diff options
Diffstat (limited to 'Documentation/cdrom/aztcd')
| -rw-r--r-- | Documentation/cdrom/aztcd | 822 |
1 files changed, 0 insertions, 822 deletions
diff --git a/Documentation/cdrom/aztcd b/Documentation/cdrom/aztcd deleted file mode 100644 index 6bf0290ef7ce..000000000000 --- a/Documentation/cdrom/aztcd +++ /dev/null @@ -1,822 +0,0 @@ -$Id: README.aztcd,v 2.60 1997/11/29 09:51:25 root Exp root $ - Readme-File Documentation/cdrom/aztcd - for - AZTECH CD-ROM CDA268-01A, ORCHID CD-3110, - OKANO/WEARNES CDD110, CONRAD TXC, CyCDROM CR520, CR540 - CD-ROM Drives - Version 2.6 and newer - (for other drives see 6.-8.) - -NOTE: THIS DRIVER WILL WORK WITH THE CD-ROM DRIVES LISTED, WHICH HAVE - A PROPRIETARY INTERFACE (implemented on a sound card or on an - ISA-AT-bus card). - IT WILL DEFINITELY NOT WORK WITH CD-ROM DRIVES WITH *IDE*-INTERFACE, - such as the Aztech CDA269-031SE !!! (The only known exceptions are - 'faked' IDE drives like the CyCDROM CR520ie which work with aztcd - under certain conditions, see 7.). IF YOU'RE USING A CD-ROM DRIVE - WITH IDE-INTERFACE, SOMETIMES ALSO CALLED ATAPI-COMPATIBLE, PLEASE - USE THE ide-cd.c DRIVER, WRITTEN BY MARK LORD AND SCOTT SNYDER ! - THE STANDARD-KERNEL 1.2.x NOW ALSO SUPPORTS IDE-CDROM-DRIVES, SEE THE - HARDDISK (!) SECTION OF make config, WHEN COMPILING A NEW KERNEL!!! ----------------------------------------------------------------------------- - -Contents of this file: - 1. NOTE - 2. INSTALLATION - 3. CONFIGURING YOUR KERNEL - 4. RECOMPILING YOUR KERNEL - 4.1 AZTCD AS A RUN-TIME LOADABLE MODULE - 4.2 CDROM CONNECTED TO A SOUNDCARD - 5. KNOWN PROBLEMS, FUTURE DEVELOPMENTS - 5.1 MULTISESSION SUPPORT - 5.2 STATUS RECOGNITION - 5.3 DOSEMU's CDROM SUPPORT - 6. BUG REPORTS - 7. OTHER DRIVES - 8. IF YOU DON'T SUCCEED ... DEBUGGING - 9. TECHNICAL HISTORY OF THE DRIVER - 10. ACKNOWLEDGMENTS - 11. PROGRAMMING ADD ONS: CDPLAY.C - APPENDIX: Source code of cdplay.c ----------------------------------------------------------------------------- - -1. NOTE -This software has been successfully in alpha and beta test and is part of -the standard kernel since kernel 1.1.8x since December 1994. It works with -AZTECH CDA268-01A, ORCHID CDS-3110, ORCHID/WEARNES CDD110 and CONRAD TXC -(Nr.99 31 23 -series 04) and has proven to be stable with kernel -versions 1.0.9 and newer. But with any software there still may be bugs in it. -So if you encounter problems, you are invited to help us improve this software. -Please send me a detailed bug report (see chapter BUG REPORTS). You are also -invited in helping us to increase the number of drives, which are supported. - -Please read the README-files carefully and always keep a backup copy of your -old kernel, in order to reboot if something goes wrong! - -2. INSTALLATION -The driver consists of a header file 'aztcd.h', which normally should reside -in /usr/src/linux/drivers/cdrom and the source code 'aztcd.c', which normally -resides in the same place. It uses /dev/aztcd (/dev/aztcd0 in some distri- -butions), which must be a valid block device with major number 29 and reside -in directory /dev. To mount a CD-ROM, your kernel needs to have the ISO9660- -filesystem support included. - -PLEASE NOTE: aztcd.c has been developed in parallel to the linux kernel, -which had and is having many major and minor changes which are not backward -compatible. Quite definitely aztcd.c version 1.80 and newer will NOT work -in kernels older than 1.3.33. So please always use the most recent version -of aztcd.c with the appropriate linux-kernel. - -3. CONFIGURING YOUR KERNEL -If your kernel is already configured for using the AZTECH driver you will -see the following message while Linux boots: - Aztech CD-ROM Init: DriverVersion=<version number> BaseAddress=<baseaddress> - Aztech CD-ROM Init: FirmwareVersion=<firmware version id of your I/O-card>>> - Aztech CD-ROM Init: <drive type> detected - Aztech CD-ROM Init: End -If the message looks different and you are sure to have a supported drive, -it may have a different base address. The Aztech driver does look for the -CD-ROM drive at the base address specified in aztcd.h at compile time. This -address can be overwritten by boot parameter aztcd=....You should reboot and -start Linux with boot parameter aztcd=<base address>, e.g. aztcd=0x320. If -you do not know the base address, start your PC with DOS and look at the boot -message of your CD-ROM's DOS driver. If that still does not help, use boot -parameter aztcd=<base address>,0x79 , this tells aztcd to try a little harder. -aztcd may be configured to use autoprobing the base address by recompiling -it (see chapter 4.). - -If the message looks correct, as user 'root' you should be able to mount the -drive by - mount -t iso9660 -r /dev/aztcd0 /mnt -and use it as any other filesystem. (If this does not work, check if -/dev/aztcd0 and /mnt do exist and create them, if necessary by doing - mknod /dev/aztcd0 b 29 0 - mkdir /mnt - -If you still get a different message while Linux boots or when you get the -message, that the ISO9660-filesystem is not supported by your kernel, when -you try to mount the CD-ROM drive, you have to recompile your kernel. - -If you do *not* have an Aztech/Orchid/Okano/Wearnes/TXC drive and want to -bypass drive detection during Linux boot up, start with boot parameter aztcd=0. - -Most distributions nowadays do contain a boot disk image containing aztcd. -Please note, that this driver will not work with IDE/ATAPI drives! With these -you must use ide-cd.c instead. - -4. RECOMPILING YOUR KERNEL -If your kernel is not yet configured for the AZTECH driver and the ISO9660- -filesystem, you have to recompile your kernel: - -- Edit aztcd.h to set the I/O-address to your I/O-Base address (AZT_BASE_ADDR), - the driver does not use interrupts or DMA, so if you are using an AZTECH - CD268, an ORCHID CD-3110 or ORCHID/WEARNES CDD110 that's the only item you - have to set up. If you have a soundcard, read chapter 4.2. - Users of other drives should read chapter OTHER DRIVES of this file. - You also can configure that address by kernel boot parameter aztcd=... -- aztcd may be configured to use autoprobing the base address by setting - AZT_BASE_ADDR to '-1'. In that case aztcd probes the addresses listed - under AZT_BASE_AUTO. But please remember, that autoprobing always may - incorrectly influence other hardware components too! -- There are some other points, which may be configured, e.g. auto-eject the - CD when unmounting a drive, tray locking etc., see aztcd.h for details. -- If you're using a linux kernel version prior to 2.1.0, in aztcd.h - uncomment the line '#define AZT_KERNEL_PRIOR_2_1' -- Build a new kernel, configure it for 'Aztech/Orchid/Okano/Wearnes support' - (if you want aztcd to be part of the kernel). Do not configure it for - 'Aztech... support', if you want to use aztcd as a run time loadable module. - But in any case you must have the ISO9660-filesystem included in your - kernel. -- Activate the new kernel, normally this is done by running LILO (don't for- - get to configure it before and to keep a copy of your old kernel in case - something goes wrong!). -- Reboot -- If you've included aztcd in your kernel, you now should see during boot - some messages like - Aztech CD-ROM Init: DriverVersion=<version number> BaseAddress=<baseaddress> - Aztech CD-ROM Init: FirmwareVersion=<firmware version id of your I/O-card> - Aztech CD-ROM Init: <drive type> detected - Aztech CD-ROM Init: End -- If you have not included aztcd in your kernel, but want to load aztcd as a - run time loadable module see 4.1. -- If the message looks correct, as user 'root' you should be able to mount - the drive by - mount -t iso9660 -r /dev/aztcd0 /mnt - and use it as any other filesystem. (If this does not work, check if - /dev/aztcd0 and /mnt do exist and create them, if necessary by doing - mknod /dev/aztcd0 b 29 0 - mkdir /mnt -- If this still does not help, see chapters OTHER DRIVES and DEBUGGING. - -4.1 AZTCD AS A RUN-TIME LOADABLE MODULE -If you do not need aztcd permanently, you can also load and remove the driver -during runtime via insmod and rmmod. To build aztcd as a loadable module you -must configure your kernel for AZTECH module support (answer 'm' when con- -figuring the kernel). Anyhow, you may run into problems, if the version of -your boot kernel is not the same than the source kernel version, from which -you create the modules. So rebuild your kernel, if necessary. - -Now edit the base address of your AZTECH interface card in -/usr/src/linux/drivers/cdrom/aztcd.h to the appropriate value. -aztcd may be configured to use autoprobing the base address by setting -AZT_BASE_ADDR to '-1'. In that case aztcd probes the addresses listed -under AZT_BASE_AUTO. But please remember, that autoprobing always may -incorrectly influence other hardware components too! -There are also some special features which may be configured, e.g. -auto-eject a CD when unmounting the drive etc; see aztcd.h for details. -Then change to /usr/src/linux and do a - make modules - make modules_install -After that you can run-time load the driver via - insmod /lib/modules/X.X.X/misc/aztcd.o -and remove it via rmmod aztcd. -If you did not set the correct base address in aztcd.h, you can also supply the -base address when loading the driver via - insmod /lib/modules/X.X.X/misc/aztcd.o aztcd=<base address> -Again specifying aztcd=-1 will cause autoprobing. -If you do not have the iso9660-filesystem in your boot kernel, you also have -to load it before you can mount the CDROM: - insmod /lib/modules/X.X.X/fs/isofs.o -The mount procedure works as described in 4. above. -(In all commands 'X.X.X' is the current linux kernel version number) - -4.2 CDROM CONNECTED TO A SOUNDCARD -Most soundcards do have a bus interface to the CDROM-drive. In many cases -this soundcard needs to be configured, before the CDROM can be used. This -configuration procedure consists of writing some kind of initialization -data to the soundcard registers. The AZTECH-CDROM driver in the moment does -only support one type of soundcard (SoundWave32). Users of other soundcards -should try to boot DOS first and let their DOS drivers initialize the -soundcard and CDROM, then warm boot (or use loadlin) their PC to start -Linux. -Support for the CDROM-interface of SoundWave32-soundcards is directly -implemented in the AZTECH driver. Please edit linux/drivers/cdrom/aztdc.h, -uncomment line '#define AZT_SW32' and set the appropriate value for -AZT_BASE_ADDR and AZT_SW32_BASE_ADDR. This support was tested with an Orchid -CDS-3110 connected to a SoundWave32. -If you want your soundcard to be supported, find out, how it needs to be -configured and mail me (see 6.) the appropriate information. - -5. KNOWN PROBLEMS, FUTURE DEVELOPMENTS -5.1 MULTISESSION SUPPORT -Multisession support for CD's still is a myth. I implemented and tested a basic -support for multisession and XA CDs, but I still have not enough CDs and appli- -cations to test it rigorously. So if you'd like to help me, please contact me -(Email address see below). As of version 1.4 and newer you can enable the -multisession support in aztcd.h by setting AZT_MULTISESSION to 1. Doing so -will cause the ISO9660-filesystem to deal with multisession CDs, ie. redirect -requests to the Table of Contents (TOC) information from the last session, -which contains the info of all previous sessions etc.. If you do set -AZT_MULTISESSION to 0, you can use multisession CDs anyway. In that case the -drive's firmware will do automatic redirection. For the ISO9660-filesystem any -multisession CD will then look like a 'normal' single session CD. But never- -theless the data of all sessions are viewable and accessible. So with practical- -ly all real world applications you won't notice the difference. But as future -applications may make use of advanced multisession features, I've started to -implement the interface for the ISO9660 multisession interface via ioctl -CDROMMULTISESSION. - -5.2 STATUS RECOGNITION -The drive status recognition does not work correctly in all cases. Changing -a disk or having the door open, when a drive is already mounted, is detected -by the Aztech driver itself, but nevertheless causes multiple read attempts -by the different layers of the ISO9660-filesystem driver, which finally timeout, -so you have to wait quite a little... But isn't it bad style to change a disk -in a mounted drive, anyhow ?! - -The driver uses busy wait in most cases for the drive handshake (macros -STEN_LOW and DTEN_LOW). I tested with a 486/DX2 at 66MHz and a Pentium at -60MHz and 90MHz. Whenever you use a much faster machine you are likely to get -timeout messages. In that case edit aztcd.h and increase the timeout value -AZT_TIMEOUT. - -For some 'slow' drive commands I implemented waiting with a timer waitqueue -(macro STEN_LOW_WAIT). If you get this timeout message, you may also edit -aztcd.h and increase the timeout value AZT_STATUS_DELAY. The waitqueue has -shown to be a little critical. If you get kernel panic messages, edit aztcd.c -and substitute STEN_LOW_WAIT by STEN_LOW. Busy waiting with STEN_LOW is more -stable, but also causes CPU overhead. - -5.3 DOSEMU's CD-ROM SUPPORT -With release 1.20 aztcd was modified to allow access to CD-ROMS when running -under dosemu-0.60.0 aztcd-versions before 1.20 are most likely to crash -Linux, when a CD-ROM is accessed under dosemu. This problem has partly been -fixed, but still when accessing a directory for the first time the system -might hang for some 30sec. So be patient, when using dosemu's CD-ROM support -in combination with aztcd :-) ! -This problem has now (July 1995) been fixed by a modification to dosemu's -CD-ROM driver. The new version came with dosemu-0.60.2, see