diff options
118 files changed, 4529 insertions, 1358 deletions
diff --git a/Documentation/arm/Samsung-S3C24XX/GPIO.txt b/Documentation/arm/Samsung-S3C24XX/GPIO.txt index ea7ccfc4b274..948c8718d967 100644 --- a/Documentation/arm/Samsung-S3C24XX/GPIO.txt +++ b/Documentation/arm/Samsung-S3C24XX/GPIO.txt @@ -51,7 +51,7 @@ PIN Numbers ----------- Each pin has an unique number associated with it in regs-gpio.h, - eg S3C2410_GPA0 or S3C2410_GPF1. These defines are used to tell + eg S3C2410_GPA(0) or S3C2410_GPF(1). These defines are used to tell the GPIO functions which pin is to be used. @@ -65,11 +65,11 @@ Configuring a pin Eg: - s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0); - s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1); + s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0); + s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1); - which would turn GPA0 into the lowest Address line A0, and set - GPE8 to be connected to the SDIO/MMC controller's SDDAT1 line. + which would turn GPA(0) into the lowest Address line A0, and set + GPE(8) to be connected to the SDIO/MMC controller's SDDAT1 line. Reading the current configuration diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig index a2cd9beaf37d..38518d450bc0 100644 --- a/arch/arm/common/Kconfig +++ b/arch/arm/common/Kconfig @@ -4,6 +4,13 @@ config ARM_GIC config ARM_VIC bool +config ARM_VIC_NR + int + default 2 + help + The maximum number of VICs available in the system, for + power management. + config ICST525 bool diff --git a/arch/arm/common/vic.c b/arch/arm/common/vic.c index b2a781d9ce05..887c6eb3a18a 100644 --- a/arch/arm/common/vic.c +++ b/arch/arm/common/vic.c @@ -21,6 +21,7 @@ #include <linux/init.h> #include <linux/list.h> #include <linux/io.h> +#include <linux/sysdev.h> #include <asm/mach/irq.h> #include <asm/hardware/vic.h> @@ -39,11 +40,219 @@ static void vic_unmask_irq(unsigned int irq) writel(1 << irq, base + VIC_INT_ENABLE); } +/** + * vic_init2 - common initialisation code + * @base: Base of the VIC. + * + * Common initialisation code for registeration + * and resume. +*/ +static void vic_init2(void __iomem *base) +{ + int i; + + for (i = 0; i < 16; i++) { + void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4); + writel(VIC_VECT_CNTL_ENABLE | i, reg); + } + + writel(32, base + VIC_PL190_DEF_VECT_ADDR); +} + +#if defined(CONFIG_PM) +/** + * struct vic_device - VIC PM device + * @sysdev: The system device which is registered. + * @irq: The IRQ number for the base of the VIC. + * @base: The register base for the VIC. + * @resume_sources: A bitmask of interrupts for resume. + * @resume_irqs: The IRQs enabled for resume. + * @int_select: Save for VIC_INT_SELECT. + * @int_enable: Save for VIC_INT_ENABLE. + * @soft_int: Save for VIC_INT_SOFT. + * @protect: Save for VIC_PROTECT. + */ +struct vic_device { + struct sys_device sysdev; + + void __iomem *base; + int irq; + u32 resume_sources; + u32 resume_irqs; + u32 int_select; + u32 int_enable; + u32 soft_int; + u32 protect; +}; + +/* we cannot allocate memory when VICs are initially registered */ +static struct vic_device vic_devices[CONFIG_ARM_VIC_NR]; + +static inline struct vic_device *to_vic(struct sys_device *sys) +{ + return container_of(sys, struct vic_device, sysdev); +} + +static int vic_id; + +static int vic_class_resume(struct sys_device *dev) +{ + struct vic_device *vic = to_vic(dev); + void __iomem *base = vic->base; + + printk(KERN_DEBUG "%s: resuming vic at %p\n", __func__, base); + + /* re-initialise static settings */ + vic_init2(base); + + writel(vic->int_select, base + VIC_INT_SELECT); + writel(vic->protect, base + VIC_PROTECT); + + /* set the enabled ints and then clear the non-enabled */ + writel(vic->int_enable, base + VIC_INT_ENABLE); + writel(~vic->int_enable, base + VIC_INT_ENABLE_CLEAR); + + /* and the same for the soft-int register */ + + writel(vic->soft_int, base + VIC_INT_SOFT); + writel(~vic->soft_int, base + VIC_INT_SOFT_CLEAR); + + return 0; +} + +static int vic_class_suspend(struct sys_device *dev, pm_message_t state) +{ + struct vic_device *vic = to_vic(dev); + void __iomem *base = vic->base; + + printk(KERN_DEBUG "%s: suspending vic at %p\n", __func__, base); + + vic->int_select = readl(base + VIC_INT_SELECT); + vic->int_enable = readl(base + VIC_INT_ENABLE); + vic->soft_int = readl(base + VIC_INT_SOFT); + vic->protect = readl(base + VIC_PROTECT); + + /* set the interrupts (if any) that are used for + * resuming the system */ + + writel(vic->resume_irqs, base + VIC_INT_ENABLE); + writel(~vic->resume_irqs, base + VIC_INT_ENABLE_CLEAR); + + return 0; +} + +struct sysdev_class vic_class = { + .name = "vic", + .suspend = vic_class_suspend, + .resume = vic_class_resume, +}; + +/** + * vic_pm_register - Register a VIC for later power management control + * @base: The base address of the VIC. + * @irq: The base IRQ for the VIC. + * @resume_sources: bitmask of interrupts allowed for resume sources. + * + * Register the VIC with the system device tree so that it can be notified + * of suspend and resume requests and ensure that the correct actions are + * taken to re-instate the settings on resume. + */ +static void __init vic_pm_register(void __iomem *base, unsigned int irq, u32 resume_sources) +{ + struct vic_device *v; + + if (vic_id >= ARRAY_SIZE(vic_devices)) + printk(KERN_ERR "%s: too few VICs, increase CONFIG_ARM_VIC_NR\n", __func__); + else { + v = &vic_devices[vic_id]; + v->base = base; + v->resume_sources = resume_sources; + v->irq = irq; + vic_id++; + } +} + +/** + * vic_pm_init - initicall to register VIC pm + * + * This is called via late_initcall() to register + * the resources for the VICs due to the early + * nature of the VIC's registration. +*/ +static int __init vic_pm_init(void) +{ + struct vic_device *dev = vic_devices; + int err; + int id; + + if (vic_id == 0) + return 0; + + err = sysdev_class_register(&vic_class); + if (err) { + printk(KERN_ERR "%s: cannot register class\n", __func__); + return err; + } + + for (id = 0; id < vic_id; id++, dev++) { + dev->sysdev.id = id; + dev->sysdev.cls = &vic_class; + + err = sysdev_register(&dev->sysdev); + if (err) { + printk(KERN_ERR "%s: failed to register device\n", + __func__); + return err; + } + } + + return 0; +} + +late_initcall(vic_pm_init); + +static struct vic_device *vic_from_irq(unsigned int irq) +{ + struct vic_device *v = vic_devices; + unsigned int base_irq = irq & ~31; + int id; + + for (id = 0; id < vic_id; id++, v++) { + if (v->irq == base_irq) + return v; + } + + return NULL; +} + +static int vic_set_wake(unsigned int irq, unsigned int on) +{ + struct vic_device *v = vic_from_irq(irq); + unsigned int off = irq & 31; + + if (!v) + return -EINVAL; + + if (on) + v->resume_irqs |= 1 << off; + else + v->resume_irqs &= ~(1 << off); + + return 0; +} + +#else +static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg1) { } + +#define vic_set_wake NULL +#endif /* CONFIG_PM */ + static struct irq_chip vic_chip = { .name = "VIC", .ack = vic_mask_irq, .mask = vic_mask_irq, .unmask = vic_unmask_irq, + .set_wake = vic_set_wake, }; /** @@ -51,9 +260,10 @@ static struct irq_chip vic_chip = { * @base: iomem base address * @irq_start: starting interrupt number, must be muliple of 32 * @vic_sources: bitmask of interrupt sources to allow + * @resume_sources: bitmask of interrupt sources to allow for resume */ void __init vic_init(void __iomem *base, unsigned int irq_start, - u32 vic_sources) + u32 vic_sources, u32 resume_sources) { unsigned int i; @@ -77,12 +287,7 @@ void __init vic_init(void __iomem *base, unsigned int irq_start, writel(value, base + VIC_PL190_VECT_ADDR); } - for (i = 0; i < 16; i++) { - void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4); - writel(VIC_VECT_CNTL_ENABLE | i, reg); - } - - writel(32, base + VIC_PL190_DEF_VECT_ADDR); + vic_init2(base); for (i = 0; i < 32; i++) { if (vic_sources & (1 << i)) { @@ -94,4 +299,6 @@ void __init vic_init(void __iomem *base, unsigned int irq_start, set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); } } + + vic_pm_register(base, irq_start, resume_sources); } diff --git a/arch/arm/include/asm/hardware/pl080.h b/arch/arm/include/asm/hardware/pl080.h new file mode 100644 index 000000000000..6a6c66be7f65 --- /dev/null +++ b/arch/arm/include/asm/hardware/pl080.h @@ -0,0 +1,138 @@ +/* arch/arm/include/asm/hardware/pl080.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * ARM PrimeCell PL080 DMA controller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* Note, there are some Samsung updates to this controller block which + * make it not entierly compatible with the PL080 specification from + * ARM. When in doubt, check the Samsung documentation first. + * + * The Samsung defines are PL080S, and add an extra controll register, + * the ability to move more than 2^11 counts of data and some extra + * OneNAND features. +*/ + +#define PL080_INT_STATUS (0x00) +#define PL080_TC_STATUS (0x04) +#define PL080_TC_CLEAR (0x08) +#define PL080_ERR_STATUS (0x0C) +#define PL080_ERR_CLEAR (0x10) +#define PL080_RAW_TC_STATUS (0x14) +#define PL080_RAW_ERR_STATUS (0x18) +#define PL080_EN_CHAN (0x1c) +#define PL080_SOFT_BREQ (0x20) +#define PL080_SOFT_SREQ (0x24) +#define PL080_SOFT_LBREQ (0x28) +#define PL080_SOFT_LSREQ (0x2C) + +#define PL080_CONFIG (0x30) +#define PL080_CONFIG_M2_BE (1 << 2) +#define PL080_CONFIG_M1_BE (1 << 1) +#define PL080_CONFIG_ENABLE (1 << 0) + +#define PL080_SYNC (0x34) + +/* Per channel configuration registers */ + +#define PL008_Cx_STRIDE (0x20) +#define PL080_Cx_BASE(x) ((0x100 + (x * 0x20))) +#define PL080_Cx_SRC_ADDR(x) ((0x100 + (x * 0x20))) +#define PL080_Cx_DST_ADDR(x) ((0x104 + (x * 0x20))) +#define PL080_Cx_LLI(x) ((0x108 + (x * 0x20))) +#define PL080_Cx_CONTROL(x) ((0x10C + (x * 0x20))) +#define PL080_Cx_CONFIG(x) ((0x110 + (x * 0x20))) +#define PL080S_Cx_CONTROL2(x) ((0x110 + (x * 0x20))) +#define PL080S_Cx_CONFIG(x) ((0x114 + (x * 0x20))) + +#define PL080_CH_SRC_ADDR (0x00) +#define PL080_CH_DST_ADDR (0x04) +#define PL080_CH_LLI (0x08) +#define PL080_CH_CONTROL (0x0C) +#define PL080_CH_CONFIG (0x10) +#define PL080S_CH_CONTROL2 (0x10) +#define PL080S_CH_CONFIG (0x14) + +#define PL080_LLI_ADDR_MASK (0x3fffffff << 2) +#define PL080_LLI_ADDR_SHIFT (2) +#define PL080_LLI_LM_AHB2 (1 << 0) + +#define PL080_CONTROL_TC_IRQ_EN (1 << 31) +#define PL080_CONTROL_PROT_MASK (0x7 << 28) +#define PL080_CONTROL_PROT_SHIFT (28) +#define PL080_CONTROL_PROT_SYS (1 << 28) +#define PL080_CONTROL_DST_INCR (1 << 27) +#define PL080_CONTROL_SRC_INCR (1 << 26) +#define PL080_CONTROL_DST_AHB2 (1 << 25) +#define PL080_CONTROL_SRC_AHB2 (1 << 24) +#define PL080_CONTROL_DWIDTH_MASK (0x7 << 21) +#define PL080_CONTROL_DWIDTH_SHIFT (21) +#define PL080_CONTROL_SWIDTH_MASK (0x7 << 18) +#define PL080_CONTROL_SWIDTH_SHIFT (18) +#define PL080_CONTROL_DB_SIZE_MASK (0x7 << 15) +#define PL080_CONTROL_DB_SIZE_SHIFT (15) +#define PL080_CONTROL_SB_SIZE_MASK (0x7 << 12) +#define PL080_CONTROL_SB_SIZE_SHIFT (12) +#define PL080_CONTROL_TRANSFER_SIZE_MASK (0xfff << 0) +#define PL080_CONTROL_TRANSFER_SIZE_SHIFT (0) + +#define PL080_BSIZE_1 (0x0) +#define PL080_BSIZE_4 (0x1) +#define PL080_BSIZE_8 (0x2) +#define PL080_BSIZE_16 (0x3) +#define PL080_BSIZE_32 (0x4) +#define PL080_BSIZE_64 (0x5) +#define PL080_BSIZE_128 (0x6) +#define PL080_BSIZE_256 (0x7) + +#define PL080_WIDTH_8BIT (0x0) +#define PL080_WIDTH_16BIT (0x1) +#define PL080_WIDTH_32BIT (0x2) + +#define PL080_CONFIG_HALT (1 << 18) +#define PL080_CONFIG_ACTIVE (1 << 17) /* RO */ +#define PL080_CONFIG_LOCK (1 << 16) +#define PL080_CONFIG_TC_IRQ_MASK (1 << 15) +#define PL080_CONFIG_ERR_IRQ_MASK (1 << 14) +#define PL080_CONFIG_FLOW_CONTROL_MASK (0x7 << 11) +#define PL080_CONFIG_FLOW_CONTROL_SHIFT (11) +#define PL080_CONFIG_DST_SEL_MASK (0xf << 6) +#define PL080_CONFIG_DST_SEL_SHIFT (6) +#define PL080_CONFIG_SRC_SEL_MASK (0xf << 1) +#define PL080_CONFIG_SRC_SEL_SHIFT (1) +#define PL080_CONFIG_ENABLE (1 << 0) + +#define PL080_FLOW_MEM2MEM (0x0) +#define PL080_FLOW_MEM2PER (0x1) +#define PL080_FLOW_PER2MEM (0x2) +#define PL080_FLOW_SRC2DST (0x3) +#define PL080_FLOW_SRC2DST_DST (0x4) +#define PL080_FLOW_MEM2PER_PER (0x5) +#define PL080_FLOW_PER2MEM_PER (0x6) +#define PL080_FLOW_SRC2DST_SRC (0x7) + +/* DMA linked list chain structure */ + +struct pl080_lli { + u32 src_addr; + u32 dst_addr; + u32 next_lli; + u32 control0; +}; + +struct pl080s_lli { + u32 src_addr; + u32 dst_addr; + u32 next_lli; + u32 control0; + u32 control1; +}; + diff --git a/arch/arm/include/asm/hardware/vic.h b/arch/arm/include/asm/hardware/vic.h index f87328d4a180..5d72550a8097 100644 --- a/arch/arm/include/asm/hardware/vic.h +++ b/arch/arm/include/asm/hardware/vic.h @@ -41,7 +41,7 @@ #define VIC_PL192_VECT_ADDR 0xF00 #ifndef __ASSEMBLY__ -void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources); +void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources, u32 resume_sources); #endif #endif diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index f477df0e5e4c..204dc5cbd0b8 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -362,8 +362,8 @@ void __init ep93xx_init_irq(void) { int gpio_irq; - vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK); - vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK); + vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0); + vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0); for (gpio_irq = gpio_to_irq(0); gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) { diff --git a/arch/arm/mach-netx/generic.c b/arch/arm/mach-netx/generic.c index 79df60c20e70..43da8bb4926b 100644 --- a/arch/arm/mach-netx/generic.c +++ b/arch/arm/mach-netx/generic.c @@ -168,7 +168,7 @@ void __init netx_init_irq(void) { int irq; - vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0); + vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0, 0); for (irq = NETX_IRQ_HIF_CHAINED(0); irq <= NETX_IRQ_HIF_LAST; irq++) { set_irq_chip(irq, &netx_hif_chip); diff --git a/arch/arm/mach-s3c2400/gpio.c b/arch/arm/mach-s3c2400/gpio.c index 7a7ed4174c8c..6c68e78f3595 100644 --- a/arch/arm/mach-s3c2400/gpio.c +++ b/arch/arm/mach-s3c2400/gpio.c @@ -33,10 +33,10 @@ int s3c2400_gpio_getirq(unsigned int pin) { - if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7) - return -1; /* not valid interrupts */ + if (pin < S3C2410_GPE(0) || pin > S3C2400_GPE(7)) + return -EINVAL; /* not valid interrupts */ - return (pin - S3C2410_GPE0) + IRQ_EINT0; + return (pin - S3C2410_GPE(0)) + IRQ_EINT0; } EXPORT_SYMBOL(s3c2400_gpio_getirq); diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 63a30d1dd425..41bb65d5b91f 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -59,6 +59,7 @@ config ARCH_H1940 bool "IPAQ H1940" select CPU_S3C2410 select PM_H1940 if PM + select S3C_DEV_USB_HOST help Say Y here if you are using the HP IPAQ H1940 @@ -70,6 +71,7 @@ config PM_H1940 config MACH_N30 bool "Acer N30 family" select CPU_S3C2410 + select S3C_DEV_USB_HOST help Say Y here if you want suppt for the Acer N30, Acer N35, Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs. @@ -82,6 +84,7 @@ config ARCH_BAST select MACH_BAST_IDE select S3C24XX_DCLK select ISA + select S3C_DEV_USB_HOST help Say Y here if you are using the Simtec Electronics EB2410ITX development board (also known as BAST) @@ -89,6 +92,7 @@ config ARCH_BAST config MACH_OTOM bool "NexVision OTOM Board" select CPU_S3C2410 + select S3C_DEV_USB_HOST help Say Y here if you are using the Nex Vision OTOM board @@ -96,6 +100,7 @@ config MACH_AML_M5900 bool "AML M5900 Series" select CPU_S3C2410 select PM_SIMTEC if PM + select S3C_DEV_USB_HOST help Say Y here if you are using the American Microsystems M5900 Series <http://www.amltd.com> @@ -111,6 +116,7 @@ config BAST_PC104_IRQ config MACH_TCT_HAMMER bool "TCT Hammer Board" select CPU_S3C2410 + select S3C_DEV_USB_HOST help Say Y here if you are using the TinCanTools Hammer Board <http://www.tincantools.com> @@ -122,12 +128,14 @@ config MACH_VR1000 select SIMTEC_NOR select MACH_BAST_IDE select CPU_S3C2410 + select S3C_DEV_USB_HOST help Say Y here if you are using the Thorcom VR1000 board. config MACH_QT2410 bool "QT2410" select CPU_S3C2410 + select S3C_DEV_USB_HOST help Say Y here if you are using the Armzone QT2410 diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c index 440c014e24b3..dbf96e60d992 100644 --- a/arch/arm/mach-s3c2410/dma.c +++ b/arch/arm/mach-s3c2410/dma.c @@ -17,14 +17,16 @@ #include <linux/sysdev.h> #include <linux/serial_core.h> +#include <mach/map.h> #include <mach/dma.h> #include <plat/cpu.h> -#include <plat/dma.h> +#include <plat/dma-plat.h> #include <plat/regs-serial.h> #include <mach/regs-gpio.h> #include <plat/regs-ac97.h> +#include <plat/regs-dma.h> #include <mach/regs-mem.h> #include <mach/regs-lcd.h> #include <mach/regs-sdi.h> diff --git a/arch/arm/mach-s3c2410/gpio.c b/arch/arm/mach-s3c2410/gpio.c index 36a3132f39e7..7974afca297c 100644 --- a/arch/arm/mach-s3c2410/gpio.c +++ b/arch/arm/mach-s3c2410/gpio.c @@ -39,12 +39,12 @@ int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, unsigned long flags; unsigned long val; - if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15) - return -1; + if (pin < S3C2410_GPG(8) || pin > S3C2410_GPG(15)) + return -EINVAL; config &= 0xff; - pin -= S3C2410_GPG8; + pin -= S3C2410_GPG(8); reg += pin & ~3; local_irq_save(flags); diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c index 5a6bc56f186b..5aabf117cbb0 100644 --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -16,6 +16,8 @@ #include <linux/string.h> #include <linux/ctype.h> #include <linux/leds.h> +#include <linux/gpio.h> + #include <mach/regs-gpio.h> #include <mach/hardware.h> #include <mach/h1940-latch.h> @@ -41,9 +43,9 @@ static void h1940bt_enable(int on) h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); /* Reset the chip */ mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); state = 1; } @@ -52,9 +54,9 @@ static void h1940bt_enable(int on) led_trigger_event(bt_led_trigger, 0); #endif - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); mdelay(10); h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); @@ -87,14 +89,14 @@ static DEVICE_ATTR(enable, 0644, static int __init h1940bt_probe(struct platform_device *pdev) { /* Configures BT serial port GPIOs */ - s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0); - s3c2410_gpio_pullup(S3C2410_GPH0, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPH1_OUTP); - s3c2410_gpio_pullup(S3C2410_GPH1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0); - s3c2410_gpio_pullup(S3C2410_GPH2, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0); - s3c2410_gpio_pullup(S3C2410_GPH3, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); + s3c2410_gpio_pullup(S3C2410_GPH(0), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_pullup(S3C2410_GPH(1), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0); + s3c2410_gpio_pullup(S3C2410_GPH(2), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0); + s3c2410_gpio_pullup(S3C2410_GPH(3), 1); #ifdef CONFIG_LEDS_H1940 led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger); diff --git a/arch/arm/mach-s3c2410/include/mach/dma.h b/arch/arm/mach-s3c2410/include/mach/dma.h index 13358ce2128c..c3a2629e0ded 100644 --- a/arch/arm/mach-s3c2410/include/mach/dma.h +++ b/arch/arm/mach-s3c2410/include/mach/dma.h @@ -3,7 +3,7 @@ * Copyright (C) 2003,2004,2006 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> * - * Samsung