summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-u300/core.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/mach-u300/core.c')
-rw-r--r--arch/arm/mach-u300/core.c413
1 files changed, 0 insertions, 413 deletions
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
deleted file mode 100644
index a1694d977ec9..000000000000
--- a/arch/arm/mach-u300/core.c
+++ /dev/null
@@ -1,413 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *
- * arch/arm/mach-u300/core.c
- *
- * Copyright (C) 2007-2012 ST-Ericsson SA
- * Core platform support, IRQ handling and device definitions.
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-#include <linux/kernel.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/platform_data/clk-u300.h>
-#include <linux/irqchip.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-#include <linux/clocksource.h>
-#include <linux/clk.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/arch.h>
-
-/*
- * These are the large blocks of memory allocated for I/O.
- * the defines are used for setting up the I/O memory mapping.
- */
-
-/* NAND Flash CS0 */
-#define U300_NAND_CS0_PHYS_BASE 0x80000000
-/* NFIF */
-#define U300_NAND_IF_PHYS_BASE 0x9f800000
-/* ALE, CLE offset for FSMC NAND */
-#define PLAT_NAND_CLE (1 << 16)
-#define PLAT_NAND_ALE (1 << 17)
-/* AHB Peripherals */
-#define U300_AHB_PER_PHYS_BASE 0xa0000000
-#define U300_AHB_PER_VIRT_BASE 0xff010000
-/* FAST Peripherals */
-#define U300_FAST_PER_PHYS_BASE 0xc0000000
-#define U300_FAST_PER_VIRT_BASE 0xff020000
-/* SLOW Peripherals */
-#define U300_SLOW_PER_PHYS_BASE 0xc0010000
-#define U300_SLOW_PER_VIRT_BASE 0xff000000
-/* Boot ROM */
-#define U300_BOOTROM_PHYS_BASE 0xffff0000
-#define U300_BOOTROM_VIRT_BASE 0xffff0000
-/* SEMI config base */
-#define U300_SEMI_CONFIG_BASE 0x2FFE0000
-
-/*
- * AHB peripherals
- */
-
-/* AHB Peripherals Bridge Controller */
-#define U300_AHB_BRIDGE_BASE (U300_AHB_PER_PHYS_BASE+0x0000)
-/* Vectored Interrupt Controller 0, servicing 32 interrupts */
-#define U300_INTCON0_BASE (U300_AHB_PER_PHYS_BASE+0x1000)
-#define U300_INTCON0_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x1000)
-/* Vectored Interrupt Controller 1, servicing 32 interrupts */
-#define U300_INTCON1_BASE (U300_AHB_PER_PHYS_BASE+0x2000)
-#define U300_INTCON1_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x2000)
-/* Memory Stick Pro (MSPRO) controller */
-#define U300_MSPRO_BASE (U300_AHB_PER_PHYS_BASE+0x3000)
-/* EMIF Configuration Area */
-#define U300_EMIF_CFG_BASE (U300_AHB_PER_PHYS_BASE+0x4000)
-
-/*
- * FAST peripherals
- */
-
-/* FAST bridge control */
-#define U300_FAST_BRIDGE_BASE (U300_FAST_PER_PHYS_BASE+0x0000)
-/* MMC/SD controller */
-#define U300_MMCSD_BASE (U300_FAST_PER_PHYS_BASE+0x1000)
-/* PCM I2S0 controller */
-#define U300_PCM_I2S0_BASE (U300_FAST_PER_PHYS_BASE+0x2000)
-/* PCM I2S1 controller */
-#define U300_PCM_I2S1_BASE (U300_FAST_PER_PHYS_BASE+0x3000)
-/* I2C0 controller */
-#define U300_I2C0_BASE (U300_FAST_PER_PHYS_BASE+0x4000)
-/* I2C1 controller */
