diff options
Diffstat (limited to 'Documentation')
3 files changed, 38 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index 27784b6edfed..fd2bed23e0e3 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -58,7 +58,11 @@ This binding for the SCU power domain providers uses the generic power domain binding[2]. Required properties: -- compatible: Should be "fsl,imx8qxp-scu-pd". +- compatible: Should be one of: + "fsl,imx8qm-scu-pd", + "fsl,imx8qxp-scu-pd" + followed by "fsl,scu-pd" + - #power-domain-cells: Must be 1. Contains the Resource ID used by SCU commands. See detailed Resource ID list from: @@ -154,7 +158,7 @@ firmware { }; pd: imx8qx-pd { - compatible = "fsl,imx8qxp-scu-pd"; + compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd"; #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt index 683eaf3aed79..dda7d6d66479 100644 --- a/Documentation/devicetree/bindings/bus/imx-weim.txt +++ b/Documentation/devicetree/bindings/bus/imx-weim.txt @@ -47,9 +47,9 @@ Optional properties: Timing property for child nodes. It is mandatory, not optional. - fsl,weim-cs-timing: The timing array, contains timing values for the - child node. We can get the CS index from the child - node's "reg" property. The number of registers depends - on the selected chip. + child node. We get the CS indexes from the address + ranges in the child node's "reg" property. + The number of registers depends on the selected chip: For i.MX1, i.MX21 ("fsl,imx1-weim") there are two registers: CSxU, CSxL. For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim") @@ -80,3 +80,29 @@ Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM: 0x0000c000 0x1404a38e 0x00000000>; }; }; + +Example for an imx6q-based board, a multi-chipselect device connected to WEIM: + +In this case, both chip select 0 and 1 will be configured with the same timing +array values. + + weim: weim@21b8000 { + compatible = "fsl,imx6q-weim"; + reg = <0x021b8000 0x4000>; + clocks = <&clks 196>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x02000000 + 1 0 0x0a000000 0x02000000 + 2 0 0x0c000000 0x02000000 + 3 0 0x0e000000 0x02000000>; + fsl,weim-cs-gpr = <&gpr>; + + acme@0 { + compatible = "acme,whatever"; + reg = <0 0 0x100>, <0 0x400000 0x800>, + <1 0x400000 0x800>; + fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100 + 0x00000000 0xa0000240 0x00000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt index 7c947a996df1..7c7e972aaa42 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt @@ -32,6 +32,9 @@ Required properties: Optional properties: - power-supply: Power supply used to power the domain +- clocks: a number of phandles to clocks that need to be enabled during + domain power-up sequencing to ensure reset propagation into devices + located inside this power domain Example: |