/blackfin/mach-bf527/include/mach/bf527.h @@ -85,6 +85,126 @@ #define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO) +/**************************** Hysteresis Settings ****************************/ + +#ifdef CONFIG_BFIN_HYSTERESIS_CONTROL +#ifdef CONFIG_GPIO_HYST_PORTF_0_7 +#define HYST_PORTF_0_7 (1 << 0) +#else +#define HYST_PORTF_0_7 (0 << 0) +#endif +#ifdef CONFIG_GPIO_HYST_PORTF_8_9 +#define HYST_PORTF_8_9 (1 << 2) +#else +#define HYST_PORTF_8_9 (0 << 2) +#endif +#ifdef CONFIG_GPIO_HYST_PORTF_10 +#define HYST_PORTF_10 (1 << 4) +#else +#define HYST_PORTF_10 (0 << 4) +#endif +#ifdef CONFIG_GPIO_HYST_PORTF_11 +#define HYST_PORTF_11 (1 << 6) +#else +#define HYST_PORTF_11 (0 << 6) +#endif +#ifdef CONFIG_GPIO_HYST_PORTF_12_13 +#define HYST_PORTF_12_13 (1 << 8) +#else +#define HYST_PORTF_12_13 (0 << 8) +#endif +#ifdef CONFIG_GPIO_HYST_PORTF_14_15 +#define HYST_PORTF_14_15 (1 << 10) +#else +#define HYST_PORTF_14_15 (0 << 10) +#endif + +#define HYST_PORTF_0_15 (HYST_PORTF_0_7 | HYST_PORTF_8_9 | HYST_PORTF_10 | \ + HYST_PORTF_11 | HYST_PORTF_12_13 | HYST_PORTF_14_15) + +#ifdef CONFIG_GPIO_HYST_PORTG_0 +#define HYST_PORTG_0 (1 << 0) +#else +#define HYST_PORTG_0 (0 << 0) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_1_4 +#define HYST_PORTG_1_4 (1 << 2) +#else +#define HYST_PORTG_1_4 (0 << 2) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_5_6 +#define HYST_PORTG_5_6 (1 << 4) +#else +#define HYST_PORTG_5_6 (0 << 4) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_7_8 +#define HYST_PORTG_7_8 (1 << 6) +#else +#define HYST_PORTG_7_8 (0 << 6) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_9 +#define HYST_PORTG_9 (1 << 8) +#else +#define HYST_PORTG_9 (0 << 8) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_10 +#define HYST_PORTG_10 (1 << 10) +#else +#define HYST_PORTG_10 (0 << 10) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_11_13 +#define HYST_PORTG_11_13 (1 << 12) +#else +#define HYST_PORTG_11_13 (0 << 12) +#endif +#ifdef CONFIG_GPIO_HYST_PORTG_14_15 +#define HYST_PORTG_14_15 (1 << 14) +#else +#define HYST_PORTG_14_15 (0 << 14) +#endif + +#define HYST_PORTG_0_15 (HYST_PORTG_0 | HYST_PORTG_1_4 | HYST_PORTG_5_6 | \ + HYST_PORTG_7_8 | HYST_PORTG_9 | HYST_PORTG_10 | \ + HYST_PORTG_11_13 | HYST_PORTG_14_15) + +#ifdef CONFIG_GPIO_HYST_PORTH_0_7 +#define HYST_PORTH_0_7 (1 << 0) +#else +#define HYST_PORTH_0_7 (0 << 0) +#endif +#ifdef CONFIG_GPIO_HYST_PORTH_8 +#define HYST_PORTH_8 (1 << 2) +#else +#define HYST_PORTH_8 (0 << 2) +#endif +#ifdef CONFIG_GPIO_HYST_PORTH_9_15 +#define HYST_PORTH_9_15 (1 << 4) +#else +#define HYST_PORTH_9_15 (0 << 4) +#endif + +#define HYST_PORTH_0_15 (HYST_PORTH_0_7 | HYST_PORTH_8 | HYST_PORTH_9_15) + +#ifdef CONFIG_NONEGPIO_HYST_TMR0_FS1_PPICLK +#define HYST_TMR0_FS1_PPICLK (1 << 0) +#else +#define HYST_TMR0_FS1_PPICLK (0 << 0) +#endif +#ifdef CONFIG_NONEGPIO_HYST_NMI_RST_BMODE +#define HYST_NMI_RST_BMODE (1 << 2) +#else +#define HYST_NMI_RST_BMODE (0 << 2) +#endif +#ifdef CONFIG_NONEGPIO_HYST_JTAG +#define HYST_JTAG (1 << 4) +#else +#define HYST_JTAG (0 << 4) +#endif + +#define HYST_NONEGPIO (HYST_TMR0_FS1_PPICLK | HYST_NMI_RST_BMODE | HYST_JTAG) +#define HYST_NONEGPIO_MASK (0x3F) +#endif /* CONFIG_BFIN_HYSTERESIS_CONTROL */ + #ifdef CONFIG_BF527 #define CPU "BF527" #define CPUID 0x27e0 diff --git a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h index 8b18b5359210..5f97f01fcda6 100644 --- a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h +++ b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h @@ -458,22 +458,22 @@ /* Two-Wire Interface (0xFFC01400 - 0xFFC014FF) */ #define TWI0_REGBASE 0xFFC01400 -#define TWI_CLKDIV 0xFFC01400 /* Serial Clock Divider Register */ -#define TWI_CONTROL 0xFFC01404 /* TWI Control Register */ -#define TWI_SLAVE_CTL 0xFFC01408 /* Slave Mode Control Register */ -#define TWI_SLAVE_STAT 0xFFC0140C /* Slave Mode Status Register */ -#define TWI_SLAVE_ADDR 0xFFC01410 /* Slave Mode Address Register */ -#define TWI_MASTER_CTL 0xFFC01414 /* Master Mode Control Register */ -#define TWI_MASTER_STAT 0xFFC01418 /* Master Mode Status Register */ -#define TWI_MASTER_ADDR 0xFFC0141C /* Master Mode Address Register */ -#define TWI_INT_STAT 0xFFC01420 /* TWI Interrupt Status Register */ -#define TWI_INT_MASK 0xFFC01424 /* TWI Master Interrupt Mask Register */ -#define TWI_FIFO_CTL 0xFFC01428 /* FIFO Control Register */ -#define TWI_FIFO_STAT 0xFFC0142C /* FIFO Status Register */ -#define TWI_XMT_DATA8 0xFFC01480 /* FIFO Transmit Data Single Byte Register */ -#define TWI_XMT_DATA16 0xFFC01484 /* FIFO Transmit Data Double Byte Register */ -#define TWI_RCV_DATA8 0xFFC01488 /* FIFO Receive Data Single Byte Register */ -#define TWI_RCV_DATA16 0xFFC0148C /* FIFO Receive Data Double Byte Register */ +#define TWI0_CLKDIV 0xFFC01400 /* Serial Clock Divider Register */ +#define TWI0_CONTROL 0xFFC01404 /* TWI Control Register */ +#define TWI0_SLAVE_CTL 0xFFC01408 /* Slave Mode Control Register */ +#define TWI0_SLAVE_STAT 0xFFC0140C /* Slave Mode Status Register */ +#define TWI0_SLAVE_ADDR 0xFFC01410 /* Slave Mode Address Register */ +#define TWI0_MASTER_CTL 0xFFC01414 /* Master Mode Control Register */ +#define TWI0_MASTER_STAT 0xFFC01418 /* Master Mode Status Register */ +#define TWI0_MASTER_ADDR 0xFFC0141C /* Master Mode Address Register */ +#define TWI0_INT_STAT 0xFFC01420 /* TWI Interrupt Status Register */ +#define TWI0_INT_MASK 0xFFC01424 /* TWI