-#define U300_I2C1_BASE (U300_FAST_PER_PHYS_BASE+0x5000)
-/* SPI controller */
-#define U300_SPI_BASE (U300_FAST_PER_PHYS_BASE+0x6000)
-/* Fast UART1 on U335 only */
-#define U300_UART1_BASE (U300_FAST_PER_PHYS_BASE+0x7000)
-
-/*
- * SLOW peripherals
- */
-
-/* SLOW bridge control */
-#define U300_SLOW_BRIDGE_BASE (U300_SLOW_PER_PHYS_BASE)
-/* SYSCON */
-#define U300_SYSCON_BASE (U300_SLOW_PER_PHYS_BASE+0x1000)
-#define U300_SYSCON_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000)
-/* Watchdog */
-#define U300_WDOG_BASE (U300_SLOW_PER_PHYS_BASE+0x2000)
-/* UART0 */
-#define U300_UART0_BASE (U300_SLOW_PER_PHYS_BASE+0x3000)
-/* APP side special timer */
-#define U300_TIMER_APP_BASE (U300_SLOW_PER_PHYS_BASE+0x4000)
-#define U300_TIMER_APP_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000)
-/* Keypad */
-#define U300_KEYPAD_BASE (U300_SLOW_PER_PHYS_BASE+0x5000)
-/* GPIO */
-#define U300_GPIO_BASE (U300_SLOW_PER_PHYS_BASE+0x6000)
-/* RTC */
-#define U300_RTC_BASE (U300_SLOW_PER_PHYS_BASE+0x7000)
-/* Bus tracer */
-#define U300_BUSTR_BASE (U300_SLOW_PER_PHYS_BASE+0x8000)
-/* Event handler (hardware queue) */
-#define U300_EVHIST_BASE (U300_SLOW_PER_PHYS_BASE+0x9000)
-/* Genric Timer */
-#define U300_TIMER_BASE (U300_SLOW_PER_PHYS_BASE+0xa000)
-/* PPM */
-#define U300_PPM_BASE (U300_SLOW_PER_PHYS_BASE+0xb000)
-
-/*
- * REST peripherals
- */
-
-/* ISP (image signal processor) */
-#define U300_ISP_BASE (0xA0008000)
-/* DMA Controller base */
-#define U300_DMAC_BASE (0xC0020000)
-/* MSL Base */
-#define U300_MSL_BASE (0xc0022000)
-/* APEX Base */
-#define U300_APEX_BASE (0xc0030000)
-/* Video Encoder Base */
-#define U300_VIDEOENC_BASE (0xc0080000)
-/* XGAM Base */
-#define U300_XGAM_BASE (0xd0000000)
-
-/*
- * SYSCON addresses applicable to the core machine.
- */
-
-/* Chip ID register 16bit (R/-) */
-#define U300_SYSCON_CIDR (0x400)
-/* SMCR */
-#define U300_SYSCON_SMCR (0x4d0)
-#define U300_SYSCON_SMCR_FIELD_MASK (0x000e)
-#define U300_SYSCON_SMCR_SEMI_SREFACK_IND (0x0008)
-#define U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE (0x0004)
-#define U300_SYSCON_SMCR_SEMI_EXT_BOOT_MODE_ENABLE (0x0002)
-/* CPU_SW_DBGEN Software Debug Enable 16bit (R/W) */
-#define U300_SYSCON_CSDR (0x4f0)
-#define U300_SYSCON_CSDR_SW_DEBUG_ENABLE (0x0001)
-/* PRINT_CONTROL Print Control 16bit (R/-) */
-#define U300_SYSCON_PCR (0x4f8)
-#define U300_SYSCON_PCR_SERV_IND (0x0001)
-/* BOOT_CONTROL 16bit (R/-) */
-#define U300_SYSCON_BCR (0x4fc)
-#define U300_SYSCON_BCR_ACC_CPU_SUBSYS_VINITHI_IND (0x0400)
-#define U300_SYSCON_BCR_APP_CPU_SUBSYS_VINITHI_IND (0x0200)
-#define U300_SYSCON_BCR_EXTRA_BOOT_OPTION_MASK (0x01FC)
-#define U300_SYSCON_BCR_APP_BOOT_SERV_MASK (0x0003)
-
-static void __iomem *syscon_base;
-
-/*
- * Static I/O mappings that are needed for booting the U300 platforms. The
- * only things we need are the areas where we find the timer, syscon and
- * intcon, since the remaining device drivers will map their own memory
- * physical to virtual as the need arise.
