summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--arch/arm/Kconfig3
-rw-r--r--arch/arm/boot/dts/tegra-harmony.dts1
-rw-r--r--arch/arm/boot/dts/tegra-seaboard.dts4
-rw-r--r--arch/arm/configs/at91sam9g45_defconfig214
-rw-r--r--arch/arm/include/asm/hardware/it8152.h2
-rw-r--r--arch/arm/mach-imx/Kconfig1
-rw-r--r--arch/arm/mach-imx/mach-mx31_3ds.c2
-rw-r--r--arch/arm/mach-mmp/Kconfig2
-rw-r--r--arch/arm/mach-mmp/Makefile2
-rw-r--r--arch/arm/mach-mmp/clock.h8
-rw-r--r--arch/arm/mach-mmp/common.c4
-rw-r--r--arch/arm/mach-mmp/gplugd.c2
-rw-r--r--arch/arm/mach-mmp/include/mach/addr-map.h10
-rw-r--r--arch/arm/mach-mmp/include/mach/gpio-pxa.h2
-rw-r--r--arch/arm/mach-mmp/mmp2.c3
-rw-r--r--arch/arm/mach-mx5/pm-imx5.c15
-rw-r--r--arch/arm/mach-mxs/clock-mx28.c2
-rw-r--r--arch/arm/mach-omap2/board-4430sdp.c2
-rw-r--r--arch/arm/mach-omap2/irq.c4
-rw-r--r--arch/arm/mach-pxa/Kconfig38
-rw-r--r--arch/arm/mach-pxa/Makefile2
-rw-r--r--arch/arm/mach-pxa/balloon3.c10
-rw-r--r--arch/arm/mach-pxa/cm-x2xx-pci.c2
-rw-r--r--arch/arm/mach-pxa/cm-x2xx.c4
-rw-r--r--arch/arm/mach-pxa/cm-x300.c8
-rw-r--r--arch/arm/mach-pxa/include/mach/addr-map.h8
-rw-r--r--arch/arm/mach-pxa/include/mach/balloon3.h2
-rw-r--r--arch/arm/mach-pxa/include/mach/gpio-pxa.h2
-rw-r--r--arch/arm/mach-pxa/include/mach/hardware.h9
-rw-r--r--arch/arm/mach-pxa/include/mach/lpd270.h4
-rw-r--r--arch/arm/mach-pxa/include/mach/mtd-xip.h1
-rw-r--r--arch/arm/mach-pxa/include/mach/palm27x.h2
-rw-r--r--arch/arm/mach-pxa/include/mach/palmtx.h6
-rw-r--r--arch/arm/mach-pxa/include/mach/pxa27x.h2
-rw-r--r--arch/arm/mach-pxa/include/mach/pxa95x.h7
-rw-r--r--arch/arm/mach-pxa/include/mach/pxafb.h13
-rw-r--r--arch/arm/mach-pxa/include/mach/smemc.h2
-rw-r--r--arch/arm/mach-pxa/include/mach/zeus.h4
-rw-r--r--arch/arm/mach-pxa/include/mach/zylonite.h4
-rw-r--r--arch/arm/mach-pxa/irq.c4
-rw-r--r--arch/arm/mach-pxa/lpd270.c2
-rw-r--r--arch/arm/mach-pxa/palmtreo.c8
-rw-r--r--arch/arm/mach-pxa/palmtx.c8
-rw-r--r--arch/arm/mach-pxa/pxa25x.c2
-rw-r--r--arch/arm/mach-pxa/pxa27x.c2
-rw-r--r--arch/arm/mach-pxa/pxa3xx-ulpi.c2
-rw-r--r--arch/arm/mach-pxa/pxa3xx.c2
-rw-r--r--arch/arm/mach-pxa/saarb.c1
-rw-r--r--arch/arm/mach-pxa/z2.c3
-rw-r--r--arch/arm/mach-pxa/zeus.c8
-rw-r--r--arch/arm/mach-ux500/cpu.c25
-rw-r--r--arch/arm/plat-mxc/include/mach/iomux-v3.h10
-rw-r--r--arch/arm/plat-pxa/include/plat/mfp.h2
-rw-r--r--arch/arm/plat-pxa/mfp.c4
-rw-r--r--drivers/gpio/gpio-pxa.c2
-rw-r--r--drivers/misc/Kconfig2
-rw-r--r--drivers/pcmcia/pxa2xx_balloon3.c2
-rw-r--r--drivers/video/mbx/mbxfb.c6
-rw-r--r--drivers/video/pxafb.c10
59 files changed, 410 insertions, 108 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5ca86e7ab66d..1005367d0f9d 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -394,7 +394,7 @@ config ARCH_EP93XX
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_HOLES_MEMORYMODEL
select ARCH_USES_GETTIMEOFFSET
- select NEED_MEMORY_H
+ select NEED_MACH_MEMORY_H
help
This enables support for the Cirrus EP93xx series of CPUs.
@@ -2044,6 +2044,7 @@ config CPU_FREQ_PXA
bool
depends on CPU_FREQ && ARCH_PXA && PXA25x
default y
+ select CPU_FREQ_TABLE
select CPU_FREQ_DEFAULT_GOV_USERSPACE
config CPU_FREQ_S3C
diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra-harmony.dts
index e5818668d091..0e225b86b652 100644
--- a/arch/arm/boot/dts/tegra-harmony.dts
+++ b/arch/arm/boot/dts/tegra-harmony.dts
@@ -66,5 +66,6 @@
cd-gpios = <&gpio 58 0>; /* gpio PH2 */
wp-gpios = <&gpio 59 0>; /* gpio PH3 */
power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ support-8bit;
};
};
diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra-seaboard.dts
index 64cedca6fc79..a72299b8e668 100644
--- a/arch/arm/boot/dts/tegra-seaboard.dts
+++ b/arch/arm/boot/dts/tegra-seaboard.dts
@@ -25,4 +25,8 @@
wp-gpios = <&gpio 57 0>; /* gpio PH1 */
power-gpios = <&gpio 70 0>; /* gpio PI6 */
};
+
+ sdhci@c8000600 {
+ support-8bit;
+ };
};
diff --git a/arch/arm/configs/at91sam9g45_defconfig b/arch/arm/configs/at91sam9g45_defconfig
new file mode 100644
index 000000000000..c5876d244f4b
--- /dev/null
+++ b/arch/arm/configs/at91sam9g45_defconfig
@@ -0,0 +1,214 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_ARCH_AT91SAM9G45=y
+CONFIG_MACH_AT91SAM9M10G45EK=y
+CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
+CONFIG_AT91_SLOW_CLOCK=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_LEDS=y
+CONFIG_LEDS_CPU=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x71100000,25165824 root=/dev/ram0 rw"
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+CONFIG_IPV6=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CFG80211=y
+CONFIG_LIB80211=y
+CONFIG_MAC80211=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_MISC_DEVICES=y
+CONFIG_ATMEL_PWM=y
+CONFIG_ATMEL_TCLIB=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_DAVICOM_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_MACB=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_RTL8187=m
+CONFIG_ATH_COMMON=m
+CONFIG_ATH9K=m
+CONFIG_CARL9170=m
+CONFIG_B43=m
+CONFIG_B43_PHY_N=y
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_LIBERTAS_SPI=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RT2800USB_UNKNOWN=y
+CONFIG_RTL8192CU=m
+CONFIG_WL1251=m
+CONFIG_WL1251_SDIO=m
+CONFIG_WL12XX_MENU=m
+CONFIG_WL12XX=m
+CONFIG_WL12XX_SDIO=m
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=480
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=272
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=m
+CONFIG_KEYBOARD_QT2160=m
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=m
+CONFIG_TOUCHSCREEN_ATMEL_TSADCC=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+# CONFIG_HWMON is not set
+# CONFIG_MFD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FB_ATMEL=y
+CONFIG_FB_UDL=m
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SEQUENCER=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+CONFIG_SND_ATMEL_AC97C=y
