diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 293 insertions, 39 deletions
diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index dc9dc8c87f15..20c2ff2ba07e 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -1,35 +1,197 @@ -AM33XX MUSB GLUE - - compatible : Should be "ti,musb-am33xx" - - reg : offset and length of register sets, first usbss, then for musb instances - - interrupts : usbss, musb instance interrupts in order - - ti,hwmods : must be "usb_otg_hs" - - multipoint : Should be "1" indicating the musb controller supports - multipoint. This is a MUSB configuration-specific setting. - - num-eps : Specifies the number of endpoints. This is also a - MUSB configuration-specific setting. Should be set to "16" - - ram-bits : Specifies the ram address size. Should be set to "12" - - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" - represents PERIPHERAL. - - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" - represents PERIPHERAL. - - power : Should be "250". This signifies the controller can supply up to - 500mA when operating in host mode. + AM33xx MUSB +~~~~~~~~~~~~~~~ +- compatible: ti,am33xx-usb +- reg: offset and length of the usbss register sets +- ti,hwmods : must be "usb_otg_hs" + +The glue layer contains multiple child nodes. It is required the have +at least a control module node, USB node and a PHY node. The second USB +node and its PHY node is optional. The DMA node is also optional. + +Reset module +~~~~~~~~~~~~ +- compatible: ti,am335x-usb-ctrl-module +- reg: offset and length of the "USB control registers" in the "Control + Module" block. A second offset and length for the USB wake up control + in the same memory block. +- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for + the USB wake up control register. + +USB PHY +~~~~~~~ +compatible: ti,am335x-usb-phy +reg: offset and length of the "USB PHY" register space +ti,ctrl_mod: reference to the "reset module" node +reg-names: phy +The PHY should have a "phy" alias numbered properly in the alias +node. + +USB +~~~ +- compatible: ti,musb-am33xx +- reg: offset and length of "USB Controller Registers", and offset and + length of "USB Core" register space. +- reg-names: control for the ""USB Controller Registers" and "mc" for + "USB Core" register space +- interrupts: USB interrupt number +- interrupt-names: mc +- dr_mode: Should be one of "host", "peripheral" or "otg". +- mentor,multipoint: Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. +- mentor,num-eps: Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" +- mentor,ram-bits: Specifies the ram address size. Should be set to "12" +- mentor,power: Should be "500". This signifies the controller can supply up to + 500mA when operating in host mode. +- phys: reference to the USB phy +- dmas: specifies the dma channels +- dma-names: specifies the names of the channels. Use "rxN" for receive + and "txN" for transmit endpoints. N specifies the endpoint number. + +The controller should have an "usb" alias numbered properly in the alias +node. + +DMA +~~~ +- compatible: ti,am3359-cppi41 +- reg: offset and length of the following register spaces: USBSS, USB + CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager +- reg-names: glue, controller, scheduler, queuemgr +- #dma-cells: should be set to 2. The first number represents the + endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29 + for endpoints 1 … 15 on instance 1). The second number is 0 for RX and + 1 for TX transfers. +- #dma-channels: should be set to 30 representing the 15 endpoints for + each USB instance. Example: +~~~~~~~~ +The following example contains all the nodes as used on am335x-evm: + +aliases { + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; +}; -usb@47400000 { - compatible = "ti,musb-am33xx"; - reg = <0x47400000 0x1000 /* usbss */ - 0x47401000 0x800 /* musb instance 0 */ - 0x47401800 0x800>; /* musb instance 1 */ - interrupts = <17 /* usbss */ - 18 /* musb instance 0 */ - 19>; /* musb instance 1 */ - multipoint = <1>; - num-eps = <16>; - ram-bits = <12>; - port0-mode = <3>; - port1-mode = <3>; - power = <250>; +usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "usb_otg_hs"; + + ctrl_mod: control@44e10000 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x44e10620 0x10 + 0x44e10648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1_phy: usb-phy@47401b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "host" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@07402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7a95c651ceb3..e807635f9e1c 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -3,10 +3,12 @@ synopsys DWC3 CORE DWC3- USB3 CONTROLLER Required properties: - - compatible: must be "synopsys,dwc3" + - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. - - usb-phy : array of phandle for the PHY device + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY Optional properties: - tx-fifo-resize: determines if the FIFO *has* to be reallocated. @@ -14,7 +16,7 @@ Optional properties: This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt new file mode 100644 index 