diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video/samsung-fimd.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/video/samsung-fimd.txt | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt deleted file mode 100644 index a8bbbde03e79..000000000000 --- a/Documentation/devicetree/bindings/video/samsung-fimd.txt +++ /dev/null @@ -1,110 +0,0 @@ -Device-Tree bindings for Samsung SoC display controller (FIMD) - -FIMD (Fully Interactive Mobile Display) is the Display Controller for the -Samsung series of SoCs which transfers the image data from a video memory -buffer to an external LCD interface. - -Required properties: -- compatible: value should be one of the following - "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ - "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ - "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ - "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ - "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ - "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ - "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ - -- reg: physical base address and length of the FIMD registers set. - -- interrupt-parent: should be the phandle of the fimd controller's - parent interrupt controller. - -- interrupts: should contain a list of all FIMD IP block interrupts in the - order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier - format depends on the interrupt controller used. - -- interrupt-names: should contain the interrupt names: "fifo", "vsync", - "lcd_sys", in the same order as they were listed in the interrupts - property. - -- pinctrl-0: pin control group to be used for this controller. - -- pinctrl-names: must contain a "default" entry. - -- clocks: must include clock specifiers corresponding to entries in the - clock-names property. - -- clock-names: list of clock names sorted in the same order as the clocks - property. Must contain "sclk_fimd" and "fimd". - -Optional Properties: -- power-domains: a phandle to FIMD power domain node. -- samsung,invert-vden: video enable signal is inverted -- samsung,invert-vclk: video clock signal is inverted -- display-timings: timing settings for FIMD, as described in document [1]. - Can be used in case timings cannot be provided otherwise - or to override timings provided by the panel. -- samsung,sysreg: handle to syscon used to control the system registers -- i80-if-timings: timing configuration for lcd i80 interface support. - - cs-setup: clock cycles for the active period of address signal is enabled - until chip select is enabled. - If not specified, the default value(0) will be used. - - wr-setup: clock cycles for the active period of CS signal is enabled until - write signal is enabled. - If not specified, the default value(0) will be used. - - wr-active: clock cycles for the active period of CS is enabled. - If not specified, the default value(1) will be used. - - wr-hold: clock cycles for the active period of CS is disabled until write - signal is disabled. - If not specified, the default value(0) will be used. - - The parameters are defined as: - - VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|?? - : : : : : - Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX - | cs-setup+1 | : : : - |<---------->| : : : - Chip Select ???????????????|____________:____________:____________|?? - | wr-setup+1 | | wr-hold+1 | - |<---------->| |<---------->| - Write Enable ????????????????????????????|____________|??????????????? - | wr-active+1| - |<---------->| - Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>-- - -The device node can contain 'port' child nodes according to the bindings defined -in [2]. The following are properties specific to those nodes: -- reg: (required) port index, can be: - 0 - for CAMIF0 input, - 1 - for CAMIF1 input, - 2 - for CAMIF2 input, - 3 - for parallel output, - 4 - for write-back interface - -[1]: Documentation/devicetree/bindings/video/display-timing.txt -[2]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - -SoC specific DT entry: - - fimd@11c00000 { - compatible = "samsung,exynos4210-fimd"; - interrupt-parent = <&combiner>; - reg = <0x11c00000 0x20000>; - interrupt-names = "fifo", "vsync", "lcd_sys"; - interrupts = <11 0>, <11 1>, <11 2>; - clocks = <&clock 140>, <&clock 283>; - clock-names = "sclk_fimd", "fimd"; - power-domains = <&pd_lcd0>; - status = "disabled"; - }; - -Board specific DT entry: - - fimd@11c00000 { - pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; - pinctrl-names = "default"; - status = "okay"; - }; |