+# CONFIG_SND_SPI is not set
+CONFIG_SND_USB_AUDIO=m
+# CONFIG_USB_HID is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=m
+CONFIG_USB_ZERO=m
+CONFIG_USB_AUDIO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_USB_CDC_COMPOSITE=m
+CONFIG_USB_G_MULTI=m
+CONFIG_USB_G_MULTI_CDC=y
+CONFIG_MMC=y
+# CONFIG_MMC_BLOCK_BOUNCE is not set
+CONFIG_SDIO_UART=m
+CONFIG_MMC_ATMELMCI=y
+CONFIG_MMC_ATMELMCI_DMA=y
+CONFIG_LEDS_ATMEL_PWM=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_DMATEST=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_EMBEDDED=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_SCHED_DEBUG is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO_ECB=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
+# CONFIG_CRYPTO_HW is not set
diff --git a/arch/arm/include/asm/hardware/it8152.h b/arch/arm/include/asm/hardware/it8152.h
index b3fea38d55c6..43cab498bc27 100644
--- a/arch/arm/include/asm/hardware/it8152.h
+++ b/arch/arm/include/asm/hardware/it8152.h
@@ -9,7 +9,7 @@
#ifndef __ASM_HARDWARE_IT8152_H
#define __ASM_HARDWARE_IT8152_H
-extern unsigned long it8152_base_address;
+extern void __iomem *it8152_base_address;
#define IT8152_IO_BASE (it8152_base_address + 0x03e00000)
#define IT8152_CFGREG_BASE (it8152_base_address + 0x03f00000)
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 0519dd7f034b..e9c2968005dc 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -449,6 +449,7 @@ config MACH_MX31_3DS
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_IPU_CORE
select IMX_HAVE_PLATFORM_MXC_EHCI
+ select IMX_HAVE_PLATFORM_MXC_MMC
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SPI_IMX
select MXC_ULPI if USB_ULPI
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
index 6484db525bd7..0de4d1835ea4 100644
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ b/arch/arm/mach-imx/mach-mx31_3ds.c
@@ -540,7 +540,7 @@ static const struct mxc_nand_platform_data
mx31_3ds_nand_board_info __initconst = {
.width = 1,
.hw_ecc = 1,
-#ifdef MACH_MX31_3DS_MXC_NAND_USE_BBT
+#ifdef CONFIG_MACH_MX31_3DS_MXC_NAND_USE_BBT
.flash_bbt = 1,
#endif
};
diff --git a/arch/arm/mach-mmp/Kconfig b/arch/arm/mach-mmp/Kconfig
index 56ef5f6c8116..323d4c9e9f44 100644
--- a/arch/arm/mach-mmp/Kconfig
+++ b/arch/arm/mach-mmp/Kconfig
@@ -77,7 +77,7 @@ config MACH_TETON_BGA
Say 'Y' here if you want to support the Marvell PXA168-based
Teton BGA Development Board.
-config MACH_SHEEVAD
+config MACH_GPLUGD
bool "Marvell's PXA168 GuruPlug Display (gplugD) Board"
select CPU_PXA168
help
diff --git a/arch/arm/mach-mmp/Makefile b/arch/arm/mach-mmp/Makefile
index b0ac942327aa..8f948f981646 100644
--- a/arch/arm/mach-mmp/Makefile
+++ b/arch/arm/mach-mmp/Makefile
@@ -19,4 +19,4 @@ obj-$(CONFIG_MACH_BROWNSTONE) += brownstone.o
obj-$(CONFIG_MACH_FLINT) += flint.o
obj-$(CONFIG_MACH_MARVELL_JASPER) += jasper.o
obj-$(CONFIG_MACH_TETON_BGA) += teton_bga.o
-obj-$(CONFIG_MACH_SHEEVAD) += gplugd.o
+obj-$(CONFIG_MACH_GPLUGD) += gplugd.o
diff --git a/arch/arm/mach-mmp/clock.h b/arch/arm/mach-mmp/clock.h
index 3143e994e672..149b30cd1469 100644
--- a/arch/arm/mach-mmp/clock.h
+++ b/arch/arm/mach-mmp/clock.h
@@ -30,7 +30,7 @@ extern struct clkops apmu_clk_ops;
#define APBC_CLK(_name, _reg, _fnclksel, _rate) \
struct clk clk_##_name = { \
- .clk_rst = (void __iomem *)APBC_##_reg, \
+ .clk_rst = APBC_##_reg, \
.fnclksel = _fnclksel, \
.rate = _rate, \
.ops = &apbc_clk_ops, \
@@ -38,7 +38,7 @@ struct clk clk_##_name = { \
#define APBC_CLK_OPS(_name, _reg, _fnclksel, _rate, _ops) \
struct clk clk_##_name = { \
- .clk_rst = (void __iomem *)APBC_##_reg, \
+ .clk_rst = APBC_##_reg, \
.fnclksel = _fnclksel, \
.rate = _rate, \
.ops = _ops, \
@@ -46,7 +46,7 @@ struct clk clk_##_name = { \
#define APMU_CLK(_name, _reg, _eval, _rate) \
struct clk clk_##_name = { \
- .clk_rst = (void __iomem *)APMU_##_reg, \
+ .clk_rst = APMU_##_reg, \
.enable_val = _eval, \
.rate = _rate, \
.ops = &apmu_clk_ops, \
@@ -54,7 +54,7 @@ struct clk clk_##_name = { \
#define APMU_CLK_OPS(_name, _reg, _eval, _rate, _ops) \
struct clk clk_##_name = { \
- .clk_rst = (void __iomem *)APMU_##_reg, \
+ .clk_rst = APMU_##_reg, \
.enable_val = _eval, \
.rate = _rate, \
.ops = _ops, \
diff --git a/arch/arm/mach-mmp/common.c b/arch/arm/mach-mmp/common.c
index 0ec0ca80bb3e..5720674739f0 100644
--- a/arch/arm/mach-mmp/common.c
+++ b/arch/arm/mach-mmp/common.c
@@ -27,12 +27,12 @@ EXPORT_SYMBOL(mmp_chip_id);
static struct map_desc standard_io_desc[] __initdata = {
{
.pfn = __phys_to_pfn(APB_PHYS_BASE),
- .virtual = APB_VIRT_BASE,
+ .virtual = (unsigned long)APB_VIRT_BASE,
.length = APB_PHYS_SIZE,
.type = MT_DEVICE,
}, {
.pfn = __phys_to_pfn(AXI_PHYS_BASE),
- .virtual = AXI_VIRT_BASE,
+ .virtual = (unsigned long)AXI_VIRT_BASE,
.length = AXI_PHYS_SIZE,
.type = MT_DEVICE,
},
diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c
index 32776f3739f1..69156568bc41 100644
--- a/arch/arm/mach-mmp/gplugd.c
+++ b/arch/arm/mach-mmp/gplugd.c
@@ -188,7 +188,7 @@ static void __init gplugd_init(void)
pxa168_add_eth(&gplugd_eth_platform_data);
}
-MACHINE_START(SHEEVAD, "PXA168-based GuruPlug Display (gplugD) Platform")
+MACHINE_START(GPLUGD, "PXA168-based GuruPlug Display (gplugD) Platform")
.map_io = mmp_map_io,
.nr_irqs = IRQ_BOARD_START,
.init_irq = pxa168_init_irq,
diff --git a/arch/arm/mach-mmp/include/mach/addr-map.h b/arch/arm/mach-mmp/include/mach/addr-map.h
index 3254089a644d..3e404acd6ff4 100644
--- a/arch/arm/mach-mmp/include/mach/addr-map.h
+++ b/arch/arm/mach-mmp/include/mach/addr-map.h
@@ -11,6 +11,12 @@
#ifndef __ASM_MACH_ADDR_MAP_H
#define __ASM_MACH_ADDR_MAP_H
+#ifndef __ASSEMBLER__
+#define IOMEM(x) ((void __iomem *)(x))
+#else
+#define IOMEM(x) (x)
+#endif
+
/* APB - Application Subsystem Peripheral Bus
*
* NOTE: the DMA controller registers are actually on the AXI fabric #1
@@ -18,11 +24,11 @@
* peripherals on APB, let's count it into the ABP mapping area.
