diff options
Diffstat (limited to 'arch/arm/common/gic.c')
| -rw-r--r-- | arch/arm/common/gic.c | 40 |
1 files changed, 24 insertions, 16 deletions
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index 772f95f1aecd..e6388dcd8cfa 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -146,9 +146,15 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val) unsigned int shift = (irq % 4) * 8; unsigned int cpu = cpumask_first(mask_val); u32 val; + struct irq_desc *desc; spin_lock(&irq_controller_lock); - irq_desc[irq].node = cpu; + desc = irq_to_desc(irq); + if (desc == NULL) { + spin_unlock(&irq_controller_lock); + return -EINVAL; + } + desc->node = cpu; val = readl(reg) & ~(0xff << shift); val |= 1 << (cpu + shift); writel(val, reg); @@ -210,7 +216,7 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq) void __init gic_dist_init(unsigned int gic_nr, void __iomem *base, unsigned int irq_start) { - unsigned int max_irq, i; + unsigned int gic_irqs, irq_limit, i; u32 cpumask = 1 << smp_processor_id(); if (gic_nr >= MAX_GIC_NR) @@ -226,47 +232,49 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base, /* * Find out how many interrupts are supported. - */ - max_irq = readl(base + GIC_DIST_CTR) & 0x1f; - max_irq = (max_irq + 1) * 32; - - /* * The GIC only supports up to 1020 interrupt sources. - * Limit this to either the architected maximum, or the - * platform maximum. */ - if (max_irq > max(1020, NR_IRQS)) - max_irq = max(1020, NR_IRQS); + gic_irqs = readl(base + GIC_DIST_CTR) & 0x1f; + gic_irqs = (gic_irqs + 1) * 32; + if (gic_irqs > 1020) + gic_irqs = 1020; /* * Set all global interrupts to be level triggered, active low. */ - for (i = 32; i < max_irq; i += 16) + for (i = 32; i < gic_irqs; i += 16) writel(0, base + GIC_DIST_CONFIG + i * 4 / 16); /* * Set all global interrupts to this CPU only. */ - for (i = 32; i < max_irq; i += 4) + for (i = 32; i < gic_irqs; i += 4) writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4); /* * Set priority on all global interrupts. */ - for (i = 32; i < max_irq; i += 4) + for (i = 32; i < gic_irqs; i += 4) writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4); /* * Disable all interrupts. Leave the PPI and SGIs alone * as these enables are banked registers. */ - for (i = 32; i < max_irq; i += 32) + for (i = 32; i < gic_irqs; i += 32) writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32); /* + * Limit number of interrupts registered to the platform maximum + */ + irq_limit = gic_data[gic_nr].irq_offset + gic_irqs; + if (WARN_ON(irq_limit > NR_IRQS)) + irq_limit = NR_IRQS; + + /* * Setup the Linux IRQ subsystem. */ - for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) { + for (i = irq_start; i < irq_limit; i++) { set_irq_chip(i, &gic_chip); set_irq_chip_data(i, &gic_data[gic_nr]); set_irq_handler(i, handle_level_irq); |