- */
-static struct map_desc u300_io_desc[] __initdata = {
- {
- .virtual = U300_SLOW_PER_VIRT_BASE,
- .pfn = __phys_to_pfn(U300_SLOW_PER_PHYS_BASE),
- .length = SZ_64K,
- .type = MT_DEVICE,
- },
- {
- .virtual = U300_AHB_PER_VIRT_BASE,
- .pfn = __phys_to_pfn(U300_AHB_PER_PHYS_BASE),
- .length = SZ_32K,
- .type = MT_DEVICE,
- },
- {
- .virtual = U300_FAST_PER_VIRT_BASE,
- .pfn = __phys_to_pfn(U300_FAST_PER_PHYS_BASE),
- .length = SZ_32K,
- .type = MT_DEVICE,
- },
-};
-
-static void __init u300_map_io(void)
-{
- iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
-}
-
-static unsigned long pin_pullup_conf[] = {
- PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 1),
-};
-
-static unsigned long pin_highz_conf[] = {
- PIN_CONF_PACKED(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0),
-};
-
-/* Pin control settings */
-static const struct pinctrl_map u300_pinmux_map[] = {
- /* anonymous maps for chip power and EMIFs */
- PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
- PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),
- PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif1"),
- /* per-device maps for MMC/SD, SPI and UART */
- PIN_MAP_MUX_GROUP_DEFAULT("mmci", "pinctrl-u300", NULL, "mmc0"),
- PIN_MAP_MUX_GROUP_DEFAULT("pl022", "pinctrl-u300", NULL, "spi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-u300", NULL, "uart0"),
- /* This pin is used for clock return rather than GPIO */
- PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO APP GPIO 11",
- pin_pullup_conf),
- /* This pin is used for card detect */
- PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO MS INS",
- pin_highz_conf),
-};
-
-struct db_chip {
- u16 chipid;
- const char *name;
-};
-
-/*
- * This is a list of the Digital Baseband chips used in the U300 platform.
- */
-static struct db_chip db_chips[] __initdata = {
- {
- .chipid = 0xb800,
- .name = "DB3000",
- },
- {
- .chipid = 0xc000,
- .name = "DB3100",
- },
- {
- .chipid = 0xc800,
- .name = "DB3150",
- },
- {
- .chipid = 0xd800,
- .name = "DB3200",
- },
- {
- .chipid = 0xe000,
- .name = "DB3250",
- },
- {
- .chipid = 0xe800,
- .name = "DB3210",
- },
- {
- .chipid = 0xf000,
- .name = "DB3350 P1x",
- },
- {
- .chipid = 0xf100,
- .name = "DB3350 P2x",
- },
- {
- .chipid = 0x0000, /* List terminator */
- .name = NULL,
- }
-};
-
-static void __init u300_init_check_chip(void)
-{
-
- u16 val;
- struct db_chip *chip;
- const char *chipname;
- const char unknown[] = "UNKNOWN";
-
- /* Read out and print chip ID */
- val = readw(syscon_base + U300_SYSCON_CIDR);
- /* This is in funky bigendian order... */
- val = (val & 0xFFU) << 8 | (val >> 8);
- chip = db_chips;
- chipname = unknown;
-
- for ( ; chip->chipid; chip++) {
- if (chip->chipid == (val & 0xFF00U)) {
- chipname = chip->name;
- break;
- }
- }
- printk(KERN_INFO "Initializing U300 system on %s baseband chip " \
- "(chip ID 0x%04x)\n", chipname, val);
-
- if ((val & 0xFF00U) != 0xf000 && (val & 0xFF00U) != 0xf100) {
- printk(KERN_ERR "Platform configured for BS335 " \
- " with DB3350 but %s detected, expect problems!",
- chipname);
- }
-}
-
