diff options
Diffstat (limited to 'Documentation/devicetree/bindings/serial')
16 files changed, 376 insertions, 145 deletions
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index aeb6db4e35c3..3cba12f855b7 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -21,6 +21,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "intel,xscale-uart" - "ti,da830-uart" - "aspeed,ast2400-vuart" - "aspeed,ast2500-vuart" @@ -51,6 +52,7 @@ Optional properties: - tx-threshold: Specify the TX FIFO low water indication for parts with programmable TX FIFO thresholds. - resets : phandle + reset specifier pairs +- overrun-throttle-ms : how long to pause uart rx when input overrun is encountered. Note: * fsl,ns16550: diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index 6bd3f2e93d61..21483ba820bc 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -8,6 +8,8 @@ Required properties: on LS1021A SoC with 32-bit big-endian register organization - "fsl,imx7ulp-lpuart" for lpuart compatible with the one integrated on i.MX7ULP SoC with 32-bit little-endian register organization + - "fsl,imx8qxp-lpuart" for lpuart compatible with the one integrated + on i.MX8QXP SoC with 32-bit little-endian register organization - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.txt b/Documentation/devicetree/bindings/serial/ingenic,uart.txt index c3c6406d5cfe..24ed8769f4af 100644 --- a/Documentation/devicetree/bindings/serial/ingenic,uart.txt +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.txt @@ -6,7 +6,8 @@ Required properties: - "ingenic,jz4760-uart", - "ingenic,jz4770-uart", - "ingenic,jz4775-uart", - - "ingenic,jz4780-uart". + - "ingenic,jz4780-uart", + - "ingenic,x1000-uart". - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. - clocks : phandles to the module & baud clocks. diff --git a/Documentation/devicetree/bindings/serial/lantiq_asc.txt b/Documentation/devicetree/bindings/serial/lantiq_asc.txt index 3acbd309ab9d..40e81a5818f6 100644 --- a/Documentation/devicetree/bindings/serial/lantiq_asc.txt +++ b/Documentation/devicetree/bindings/serial/lantiq_asc.txt @@ -6,8 +6,23 @@ Required properties: - interrupts: the 3 (tx rx err) interrupt numbers. The interrupt specifier depends on the interrupt-parent interrupt controller. +Optional properties: +- clocks: Should contain frequency clock and gate clock +- clock-names: Should be "freq" and "asc" + Example: +asc0: serial@16600000 { + compatible = "lantiq,asc"; + reg = <0x16600000 0x100000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cgu CLK_SSX4>, <&cgu GCLK_UART>; + clock-names = "freq", "asc"; +}; + asc1: serial@e100c00 { compatible = "lantiq,asc"; reg = <0xE100C00 0x400>; diff --git a/Documentation/devicetree/bindings/serial/milbeaut-uart.txt b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt new file mode 100644 index 000000000000..3d2fb1a7ba94 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt @@ -0,0 +1,21 @@ +Socionext Milbeaut UART controller + +Required properties: +- compatible: should be "socionext,milbeaut-usio-uart". +- reg: offset and length of the register set for the device. +- interrupts: two interrupts specifier. +- interrupt-names: should be "rx", "tx". +- clocks: phandle to the input clock. + +Optional properties: +- auto-flow-control: flow control enable. + +Example: + usio1: usio_uart@1e700010 { + compatible = "socionext,milbeaut-usio-uart"; + reg = <0x1e700010 0x10>; + interrupts = <0 141 0x4>, <0 149 0x4>; + interrupt-names = "rx", "tx"; + clocks = <&clk 2>; + auto-flow-control; + }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 742cb470595b..bcfb13194f16 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -16,6 +16,7 @@ Required properties: * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS + * "mediatek,mt8183-uart", "mediatek,mt6577-uart" for MT8183 compatible UARTS * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt new file mode 100644 index 000000000000..085a8591accd --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt @@ -0,0 +1,35 @@ +NVIDIA Tegra Combined UART (TCU) + +The TCU is a system for sharing a hardware UART instance among multiple +systems within the Tegra SoC. It is implemented through a mailbox- +based protocol where each "virtual UART" has a pair of mailboxes, one +for transmitting and one for receiving, that is used to communicate +with the hardware implementing the TCU. + +Required properties: +- name : Should be tcu +- compatible + Array of strings + One of: + - "nvidia,tegra194-tcu" +- mbox-names: + "rx" - Mailbox for receiving data from hardware UART + "tx" - Mailbox for transmitting data to hardware UART +- mboxes: Mailboxes corresponding to the mbox-names. + +This node is a mailbox consumer. See the following files for details of +the mailbox subsystem, and the specifiers implemented by the relevant +provider(s): + +- .../mailbox/mailbox.txt +- .../mailbox/nvidia,tegra186-hsp.txt + +Example bindings: +----------------- + +tcu: tcu { + compatible = "nvidia,tegra194-tcu"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM 0>, + <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM 1>; + mbox-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index c35d5ece1156..0a9b5444f4e6 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -22,6 +22,8 @@ Optional properties: - dma-names : "rx" for receive channel, "tx" for transmit channel. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt - rs485-rts-active-high: drive RTS high when sending (default is low). +- clocks: phandle to the functional clock as per + Documentation/devicetree/bindings/clock/clock-bindings.txt Example: diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt deleted file mode 100644 index 77863aefe9ef..000000000000 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ /dev/null @@ -1,51 +0,0 @@ -* ARM AMBA Primecell PL011 serial UART - -Required properties: -- compatible: must be "arm,primecell", "arm,pl011", "zte,zx296702-uart" -- reg: exactly one register range with length 0x1000 -- interrupts: exactly one interrupt specifier - -Optional properties: -- pinctrl: - When present, must have one state named "default", - and may contain a second name named "sleep". The former - state sets up pins for ordinary operation whereas - the latter state will put the associated pins to sleep - when the UART is unused -- clocks: - When present, the first clock listed must correspond to - the clock named UARTCLK on the IP block, i.e. the clock - to the external serial line, whereas the second clock - must correspond to the PCLK clocking the internal logic - of the block. Just listing one clock (the first one) is - deprecated. -- clock-names: - When present, the first clock listed must be named - "uartclk" and the second clock listed must be named - "apb_pclk" -- dmas: - When present, may have one or two dma channels. - The first one must be named "rx", the second one - must be named "tx". -- auto-poll: - Enables polling when using RX DMA. -- poll-rate-ms: - Rate at which poll occurs when auto-poll is set, - default 100ms. -- poll-timeout-ms: - Poll timeout when auto-poll is set, default - 3000ms. - -See also bindings/arm/primecell.txt - -Example: - -uart@80120000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x80120000 0x1000>; - interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; - dma-names = "rx", "tx"; - clocks = <&foo_clk>, <&bar_clk>; - clock-names = "uartclk", "apb_pclk"; -}; diff --git a/Documentation/devicetree/bindings/serial/pl011.yaml b/Documentation/devicetree/bindings/serial/pl011.yaml new file mode 100644 index 000000000000..1a64d59152aa --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/pl011.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM AMBA Primecell PL011 serial UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +# Need a custom select here or 'arm,primecell' will match on lots of nodes +select: + properties: + compatible: + contains: + enum: + - arm,pl011 + - zte,zx296702-uart + required: + - compatible + +properties: + compatible: + oneOf: + - items: + - const: arm,pl011 + - const: arm,primecell + - items: + - const: zte,zx296702-uart + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + description: + When present, must have one state named "default", + and may contain a second name named "sleep". The former + state sets up pins for ordinary operation whereas + the latter state will put the associated pins to sleep + when the UART is unused + minItems: 1 + items: + - const: default + - const: sleep + + clocks: + description: + When present, the first clock listed must correspond to + the clock named UARTCLK on the IP block, i.e. the clock + to the external serial line, whereas the second clock + must correspond to the PCLK clocking the internal logic + of the block. Just listing one clock (the first one) is + deprecated. + maxItems: 2 + + clock-names: + items: + - const: uartclk + - const: apb_pclk + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: tx + + auto-poll: + description: + Enables polling when using RX DMA. + type: boolean + + poll-rate-ms: + description: + Rate at which poll occurs when auto-poll is set. + default 100ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 100 + + poll-timeout-ms: + description: + Poll timeout when auto-poll is set, default + 3000ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 3000 + +required: + - compatible + - reg + - interrupts + +dependencies: + poll-rate-ms: [ auto-poll ] + poll-timeout-ms: [ auto-poll ] + +additionalProperties: false + +examples: + - | + serial@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 4>; + dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&foo_clk>, <&bar_clk>; + clock-names = "uartclk", "apb_pclk"; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt new file mode 100644 index 000000000000..a08df97a69e6 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt @@ -0,0 +1,17 @@ +RDA Micro UART + +Required properties: +- compatible : "rda,8810pl-uart" for RDA8810PL SoCs. +- reg : Offset and length of the register set for the device. +- interrupts : Should contain UART interrupt. +- clocks : Phandle to the input clock. + + +Example: + + uart2: serial@20a90000 { + compatible = "rda,8810pl-uart"; + reg = <0x20a90000 0x1000>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_clk>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt b/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt deleted file mode 100644 index 8b9e0d4dc2e4..000000000000 --- a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt +++ /dev/null @@ -1,10 +0,0 @@ -Renesas RZ/N1 UART - -This controller is based on the Synopsys DesignWare ABP UART and inherits all -properties defined in snps-dw-apb-uart.txt except for the compatible property. - -Required properties: -- compatible : The device specific string followed by the generic RZ/N1 string. - Therefore it must be one of: - "renesas,r9a06g032-uart", "renesas,rzn1-uart" - "renesas,r9a06g033-uart", "renesas,rzn1-uart" diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index e52e16c6bc57..dd63151dc8b6 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -24,8 +24,14 @@ Required properties: - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. - "renesas,scif-r8a77470" for R8A77470 (RZ/G1C) SCIF compatible UART. - "renesas,hscif-r8a77470" for R8A77470 (RZ/G1C) HSCIF compatible UART. + - "renesas,scif-r8a774a1" for R8A774A1 (RZ/G2M) SCIF compatible UART. + - "renesas,hscif-r8a774a1" for R8A774A1 (RZ/G2M) HSCIF compatible UART. + - "renesas,scif-r8a774c0" for R8A774C0 (RZ/G2E) SCIF compatible UART. + - "renesas,hscif-r8a774c0" for R8A774C0 (RZ/G2E) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. + - "renesas,hscif-r8a7778" for R8A7778 (R-Car M1) HSCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. + - "renesas,hscif-r8a7779" for R8A7779 (R-Car H1) HSCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. @@ -61,13 +67,13 @@ Required properties: - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, - - "renesas,rcar-gen2-scif" for R-Car Gen2 SCIF compatible UART, - - "renesas,rcar-gen3-scif" for R-Car Gen3 SCIF compatible UART, - - "renesas,rcar-gen2-scifa" for R-Car Gen2 SCIFA compatible UART, - - "renesas,rcar-gen2-scifb" for R-Car Gen2 SCIFB compatible UART, + - "renesas,rcar-gen2-scif" for R-Car Gen2 and RZ/G1 SCIF compatible UART, + - "renesas,rcar-gen3-scif" for R-Car Gen3 and RZ/G2 SCIF compatible UART, + - "renesas,rcar-gen2-scifa" for R-Car Gen2 and RZ/G1 SCIFA compatible UART, + - "renesas,rcar-gen2-scifb" for R-Car Gen2 and RZ/G1 SCIFB compatible UART, - "renesas,rcar-gen1-hscif" for R-Car Gen1 HSCIF compatible UART, - - "renesas,rcar-gen2-hscif" for R-Car Gen2 HSCIF compatible UART, - - "renesas,rcar-gen3-hscif" for R-Car Gen3 HSCIF compatible UART, + - "renesas,rcar-gen2-hscif" for R-Car Gen2 and RZ/G1 HSCIF compatible UART, + - "renesas,rcar-gen3-hscif" for R-Car Gen3 and RZ/G2 HSCIF compatible UART, - "renesas,scif" for generic SCIF compatible UART. - "renesas,scifa" for generic SCIFA compatible UART. - "renesas,scifb" for generic SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt index b7c29f74ebb2..b92592dff6dd 100644 --- a/Documentation/devicetree/bindings/serial/rs485.txt +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -16,7 +16,7 @@ Optional properties: - linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 feature at boot time. It can be disabled later with proper ioctl. - rs485-rx-during-tx: empty property that enables the receiving of data even - whilst sending data. + while sending data. RS485 example for Atmel USART: usart0: serial@fff8c000 { diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt deleted file mode 100644 index 12bbe9f22560..000000000000 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ /dev/null @@ -1,76 +0,0 @@ -* Synopsys DesignWare ABP UART - -Required properties: -- compatible : "snps,dw-apb-uart" -- reg : offset and length of the register set for the device. -- interrupts : should contain uart interrupt. - -Clock handling: -The clock rate of the input clock needs to be supplied by one of -- clock-frequency : the input clock frequency for the UART. -- clocks : phandle to the input clock - -The supplying peripheral clock can also be handled, needing a second property -- clock-names: tuple listing input clock names. - Required elements: "baudclk", "apb_pclk" - -Optional properties: -- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE - configuration parameter. Define this if your UART does not implement the busy - functionality. -- resets : phandle to the parent reset controller. -- reg-shift : quantity to shift the register offsets by. If this property is - not present then the register offsets are not shifted. -- reg-io-width : the size (in bytes) of the IO accesses that should be - performed on the device. If this property is not present then single byte - accesses are used. -- dcd-override : Override the DCD modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- dsr-override : Override the DTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- cts-override : Override the CTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- ri-override : Override the RI modem status signal. This signal will always be - reported as inactive instead of being obtained from the modem status register. - Define this if your serial port does not use this pin. - -Example: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clock-frequency = <3686400>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - dcd-override; - dsr-override; - cts-override; - ri-override; - }; - -Example with one clock: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; - -Example with two clocks: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>, <&apb_pclk>; - clock-names = "baudclk", "apb_pclk"; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml new file mode 100644 index 000000000000..b42002542690 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare ABP UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a06g032-uart + - renesas,r9a06g033-uart + - const: renesas,rzn1-uart + - items: + - enum: + - rockchip,px30-uart + - rockchip,rk3036-uart + - rockchip,rk3066-uart + - rockchip,rk3188-uart + - rockchip,rk3288-uart + - rockchip,rk3328-uart + - rockchip,rk3368-uart + - rockchip,rk3399-uart + - rockchip,rv1108-uart + - const: snps,dw-apb-uart + - items: + - enum: + - brcm,bcm11351-dw-apb-uart + - brcm,bcm21664-dw-apb-uart + - const: snps,dw-apb-uart + - const: snps,dw-apb-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: true + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: baudclk + - const: apb_pclk + + snps,uart-16550-compatible: + description: reflects the value of UART_16550_COMPATIBLE configuration + parameter. Define this if your UART does not implement the busy functionality. + type: boolean + + resets: + maxItems: 1 + + reg-shift: true + + reg-io-width: true + + dcd-override: + description: Override the DCD modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + dsr-override: + description: Override the DTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + cts-override: + description: Override the CTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + ri-override: + description: Override the RI modem status signal. This signal will always + be reported as inactive instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. + type: boolean + +required: + - compatible + - reg + - interrupts + +examples: + - | + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; + }; + + - | + // Example with one clock: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + - | + // Example with two clocks: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; +... |