dosemu's -README.CDROM. - -6. BUG REPORTS -Please send detailed bug reports and bug fixes via EMail to - - Werner.Zimmermann@fht-esslingen.de - -Please include a description of your CD-ROM drive type and interface card, -the exact firmware message during Linux bootup, the version number of the -AZTECH-CDROM-driver and the Linux kernel version. Also a description of your -system's other hardware could be of interest, especially microprocessor type, -clock frequency, other interface cards such as soundcards, ethernet adapter, -game cards etc.. - -I will try to collect the reports and make the necessary modifications from -time to time. I may also come back to you directly with some bug fixes and -ask you to do further testing and debugging. - -Editors of CD-ROMs are invited to send a 'cooperation' copy of their -CD-ROMs to the volunteers, who provided the CD-ROM support for Linux. My -snail mail address for such 'stuff' is - Prof. Dr. W. Zimmermann - Fachhochschule fuer Technik Esslingen - Fachbereich IT - Flandernstrasse 101 - D-73732 Esslingen - Germany - - -7. OTHER DRIVES -The following drives ORCHID CDS3110, OKANO CDD110, WEARNES CDD110 and Conrad -TXC Nr. 993123-series 04 nearly look the same as AZTECH CDA268-01A, especially -they seem to use the same command codes. So it was quite simple to make the -AZTECH driver work with these drives. - -Unfortunately I do not have any of these drives available, so I couldn't test -it myself. In some installations, it seems necessary to initialize the drive -with the DOS driver before (especially if combined with a sound card) and then -do a warm boot (CTRL-ALT-RESET) or start Linux from DOS, e.g. with 'loadlin'. - -If you do not succeed, read chapter DEBUGGING. Thanks in advance! - -Sorry for the inconvenience, but it is difficult to develop for hardware, -which you don't have available for testing. So if you like, please help us. - -If you do have a CyCDROM CR520ie thanks to Hilmar Berger's help your chances -are good, that it will work with aztcd. The CR520ie is sold as an IDE-drive -and really is connected to the IDE interface (primary at 0x1F0 or secondary -at 0x170, configured as slave, not as master). Nevertheless it is not ATAPI -compatible but still uses Aztech's command codes. - - -8. DEBUGGING : IF YOU DON'T SUCCEED, TRY THE FOLLOWING --reread the complete README file --make sure, that your drive is hardware configured for - transfer mode: polled - IRQ: not used - DMA: not used - Base Address: something like 300, 320 ... - You can check this, when you start the DOS driver, which came with your - drive. By appropriately configuring the drive and the DOS driver you can - check, whether your drive does operate in this mode correctly under DOS. If - it does not operate under DOS, it won't under Linux. - If your drive's base address is something like 0x170 or 0x1F0 (and it is - not a CyCDROM CR520ie or CR 940ie) you most likely are having an IDE/ATAPI- - compatible drive, which is not supported by aztcd.c, use ide-cd.c instead. - Make sure the Base Address is configured correctly in aztcd.h, also make - sure, that /dev/aztcd0 exists with the correct major number (compare it with - the entry in file /usr/include/linux/major.h for the Aztech drive). --insert a CD-ROM and close the tray --cold boot your PC (i.e. via the power on switch or the reset button) --if you start Linux via DOS, e.g. using loadlin, make sure, that the DOS - driver for the CD-ROM drive is not loaded (comment out the calling lines - in DOS' config.sys!) --look for the aztcd: init message during Linux init and note them exactly --log in as root and do a mount -t iso9660 /dev/aztcd0 /mnt --if you don't succeed in the first time, try several times. Try also to open - and close the tray, then mount again. Please note carefully all commands - you typed in and the aztcd-messages, which you get. --if you get an 'Aztech CD-ROM init: aborted' message, read the remarks about - the version string below. - -If this does not help, do the same with the following differences --start DOS before; make now sure, that the DOS driver for the CD-ROM is - loaded under DOS (i.e. uncomment it again in config.sys) --warm boot your PC (i.e. via CTRL-ALT-DEL) - if you have it, you can also start via loadlin (try both). - ... - Again note all commands and the aztcd-messages. - -If you see STEN_LOW or STEN_LOW_WAIT error messages, increase the timeout -values. - -If this still does not help, --look in aztcd.c for the lines #if 0 - #define AZT_TEST1 - ... - #endif - and substitute '#if 0' by '#if 1'. --recompile your kernel and