Master Interrupt Mask Register */ +#define TWI0_FIFO_CTL 0xFFC01428 /* FIFO Control Register */ +#define TWI0_FIFO_STAT 0xFFC0142C /* FIFO Status Register */ +#define TWI0_XMT_DATA8 0xFFC01480 /* FIFO Transmit Data Single Byte Register */ +#define TWI0_XMT_DATA16 0xFFC01484 /* FIFO Transmit Data Double Byte Register */ +#define TWI0_RCV_DATA8 0xFFC01488 /* FIFO Receive Data Single Byte Register */ +#define TWI0_RCV_DATA16 0xFFC0148C /* FIFO Receive Data Double Byte Register */ /* General Purpose I/O Port G (0xFFC01500 - 0xFFC015FF) */ @@ -1328,7 +1328,7 @@ #define TWI_ENA 0x0080 /* TWI Enable */ #define SCCB 0x0200 /* SCCB Compatibility Enable */ -/* TWI_SLAVE_CTRL Masks */ +/* TWI_SLAVE_CTL Masks */ #define SEN 0x0001 /* Slave Enable */ #define SADD_LEN 0x0002 /* Slave Address Length */ #define STDVAL 0x0004 /* Slave Transmit Data Valid */ @@ -1339,7 +1339,7 @@ #define SDIR 0x0001 /* Slave Transfer Direction (Transmit/Receive*) */ #define GCALL 0x0002 /* General Call Indicator */ -/* TWI_MASTER_CTRL Masks */ +/* TWI_MASTER_CTL Masks */ #define MEN 0x0001 /* Master Mode Enable */ #define MADD_LEN 0x0002 /* Master Address Length */ #define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */ @@ -1589,114 +1589,6 @@ #define HOST_COUNT_TIMEOUT 0x7ff /* Host Timeout count */ -/* Bit masks for CNT_CONFIG */ - -#define CNTE 0x1 /* Counter Enable */ -#define nCNTE 0x0 -#define DEBE 0x2 /* Debounce Enable */ -#define nDEBE 0x0 -#define CDGINV 0x10 /* CDG Pin Polarity Invert */ -#define nCDGINV 0x0 -#define CUDINV 0x20 /* CUD Pin Polarity Invert */ -#define nCUDINV 0x0 -#define CZMINV 0x40 /* CZM Pin Polarity Invert */ -#define nCZMINV 0x0 -#define CNTMODE 0x700 /* Counter Operating Mode */ -#define ZMZC 0x800 /* CZM Zeroes Counter Enable */ -#define nZMZC 0x0 -#define BNDMODE 0x3000 /* Boundary register Mode */ -#define INPDIS 0x8000 /* CUG and CDG Input Disable */ -#define nINPDIS 0x0 - -/* Bit masks for CNT_IMASK */ - -#define ICIE 0x1 /* Illegal Gray/Binary Code Interrupt Enable */ -#define nICIE 0x0 -#define UCIE 0x2 /* Up count Interrupt Enable */ -#define nUCIE 0x0 -#define DCIE 0x4 /* Down count Interrupt Enable */ -#define nDCIE 0x0 -#define MINCIE 0x8 /* Min Count Interrupt Enable */ -#define nMINCIE 0x0 -#define MAXCIE 0x10 /* Max Count Interrupt Enable */ -#define nMAXCIE 0x0 -#define COV31IE 0x20 /* Bit 31 Overflow Interrupt Enable */ -#define nCOV31IE 0x0 -#define COV15IE 0x40 /* Bit 15 Overflow Interrupt Enable */ -#define nCOV15IE 0x0 -#define CZEROIE 0x80 /* Count to Zero Interrupt Enable */ -#define nCZEROIE 0x0 -#define CZMIE 0x100 /* CZM Pin Interrupt Enable */ -#define nCZMIE 0x0 -#define CZMEIE 0x200 /* CZM Error Interrupt Enable */ -#define