*/
#define APB_PHYS_BASE 0xd4000000
-#define APB_VIRT_BASE 0xfe000000
+#define APB_VIRT_BASE IOMEM(0xfe000000)
#define APB_PHYS_SIZE 0x00200000
#define AXI_PHYS_BASE 0xd4200000
-#define AXI_VIRT_BASE 0xfe200000
+#define AXI_VIRT_BASE IOMEM(0xfe200000)
#define AXI_PHYS_SIZE 0x00200000
/* Static Memory Controller - Chip Select 0 and 1 */
diff --git a/arch/arm/mach-mmp/include/mach/gpio-pxa.h b/arch/arm/mach-mmp/include/mach/gpio-pxa.h
index c017a983eced..d14eeaf16322 100644
--- a/arch/arm/mach-mmp/include/mach/gpio-pxa.h
+++ b/arch/arm/mach-mmp/include/mach/gpio-pxa.h
@@ -7,7 +7,7 @@
#define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000)
#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x) (*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
+#define GPIO_REG(x) (GPIO_REGS_VIRT + (x))
#define NR_BUILTIN_GPIO IRQ_GPIO_NUM
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index 65d8689e40c9..7a7e8e4dde41 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -86,7 +86,8 @@ static struct mfp_addr_map mmp2_addr_map[] __initdata = {
void mmp2_clear_pmic_int(void)
{
- unsigned long mfpr_pmic, data;
+ void __iomem *mfpr_pmic;
+ unsigned long data;
mfpr_pmic = APB_VIRT_BASE + 0x1e000 + 0x2c4;
data = __raw_readl(mfpr_pmic);
diff --git a/arch/arm/mach-mx5/pm-imx5.c b/arch/arm/mach-mx5/pm-imx5.c
index e4529af0da72..be19e9ce839a 100644
--- a/arch/arm/mach-mx5/pm-imx5.c
+++ b/arch/arm/mach-mx5/pm-imx5.c
@@ -19,9 +19,13 @@
static struct clk *gpc_dvfs_clk;
+static int mx5_suspend_prepare(void)
+{
+ return clk_enable(gpc_dvfs_clk);
+}
+
static int mx5_suspend_enter(suspend_state_t state)
{
- clk_enable(gpc_dvfs_clk);
switch (state) {
case PM_SUSPEND_MEM:
mx5_cpu_lp_set(STOP_POWER_OFF);
@@ -42,11 +46,14 @@ static int mx5_suspend_enter(suspend_state_t state)
__raw_writel(0, MXC_SRPG_EMPGC1_SRPGCR);
}
cpu_do_idle();
- clk_disable(gpc_dvfs_clk);
-
return 0;
}
+static void mx5_suspend_finish(void)
+{
+ clk_disable(gpc_dvfs_clk);
+}
+
static int mx5_pm_valid(suspend_state_t state)
{
return (state > PM_SUSPEND_ON && state <= PM_SUSPEND_MAX);
@@ -54,7 +61,9 @@ static int mx5_pm_valid(suspend_state_t state)
static const struct platform_suspend_ops mx5_suspend_ops = {
.valid = mx5_pm_valid,
+ .prepare = mx5_suspend_prepare,
.enter = mx5_suspend_enter,
+ .finish = mx5_suspend_finish,
};
static int __init mx5_pm_init(void)
diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c
index 5dcc59d5b9ec..ba532279d1a1 100644
--- a/arch/arm/mach-mxs/clock-mx28.c
+++ b/arch/arm/mach-mxs/clock-mx28.c
@@ -349,7 +349,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
\
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##fr); \
reg &= ~BM_CLKCTRL_##fr##_##fs##FRAC; \
- reg |= frac; \
+ reg |= frac << BP_CLKCTRL_##fr##_##fs##FRAC; \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##fr); \
} \
\
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 484cec54882a..a3e37ff3ad18 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -133,7 +133,7 @@ static const int sdp4430_keymap[] = {
KEY(7, 6, KEY_OK),
KEY(7, 7, KEY_DOWN),
};
-static struct omap_device_pad keypad_pads[] __initdata = {
+static struct omap_device_pad keypad_pads[] = {
{ .name = "kpd_col1.kpd_col1",
.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
},
diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c
index 3a12f7586a4c..65f1be6a182c 100644
--- a/arch/arm/mach-omap2/irq.c
+++ b/arch/arm/mach-omap2/irq.c
@@ -165,8 +165,8 @@ static void __init omap_init_irq(u32 base, int nr_irqs)
omap_irq_bank_init_one(bank);
- for (i = 0, j = 0; i < bank->nr_irqs; i += 32, j += 0x20)
- omap_alloc_gc(bank->base_reg + j, i, 32);
+ for (j = 0; j < bank->nr_irqs; j += 32)
+ omap_alloc_gc(bank->base_reg + j, j, 32);
nr_of_irqs += bank->nr_irqs;
nr_banks++;
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index cd19309fd3b8..61d3c72ded84 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -2,6 +2,27 @@ if ARCH_PXA
menu "Intel PXA2xx/PXA3xx Implementations"
+config ARCH_PXA_V7
+ bool "ARMv7 (PXA95x) based systems"
+
+if ARCH_PXA_V7
+comment "Marvell Dev Platforms (sorted by hardware release time)"
+config MACH_TAVOREVB3
+ bool "PXA95x Development Platform (aka TavorEVB III)"
+ select CPU_PXA955
+
+config MACH_SAARB
+ bool "PXA955 Handheld Platform (aka SAARB)"
+ select CPU_PXA955
+endif
+
+config PXA_V7_MACH_AUTO
+ def_bool y
+ depends on ARCH_PXA_V7
+ depends on !MACH_SAARB
+ select MACH_TAVOREVB3
+
+if !ARCH_PXA_V7
comment "Intel/Marvell Dev Platforms (sorted by hardware release time)"
config ARCH_LUBBOCK
@@ -41,19 +62,11 @@ config MACH_TAVOREVB
select PXA3xx
select CPU_PXA930
-config MACH_TAVOREVB3
- bool "PXA95x Development Platform (aka TavorEVB III)"
- select CPU_PXA950
-
config MACH_SAAR
bool "PXA930 Handheld Platform (aka SAAR)"
select PXA3xx
select CPU_PXA930
-config MACH_SAARB
- bool "PXA955 Handheld Platform (aka SAARB)"
- select CPU_PXA955
-
comment "Third Party Dev Platforms (sorted by vendor name)"
config ARCH_PXA_IDP
@@ -414,6 +427,7 @@ config MACH_CENTRO
bool "Palm Centro 685 (GSM)"
default y
depends on ARCH_PXA_PALM
+ select MACH_PALM27X
select PXA27x
select IWMMXT
select PALM_TREO
@@ -425,6 +439,7 @@ config MACH_TREO680
bool "Palm Treo 680"
default y
depends on ARCH_PXA_PALM
+ select MACH_PALM27X
select PXA27x
select IWMMXT
select PALM_TREO
@@ -436,15 +451,18 @@ config MACH_RAUMFELD_RC
bool "Raumfeld Controller"
select PXA3xx
select CPU_PXA300
+ select POWER_SUPPLY
select HAVE_PWM
config MACH_RAUMFELD_CONNECTOR
bool "Raumfeld Connector"
+ select POWER_SUPPLY
select PXA3xx
select CPU_PXA300
config MACH_RAUMFELD_SPEAKER
bool "Raumfeld Speaker"
+ select POWER_SUPPLY
select PXA3xx
select CPU_PXA300
@@ -598,7 +616,7 @@ config MACH_ZIPIT2
bool "Zipit Z2 Handheld"
select PXA27x
select HAVE_PWM
-
+endif
endmenu
config PXA25x
@@ -688,6 +706,8 @@ config SHARPSL_PM
config SHARPSL_PM_MAX1111
bool
select HWMON
+ select SPI
+ select SPI_MASTER
select SENSORS_MAX1111
config PXA_HAVE_ISA_IRQS
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index cc39d17b2e07..be0f7df8685c 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -19,7 +19,7 @@ endif
obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o clock-pxa2xx.o pxa2xx.o pxa25x.o
obj-$(CONFIG_PXA27x) += mfp-pxa2xx.o clock-pxa2xx.o pxa2xx.o pxa27x.o
obj-$(CONFIG_PXA3xx) += mfp-pxa3xx.o clock-pxa3xx.o pxa3xx.o smemc.o pxa3xx-ulpi.o
-obj-$(CONFIG_PXA95x) += mfp-pxa3xx.o clock-pxa3xx.o pxa95x.o smemc.o
+obj-$(CONFIG_PXA95x) += mfp-pxa3xx.o clock-pxa3xx.o pxa3xx.o pxa95x.o smemc.o
obj-$(CONFIG_CPU_PXA300) += pxa300.o
obj-$(CONFIG_CPU_PXA320) += pxa320.o
obj-$(CONFIG_CPU_PXA930) += pxa930.o
diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index 7765d677adbb..fc0b8544e174 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -591,7 +591,7 @@ static void balloon3_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ct
BALLOON3_NAND_CONTROL_REG);
if (balloon3_ctl_set)
__raw_writel(balloon3_ctl_set,
- BALLOON3_NAND_CONTROL_REG |
+ BALLOON3_NAND_CONTROL_REG +
BALLOON3_FPGA_SETnCLR);
}
@@ -608,7 +608,7 @@ static void balloon3_nand_select_chip(struct mtd_info *mtd, int chip)
__raw_writew(
BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 |
BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3,
- BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR);
+ BALLOON3_NAND_CONTROL_REG + BALLOON3_FPGA_SETnCLR);
/* Deassert correct nCE line */
__raw_writew(BALLOON3_NAND_CONTROL_FLCE0 << chip,
@@ -626,7 +626,7 @@ static int balloon3_nand_probe(struct platform_device *pdev)
int ret;
__raw_writew(BALLOON3_NAND_CONTROL2_16BIT,
- BALLOON3_NAND_CONTROL2_REG | BALLOON3_FPGA_SETnCLR);
+ BALLOON3_NAND_CONTROL2_REG + BALLOON3_FPGA_SETnCLR);
ver = __raw_readw(BALLOON3_FPGA_VER);
if (ver < 0x4f08)
@@ -649,7 +649,7 @@ static int balloon3_nand_probe(struct platform_device *pdev)
BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 |
BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3 |
BALLOON3_NAND_CONTROL_FLWP,
- BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR);
+ BALLOON3_NAND_CONTROL_REG + BALLOON3_FPGA_SETnCLR);
return 0;
err2:
@@ -807,7 +807,7 @@ static void __init balloon3_init(void)
static struct map_desc balloon3_io_desc[] __initdata = {
{ /* CPLD/FPGA */
- .virtual = BALLOON3_FPGA_VIRT,
+ .virtual = (unsigned long)BALLOON3_FPGA_VIRT,
.pfn = __phys_to_pfn(BALLOON3_FPGA_PHYS),
.length = BALLOON3_FPGA_LENGTH,
.type = MT_DEVICE,
diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.c b/arch/arm/mach-pxa/cm-x2xx-pci.c
index 6bf479d9b5ac..ebd9259f5ac9 100644
--- a/arch/arm/mach-pxa/cm-x2xx-pci.c
+++ b/arch/arm/mach-pxa/cm-x2xx-pci.c
@@ -26,7 +26,7 @@
#include <asm/hardware/it8152.h>
-unsigned long it8152_base_address;
+void __iomem *it8152_base_address;
static int cmx2xx_it8152_irq_gpio;
static void cmx2xx_it8152_irq_demux(unsigned int irq, struct irq_desc *desc)
diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c
index 349896c53abd..f2e4190080cb 100644
--- a/arch/arm/mach-pxa/cm-x2xx.c
+++ b/arch/arm/mach-pxa/cm-x2xx.c
@@ -39,7 +39,7 @@ extern void cmx270_init(void);
#define CMX2XX_NR_IRQS (IRQ_BOARD_START + 40)
/* virtual addresses for statically mapped regions */
-#define CMX2XX_VIRT_BASE (0xe8000000)
+#define CMX2XX_VIRT_BASE (void __iomem *)(0xe8000000)
#define CMX2XX_IT8152_VIRT (CMX2XX_VIRT_BASE)
/* physical address if local-bus attached devices */
@@ -482,7 +482,7 @@ static void __init cmx2xx_init_irq(void)
/* Map PCI companion statically */
static struct map_desc cmx2xx_io_desc[] __initdata = {
[0] = { /* PCI bridge */
- .virtual = CMX2XX_IT8152_VIRT,
+ .virtual = (unsigned long)CMX2XX_IT8152_VIRT,
.pfn = __phys_to_pfn(PXA_CS4_PHYS),
.length = SZ_64M,
.type = MT_DEVICE
diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c
index d2da301619f0..3a7387f93c38 100644
--- a/arch/arm/mach-pxa/cm-x300.c
+++ b/arch/arm/mach-pxa/cm-x300.c
@@ -775,7 +775,6 @@ static struct gpio cm_x300_wi2wi_gpios[] __initdata = {
static void __init cm_x300_init_wi2wi(void)
{
- int bt_reset, wlan_en;
int err;
if (system_rev < 130) {
@@ -791,12 +790,11 @@ static void __init cm_x300_init_wi2wi(void)
}
udelay(10);
- gpio_set_value(bt_reset, 0);
+ gpio_set_value(cm_x300_wi2wi_gpios[1].gpio, 0);
udelay(10);
- gpio_set_value(bt_reset, 1);
+ gpio_set_value(cm_x300_wi2wi_gpios[1].gpio, 1);
- gpio_free(wlan_en);
- gpio_free(bt_reset);
+ gpio_free_array(ARRAY_AND_SIZE(cm_x300_wi2wi_gpios));
}
/* MFP */
diff --git a/arch/arm/mach-pxa/include/mach/addr-map.h b/arch/arm/mach-pxa/include/mach/addr-map.h
index f4c03659168c..bbf9df37ad4b 100644
--- a/arch/arm/mach-pxa/include/mach/addr-map.h
+++ b/arch/arm/mach-pxa/include/mach/addr-map.h
@@ -20,7 +20,7 @@
* Peripheral Bus
*/
#define PERIPH_PHYS 0x40000000
-#define PERIPH_VIRT 0xf2000000
+#define PERIPH_VIRT IOMEM(0xf2000000)
#define PERIPH_SIZE 0x02000000
/*
@@ -28,21 +28,21 @@
*/
#define PXA2XX_SMEMC_PHYS 0x48000000
#define PXA3XX_SMEMC_PHYS 0x4a000000
-#define SMEMC_VIRT 0xf6000000
+#define SMEMC_VIRT IOMEM(0xf6000000)
#define SMEMC_SIZE 0x00100000
/*
* Dynamic Memory Controller (only on PXA3xx)
*/
#define DMEMC_PHYS 0x48100000
-#define DMEMC_VIRT 0xf6100000
+#define DMEMC_VIRT IOMEM(0xf6100000)
#define DMEMC_SIZE 0x00100000
/*
* Internal Memory Controller (PXA27x and later)
*/
#define IMEMC_PHYS 0x58000000
-#define IMEMC_VIRT 0xfe000000
+#define IMEMC_VIRT IOMEM(0xfe000000)
#define IMEMC_SIZE 0x00100000
#endif /* __ASM_MACH_ADDR_MAP_H */
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h
index 7074e76146c9..6d7eab3d0867 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/include/mach/balloon3.h
@@ -23,7 +23,7 @@ enum balloon3_features {
};
#define BALLOON3_FPGA_PHYS PXA_CS4_PHYS
-#define BALLOON3_FPGA_VIRT (0xf1000000) /* as per balloon2 */
+#define BALLOON3_FPGA_VIRT IOMEM(0xf1000000) /* as per balloon2 */
#define BALLOON3_FPGA_LENGTH 0x01000000
#define BALLOON3_FPGA_SETnCLR (0x1000)
diff --git a/arch/arm/mach-pxa/include/mach/gpio-pxa.h b/arch/arm/mach-pxa/include/mach/gpio-pxa.h
index 41b4c93a96c2..576868f8b8c5 100644
--- a/arch/arm/mach-pxa/include/mach/gpio-pxa.h
+++ b/arch/arm/mach-pxa/include/mach/gpio-pxa.h
@@ -25,7 +25,7 @@
#define GPIO_REGS_VIRT io_p2v(0x40E00000)
#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
+#define GPIO_REG(x) (GPIO_REGS_VIRT + (x))
/* GPIO Pin Level Registers */
#define GPLR0 GPIO_REG(BANK_OFF(0) + 0x00)
diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h
index de63ca3016b4..8184669dde28 100644
--- a/arch/arm/mach-pxa/include/mach/hardware.h
+++ b/arch/arm/mach-pxa/include/mach/hardware.h
@@ -36,22 +36,23 @@
* Note that not all PXA2xx chips implement all those addresses, and the
* kernel only maps the minimum needed range of this mapping.
*/
-#define io_p2v(x) (0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1))
#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1))
+#define io_p2v(x) IOMEM(0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1))
#ifndef __ASSEMBLY__
-
-# define __REG(x) (*((volatile u32 *)io_p2v(x)))
+# define IOMEM(x) ((void __iomem *)(x))
+# define __REG(x) (*((volatile u32 __iomem *)io_p2v(x)))
/* With indexed regs we don't want to feed the index through io_p2v()
especially if it is a variable, otherwise horrible code will result. */
# define __REG2(x,y) \
- (*(volatile u32 *)((u32)&__REG(x) + (y)))
+ (*(volatile u32 __iomem*)((u32)&__REG(x) + (y)))
# define __PREG(x) (io_v2p((u32)&(x)))
#else
+# define IOMEM(x) x
# define __REG(x) io_p2v(x)
# define __PREG(x) io_v2p(x)
diff --git a/arch/arm/mach-pxa/include/mach/lpd270.h b/arch/arm/mach-pxa/include/mach/lpd270.h
index cd070092b6eb..4edc712a2de8 100644
--- a/arch/arm/mach-pxa/include/mach/lpd270.h
+++ b/arch/arm/mach-pxa/include/mach/lpd270.h
@@ -13,13 +13,13 @@
#define __ASM_ARCH_LPD270_H
#define LPD270_CPLD_PHYS PXA_CS2_PHYS
-#define LPD270_CPLD_VIRT 0xf0000000
+#define LPD270_CPLD_VIRT IOMEM(0xf0000000)
#define LPD270_CPLD_SIZE 0x00100000
#define LPD270_ETH_PHYS (PXA_CS2_PHYS + 0x01000000)
/* CPLD registers */
-#define LPD270_CPLD_REG(x) ((unsigned long)(LPD270_CPLD_VIRT + (x)))
+#define LPD270_CPLD_REG(x) (LPD270_CPLD_VIRT + (x))
#define LPD270_CONTROL LPD270_CPLD_REG(0x00)
#define LPD270_PERIPHERAL0 LPD270_CPLD_REG(0x04)
#define LPD270_PERIPHERAL1 LPD270_CPLD_REG(0x08)
diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h
index 297387ec3618..990d2bf2fb45 100644
--- a/arch/arm/mach-pxa/include/mach/mtd-xip.h
+++ b/arch/arm/mach-pxa/include/mach/mtd-xip.h
@@ -16,7 +16,6 @@
#define __ARCH_PXA_MTD_XIP_H__
#include <mach/regs-ost.h>
-#include <mach/regs-intc.h>
#define xip_irqpending() (ICIP & ICMR)
diff --git a/arch/arm/mach-pxa/include/mach/palm27x.h b/arch/arm/mach-pxa/include/mach/palm27x.h
index 0a5e5eadebf5..f80bbe246afe 100644
--- a/arch/arm/mach-pxa/include/mach/palm27x.h
+++ b/arch/arm/mach-pxa/include/mach/palm27x.h
@@ -34,7 +34,7 @@ extern struct pxafb_mode_info palm_320x320_new_lcd_mode;
extern void __init palm27x_lcd_init(int power,
struct pxafb_mode_info *mode);
#else
-static inline void palm27x_lcd_init(int power, struct pxafb_mode_info *mode) {}
+#define palm27x_lcd_init(power, mode) do {} while (0)
#endif
#if defined(CONFIG_USB_GADGET_PXA27X) || \
diff --git a/arch/arm/mach-pxa/include/mach/palmtx.h b/arch/arm/mach-pxa/include/mach/palmtx.h
index 10abc4f2e8e4..7074a6ed46c6 100644
--- a/arch/arm/mach-pxa/include/mach/palmtx.h
+++ b/arch/arm/mach-pxa/include/mach/palmtx.h
@@ -71,7 +71,7 @@
/* Various addresses */
#define PALMTX_PCMCIA_PHYS 0x28000000
-#define PALMTX_PCMCIA_VIRT 0xf0000000
+#define PALMTX_PCMCIA_VIRT IOMEM(0xf0000000)
#define PALMTX_PCMCIA_SIZE 0x100000
#define PALMTX_PHYS_RAM_START 0xa0000000
@@ -84,8 +84,8 @@
#define PALMTX_NAND_ALE_PHYS (PALMTX_PHYS_NAND_START | (1 << 24))
#define PALMTX_NAND_CLE_PHYS (PALMTX_PHYS_NAND_START | (1 << 25))
-#define PALMTX_NAND_ALE_VIRT 0xff100000
-#define PALMTX_NAND_CLE_VIRT 0xff200000
+#define PALMTX_NAND_ALE_VIRT IOMEM(0xff100000)
+#define PALMTX_NAND_CLE_VIRT IOMEM(0xff200000)
/* TOUCHSCREEN */
#define AC97_LINK_FRAME 21
diff --git a/arch/arm/mach-pxa/include/mach/pxa27x.h b/arch/arm/mach-pxa/include/mach/pxa27x.h
index b9b1bdc4bacc..7cff640582b8 100644
--- a/arch/arm/mach-pxa/include/mach/pxa27x.h
+++ b/arch/arm/mach-pxa/include/mach/pxa27x.h
@@ -1,6 +1,7 @@
#ifndef __MACH_PXA27x_H