repeat the above two procedures. You will now get - a bundle of debugging messages from the driver. Again note your commands - and the appropriate messages. If you have syslogd running, these messages - may also be found in syslogd's kernel log file. Nevertheless in some - installations syslogd does not yet run, when init() is called, thus look for - the aztcd-messages during init, before the login-prompt appears. - Then look in aztcd.c, to find out, what happened. The normal calling sequence - is: aztcd_init() during Linux bootup procedure init() - after doing a 'mount -t iso9660 /dev/aztcd0 /mnt' the normal calling sequence is - aztcd_open() -> Status 2c after cold reboot with CDROM or audio CD inserted - -> Status 8 after warm reboot with CDROM inserted - -> Status 2e after cold reboot with no disk, closed tray - -> Status 6e after cold reboot, mount with door open - aztUpdateToc() - aztGetDiskInfo() - aztGetQChannelInfo() repeated several times - aztGetToc() - aztGetQChannelInfo() repeated several times - a list of track information - do_aztcd_request() } - azt_transfer() } repeated several times - azt_poll } - Check, if there is a difference in the calling sequence or the status flags! - - There are a lot of other messages, eg. the ACMD-command code (defined in - aztcd.h), status info from the getAztStatus-command and the state sequence of - the finite state machine in azt_poll(). The most important are the status - messages, look how they are defined and try to understand, if they make - sense in the context where they appear. With a CD-ROM inserted the status - should always be 8, except in aztcd_open(). Try to open the tray, insert an - audio disk, insert no disk or reinsert the CD-ROM and check, if the status - bits change accordingly. The status bits are the most likely point, where - the drive manufacturers may implement changes. - -If you still don't succeed, a good point to start is to look in aztcd.c in -function aztcd_init, where the drive should be detected during init. Do the -following: --reboot the system with boot parameter 'aztcd=<your base address>,0x79'. With - parameter 0x79 most of the drive version detection is bypassed. After that - you should see the complete version string including leading and trailing - blanks during init. - Now adapt the statement - if ((result[1]=='A')&&(result[2]=='Z' ...) - in aztcd_init() to exactly match the first 3 or 4 letters you have seen. --Another point is the 'smart' card detection feature in aztcd_init(). Normally - the CD-ROM drive is ready, when aztcd_init is trying to read the version - string and a time consuming ACMD_SOFT_RESET command can be avoided. This is - detected by looking, if AFL_OP_OK can be read correctly. If the CD-ROM drive - hangs in some unknown state, e.g. because of an error before a warm start or - because you first operated under DOS, even the version string may be correct, - but the following commands will not. Then change the code in such a way, - that the ACMD_SOFT_RESET is issued in any case, by substituting the - if-statement 'if ( ...=AFL_OP_OK)' by 'if (1)'. - -If you succeed, please mail me the exact version string of your drive and -the code modifications, you have made together with a short explanation. -If you don't succeed, you may mail me the output of the debugging messages. -But remember, they are only useful, if they are exact and complete and you -describe in detail your hardware setup and what you did (cold/warm reboot, -with/without DOS, DOS-driver started/not started, which Linux-commands etc.) - - -9. TECHNICAL HISTORY OF THE DRIVER -The AZTECH-Driver is a rework of the Mitsumi-Driver. Four major items had to -be reworked: - -a) The Mitsumi drive does issue complete status information acknowledging -each command, the Aztech drive does only signal that the command was -processed. So whenever the complete status information is needed, an extra -ACMD_GET_STATUS command is issued. The handshake procedure for the drive -can be found in the functions aztSendCmd(), sendAztCmd() and getAztStatus(). - -b) The Aztech Drive does not have a ACMD_GET_DISK_INFO command, so the -necessary info about the number of tracks (firstTrack, lastTrack), disk -length etc. has to be read from the TOC in the lead in track (see function -aztGetDiskInfo()). - -c) Whenever data is read from the drive, the Mitsumi drive is started with a -command to read an indefinite (0xffffff) number of sectors. When the appropriate -number of sectors is read, the drive is stopped by a ACDM_STOP command. This -does not work with the Aztech drive. I did not