S3C241XX DMA support + * Samsung S3C24XX DMA support * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -13,8 +13,8 @@ #ifndef __ASM_ARCH_DMA_H #define __ASM_ARCH_DMA_H __FILE__ +#include <plat/dma.h> #include <linux/sysdev.h> -#include <mach/hardware.h> #define MAX_DMA_TRANSFER_SIZE 0x100000 /* Data Unit is half word */ @@ -55,9 +55,9 @@ enum dma_ch { /* we have 4 dma channels */ #ifndef CONFIG_CPU_S3C2443 -#define S3C2410_DMA_CHANNELS (4) +#define S3C_DMA_CHANNELS (4) #else -#define S3C2410_DMA_CHANNELS (6) +#define S3C_DMA_CHANNELS (6) #endif /* types */ @@ -68,7 +68,6 @@ enum s3c2410_dma_state { S3C2410_DMA_PAUSED }; - /* enum s3c2410_dma_loadst * * This represents the state of the DMA engine, wrt to the loaded / running @@ -104,32 +103,6 @@ enum s3c2410_dma_loadst { S3C2410_DMALOAD_1LOADED_1RUNNING, }; -enum s3c2410_dma_buffresult { - S3C2410_RES_OK, - S3C2410_RES_ERR, - S3C2410_RES_ABORT -}; - -enum s3c2410_dmasrc { - S3C2410_DMASRC_HW, /* source is memory */ - S3C2410_DMASRC_MEM /* source is hardware */ -}; - -/* enum s3c2410_chan_op - * - * operation codes passed to the DMA code by the user, and also used - * to inform the current channel owner of any changes to the system state -*/ - -enum s3c2410_chan_op { - S3C2410_DMAOP_START, - S3C2410_DMAOP_STOP, - S3C2410_DMAOP_PAUSE, - S3C2410_DMAOP_RESUME, - S3C2410_DMAOP_FLUSH, - S3C2410_DMAOP_TIMEOUT, /* internal signal to handler */ - S3C2410_DMAOP_STARTED, /* indicate channel started */ -}; /* flags */ @@ -139,17 +112,14 @@ enum s3c2410_chan_op { /* dma buffer */ -struct s3c2410_dma_client { - char *name; -}; +struct s3c2410_dma_buf; -/* s3c2410_dma_buf_s +/* s3c2410_dma_buf * * internally used buffer structure to describe a queued or running * buffer. */ -struct s3c2410_dma_buf; struct s3c2410_dma_buf { struct s3c2410_dma_buf *next; int magic; /* magic */ @@ -161,20 +131,6 @@ struct s3c2410_dma_buf { /* [1] is this updated for both recv/send modes? */ -struct s3c2410_dma_chan; - -/* s3c2410_dma_cbfn_t - * - * buffer callback routine type -*/ - -typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *, - void *buf, int size, - enum s3c2410_dma_buffresult result); - -typedef int (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *, - enum s3c2410_chan_op ); - struct s3c2410_dma_stats { unsigned long loads; unsigned long timeout_longest; @@ -206,10 +162,10 @@ struct s3c2410_dma_chan { /* channel configuration */ enum s3c2410_dmasrc source; + enum dma_ch req_ch; unsigned long dev_addr; unsigned long load_timeout; unsigned int flags; /* channel flags */ - unsigned int hw_cfg; /* last hw config */ struct s3c24xx_dma_map *map; /* channel hw maps */ @@ -236,213 +192,6 @@ struct s3c2410_dma_chan { struct sys_device dev; }; -/* the currently allocated channel information */ -extern struct s3c2410_dma_chan s3c2410_chans[]; - -/* note, we don't really use dma_device_t at the moment */ typedef unsigned long dma_device_t; -/* functions --------------------------------------------------------------- */ - -/* s3c2410_dma_request - * - * request a dma channel exclusivley -*/ - -extern int s3c2410_dma_request(unsigned int channel, - struct s3c2410_dma_client *, void *dev); - - -/* s3c2410_dma_ctrl - * - * change the state of the dma channel -*/ - -extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op); - -/* s3c2410_dma_setflags - * - * set the channel's flags to a given state -*/ - -extern int s3c2410_dma_setflags(unsigned int channel, - unsigned int flags); - -/* s3c2410_dma_free - * - * free the dma channel (will also abort any outstanding operations) -*/ - -extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *); - -/* s3c2410_dma_enqueue - * - * place the given buffer onto the queue of operations for the channel. - * The buffer must be allocated from dma coherent memory, or the Dcache/WB - * drained before the buffer is given