diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
12 files changed, 216 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 24b656014089..1d4afe9644b6 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -1,4 +1,4 @@ -Common leds properties. +* Common leds properties. LED and flash LED devices provide the same basic functionality as current regulators, but extended with LED and flash LED specific features like @@ -49,6 +49,22 @@ Optional properties for child nodes: - panic-indicator : This property specifies that the LED should be used, if at all possible, as a panic indicator. +- trigger-sources : List of devices which should be used as a source triggering + this LED activity. Some LEDs can be related to a specific + device and should somehow indicate its state. E.g. USB 2.0 + LED may react to device(s) in a USB 2.0 port(s). + Another common example is switch or router with multiple + Ethernet ports each of them having its own LED assigned + (assuming they are not hardwired). In such cases this + property should contain phandle(s) of related source + device(s). + In many cases LED can be related to more than one device + (e.g. one USB LED vs. multiple USB ports). Each source + should be represented by a node in the device tree and be + referenced by a phandle and a set of phandle arguments. A + length of arguments should be specified by the + #trigger-source-cells property in the source node. + Required properties for flash LED child nodes: - flash-max-microamp : Maximum flash LED supply current in microamperes. - flash-max-timeout-us : Maximum timeout in microseconds after which the flash @@ -59,7 +75,17 @@ property can be omitted. For controllers that have no configurable timeout the flash-max-timeout-us property can be omitted. -Examples: +* Trigger source providers + +Each trigger source should be represented by a device tree node. It may be e.g. +a USB port or an Ethernet device. + +Required properties for trigger source: +- #trigger-source-cells : Number of cells in a source trigger. Typically 0 for + nodes of simple trigger sources (e.g. a specific USB + port). + +* Examples gpio-leds { compatible = "gpio-leds"; @@ -69,6 +95,11 @@ gpio-leds { linux,default-trigger = "heartbeat"; gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; }; + + usb { + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + trigger-sources = <&ohci_port1>, <&ehci_port1>; + }; }; max77693-led { diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt index 09aeba94538d..32f057260351 100644 --- a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt @@ -3,9 +3,10 @@ Driver for Broadcom Northstar USB 3.0 PHY Required properties: - compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy". -- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B - MMI. -- reg-names: "dmp" and "ccb-mii" +- reg: address of MDIO bus device +- usb3-dmp-syscon: phandle to syscon with DMP (Device Management Plugin) + registers +- #phy-cells: must be 0 Initialization of USB 3.0 PHY depends on Northstar version. There are currently three known series: Ax, Bx and Cx. @@ -15,9 +16,19 @@ Known B1: BCM4707 rev 6 Known C0: BCM47094 rev 0 Example: - usb3-phy { - compatible = "brcm,ns-ax-usb3-phy"; - reg = <0x18105000 0x1000>, <0x18003000 0x1000>; - reg-names = "dmp", "ccb-mii"; - #phy-cells = <0>; + mdio: mdio@0 { + reg = <0x0>; + #size-cells = <1>; + #address-cells = <0>; + + usb3-phy@10 { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x10>; + usb3-dmp-syscon = <&usb3_dmp>; + #phy-cells = <0>; + }; + }; + + usb3_dmp: syscon@18105000 { + reg = <0x18105000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt new file mode 100644 index 000000000000..04f063aa7883 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt @@ -0,0 +1,30 @@ +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY + +Required properties: + - compatible: brcm,ns2-drd-phy + - reg: offset and length of the NS2 PHY related registers. + - reg-names + The below registers must be provided. + icfg - for DRD ICFG configurations + rst-ctrl - for DRD IDM reset + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset + usb2-strap - for port over current polarity reversal + - #phy-cells: Must be 0. No args required. + - vbus-gpios: vbus gpio binding + - id-gpios: id gpio binding + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbdrd_phy: phy@66000960 { + #phy-cells = <0>; + compatible = "brcm,ns2-drd-phy"; + reg = <0x66000960 0x24>, + <0x67012800 0x4>, + <0x6501d148 0x4>, + <0x664d0700 0x4>; + reg-names = "icfg", "rst-ctrl", + "crmu-ctrl", "usb2-strap"; + id-gpios = <&gpio_g 30 0>; + vbus-gpios = <&gpio_g 31 0>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 6ccce09d8bbf..97977cd29a98 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -7,12 +7,13 @@ Required properties: "brcm,iproc-ns2-sata-phy" "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" + "brcm,iproc-sr-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - reg: register ranges for the PHY PCB interface - reg-names: should be "phy" and "phy-ctrl" The "phy-ctrl" registers are only required for - "brcm,iproc-ns2-sata-phy". + "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy". Sub-nodes: Each port's PHY should be represented as a sub-node. @@ -23,8 +24,8 @@ Sub-nodes required properties: Sub-nodes optional properties: - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port - This property is not applicable for "brcm,iproc-ns2-sata-phy" and - "brcm,iproc-nsp-sata-phy". + This property is not applicable for "brcm,iproc-ns2-sata-phy", + "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy". Example: sata-phy@f0458100 { diff --git a/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt new file mode 100644 index 000000000000..a105494a0fc9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt @@ -0,0 +1,17 @@ +* Amlogic Meson GXL and GXM USB2 PHY binding + +Required properties: +- compatible: Should be "amlogic,meson-gxl-usb2-phy" +- reg: The base address and length of the registers +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) + +Optional properties: +- phy-supply: see phy-bindings.txt in this directory + + +Example: + usb2_phy0: phy@78000 { + compatible = "amlogic,meson-gxl-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0x78000 0x0 0x20>; + }; diff --git a/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt index 5fa73b9d20f5..d81d73aea608 100644 --- a/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt @@ -1,7 +1,8 @@ -* Amlogic Meson8b and GXBB USB2 PHY +* Amlogic Meson8, Meson8b and GXBB USB2 PHY Required properties: - compatible: Depending on the platform this should be one of: + "amlogic,meson8-usb2-phy" "amlogic,meson8b-usb2-phy" "amlogic,meson-gxbb-usb2-phy" - reg: The base address and length of the registers diff --git a/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt new file mode 100644 index 000000000000..2eb9b2b69037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt @@ -0,0 +1,40 @@ +Motorola CPCAP PMIC USB PHY binding + +Required properties: +compatible: Shall be either "motorola,cpcap-usb-phy" or + "motorola,mapphone-cpcap-usb-phy" +#phy-cells: Shall be 0 +interrupts: CPCAP PMIC interrupts used by the USB PHY +interrupt-names: Interrupt names +io-channels: IIO ADC channels used by the USB PHY +io-channel-names: IIO ADC channel names +vusb-supply: Regulator for the PHY + +Optional properties: +pinctrl: Optional alternate pin modes for the PHY +pinctrl-names: Names for optional pin modes +mode-gpios: Optional GPIOs for configuring alternate modes + +Example: +cpcap_usb2_phy: phy { + compatible = "motorola,mapphone-cpcap-usb-phy"; + pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>; + pinctrl-1 = <&usb_ulpi_pins>; + pinctrl-2 = <&usb_utmi_pins>; + pinctrl-3 = <&uart3_pins>; + pinctrl-names = "default", "ulpi", "utmi", "uart"; + #phy-cells = <0>; + interrupts-extended = < + &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0 + &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0 + &cpcap 48 1 + >; + interrupt-names = + "id_ground", "id_float", "se0conn", "vbusvld", + "sessvld", "sessend", "se1", "dm", "dp"; + mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH + &gpio1 0 GPIO_ACTIVE_HIGH>; + io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>; + io-channel-names = "vbus", "id"; + vusb-supply = <&vusb>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index e71a8d23f4a8..84d59b0db8df 100644 --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -2,6 +2,7 @@ ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK Required properties (phy (parent) node): - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-usb2phy" * "rockchip,rk3328-usb2phy" * "rockchip,rk3366-usb2phy" * "rockchip,rk3399-usb2phy" diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt new file mode 100644 index 000000000000..f94cea48f6b1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -0,0 +1,46 @@ +* Renesas R-Car generation 3 USB 3.0 PHY + +This file provides information on what the device node for the R-Car generation +3 USB 3.0 PHY contains. +If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL +instead of USB3_CLK. However, if you don't want to these features, you don't +need this driver. + +Required properties: +- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 + SoC. + "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 + SoC. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible + device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 3.0 PHY register block. +- clocks: A list of phandles and clock-specifier pairs. +- clock-names: Name of the clocks. + - The funcional clock must be "usb3-if". + - The usb3's external clock must be "usb3s_clk". + - The usb2's external clock must be "usb_extal". If you want to use the ssc, + the clock-frequency must not be 0. +- #phy-cells: see phy-bindings.txt in the same directory, must be <0>. + +Optional properties: +- renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using + the following values as u32: + - 0 (or the property doesn't exist): disable the ssc + - 4980: enable the ssc as -4980 ppm + - 4492: enable the ssc as -4492 ppm + - 4003: enable the ssc as -4003 ppm + +Example (R-Car H3): + + usb-phy@e65ee000 { + compatible = "renesas,r8a7795-usb3-phy", + "renesas,rcar-gen3-usb3-phy"; + reg = <0 0xe65ee000 0 0x90>; + clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>; + clock-names = "usb3-if", "usb3s_clk", "usb_extal"; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index f658f394c2d3..52fb41046b34 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -45,6 +45,8 @@ Optional properties: a free-running PHY clock. - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power from P0 to P1/P2/P3 without delay. + - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check + during HS transmit. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold diff --git a/Documentation/devicetree/bindings/usb/iproc-udc.txt b/Documentation/devicetree/bindings/usb/iproc-udc.txt new file mode 100644 index 000000000000..272d7faf1a97 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/iproc-udc.txt @@ -0,0 +1,21 @@ +Broadcom IPROC USB Device controller. + +The device node is used for UDCs integrated into Broadcom's +iProc family (Northstar2, Cygnus) of SoCs'. The UDC is based +on Synopsys Designware Cores AHB Subsystem Device Controller +IP. + +Required properties: + - compatible: Add the compatibility strings for supported platforms. + For Broadcom NS2 platform, add "brcm,ns2-udc","brcm,iproc-udc". + For Broadcom Cygnus platform, add "brcm,cygnus-udc", "brcm,iproc-udc". + - reg: Offset and length of UDC register set + - interrupts: description of interrupt line + - phys: phandle to phy node. + +Example: + udc_dwc: usb@664e0000 { + compatible = "brcm,ns2-udc", "brcm,iproc-udc"; + reg = <0x664e0000 0x2000>; + interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd_phy>; diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 9df456968596..e8766b08c93b 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -10,6 +10,7 @@ Optional properties: - big-endian-desc : boolean, set this for hcds with big-endian descriptors - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc - no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA +- remote-wakeup-connected: remote wakeup is wired on the platform - num-ports : u32, to override the detected port count - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair |