diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 21 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 52d37fd8d3e5..ce4311d726ae 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -7,6 +7,7 @@ Required properties: - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC - reg : Should contain I2C/HS-I2C registers location and length - interrupts : Should contain I2C/HS-I2C interrupt +- clocks : Should contain the I2C/HS-I2C clock specifier Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index 33df3932168e..8db32384a486 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -27,6 +27,8 @@ property is used. - amd,serdes-cdr-rate: CDR rate speed selection - amd,serdes-pq-skew: PQ (data sampling) skew - amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable Example: xgbe_phy@e1240800 { @@ -41,4 +43,6 @@ Example: amd,serdes-cdr-rate = <2>, <2>, <7>; amd,serdes-pq-skew = <10>, <10>, <30>; amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index 7f76214f728a..289c40ed7470 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -21,6 +21,18 @@ Optional properties: - reg-io-width : the size (in bytes) of the IO accesses that should be performed on the device. If this property is not present then single byte accesses are used. +- dcd-override : Override the DCD modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- dsr-override : Override the DTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- cts-override : Override the CTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- ri-override : Override the RI modem status signal. This signal will always be + reported as inactive instead of being obtained from the modem status register. + Define this if your serial port does not use this pin. Example: @@ -31,6 +43,10 @@ Example: interrupts = <10>; reg-shift = <2>; reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; }; Example with one clock: |