to the DMA system. -*/ - -extern int s3c2410_dma_enqueue(unsigned int channel, void *id, - dma_addr_t data, int size); - -/* s3c2410_dma_config - * - * configure the dma channel -*/ - -extern int s3c2410_dma_config(unsigned int channel, int xferunit, int dcon); - -/* s3c2410_dma_devconfig - * - * configure the device we're talking to -*/ - -extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source, - int hwcfg, unsigned long devaddr); - -/* s3c2410_dma_getposition - * - * get the position that the dma transfer is currently at -*/ - -extern int s3c2410_dma_getposition(unsigned int channel, - dma_addr_t *src, dma_addr_t *dest); - -extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn); -extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn); - -/* DMA Register definitions */ - -#define S3C2410_DMA_DISRC (0x00) -#define S3C2410_DMA_DISRCC (0x04) -#define S3C2410_DMA_DIDST (0x08) -#define S3C2410_DMA_DIDSTC (0x0C) -#define S3C2410_DMA_DCON (0x10) -#define S3C2410_DMA_DSTAT (0x14) -#define S3C2410_DMA_DCSRC (0x18) -#define S3C2410_DMA_DCDST (0x1C) -#define S3C2410_DMA_DMASKTRIG (0x20) -#define S3C2412_DMA_DMAREQSEL (0x24) -#define S3C2443_DMA_DMAREQSEL (0x24) - -#define S3C2410_DISRCC_INC (1<<0) -#define S3C2410_DISRCC_APB (1<<1) - -#define S3C2410_DMASKTRIG_STOP (1<<2) -#define S3C2410_DMASKTRIG_ON (1<<1) -#define S3C2410_DMASKTRIG_SWTRIG (1<<0) - -#define S3C2410_DCON_DEMAND (0<<31) -#define S3C2410_DCON_HANDSHAKE (1<<31) -#define S3C2410_DCON_SYNC_PCLK (0<<30) -#define S3C2410_DCON_SYNC_HCLK (1<<30) - -#define S3C2410_DCON_INTREQ (1<<29) - -#define S3C2410_DCON_CH0_XDREQ0 (0<<24) -#define S3C2410_DCON_CH0_UART0 (1<<24) -#define S3C2410_DCON_CH0_SDI (2<<24) -#define S3C2410_DCON_CH0_TIMER (3<<24) -#define S3C2410_DCON_CH0_USBEP1 (4<<24) - -#define S3C2410_DCON_CH1_XDREQ1 (0<<24) -#define S3C2410_DCON_CH1_UART1 (1<<24) -#define S3C2410_DCON_CH1_I2SSDI (2<<24) -#define S3C2410_DCON_CH1_SPI (3<<24) -#define S3C2410_DCON_CH1_USBEP2 (4<<24) - -#define S3C2410_DCON_CH2_I2SSDO (0<<24) -#define S3C2410_DCON_CH2_I2SSDI (1<<24) -#define S3C2410_DCON_CH2_SDI (2<<24) -#define S3C2410_DCON_CH2_TIMER (3<<24) -#define S3C2410_DCON_CH2_USBEP3 (4<<24) - -#define S3C2410_DCON_CH3_UART2 (0<<24) -#define S3C2410_DCON_CH3_SDI (1<<24) -#define S3C2410_DCON_CH3_SPI (2<<24) -#define S3C2410_DCON_CH3_TIMER (3<<24) -#define S3C2410_DCON_CH3_USBEP4 (4<<24) - -#define S3C2410_DCON_SRCSHIFT (24) -#define S3C2410_DCON_SRCMASK (7<<24) - -#define S3C2410_DCON_BYTE (0<<20) -#define S3C2410_DCON_HALFWORD (1<<20) -#define S3C2410_DCON_WORD (2<<20) - -#define S3C2410_DCON_AUTORELOAD (0<<22) -#define S3C2410_DCON_NORELOAD (1<<22) -#define S3C2410_DCON_HWTRIG (1<<23) - -#ifdef CONFIG_CPU_S3C2440 -#define S3C2440_DIDSTC_CHKINT (1<<2) - -#define S3C2440_DCON_CH0_I2SSDO (5<<24) -#define S3C2440_DCON_CH0_PCMIN (6<<24) - -#define S3C2440_DCON_CH1_PCMOUT (5<<24) -#define S3C2440_DCON_CH1_SDI (6<<24) - -#define S3C2440_DCON_CH2_PCMIN (5<<24) -#define S3C2440_DCON_CH2_MICIN (6<<24) - -#define S3C2440_DCON_CH3_MICIN (5<<24) -#define S3C2440_DCON_CH3_PCMOUT (6<<24) -#endif - -#ifdef CONFIG_CPU_S3C2412 - -#define S3C2412_DMAREQSEL_SRC(x) ((x)<<1) - -#define S3C2412_DMAREQSEL_HW (1) - -#define S3C2412_DMAREQSEL_SPI0TX S3C2412_DMAREQSEL_SRC(0) -#define S3C2412_DMAREQSEL_SPI0RX S3C2412_DMAREQSEL_SRC(1) -#define S3C2412_DMAREQSEL_SPI1TX S3C2412_DMAREQSEL_SRC(2) -#define S3C2412_DMAREQSEL_SPI1RX S3C2412_DMAREQSEL_SRC(3) -#define S3C2412_DMAREQSEL_I2STX S3C2412_DMAREQSEL_SRC(4) -#define S3C2412_DMAREQSEL_I2SRX S3C2412_DMAREQSEL_SRC(5) -#define S3C2412_DMAREQSEL_TIMER S3C2412_DMAREQSEL_SRC(9) -#define S3C2412_DMAREQSEL_SDI S3C2412_DMAREQSEL_SRC(10) -#define S3C2412_DMAREQSEL_USBEP1 S3C2412_DMAREQSEL_SRC(13) -#define S3C2412_DMAREQSEL_USBEP2 S3C2412_DMAREQSEL_SRC(14) -#define S3C2412_DMAREQSEL_USBEP3 S3C2412_DMAREQSEL_SRC(15) -#define S3C2412_DMAREQSEL_USBEP4 