find a way to stop it. The -stop and pause commands do only work in AUDIO mode but not in DATA mode. -Therefore I had to modify the 'finite state machine' in function azt_poll to -only read a certain number of sectors and then start a new read on demand. As I -have not completely understood, how the buffer/caching scheme of the Mitsumi -driver was implemented, I am not sure, if I have covered all cases correctly, -whenever you get timeout messages, the bug is most likely to be in that -function azt_poll() around switch(cmd) .... case ACD_S_DATA. - -d) I did not get information about changing drive mode. So I doubt, that the -code around function azt_poll() case AZT_S_MODE does work. In my test I have -not been able to switch to reading in raw mode. For reading raw mode, Aztech -uses a different command than for cooked mode, which I only have implemen- -ted in the ioctl-section but not in the section which is used by the ISO9660. - -The driver was developed on an AST PC with Intel 486/DX2, 8MB RAM, 340MB IDE -hard disk and on an AST PC with Intel Pentium 60MHz, 16MB RAM, 520MB IDE -running Linux kernel version 1.0.9 from the LST 1.8 Distribution. The kernel -was compiled with gcc.2.5.8. My CD-ROM drive is an Aztech CDA268-01A. My -drive says, that it has Firmware Version AZT26801A1.3. It came with an ISA-bus -interface card and works with polled I/O without DMA and without interrupts. -The code for all other drives was 'remote' tested and debugged by a number of -volunteers on the Internet. - -Points, where I feel that possible problems might be and all points where I -did not completely understand the drive's behaviour or trust my own code are -marked with /*???*/ in the source code. There are also some parts in the -Mitsumi driver, where I did not completely understand their code. - - -10. ACKNOWLEDGMENTS -Without the help of P.Bush, Aztech, who delivered technical information -about the Aztech Drive and without the help of E.Moenkeberg, GWDG, who did a -great job in analyzing the command structure of various CD-ROM drives, this -work would not have been possible. E.Moenkeberg was also a great help in -making the software 'kernel ready' and in answering many of the CDROM-related -questions in the newsgroups. He really is *the* Linux CD-ROM guru. Thanks -also to all the guys on the Internet, who collected valuable technical -information about CDROMs. - -Joe Nardone (joe@access.digex.net) was a patient tester even for my first -trial, which was more than slow, and made suggestions for code improvement. -Especially the 'finite state machine' azt_poll() was rewritten by Joe to get -clean C code and avoid the ugly 'gotos', which I copied from mcd.c. - -Robby Schirmer (schirmer@fmi.uni-passau.de) tested the audio stuff (ioctls) -and suggested a lot of patches for them. - -Joseph Piskor and Peter Nugent were the first users with the ORCHID CD3110 -and also were very patient with the problems which occurred. - -Reinhard Max delivered the information for the CDROM-interface of the -SoundWave32 soundcards. - -Jochen Kunz and Olaf Kaluza delivered the information for supporting Conrad's -TXC drive. - -Hilmar Berger delivered the patches for supporting CyCDROM CR520ie. - -Anybody, who is interested in these items should have a look at 'ftp.gwdg.de', -directory 'pub/linux/cdrom' and at 'ftp.cdrom.com', directory 'pub/cdrom'. - -11. PROGRAMMING ADD ONs: cdplay.c -You can use the ioctl-functions included in aztcd.c in your own programs. As -an example on how to do this, you will find a tiny CD Player for audio CDs -named 'cdplay.c'. It allows you to play audio CDs. You can play a specified -track, pause and resume or skip tracks forward and backwards. If you quit the -program without stopping the drive, playing is continued. You can also -(mis)use cdplay to read and hexdump data disks. You can find the code in the -APPENDIX of this file, which you should cut out with an editor and store in a -separate file 'cdplay.c'. To compile it and make it executable, do - gcc -s -Wall -O2 -L/usr/lib cdplay.c -o /usr/local/bin/cdplay # compiles it - chmod +755 /usr/local/bin/cdplay # makes it executable - ln -s /dev/aztcd0 /dev/cdrom # creates a link - (for /usr/lib substitute the top level directory, where your include files - reside, and for /usr/local/bin the directory, where you want the executable - binary to reside ) - -You have to set the correct permissions for cdplay *and* for /dev/mcd0 or -/dev/aztcd0 in order to use it. Remember, that you should not have /dev/cdrom -mounted, when you're playing audio CDs. - -This program is just a