diff options
Diffstat (limited to 'arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts')
| -rw-r--r-- | arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 123 |
1 files changed, 123 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts index f05cabd34b8e..15c22b06fc4b 100644 --- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts +++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts @@ -50,6 +50,7 @@ compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40"; aliases { + ethernet0 = &gmac; serial0 = &uart0; }; @@ -57,6 +58,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -84,14 +96,52 @@ wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */ + clocks = <&ccu CLK_OUTA>; + clock-names = "ext_clock"; }; }; +&ahci { + ahci-supply = <®_dldo4>; + phy-supply = <®_eldo3>; + status = "okay"; +}; + +&de { + status = "okay"; +}; + &ehci1 { /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */ status = "okay"; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_rgmii_pins>; + phy-handle = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_dc1sw>; + status = "okay"; +}; + +&gmac_mdio { + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &i2c0 { status = "okay"; @@ -123,6 +173,23 @@ status = "okay"; }; +&pio { + pinctrl-names = "default"; + pinctrl-0 = <&clk_out_a_pin>; + vcc-pa-supply = <®_aldo2>; + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_eldo1>; + vcc-pf-supply = <®_dcdc1>; + vcc-pg-supply = <®_dldo1>; +}; + +®_aldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa"; +}; + ®_aldo3 { regulator-always-on; regulator-min-microvolt = <2700000>; @@ -130,6 +197,12 @@ regulator-name = "avcc"; }; +®_dc1sw { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-gmac-phy"; +}; + ®_dcdc1 { regulator-always-on; regulator-min-microvolt = <3000000>; @@ -164,18 +237,68 @@ regulator-name = "vcc-wifi-io"; }; +/* + * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same + * time, with the two being in sync, to be able to meet maximum power + * consumption during transmits. Since this is not really supported + * right now, just use the two as always on, and we will fix it later. + */ + ®_dldo2 { + regulator-always-on; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-name = "vcc-wifi"; }; +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; +}; + +®_dldo4 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vdd2v5-sata"; +}; + +®_eldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vdd1v2-sata"; +}; + +&tcon_tv0 { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&ccu CLK_OUTA>; + clock-names = "lpo"; + vbat-supply = <®_dldo2>; + vddio-supply = <®_dldo1>; + device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ + /* TODO host wake line connected to PMIC GPIO pins */ + shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */ + max-speed = <1500000>; + }; +}; + &usbphy { usb1_vbus-supply = <®_vcc5v0>; status = "okay"; |