000000000000..477d5bb5e51c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -0,0 +1,24 @@ +Generic USB Properties + +Optional properties: + - maximum-speed: tells USB controllers we want to work up to a certain + speed. Valid arguments are "super-speed", "high-speed", + "full-speed" and "low-speed". In case this isn't passed + via DT, USB controllers should default to their maximum + HW capability. + - dr_mode: tells Dual-Role USB controllers that we want to work on a + particular mode. Valid arguments are "host", + "peripheral" and "otg". In case this attribute isn't + passed via DT, USB DRD controllers should default to + OTG. + +This is an attribute to a USB controller such as: + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + maximum-speed = "super-speed"; + dr_mode = "otg"; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index c4c9e9e664aa..ba797d3e6326 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -3,7 +3,7 @@ Tegra SOC USB PHY The device node for Tegra SOC USB PHY: Required properties : - - compatible : Should be "nvidia,tegra20-usb-phy". + - compatible : Should be "nvidia,tegra<chip>-usb-phy". - reg : Defines the following set of registers, in the order listed: - The PHY's own register set. Always present. @@ -24,17 +24,26 @@ Required properties : Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. -Required PHY timing params for utmi phy: +Required PHY timing params for utmi phy, for all chips: - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before start of sync launches RxActive - nvidia,elastic-limit : Variable FIFO Depth of elastic input store - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait before declare IDLE. - nvidia,term-range-adj : Range adjusment on terminations - - nvidia,xcvr-setup : HS driver output control + - Either one of the following for HS driver output control: + - nvidia,xcvr-setup : integer, uses the provided value. + - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read + from the on-chip fuses + If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. - nvidia,xcvr-lsfslew : LS falling slew rate control. - nvidia,xcvr-lsrslew : LS rising slew rate control. +Required PHY timing params for utmi phy, only on Tegra30 and above: + - nvidia,xcvr-hsslew : HS slew rate control. + - nvidia,hssquelch-level : HS squelch detector level. + - nvidia,hsdiscon-level : HS disconnect detector level. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some @@ -48,5 +57,5 @@ Optional properties: peripheral means it is device controller otg means it can operate as either ("on the go") -Required properties for dr_mode == otg: +VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt new file mode 100644 index 000000000000..b83d428a265e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt @@ -0,0 +1,40 @@ +Samsung High Speed USB OTG controller +----------------------------- + +The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards. +It gives functionality of OTG-compliant USB 2.0 host and device with +support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps) +operation. + +Currently only device mode is supported. + +Binding details +----- + +Required properties: +- compatible: "samsung,s3c6400-hsotg" should be used for all currently + supported SoC, +- interrupt-parent: phandle for the interrupt controller to which the + interrupt signal of the HSOTG block is routed, +- interrupts: specifier of interrupt signal of interrupt controller, + according to bindings of interrupt controller, +- clocks: contains an array of clock specifiers: + - first entry: OTG clock +- clock-names: contains array of clock names: + - first entry: must be "otg" +- vusb_d-supply: phandle to voltage regulator of digital section, +- vusb_a-supply: phandle to voltage regulator of analog section. + +Example +----- + + hsotg@12480000 { + compatible = "samsung,s3c6400-hsotg"; + reg = <0x12480000 0x20000>; + interrupts = <0 71 0>; + clocks = <&clock 305>; + clock-names = "otg"; + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + }; + diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt new file mode 100644 index 000000000000..5752df0e17a2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -0,0 +1,14 @@ +USB xHCI controllers + +Required properties: + - compatible: should be "xhci-platform". + - reg: should contain address and length of the standard XHCI + register set for the device. + - interrupts: one XHCI interrupt should be described here. + +Example: + usb@f0931000 { + compatible = "xhci-platform"; + reg = <0xf0931000 0x8c8>; + interrupts = <0x0 0x4e 0x0>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 8c5be48b43c8..a018da4a7ad7 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -1,8 +1,11 @@ SMSC USB3503 High-Speed Hub Controller Required properties: -- compatible: Should be "smsc,usb3503". -- reg: Specifies the i2c slave address, it should be 0x08. +- compatible: Should be "smsc,usb3503" or "smsc,usb3503a". + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x08 + if I2C is used. - connect-gpios: Should specify GPIO for connect. - disabled-ports: Should specify the ports unused. '1' or '2' or '3' are availe for this property to describe the port |