diff options
| -rw-r--r-- | drivers/iio/imu/adis16480.c | 97 |
1 files changed, 95 insertions, 2 deletions
diff --git a/drivers/iio/imu/adis16480.c b/drivers/iio/imu/adis16480.c index a27fe208f3ae..98a23ac50266 100644 --- a/drivers/iio/imu/adis16480.c +++ b/drivers/iio/imu/adis16480.c @@ -9,6 +9,8 @@ * */ +#include <linux/bitfield.h> +#include <linux/of_irq.h> #include <linux/interrupt.h> #include <linux/delay.h> #include <linux/mutex.h> @@ -107,6 +109,14 @@ #define ADIS16480_FIR_COEF_C(x) ADIS16480_FIR_COEF(0x09, (x)) #define ADIS16480_FIR_COEF_D(x) ADIS16480_FIR_COEF(0x0B, (x)) +/* ADIS16480_REG_FNCTIO_CTRL */ +#define ADIS16480_DRDY_SEL_MSK GENMASK(1, 0) +#define ADIS16480_DRDY_SEL(x) FIELD_PREP(ADIS16480_DRDY_SEL_MSK, x) +#define ADIS16480_DRDY_POL_MSK BIT(2) +#define ADIS16480_DRDY_POL(x) FIELD_PREP(ADIS16480_DRDY_POL_MSK, x) +#define ADIS16480_DRDY_EN_MSK BIT(3) +#define ADIS16480_DRDY_EN(x) FIELD_PREP(ADIS16480_DRDY_EN_MSK, x) + struct adis16480_chip_info { unsigned int num_channels; const struct iio_chan_spec *channels; @@ -116,12 +126,26 @@ struct adis16480_chip_info { unsigned int accel_max_scale; }; +enum adis16480_int_pin { + ADIS16480_PIN_DIO1, + ADIS16480_PIN_DIO2, + ADIS16480_PIN_DIO3, + ADIS16480_PIN_DIO4 +}; + struct adis16480 { const struct adis16480_chip_info *chip_info; struct adis adis; }; +static const char * const adis16480_int_pin_names[4] = { + [ADIS16480_PIN_DIO1] = "DIO1", + [ADIS16480_PIN_DIO2] = "DIO2", + [ADIS16480_PIN_DIO3] = "DIO3", + [ADIS16480_PIN_DIO4] = "DIO4", +}; + #ifdef CONFIG_DEBUG_FS static ssize_t adis16480_show_firmware_revision(struct file *file, @@ -741,8 +765,17 @@ static int adis16480_stop_device(struct iio_dev *indio_dev) static int adis16480_enable_irq(struct adis *adis, bool enable) { - return adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, - enable ? BIT(3) : 0); + uint16_t val; + int ret; + + ret = adis_read_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, &val); + if (ret < 0) + return ret; + + val &= ~ADIS16480_DRDY_EN_MSK; + val |= ADIS16480_DRDY_EN(enable); + + return adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, val); } static int adis16480_initial_setup(struct iio_dev *indio_dev) @@ -826,6 +859,62 @@ static const struct adis_data adis16480_data = { .enable_irq = adis16480_enable_irq, }; +static int adis16480_config_irq_pin(struct device_node *of_node, + struct adis16480 *st) +{ + struct irq_data *desc; + enum adis16480_int_pin pin; + unsigned int irq_type; + uint16_t val; + int i, irq = 0; + + desc = irq_get_irq_data(st->adis.spi->irq); + if (!desc) { + dev_err(&st->adis.spi->dev, "Could not find IRQ %d\n", irq); + return -EINVAL; + } + + /* Disable data ready since the default after reset is on */ + val = ADIS16480_DRDY_EN(0); + + /* + * Get the interrupt from the devicetre by reading the interrupt-names + * property. If it is not specified, use DIO1 pin as default. + * According to the datasheet, the factory default assigns DIO2 as data + * ready signal. However, in the previous versions of the driver, DIO1 + * pin was used. So, we should leave it as is since some devices might + * be expecting the interrupt on the wrong physical pin. + */ + pin = ADIS16480_PIN_DIO1; + for (i = 0; i < ARRAY_SIZE(adis16480_int_pin_names); i++) { + irq = of_irq_get_byname(of_node, adis16480_int_pin_names[i]); + if (irq > 0) { + pin = i; + break; + } + } + + val |= ADIS16480_DRDY_SEL(pin); + + /* + * Get the interrupt line behaviour. The data ready polarity can be + * configured as positive or negative, corresponding to + * IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING respectively. + */ + irq_type = irqd_get_trigger_type(desc); + if (irq_type == IRQF_TRIGGER_RISING) { /* Default */ + val |= ADIS16480_DRDY_POL(1); + } else if (irq_type == IRQF_TRIGGER_FALLING) { + val |= ADIS16480_DRDY_POL(0); + } else { + dev_err(&st->adis.spi->dev, + "Invalid interrupt type 0x%x specified\n", irq_type); + return -EINVAL; + } + /* Write the data ready configuration to the FNCTIO_CTRL register */ + return adis_write_reg_16(&st->adis, ADIS16480_REG_FNCTIO_CTRL, val); +} + static int adis16480_probe(struct spi_device *spi) { const struct spi_device_id *id = spi_get_device_id(spi); @@ -853,6 +942,10 @@ static int adis16480_probe(struct spi_device *spi) if (ret) return ret; + ret = adis16480_config_irq_pin(spi->dev.of_node, st); + if (ret) + return ret; + ret = adis_setup_buffer_and_trigger(&st->adis, indio_dev, NULL); if (ret) return ret; |