diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/fsl,fec.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/fsl,fec.yaml | 213 |
1 files changed, 213 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml new file mode 100644 index 000000000000..7fa11f6622b1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml @@ -0,0 +1,213 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,fec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Fast Ethernet Controller (FEC) + +maintainers: + - Joakim Zhang <qiangqing.zhang@nxp.com> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - fsl,imx25-fec + - fsl,imx27-fec + - fsl,imx28-fec + - fsl,imx6q-fec + - fsl,mvf600-fec + - items: + - enum: + - fsl,imx53-fec + - fsl,imx6sl-fec + - const: fsl,imx25-fec + - items: + - enum: + - fsl,imx35-fec + - fsl,imx51-fec + - const: fsl,imx27-fec + - items: + - enum: + - fsl,imx6ul-fec + - fsl,imx6sx-fec + - const: fsl,imx6q-fec + - items: + - enum: + - fsl,imx7d-fec + - const: fsl,imx6sx-fec + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + interrupt-names: + description: + Names of the interrupts listed in interrupts property in the same order. + The defaults if not specified are + __Number of interrupts__ __Default__ + 1 "int0" + 2 "int0", "pps" + 3 "int0", "int1", "int2" + 4 "int0", "int1", "int2", "pps" + The order may be changed as long as they correspond to the interrupts + property. Currently, only i.mx7 uses "int1" and "int2". They correspond to + tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. + For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse + per second interrupt associated with 1588 precision time protocol(PTP). + + clocks: + minItems: 2 + maxItems: 5 + description: + The "ipg", for MAC ipg_clk_s, ipg_clk_mac_s that are for register accessing. + The "ahb", for MAC ipg_clk, ipg_clk_mac that are bus clock. + The "ptp"(option), for IEEE1588 timer clock that requires the clock. + The "enet_clk_ref"(option), for MAC transmit/receiver reference clock like + RGMII TXC clock or RMII reference clock. It depends on board design, + the clock is required if RGMII TXC and RMII reference clock source from + SOC internal PLL. + The "enet_out"(option), output clock for external device, like supply clock + for PHY. The clock is required if PHY clock source from SOC. + + clock-names: + minItems: 2 + maxItems: 5 + contains: + enum: + - ipg + - ahb + - ptp + - enet_clk_ref + - enet_out + + phy-mode: true + + phy-handle: true + + fixed-link: true + + local-mac-address: true + + mac-address: true + + phy-supply: + description: + Regulator that powers the Ethernet PHY. + + fsl,num-tx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the tx queue number, otherwise set tx queue number to 1. + + fsl,num-rx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the rx queue number, otherwise set rx queue number to 1. + + fsl,magic-packet: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present, indicates that the hardware supports waking up via magic packet. + + fsl,err006687-workaround-present: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present indicates that the system has the hardware workaround for + ERR006687 applied and does not need a software workaround. + + fsl,stop-mode: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Register bits of stop mode control, the format is <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. + + mdio: + type: object + description: + Specifies the mdio bus in the FEC, used as a container for phy nodes. + + # Deprecated optional properties: + # To avoid these, create a phy node according to ethernet-phy.yaml in the same + # directory, and point the FEC's "phy-handle" property to it. Then use + # the phy's reset binding, again described by ethernet-phy.yaml. + + phy-reset-gpios: + deprecated: true + description: + Should specify the gpio for phy reset. + + phy-reset-duration: + deprecated: true + description: + Reset duration in milliseconds. Should present only if property + "phy-reset-gpios" is available. Missing the property will have the + duration be 1 millisecond. Numbers greater than 1000 are invalid + and 1 millisecond will be used instead. + + phy-reset-active-high: + deprecated: true + description: + If present then the reset sequence using the GPIO specified in the + "phy-reset-gpios" property is reversed (H=reset state, L=operation state). + + phy-reset-post-delay: + deprecated: true + description: + Post reset delay in milliseconds. If present then a delay of phy-reset-post-delay + milliseconds will be observed after the phy-reset-gpios has been toggled. + Can be omitted thus no delay is observed. Delay is in range of 1ms to 1000ms. + Other delays are invalid. + +required: + - compatible + - reg + - interrupts + +# FIXME: We had better set additionalProperties to false to avoid invalid or at +# least undocumented properties. However, PHY may have a deprecated option to +# place PHY OF properties in the MAC node, such as Micrel PHY, and we can find +# these boards which is based on i.MX6QDL. +additionalProperties: true + +examples: + - | + ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + }; + + ethernet@83fed000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fed000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; |