#define __MACH_PXA27x_H
+#include <linux/suspend.h>
#include <mach/hardware.h>
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa27x.h>
@@ -21,6 +22,7 @@
extern void __init pxa27x_map_io(void);
extern void __init pxa27x_init_irq(void);
extern int __init pxa27x_set_pwrmode(unsigned int mode);
+extern void pxa27x_cpu_pm_enter(suspend_state_t state);
#define pxa27x_handle_irq ichp_handle_irq
diff --git a/arch/arm/mach-pxa/include/mach/pxa95x.h b/arch/arm/mach-pxa/include/mach/pxa95x.h
new file mode 100644
index 000000000000..cbb097c4cb1f
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/pxa95x.h
@@ -0,0 +1,7 @@
+#ifndef __MACH_PXA95X_H
+#define __MACH_PXA95X_H
+
+#include <mach/pxa3xx.h>
+#include <mach/mfp-pxa930.h>
+
+#endif /* __MACH_PXA95X_H */
diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h
index 01a45ac48114..486b4c519ae2 100644
--- a/arch/arm/mach-pxa/include/mach/pxafb.h
+++ b/arch/arm/mach-pxa/include/mach/pxafb.h
@@ -158,5 +158,18 @@ struct pxafb_mach_info {
void pxa_set_fb_info(struct device *, struct pxafb_mach_info *);
unsigned long pxafb_get_hsync_time(struct device *dev);
+#ifdef CONFIG_FB_PXA_SMARTPANEL
extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int);
extern int pxafb_smart_flush(struct fb_info *info);
+#else
+static inline int pxafb_smart_queue(struct fb_info *info,
+ uint16_t *cmds, int n)
+{
+ return 0;
+}
+
+static inline int pxafb_smart_flush(struct fb_info *info)
+{
+ return 0;
+}
+#endif
diff --git a/arch/arm/mach-pxa/include/mach/smemc.h b/arch/arm/mach-pxa/include/mach/smemc.h
index 654adc90c9a0..b7de471b273a 100644
--- a/arch/arm/mach-pxa/include/mach/smemc.h
+++ b/arch/arm/mach-pxa/include/mach/smemc.h
@@ -13,7 +13,7 @@
#define PXA2XX_SMEMC_BASE 0x48000000
#define PXA3XX_SMEMC_BASE 0x4a000000
-#define SMEMC_VIRT 0xf6000000
+#define SMEMC_VIRT IOMEM(0xf6000000)
#define MDCNFG (SMEMC_VIRT + 0x00) /* SDRAM Configuration Register 0 */
#define MDREFR (SMEMC_VIRT + 0x04) /* SDRAM Refresh Control Register */
diff --git a/arch/arm/mach-pxa/include/mach/zeus.h b/arch/arm/mach-pxa/include/mach/zeus.h
index 0641f31a56b7..56024f81d57e 100644
--- a/arch/arm/mach-pxa/include/mach/zeus.h
+++ b/arch/arm/mach-pxa/include/mach/zeus.h
@@ -68,7 +68,7 @@
* Be gentle, and remap that over 32kB...
*/
-#define ZEUS_CPLD (0xf0000000)
+#define ZEUS_CPLD IOMEM(0xf0000000)
#define ZEUS_CPLD_VERSION (ZEUS_CPLD + 0x0000)
#define ZEUS_CPLD_ISA_IRQ (ZEUS_CPLD + 0x1000)
#define ZEUS_CPLD_CONTROL (ZEUS_CPLD + 0x2000)
@@ -76,7 +76,7 @@
/* CPLD register bits */
#define ZEUS_CPLD_CONTROL_CF_RST 0x01
-#define ZEUS_PC104IO (0xf1000000)
+#define ZEUS_PC104IO IOMEM(0xf1000000)
#define ZEUS_SRAM_SIZE (256 * 1024)
diff --git a/arch/arm/mach-pxa/include/mach/zylonite.h b/arch/arm/mach-pxa/include/mach/zylonite.h
index ea24998b923c..ecca976f03d2 100644
--- a/arch/arm/mach-pxa/include/mach/zylonite.h
+++ b/arch/arm/mach-pxa/include/mach/zylonite.h
@@ -19,7 +19,7 @@ extern int wm9713_irq;
extern int lcd_id;
extern int lcd_orientation;
-#ifdef CONFIG_CPU_PXA300
+#ifdef CONFIG_MACH_ZYLONITE300
extern void zylonite_pxa300_init(void);
#else
static inline void zylonite_pxa300_init(void)
@@ -29,7 +29,7 @@ static inline void zylonite_pxa300_init(void)
}
#endif
-#ifdef CONFIG_CPU_PXA320
+#ifdef CONFIG_MACH_ZYLONITE320
extern void zylonite_pxa320_init(void);
#else
static inline void zylonite_pxa320_init(void)
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index 8d9200f92268..532c5d3a97d2 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -26,7 +26,7 @@
#include "generic.h"
-#define IRQ_BASE (void __iomem *)io_p2v(0x40d00000)
+#define IRQ_BASE io_p2v(0x40d00000)
#define ICIP (0x000)
#define ICMR (0x004)
@@ -64,7 +64,7 @@ static inline void __iomem *irq_base(int i)
0x40d00130,
};
- return (void __iomem *)io_p2v(phys_base[i]);
+ return io_p2v(phys_base[i]);
}
void pxa_mask_irq(struct irq_data *d)
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index 64540d908958..1dd530279e0b 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -479,7 +479,7 @@ static void __init lpd270_init(void)
static struct map_desc lpd270_io_desc[] __initdata = {
{
- .virtual = LPD270_CPLD_VIRT,
+ .virtual = (unsigned long)LPD270_CPLD_VIRT,
.pfn = __phys_to_pfn(LPD270_CPLD_PHYS),
.length = LPD270_CPLD_SIZE,
.type = MT_DEVICE,
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c
index 7346fbfa8101..94e9708b349d 100644
--- a/arch/arm/mach-pxa/palmtreo.c
+++ b/arch/arm/mach-pxa/palmtreo.c
@@ -423,6 +423,7 @@ static void __init palmphone_common_init(void)
palmtreo_leds_init();
}
+#ifdef CONFIG_MACH_TREO680
static void __init treo680_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
@@ -430,7 +431,9 @@ static void __init treo680_init(void)
palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, GPIO_NR_TREO680_SD_READONLY,
GPIO_NR_TREO680_SD_POWER, 0);
}
+#endif
+#ifdef CONFIG_MACH_CENTRO
static void __init centro_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(centro685_pin_config));
@@ -438,7 +441,9 @@ static void __init centro_init(void)
palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, -1,
GPIO_NR_CENTRO_SD_POWER, 1);
}
+#endif
+#ifdef CONFIG_MACH_TREO680
MACHINE_START(TREO680, "Palm Treo 680")
.atag_offset = 0x100,
.map_io = pxa27x_map_io,
@@ -448,7 +453,9 @@ MACHINE_START(TREO680, "Palm Treo 680")
.timer = &pxa_timer,
.init_machine = treo680_init,
MACHINE_END
+#endif
+#ifdef CONFIG_MACH_CENTRO
MACHINE_START(CENTRO, "Palm Centro 685")