hack for testing the ioctl-functions in aztcd.c. I will -not maintain it, so if you run into problems, discard it or have a look into -the source code 'cdplay.c'. The program does only contain a minimum of user -protection and input error detection. If you use the commands in the wrong -order or if you try to read a CD at wrong addresses, you may get error messages -or even hang your machine. If you get STEN_LOW, STEN_LOW_WAIT or segment violation -error messages when using cdplay, after that, the system might not be stable -any more, so you'd better reboot. As the ioctl-functions run in kernel mode, -most normal Linux-multitasking protection features do not work. By using -uninitialized 'wild' pointers etc., it is easy to write to other users' data -and program areas, destroy kernel tables etc.. So if you experiment with ioctls -as always when you are doing systems programming and kernel hacking, you -should have a backup copy of your system in a safe place (and you also -should try restoring from a backup copy first)! - -A reworked and improved version called 'cdtester.c', which has yet more -features for testing CDROM-drives can be found in -Documentation/cdrom/sbpcd, written by E.Moenkeberg. - -Werner Zimmermann -Fachhochschule fuer Technik Esslingen -(EMail: Werner.Zimmermann@fht-esslingen.de) -October, 1997 - ---------------------------------------------------------------------------- -APPENDIX: Source code of cdplay.c - -/* Tiny Audio CD Player - - Copyright 1994, 1995, 1996 Werner Zimmermann (Werner.Zimmermann@fht-esslingen.de) - -This program originally was written to test the audio functions of the -AZTECH.CDROM-driver, but it should work with every CD-ROM drive. Before -using it, you should set a symlink from /dev/cdrom to your real CDROM -device. - -The GNU General Public License applies to this program. - -History: V0.1 W.Zimmermann: First release. Nov. 8, 1994 - V0.2 W.Zimmermann: Enhanced functionality. Nov. 9, 1994 - V0.3 W.Zimmermann: Additional functions. Nov. 28, 1994 - V0.4 W.Zimmermann: fixed some bugs. Dec. 17, 1994 - V0.5 W.Zimmermann: clean 'scanf' commands without compiler warnings - Jan. 6, 1995 - V0.6 W.Zimmermann: volume control (still experimental). Jan. 24, 1995 - V0.7 W.Zimmermann: read raw modified. July 26, 95 -*/ - -#include <stdio.h> -#include <ctype.h> -#include <sys/ioctl.h> -#include <sys/types.h> -#include <fcntl.h> -#include <unistd.h> -#include <linux/cdrom.h> -#include <linux/../../drivers/cdrom/aztcd.h> - -void help(void) -{ printf("Available Commands: STOP s EJECT/CLOSE e QUIT q\n"); - printf(" PLAY TRACK t PAUSE p RESUME r\n"); - printf(" NEXT TRACK n REPEAT LAST l HELP h\n"); - printf(" SUB CHANNEL c TRACK INFO i PLAY AT a\n"); - printf(" READ d READ RAW w VOLUME v\n"); -} - -int main(void) -{ int handle; - unsigned char command=' ', ini=0, first=1, last=1; - unsigned int cmd, i,j,k, arg1,arg2,arg3; - struct cdrom_ti ti; - struct cdrom_tochdr tocHdr; - struct cdrom_subchnl subchnl; - struct cdrom_tocentry entry; - struct cdrom_msf msf; - union { struct cdrom_msf msf; - unsigned char buf[CD_FRAMESIZE_RAW]; - } azt; - struct cdrom_volctrl volctrl; - - printf("\nMini-Audio CD-Player V0.72 (C) 1994,1995,1996 W.Zimmermann\n"); - handle=open("/dev/cdrom",O_RDWR); - ioctl(handle,CDROMRESUME); - - if (handle<=0) - { printf("Drive Error: already playing, no audio disk, door open\n"); - printf(" or no permission (you must be ROOT in order to use this program)\n"); - } - else - { help(); - while (1) - { printf("Type command (h = help): "); - scanf("%s",&command); - switch (command) - { case 'e': cmd=CDROMEJECT; - ioctl(handle,cmd); - break; - case 'p': if (!ini) - { printf("Command not allowed - play track first\n"); - } - else - { cmd=CDROMPAUSE; - if (ioctl(handle,cmd)) printf("Drive Error\n"); - } - break; - case 'r': if (!ini) - { printf("Command not allowed - play track first\n"); - } - else - { cmd=CDROMRESUME; - if (ioctl(handle,cmd)) printf("Drive Error\n"); - } - break; - case 's': cmd=CDROMPAUSE; - if (ioctl(handle,cmd)) printf("Drive error or already stopped\n"); - cmd=CDROMSTOP; - if (ioctl(handle,cmd)) printf("Drive error\n"); - break; - case 't': cmd=CDROMREADTOCHDR; - if (ioctl(handle,cmd,&tocHdr)) printf("Drive Error\n"); - first=tocHdr.cdth_trk0; - last= tocHdr.cdth_trk1; - if ((first==0)||(first>last)) - { printf ("--could not read TOC\n"); - } - else - { printf("--first track: %d --last track: %d --enter track number: ",first,last); - cmd=CDROMPLAYTRKIND; - scanf("%i",&arg1); - ti.cdti_trk0=arg1; - if (ti.cdti_trk0<first) ti.cdti_trk0=first; - if (ti.cdti_trk0>last) ti.cdti_trk0=last; - ti.cdti_ind0=0; - ti.cdti_trk1=last; - ti.cdti_ind1=0; - if (ioctl(handle,cmd,&ti)) printf("Drive Error\n"); - ini=1; - } - break; - case 'n': if (!ini++) - { if (ioctl(handle,CDROMREADTOCHDR,&tocHdr)) printf("Drive Error\n"); - first=tocHdr.cdth_trk0; - last= tocHdr.cdth_trk1; - ti.cdti_trk0=first-1; - } - if ((first==0)||(first>last)) - { printf ("--could not read TOC\n"); - } - else - { cmd=CDROMPLAYTRKIND; - if (++ti.cdti_trk0 > last) ti.cdti_trk0=last; - ti.cdti_ind0=0; - ti.cdti_trk1=last; - ti.cdti_ind1=0; - if (ioctl(handle,cmd,&ti)) printf("Drive Error\n"); - ini=1; - } - break; - case 'l': if (!ini++) - { if (ioctl(handle,CDROMREADTOCHDR,&tocHdr)) printf("Drive Error\n"); - first=tocHdr.cdth_trk0; - last= tocHdr.cdth_trk1; - ti.cdti_trk0=first+1; - } - if ((first==0)||(first>last)) - { printf ("--could not read TOC\n"); - } - else - { cmd=CDROMPLAYTRKIND; - if (--ti.cdti_trk0 < first) ti.cdti_trk0=first; - ti.cdti_ind0=0; - ti.cdti_trk1=last; - ti.cdti_ind1=0; - if (ioctl(handle,cmd,&ti)) printf("Drive Error\n"); - ini=1; - } - break; - case 'c': subchnl.cdsc_format=CDROM_MSF; - if (ioctl(handle,CDROMSUBCHNL,&subchnl)) - printf("Drive Error\n"); - else - { printf("AudioStatus:%s Track:%d Mode:%d MSF=%d:%d:%d\n", \ - subchnl.cdsc_audiostatus==CDROM_AUDIO_PLAY ? "PLAYING":"NOT PLAYING",\ - subchnl.cdsc_trk,subchnl.cdsc_adr, \ - subchnl.cdsc_absaddr.msf.minute, subchnl.cdsc_absaddr.msf.second, \ - subchnl.cdsc_absaddr.msf.frame); - } - break; - case 'i': if (!ini) - { printf("Command not allowed - play track first\n"); - } - else - { cmd=CDROMREADTOCENTRY; - printf("Track No.: "); - scanf("%d",&arg1); - entry.cdte_track=arg1; - if (entry.cdte_track<first) entry.cdte_track=first; - if (entry.cdte_track>last) entry.cdte_track=last; - entry.cdte_format=CDROM_MSF; - if (ioctl(handle,cmd,&entry)) - { printf("Drive error or invalid track no.\n"); - } - else - { printf("Mode %d Track, starts at %d:%d:%d\n", \ - entry.cdte_adr,entry.cdte_addr.msf.minute, \ - entry.cdte_addr.msf.second,entry.cdte_addr.msf.frame); - } - } - break; - case 'a': cmd=CDROMPLAYMSF; - printf("Address (min:sec:frame) "); - scanf("%d:%d:%d",&arg1,&arg2,&arg3); - msf.cdmsf_min0 =arg1; - msf.cdmsf_sec0 =arg2; - msf.cdmsf_frame0=arg3; - if (msf.cdmsf_sec0 > 59) msf.cdmsf_sec0 =59; - if (msf.cdmsf_frame0> 74) msf.cdmsf_frame0=74; - msf.cdmsf_min1=60; - msf.cdmsf_sec1=00; - msf.cdmsf_frame1=00; - if (ioctl(handle,cmd,&msf)) - { printf("Drive error or invalid address\n"); - } - break; -#ifdef AZT_PRIVATE_IOCTLS /*not supported by every CDROM driver*/ - case 'd': cmd=CDROMREADCOOKED; - printf("Address (min:sec:frame) "); - scanf("%d:%d:%d",&arg1,&arg2,&arg3); - azt.msf.cdmsf_min0 =arg1; - azt.msf.cdmsf_sec0 =arg2; - azt.msf.cdmsf_frame0=arg3; - if (azt.msf.cdmsf_sec0 > 59) azt.msf.cdmsf_sec0 =59; - if (azt.msf.cdmsf_frame0> 74) azt.msf.cdmsf_frame0=74; - if (ioctl(handle,cmd,&azt.msf)) - { printf("Drive error, invalid address or unsupported command\n"); - } - k=0; - getchar(); - for (i=0;i<128;i++) - { printf("%4d:",i*16); - for (j=0;j<16;j++) - { printf("%2x ",azt.buf[i*16+j]); - } - for (j=0;j<16;j++) - { if (isalnum(azt.buf[i*16+j])) - printf("%c",azt.buf[i*16+j]); - else - printf("."); - } - printf("\n"); - k++; - if (k>=20) - { printf("press ENTER to continue\n"); - getchar(); - k=0; - } - } - break; - case 'w': cmd=CDROMREADRAW; - printf("Address (min:sec:frame) "); - scanf("%d:%d:%d",&arg1,&arg2,&arg3); - azt.msf.cdmsf_min0 =arg1; - azt.msf.cdmsf_sec0 =arg2; - azt.msf.cdmsf_frame0=arg3; - if (azt.msf.cdmsf_sec0 > 59) azt.msf.cdmsf_sec0 =59; - if (azt.msf.cdmsf_frame0> 74) azt.msf.cdmsf_frame0=74; - if (ioctl(handle,cmd,&azt)) - { printf("Drive error, invalid address or unsupported command\n"); - } - k=0; - for (i=0;i<147;i++) - { printf("%4d:",i*16); - for (j=0;j<16;j++) - { printf("%2x ",azt.buf[i*16+j]); - } - for (j=0;j<16;j++) - { if (isalnum(azt.buf[i*16+j])) - printf("%c",azt.buf[i*16+j]); - else - printf("."); - } - printf("\n"); - k++; - if (k>=20) - { getchar(); - k=0; - } - } - break; -#endif - case 'v': cmd=CDROMVOLCTRL; - printf("--Channel 0 Left (0-255): "); - scanf("%d",&arg1); - printf("--Channel 1 Right (0-255): "); - scanf("%d",&arg2); - volctrl.channel0=arg1; - volctrl.channel1=arg2; - volctrl.channel2=0; - volctrl.channel3=0; - if (ioctl(handle,cmd,&volctrl)) - { printf("Drive error or unsupported command\n"); - } - break; - case 'q': if (close(handle)) printf("Drive Error: CLOSE\n"); - exit(0); - case 'h': help(); - break; - default: printf("unknown command\n"); - break; - } - } - } - return 0; -} |