diff options
Diffstat (limited to 'Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt | 62 |
1 files changed, 57 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt index b6c0ae53d4dc..f02f38527a6b 100644 --- a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt @@ -52,13 +52,47 @@ Required properties : Must set as following values: TEGRA_SOCTHERM_THROT_LEVEL_LOW, TEGRA_SOCTHERM_THROT_LEVEL_MED TEGRA_SOCTHERM_THROT_LEVEL_HIGH, TEGRA_SOCTHERM_THROT_LEVEL_NONE + - nvidia,gpu-throt-level: This property is for Tegra124 and Tegra210. + It is the level of pulse skippers, which used to throttle clock + frequencies. It indicates gpu clock throttling depth and can be + programmed to any of the following values which represent a throttling + percentage: + TEGRA_SOCTHERM_THROT_LEVEL_NONE (0%) + TEGRA_SOCTHERM_THROT_LEVEL_LOW (50%), + TEGRA_SOCTHERM_THROT_LEVEL_MED (75%), + TEGRA_SOCTHERM_THROT_LEVEL_HIGH (85%). - #cooling-cells: Should be 1. This cooling device only support on/off state. See ./thermal.txt for a description of this property. + Optional properties: The following properties are T210 specific and + valid only for OCx throttle events. + - nvidia,count-threshold: Specifies the number of OC events that are + required for triggering an interrupt. Interrupts are not triggered if + the property is missing. A value of 0 will interrupt on every OC alarm. + - nvidia,polarity-active-low: Configures the polarity of the OC alaram + signal. If present, this means assert low, otherwise assert high. + - nvidia,alarm-filter: Number of clocks to filter event. When the filter + expires (which means the OC event has not occurred for a long time), + the counter is cleared and filter is rearmed. Default value is 0. + - nvidia,throttle-period-us: Specifies the number of uSec for which + throttling is engaged after the OC event is deasserted. Default value + is 0. + +Optional properties: +- nvidia,thermtrips : When present, this property specifies the temperature at + which the soctherm hardware will assert the thermal trigger signal to the + Power Management IC, which can be configured to reset or shutdown the device. + It is an array of pairs where each pair represents a tsensor id followed by a + temperature in milli Celcius. In the absence of this property the critical + trip point will be used for thermtrip temperature. + Note: -- the "critical" type trip points will be set to SOC_THERM hardware as the -shut down temperature. Once the temperature of this thermal zone is higher -than it, the system will be shutdown or reset by hardware. +- the "critical" type trip points will be used to set the temperature at which +the SOC_THERM hardware will assert a thermal trigger if the "nvidia,thermtrips" +property is missing. When the thermtrips property is present, the breach of a +critical trip point is reported back to the thermal framework to implement +software shutdown. + - the "hot" type trip points will be set to SOC_THERM hardware as the throttle temperature. Once the the temperature of this thermal zone is higher than it, it will trigger the HW throttle event. @@ -79,25 +113,32 @@ Example : #thermal-sensor-cells = <1>; + nvidia,thermtrips = <TEGRA124_SOCTHERM_SENSOR_CPU 102500 + TEGRA124_SOCTHERM_SENSOR_GPU 103000>; + throttle-cfgs { /* * When the "heavy" cooling device triggered, - * the HW will skip cpu clock's pulse in 85% depth + * the HW will skip cpu clock's pulse in 85% depth, + * skip gpu clock's pulse in 85% level */ throttle_heavy: heavy { nvidia,priority = <100>; nvidia,cpu-throt-percent = <85>; + nvidia,gpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_HIGH>; #cooling-cells = <1>; }; /* * When the "light" cooling device triggered, - * the HW will skip cpu clock's pulse in 50% depth + * the HW will skip cpu clock's pulse in 50% depth, + * skip gpu clock's pulse in 50% level */ throttle_light: light { nvidia,priority = <80>; nvidia,cpu-throt-percent = <50>; + nvidia,gpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_LOW>; #cooling-cells = <1>; }; @@ -107,6 +148,17 @@ Example : * arbiter will select the highest priority as the final throttle * settings to skip cpu pulse. */ + + throttle_oc1: oc1 { + nvidia,priority = <50>; + nvidia,polarity-active-low; + nvidia,count-threshold = <100>; + nvidia,alarm-filter = <5100000>; + nvidia,throttle-period-us = <0>; + nvidia,cpu-throt-percent = <75>; + nvidia,gpu-throt-level = + <TEGRA_SOCTHERM_THROT_LEVEL_MED>; + }; }; }; |