nCZMEIE 0x0 -#define CZMZIE 0x400 /* CZM Zeroes Counter Interrupt Enable */ -#define nCZMZIE 0x0 - -/* Bit masks for CNT_STATUS */ - -#define ICII 0x1 /* Illegal Gray/Binary Code Interrupt Identifier */ -#define nICII 0x0 -#define UCII 0x2 /* Up count Interrupt Identifier */ -#define nUCII 0x0 -#define DCII 0x4 /* Down count Interrupt Identifier */ -#define nDCII 0x0 -#define MINCII 0x8 /* Min Count Interrupt Identifier */ -#define nMINCII 0x0 -#define MAXCII 0x10 /* Max Count Interrupt Identifier */ -#define nMAXCII 0x0 -#define COV31II 0x20 /* Bit 31 Overflow Interrupt Identifier */ -#define nCOV31II 0x0 -#define COV15II 0x40 /* Bit 15 Overflow Interrupt Identifier */ -#define nCOV15II 0x0 -#define CZEROII 0x80 /* Count to Zero Interrupt Identifier */ -#define nCZEROII 0x0 -#define CZMII 0x100 /* CZM Pin Interrupt Identifier */ -#define nCZMII 0x0 -#define CZMEII 0x200 /* CZM Error Interrupt Identifier */ -#define nCZMEII 0x0 -#define CZMZII 0x400 /* CZM Zeroes Counter Interrupt Identifier */ -#define nCZMZII 0x0 - -/* Bit masks for CNT_COMMAND */ - -#define W1LCNT 0xf /* Load Counter Register */ -#define W1LMIN 0xf0 /* Load Min Register */ -#define W1LMAX 0xf00 /* Load Max Register */ -#define W1ZMONCE 0x1000 /* Enable CZM Clear Counter Once */ -#define nW1ZMONCE 0x0 - -/* Bit masks for CNT_DEBOUNCE */ - -#define DPRESCALE 0xf /* Load Counter Register */ - -/* CNT_COMMAND bit field options */ - -#define W1LCNT_ZERO 0x0001 /* write 1 to load CNT_COUNTER with zero */ -#define W1LCNT_MIN 0x0004 /* write 1 to load CNT_COUNTER from CNT_MIN */ -#define W1LCNT_MAX 0x0008 /* write 1 to load CNT_COUNTER from CNT_MAX */ - -#define W1LMIN_ZERO 0x0010 /* write 1 to load CNT_MIN with zero */ -#define W1LMIN_CNT 0x0020 /* write 1 to load CNT_MIN from CNT_COUNTER */ -#define W1LMIN_MAX 0x0080 /* write 1 to load CNT_MIN from CNT_MAX */ - -#define W1LMAX_ZERO 0x0100 /* write 1 to load CNT_MAX with zero */ -#define W1LMAX_CNT 0x0200 /* write 1 to load CNT_MAX from CNT_COUNTER */ -#define W1LMAX_MIN 0x0400 /* write 1 to load CNT_MAX from CNT_MIN */ - -/* CNT_CONFIG bit field options */ - -#define CNTMODE_QUADENC 0x0000 /* quadrature encoder mode */ -#define CNTMODE_BINENC 0x0100 /* binary encoder mode */ -#define CNTMODE_UDCNT 0x0200 /* up/down counter mode */ -#define CNTMODE_DIRCNT 0x0400 /* direction counter mode */ -#define CNTMODE_DIRTMR 0x0500 /* direction timer mode */ - -#define BNDMODE_COMP 0x0000 /* boundary compare mode */ -#define BNDMODE_ZERO 0x1000 /* boundary compare and zero mode */ -#define BNDMODE_CAPT 0x2000 /* boundary capture mode */ -#define BNDMODE_AEXT 0x3000 /* boundary auto-extend mode */ - /* Bit masks for SECURE_SYSSWT */ #define EMUDABL 0x1 /* Emulation