.atag_offset = 0x100,
.map_io = pxa27x_map_io,
@@ -458,3 +465,4 @@ MACHINE_START(CENTRO, "Palm Centro 685")
.timer = &pxa_timer,
.init_machine = centro_init,
MACHINE_END
+#endif
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index 2b9e76fc2c90..4e3e45927e95 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -247,7 +247,7 @@ static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd,
unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
- unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+ char __iomem *nandaddr = this->IO_ADDR_W;
if (cmd == NAND_CMD_NONE)
return;
@@ -315,17 +315,17 @@ static inline void palmtx_nand_init(void) {}
******************************************************************************/
static struct map_desc palmtx_io_desc[] __initdata = {
{
- .virtual = PALMTX_PCMCIA_VIRT,
+ .virtual = (unsigned long)PALMTX_PCMCIA_VIRT,
.pfn = __phys_to_pfn(PALMTX_PCMCIA_PHYS),
.length = PALMTX_PCMCIA_SIZE,
.type = MT_DEVICE,
}, {
- .virtual = PALMTX_NAND_ALE_VIRT,
+ .virtual = (unsigned long)PALMTX_NAND_ALE_VIRT,
.pfn = __phys_to_pfn(PALMTX_NAND_ALE_PHYS),
.length = SZ_1M,
.type = MT_DEVICE,
}, {
- .virtual = PALMTX_NAND_CLE_VIRT,
+ .virtual = (unsigned long)PALMTX_NAND_CLE_VIRT,
.pfn = __phys_to_pfn(PALMTX_NAND_CLE_PHYS),
.length = SZ_1M,
.type = MT_DEVICE,
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index 8746e1090b6e..f05f9486b0cb 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -325,7 +325,7 @@ void __init pxa26x_init_irq(void)
static struct map_desc pxa25x_io_desc[] __initdata = {
{ /* Mem Ctl */
- .virtual = SMEMC_VIRT,
+ .virtual = (unsigned long)SMEMC_VIRT,
.pfn = __phys_to_pfn(PXA2XX_SMEMC_BASE),
.length = 0x00200000,
.type = MT_DEVICE
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index 2bb5cf8ba6ec..bc5a98ebaa72 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -391,7 +391,7 @@ void __init pxa27x_init_irq(void)
static struct map_desc pxa27x_io_desc[] __initdata = {
{ /* Mem Ctl */
- .virtual = SMEMC_VIRT,
+ .virtual = (unsigned long)SMEMC_VIRT,
.pfn = __phys_to_pfn(PXA2XX_SMEMC_BASE),
.length = 0x00200000,
.type = MT_DEVICE
diff --git a/arch/arm/mach-pxa/pxa3xx-ulpi.c b/arch/arm/mach-pxa/pxa3xx-ulpi.c
index ce7168b233e2..e28dfb88827f 100644
--- a/arch/arm/mach-pxa/pxa3xx-ulpi.c
+++ b/arch/arm/mach-pxa/pxa3xx-ulpi.c
@@ -265,6 +265,7 @@ int pxa3xx_u2d_start_hc(struct usb_bus *host)
return err;
}
+EXPORT_SYMBOL_GPL(pxa3xx_u2d_start_hc);
void pxa3xx_u2d_stop_hc(struct usb_bus *host)
{
@@ -277,6 +278,7 @@ void pxa3xx_u2d_stop_hc(struct usb_bus *host)
clk_disable(u2d->clk);
}
+EXPORT_SYMBOL_GPL(pxa3xx_u2d_stop_hc);
static int pxa3xx_u2d_probe(struct platform_device *pdev)
{
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
index f940a1345531..0737c59b88ae 100644
--- a/arch/arm/mach-pxa/pxa3xx.c
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -393,7 +393,7 @@ void __init pxa3xx_init_irq(void)
static struct map_desc pxa3xx_io_desc[] __initdata = {
{ /* Mem Ctl */
- .virtual = SMEMC_VIRT,
+ .virtual = (unsigned long)SMEMC_VIRT,
.pfn = __phys_to_pfn(PXA3XX_SMEMC_BASE),
.length = 0x00200000,
.type = MT_DEVICE
diff --git a/arch/arm/mach-pxa/saarb.c b/arch/arm/mach-pxa/saarb.c
index 3c988b6f718f..3e999e308a2d 100644
--- a/arch/arm/mach-pxa/saarb.c
+++ b/arch/arm/mach-pxa/saarb.c
@@ -24,6 +24,7 @@
#include <mach/hardware.h>
#include <mach/mfp.h>
#include <mach/mfp-pxa930.h>
+#include <mach/pxa95x.h>
#include "generic.h"
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index 84ed72de53b5..ead32c90fec1 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -686,7 +686,8 @@ static void z2_power_off(void)
*/
PSPR = 0x0;
local_irq_disable();
- pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PHYS_OFFSET - PAGE_OFFSET);
+ pxa27x_set_pwrmode(PWRMODE_DEEPSLEEP);
+ pxa27x_cpu_pm_enter(PM_SUSPEND_MEM);
}
#else
#define z2_power_off NULL
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index c424e7d85ce3..498b83b089f3 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -860,25 +860,25 @@ static void __init zeus_init(void)
static struct map_desc zeus_io_desc[] __initdata = {
{
- .virtual = ZEUS_CPLD_VERSION,
+ .virtual = (unsigned long)ZEUS_CPLD_VERSION,
.pfn = __phys_to_pfn(ZEUS_CPLD_VERSION_PHYS),
.length = 0x1000,
.type = MT_DEVICE,
},
{
- .virtual = ZEUS_CPLD_ISA_IRQ,
+ .virtual = (unsigned long)ZEUS_CPLD_ISA_IRQ,
.pfn = __phys_to_pfn(ZEUS_CPLD_ISA_IRQ_PHYS),
.length = 0x1000,
.type = MT_DEVICE,
},
{
- .virtual = ZEUS_CPLD_CONTROL,
+ .virtual = (unsigned long)ZEUS_CPLD_CONTROL,
.pfn = __phys_to_pfn(ZEUS_CPLD_CONTROL_PHYS),
.length = 0x1000,
.type = MT_DEVICE,
},
{
- .virtual = ZEUS_PC104IO,
+ .virtual = (unsigned long)ZEUS_PC104IO,
.pfn = __phys_to_pfn(ZEUS_PC104IO_PHYS),
.length = 0x00800000,
.type = MT_DEVICE,
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
index 1da23bb87c16..8aa104a4711a 100644
--- a/arch/arm/mach-ux500/cpu.c
+++ b/arch/arm/mach-ux500/cpu.c
@@ -99,7 +99,27 @@ static void ux500_l2x0_inv_all(void)
ux500_cache_sync();
}
-static int ux500_l2x0_init(void)
+static int __init ux500_l2x0_unlock(void)
+{
+ int i;
+
+ /*
+ * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
+ * apparently locks both caches before jumping to the kernel. The
+ * l2x0 core will not touch the unlock registers if the l2x0 is
+ * already enabled, so we do it right here instead. The PL310 has
+ * 8 sets of registers, one per possible CPU.