-/* Forward declare this function from the watchdog */
-void coh901327_watchdog_reset(void);
-
-static void u300_restart(enum reboot_mode mode, const char *cmd)
-{
- switch (mode) {
- case REBOOT_SOFT:
- case REBOOT_HARD:
-#ifdef CONFIG_COH901327_WATCHDOG
- coh901327_watchdog_reset();
-#endif
- break;
- default:
- /* Do nothing */
- break;
- }
- /* Wait for system do die/reset. */
- while (1);
-}
-
-/* These are mostly to get the right device names for the clock lookups */
-static struct of_dev_auxdata u300_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("stericsson,pinctrl-u300", U300_SYSCON_BASE,
- "pinctrl-u300", NULL),
- OF_DEV_AUXDATA("stericsson,gpio-coh901", U300_GPIO_BASE,
- "u300-gpio", NULL),
- OF_DEV_AUXDATA("stericsson,coh901327", U300_WDOG_BASE,
- "coh901327_wdog", NULL),
- OF_DEV_AUXDATA("stericsson,coh901331", U300_RTC_BASE,
- "rtc-coh901331", NULL),
- OF_DEV_AUXDATA("stericsson,coh901318", U300_DMAC_BASE,
- "coh901318", NULL),
- OF_DEV_AUXDATA("stericsson,fsmc-nand", U300_NAND_IF_PHYS_BASE,
- "fsmc-nand", NULL),
- OF_DEV_AUXDATA("arm,primecell", U300_UART0_BASE,
- "uart0", NULL),
- OF_DEV_AUXDATA("arm,primecell", U300_UART1_BASE,
- "uart1", NULL),
- OF_DEV_AUXDATA("arm,primecell", U300_SPI_BASE,
- "pl022", NULL),
- OF_DEV_AUXDATA("st,ddci2c", U300_I2C0_BASE,
- "stu300.0", NULL),
- OF_DEV_AUXDATA("st,ddci2c", U300_I2C1_BASE,
- "stu300.1", NULL),
- OF_DEV_AUXDATA("arm,primecell", U300_MMCSD_BASE,
- "mmci", NULL),
- { /* sentinel */ },
-};
-
-static void __init u300_init_irq_dt(void)
-{
- struct device_node *syscon;
- struct clk *clk;
-
- syscon = of_find_node_by_path("/syscon@c0011000");
- if (!syscon) {
- pr_crit("could not find syscon node\n");
- return;
- }
- syscon_base = of_iomap(syscon, 0);
- if (!syscon_base) {
- pr_crit("could not remap syscon\n");
- return;
- }
- /* initialize clocking early, we want to clock the INTCON */
- u300_clk_init(syscon_base);
-
- /* Bootstrap EMIF and SEMI clocks */
- clk = clk_get_sys("pl172", NULL);
- BUG_ON(IS_ERR(clk));
- clk_prepare_enable(clk);
- clk = clk_get_sys("semi", NULL);
- BUG_ON(IS_ERR(clk));
- clk_prepare_enable(clk);
-
- /* Clock the interrupt controller */
- clk = clk_get_sys("intcon", NULL);
- BUG_ON(IS_ERR(clk));
- clk_prepare_enable(clk);
-
- irqchip_init();
-}
-
-static void __init u300_init_machine_dt(void)
-{
- u16 val;
-
- /* Check what platform we run and print some status information */
- u300_init_check_chip();
-
- /* Initialize pinmuxing */
- pinctrl_register_mappings(u300_pinmux_map,
- ARRAY_SIZE(u300_pinmux_map));
-
- of_platform_default_populate(NULL, u300_auxdata_lookup, NULL);
-
- /* Enable SEMI self refresh */
- val = readw(syscon_base + U300_SYSCON_SMCR) |
- U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE;
- writew(val, syscon_base + U300_SYSCON_SMCR);
-}
-
-static const char * u300_board_compat[] = {
- "stericsson,u300",
- NULL,
-};
-
-DT_MACHINE_START(U300_DT, "U300 S335/B335 (Device Tree)")
- .map_io = u300_map_io,
- .init_irq = u300_init_irq_dt,
- .init_time = timer_probe,
- .init_machine = u300_init_machine_dt,
- .restart = u300_restart,
- .dt_compat = u300_board_compat,
-MACHINE_END