Disable. */ @@ -1738,85 +1630,4 @@ #define nAFEXIT 0x0 #define SECSTAT 0xe0 /* Secure Status */ -/* Bit masks for NFC_CTL */ - -#define WR_DLY 0xf /* Write Strobe Delay */ -#define RD_DLY 0xf0 /* Read Strobe Delay */ -#define NWIDTH 0x100 /* NAND Data Width */ -#define nNWIDTH 0x0 -#define PG_SIZE 0x200 /* Page Size */ -#define nPG_SIZE 0x0 - -/* Bit masks for NFC_STAT */ - -#define NBUSY 0x1 /* Not Busy */ -#define nNBUSY 0x0 -#define WB_FULL 0x2 /* Write Buffer Full */ -#define nWB_FULL 0x0 -#define PG_WR_STAT 0x4 /* Page Write Pending */ -#define nPG_WR_STAT 0x0 -#define PG_RD_STAT 0x8 /* Page Read Pending */ -#define nPG_RD_STAT 0x0 -#define WB_EMPTY 0x10 /* Write Buffer Empty */ -#define nWB_EMPTY 0x0 - -/* Bit masks for NFC_IRQSTAT */ - -#define NBUSYIRQ 0x1 /* Not Busy IRQ */ -#define nNBUSYIRQ 0x0 -#define WB_OVF 0x2 /* Write Buffer Overflow */ -#define nWB_OVF 0x0 -#define WB_EDGE 0x4 /* Write Buffer Edge Detect */ -#define nWB_EDGE 0x0 -#define RD_RDY 0x8 /* Read Data Ready */ -#define nRD_RDY 0x0 -#define WR_DONE 0x10 /* Page Write Done */ -#define nWR_DONE 0x0 - -/* Bit masks for NFC_IRQMASK */ - -#define MASK_BUSYIRQ 0x1 /* Mask Not Busy IRQ */ -#define nMASK_BUSYIRQ 0x0 -#define MASK_WBOVF 0x2 /* Mask Write Buffer Overflow */ -#define nMASK_WBOVF 0x0 -#define MASK_WBEMPTY 0x4 /* Mask Write Buffer Empty */ -#define nMASK_WBEMPTY 0x0 -#define MASK_RDRDY 0x8 /* Mask Read Data Ready */ -#define nMASK_RDRDY 0x0 -#define MASK_WRDONE 0x10 /* Mask Write Done */ -#define nMASK_WRDONE 0x0 - -/* Bit masks for NFC_RST */ - -#define ECC_RST 0x1 /* ECC (and NFC counters) Reset */ -#define nECC_RST 0x0 - -/* Bit masks for NFC_PGCTL */ - -#define PG_RD_START 0x1 /* Page Read Start */ -#define nPG_RD_START 0x0 -#define PG_WR_START 0x2 /* Page Write Start */ -#define nPG_WR_START 0x0 - -/* Bit masks for NFC_ECC0 */ - -#define ECC0 0x7ff /* Parity Calculation Result0 */ - -/* Bit masks for NFC_ECC1 */ - -#define ECC1 0x7ff /* Parity Calculation Result1 */ - -/* Bit masks for NFC_ECC2 */ - -#define ECC2 0x7ff /* Parity Calculation Result2 */ - -/* Bit masks for NFC_ECC3 */ - -#define ECC3 0x7ff /* Parity Calculation Result3 */ - -/* Bit masks for NFC_COUNT */ - -#define ECCCNT 0x3ff /* Transfer Count */ - - #endif /* _DEF_BF52X_H */ diff --git a/arch/blackfin/mach-bf527/include/mach/gpio.h b/arch/blackfin/mach-bf527/include/mach/gpio.h index 104bff85290d..f80c2995efdb 100644 --- a/arch/blackfin/mach-bf527/include/mach/gpio.h +++ b/arch/blackfin/mach-bf527/include/mach/gpio.h @@ -9,54 +9,54 @@ #define MAX_BLACKFIN_GPIOS 48 -#define GPIO_PF0 0 -#define GPIO_PF1 1 -#define GPIO_PF2 2 -#define GPIO_PF3 3 -#define GPIO_PF4 4 -#define GPIO_PF5 5 -#define GPIO_PF6 6 -#define GPIO_PF7 7 -#define GPIO_PF8 8 -#define GPIO_PF9 9 -#define GPIO_PF10 10 -#define GPIO_PF11 11 -#define GPIO_PF12 12 -#define GPIO_PF13 13 -#define GPIO_PF14 14 -#define GPIO_PF15 15 -#define GPIO_PG0 16 -#define GPIO_PG1 17 -#define GPIO_PG2 18 -#define GPIO_PG3 19 -#define GPIO_PG4 20 -#define GPIO_PG5 21 -#define GPIO_PG6 22 -#define GPIO_PG7 23 -#define GPIO_PG8 24 -#define GPIO_PG9 25 -#define GPIO_PG10 26 -#define GPIO_PG11 27 -#define GPIO_PG12 28 -#define GPIO_PG13 29 -#define GPIO_PG14 30 -#define GPIO_PG15 31 -#define GPIO_PH0 32 -#define GPIO_PH1 33 -#define GPIO_PH2 34 -#define GPIO_PH3 35 -#define GPIO_PH4 36 -#define GPIO_PH5 37 -#define GPIO_PH6 38 -#define GPIO_PH7 39 -#define GPIO_PH8 40 -#define GPIO_PH9 41 -#define GPIO_PH10 42 -#define GPIO_PH11 43 -#define GPIO_PH12 44 -#define GPIO_PH13 45 -#define GPIO_PH14 46 -#define GPIO_PH15 47 +#define GPIO_PF0 0 +#define GPIO_PF1 1 +#define GPIO_PF2 2 +#define GPIO_PF3 3 +#define GPIO_PF4 4 +#define GPIO_PF5 5 +#define GPIO_PF6 6 +#define GPIO_PF7 7 +#define GPIO_PF8 8 +#define GPIO_PF9 9 +#define GPIO_PF10 10 +#define GPIO_PF11 11 +#define GPIO_PF12 12 +#define GPIO_PF13 13 +#define GPIO_PF14 14 +#define GPIO_PF15 15 +#define GPIO_PG0 16 +#define GPIO_PG1 17 +#define GPIO_PG2 18 +#define GPIO_PG3 19 +#define GPIO_PG4 20 +#define GPIO_PG5 21 +#define GPIO_PG6 22 +#define GPIO_PG7 23 +#define GPIO_PG8 24 +#define GPIO_PG9 25 +#define GPIO_PG10 26 +#define GPIO_PG11 27 +#define GPIO_PG12 28 +#define GPIO_PG13 29 +#define GPIO_PG14 30 +#define GPIO_PG15 31 +#define GPIO_PH0 32 +#define GPIO_PH1 33 +#define GPIO_PH2 34 +#define GPIO_PH3 35 +#define GPIO_PH4 36 +#define GPIO_PH5 37 +#define GPIO_PH6 38 +#define GPIO_PH7 39 +#define GPIO_PH8 40 +#define GPIO_PH9 41 +#define GPIO_PH10 42 +#define GPIO_PH11 43 +#define GPIO_PH12 44 +#define GPIO_PH13 45 +#define GPIO_PH14 46 +#define GPIO_PH15 47 #define PORT_F GPIO_PF0 #define PORT_G GPIO_PG0 diff --git a/arch/blackfin/mach-bf527/include/mach/portmux.h b/arch/blackfin/mach-bf527/include/mach/portmux.h index d4518b6f4adf..08bae421f5c9 100644 --- a/arch/blackfin/mach-bf527/include/mach/portmux.h +++ b/arch/blackfin/mach-bf527/include/mach/portmux.h @@ -7,7 +7,7 @@ #ifndef _MACH_PORTMUX_H_ #define _MACH_PORTMUX_H_ -#define MAX_RESOURCES MAX_BLACKFIN_GPIOS +#define MAX_RESOURCES MAX_BLACKFIN_GPIOS #define P_PPI0_D0 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(0)) #define P_PPI0_D1 (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(0)) @@ -79,6 +79,7 @@ #define P_HWAIT (P_DONTCARE) +#define GPIO_DEFAULT_BOOT_SPI_CS GPIO_PG1 #define P_DEFAULT_BOOT_SPI_CS P_SPI0_SSEL1 #define P_SPI0_SS (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0)) |