+ */
+ for (i = 0; i < 8; i++) {
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ }
+ return 0;
+}
+
+static int __init ux500_l2x0_init(void)
{
if (cpu_is_u5500())
l2x0_base = __io_address(U5500_L2CC_BASE);
@@ -108,6 +128,9 @@ static int ux500_l2x0_init(void)
else
ux500_unknown_soc();
+ /* Unlock before init */
+ ux500_l2x0_unlock();
+
/* 64KB way size, 8 way associativity, force WA */
l2x0_init(l2x0_base, 0x3e060000, 0xc0000fff);
diff --git a/arch/arm/plat-mxc/include/mach/iomux-v3.h b/arch/arm/plat-mxc/include/mach/iomux-v3.h
index ebbce33097a7..45099566fecc 100644
--- a/arch/arm/plat-mxc/include/mach/iomux-v3.h
+++ b/arch/arm/plat-mxc/include/mach/iomux-v3.h
@@ -89,11 +89,11 @@ typedef u64 iomux_v3_cfg_t;
#define PAD_CTL_HYS (1 << 8)
#define PAD_CTL_PKE (1 << 7)
-#define PAD_CTL_PUE (1 << 6)
-#define PAD_CTL_PUS_100K_DOWN (0 << 4)
-#define PAD_CTL_PUS_47K_UP (1 << 4)
-#define PAD_CTL_PUS_100K_UP (2 << 4)
-#define PAD_CTL_PUS_22K_UP (3 << 4)
+#define PAD_CTL_PUE (1 << 6 | PAD_CTL_PKE)
+#define PAD_CTL_PUS_100K_DOWN (0 << 4 | PAD_CTL_PUE)
+#define PAD_CTL_PUS_47K_UP (1 << 4 | PAD_CTL_PUE)
+#define PAD_CTL_PUS_100K_UP (2 << 4 | PAD_CTL_PUE)
+#define PAD_CTL_PUS_22K_UP (3 << 4 | PAD_CTL_PUE)
#define PAD_CTL_ODE (1 << 3)
diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h
index 89e68e07b0a8..5c79c29f2833 100644
--- a/arch/arm/plat-pxa/include/plat/mfp.h
+++ b/arch/arm/plat-pxa/include/plat/mfp.h
@@ -456,7 +456,7 @@ struct mfp_addr_map {
#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
-void __init mfp_init_base(unsigned long mfpr_base);
+void __init mfp_init_base(void __iomem *mfpr_base);
void __init mfp_init_addr(struct mfp_addr_map *map);
/*
diff --git a/arch/arm/plat-pxa/mfp.c b/arch/arm/plat-pxa/mfp.c
index be12eadcce20..2c4dbb1f4236 100644
--- a/arch/arm/plat-pxa/mfp.c
+++ b/arch/arm/plat-pxa/mfp.c
@@ -229,7 +229,7 @@ void mfp_write(int mfp, unsigned long val)
spin_unlock_irqrestore(&mfp_spin_lock, flags);
}
-void __init mfp_init_base(unsigned long mfpr_base)
+void __init mfp_init_base(void __iomem *mfpr_base)
{
int i;
@@ -237,7 +237,7 @@ void __init mfp_init_base(unsigned long mfpr_base)
for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
mfp_table[i].config = -1;
- mfpr_mmio_base = (void __iomem *)mfpr_base;
+ mfpr_mmio_base = mfpr_base;
}
void __init mfp_init_addr(struct mfp_addr_map *map)
diff --git a/drivers/gpio/gpio-pxa.c b/drivers/gpio/gpio-pxa.c
index 9052925c6fa2..ee137712f9db 100644
--- a/drivers/gpio/gpio-pxa.c
+++ b/drivers/gpio/gpio-pxa.c
@@ -122,7 +122,7 @@ static int __init pxa_init_gpio_chip(int gpio_end)
struct gpio_chip *c = &chips[i].chip;
sprintf(chips[i].label, "gpio-%d", i);
- chips[i].regbase = (void __iomem *)GPIO_BANK(i);
+ chips[i].regbase = GPIO_BANK(i);
c->base = gpio;
c->label = chips[i].label;
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 50d5f27f09d0..d593878d66d0 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -63,7 +63,7 @@ config AD525X_DPOT_SPI
config ATMEL_PWM
tristate "Atmel AT32/AT91 PWM support"
- depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
+ depends on HAVE_CLK
help
This option enables device driver support for the PWM channels
on certain Atmel processors. Pulse Width Modulation is used for
diff --git a/drivers/pcmcia/pxa2xx_balloon3.c b/drivers/pcmcia/pxa2xx_balloon3.c
index f56d7de7c751..22a75e610f12 100644
--- a/drivers/pcmcia/pxa2xx_balloon3.c
+++ b/drivers/pcmcia/pxa2xx_balloon3.c
@@ -97,7 +97,7 @@ static void balloon3_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
static int balloon3_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
const socket_state_t *state)
{
- __raw_writew(BALLOON3_CF_RESET, BALLOON3_CF_CONTROL_REG |
+ __raw_writew(BALLOON3_CF_RESET, BALLOON3_CF_CONTROL_REG +
((state->flags & SS_RESET) ?
BALLOON3_FPGA_SETnCLR : 0));
return 0;
diff --git a/drivers/video/mbx/mbxfb.c b/drivers/video/mbx/mbxfb.c
index afea9abbd678..6ce34160da78 100644
--- a/drivers/video/mbx/mbxfb.c
+++ b/drivers/video/mbx/mbxfb.c
@@ -34,7 +34,7 @@
#include "regs.h"
#include "reg_bits.h"
-static unsigned long virt_base_2700;
+static void __iomem *virt_base_2700;
#define write_reg(val, reg) do { writel((val), (reg)); } while(0)
@@ -850,7 +850,7 @@ static int mbxfb_suspend(struct platform_device *dev, pm_message_t state)
{
/* make frame buffer memory enter self-refresh mode */
write_reg_dly(LMPWR_MC_PWR_SRM, LMPWR);
- while (LMPWRSTAT != LMPWRSTAT_MC_PWR_SRM)
+ while (readl(LMPWRSTAT) != LMPWRSTAT_MC_PWR_SRM)
; /* empty statement */
/* reset the device, since it's initial state is 'mostly sleeping' */
@@ -946,7 +946,7 @@ static int __devinit mbxfb_probe(struct platform_device *dev)
ret = -EINVAL;
goto err3;
}
- virt_base_2700 = (unsigned long)mfbi->reg_virt_addr;
+ virt_base_2700 = mfbi->reg_virt_addr;
mfbi->fb_virt_addr = ioremap_nocache(mfbi->fb_phys_addr,
res_size(mfbi->fb_req));
diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c
index e89778f4081f..1d1e4f175e78 100644
--- a/drivers/video/pxafb.c
+++ b/drivers/video/pxafb.c
@@ -1309,16 +1309,6 @@ static int pxafb_smart_init(struct pxafb_info *fbi)
return 0;
}
#else
-int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int n_cmds)
-{
- return 0;
-}
-
-int pxafb_smart_flush(struct fb_info *info)
-{
- return 0;
-}
-
static inline int pxafb_smart_init(struct pxafb_info *fbi) { return 0; }
#endif /* CONFIG_FB_PXA_SMARTPANEL */