S3C2412_DMAREQSEL_SRC(16) -#define S3C2412_DMAREQSEL_XDREQ0 S3C2412_DMAREQSEL_SRC(17) -#define S3C2412_DMAREQSEL_XDREQ1 S3C2412_DMAREQSEL_SRC(18) -#define S3C2412_DMAREQSEL_UART0_0 S3C2412_DMAREQSEL_SRC(19) -#define S3C2412_DMAREQSEL_UART0_1 S3C2412_DMAREQSEL_SRC(20) -#define S3C2412_DMAREQSEL_UART1_0 S3C2412_DMAREQSEL_SRC(21) -#define S3C2412_DMAREQSEL_UART1_1 S3C2412_DMAREQSEL_SRC(22) -#define S3C2412_DMAREQSEL_UART2_0 S3C2412_DMAREQSEL_SRC(23) -#define S3C2412_DMAREQSEL_UART2_1 S3C2412_DMAREQSEL_SRC(24) - -#endif - -#define S3C2443_DMAREQSEL_SRC(x) ((x)<<1) - -#define S3C2443_DMAREQSEL_HW (1) - -#define S3C2443_DMAREQSEL_SPI0TX S3C2443_DMAREQSEL_SRC(0) -#define S3C2443_DMAREQSEL_SPI0RX S3C2443_DMAREQSEL_SRC(1) -#define S3C2443_DMAREQSEL_SPI1TX S3C2443_DMAREQSEL_SRC(2) -#define S3C2443_DMAREQSEL_SPI1RX S3C2443_DMAREQSEL_SRC(3) -#define S3C2443_DMAREQSEL_I2STX S3C2443_DMAREQSEL_SRC(4) -#define S3C2443_DMAREQSEL_I2SRX S3C2443_DMAREQSEL_SRC(5) -#define S3C2443_DMAREQSEL_TIMER S3C2443_DMAREQSEL_SRC(9) -#define S3C2443_DMAREQSEL_SDI S3C2443_DMAREQSEL_SRC(10) -#define S3C2443_DMAREQSEL_XDREQ0 S3C2443_DMAREQSEL_SRC(17) -#define S3C2443_DMAREQSEL_XDREQ1 S3C2443_DMAREQSEL_SRC(18) -#define S3C2443_DMAREQSEL_UART0_0 S3C2443_DMAREQSEL_SRC(19) -#define S3C2443_DMAREQSEL_UART0_1 S3C2443_DMAREQSEL_SRC(20) -#define S3C2443_DMAREQSEL_UART1_0 S3C2443_DMAREQSEL_SRC(21) -#define S3C2443_DMAREQSEL_UART1_1 S3C2443_DMAREQSEL_SRC(22) -#define S3C2443_DMAREQSEL_UART2_0 S3C2443_DMAREQSEL_SRC(23) -#define S3C2443_DMAREQSEL_UART2_1 S3C2443_DMAREQSEL_SRC(24) -#define S3C2443_DMAREQSEL_UART3_0 S3C2443_DMAREQSEL_SRC(25) -#define S3C2443_DMAREQSEL_UART3_1 S3C2443_DMAREQSEL_SRC(26) -#define S3C2443_DMAREQSEL_PCMOUT S3C2443_DMAREQSEL_SRC(27) -#define S3C2443_DMAREQSEL_PCMIN S3C2443_DMAREQSEL_SRC(28) -#define S3C2443_DMAREQSEL_MICIN S3C2443_DMAREQSEL_SRC(29) - #endif /* __ASM_ARCH_DMA_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h index 6c9fbb99ef14..8fe192081d3a 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h @@ -24,7 +24,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) { struct s3c_gpio_chip *chip; - if (pin > S3C2410_GPG10) + if (pin > S3C2410_GPG(10)) return NULL; chip = &s3c24xx_gpios[pin/32]; diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h new file mode 100644 index 000000000000..801dff13858d --- /dev/null +++ b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h @@ -0,0 +1,103 @@ +/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h + * + * Copyright (c) 2003,2009 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2410 - hardware + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* These functions are in the to-be-removed category and it is strongly + * encouraged not to use these in new code. They will be marked deprecated + * very soon. + * + * Most of the functionality can be either replaced by the gpiocfg calls + * for the s3c platform or by the generic GPIOlib API. +*/ + +/* external functions for GPIO support + * + * These allow various different clients to access the same GPIO + * registers without conflicting. If your driver only owns the entire + * GPIO register, then it is safe to ioremap/__raw_{read|write} to it. +*/ + +/* s3c2410_gpio_cfgpin + * + * set the configuration of the given pin to the value passed. + * + * eg: + * s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0); + * s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1); +*/ + +extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function); + +extern unsigned int s3c2410_gpio_getcfg(unsigned int pin); + +/* s3c2410_gpio_getirq + * + * turn the given pin number into the corresponding IRQ number + * + * returns: + * < 0 = no interrupt for this pin + * >=0 = interrupt number for the pin +*/ + +extern int s3c2410_gpio_getirq(unsigned int pin); + +#ifdef CONFIG_CPU_S3C2400 + +extern int s3c2400_gpio_getirq(unsigned int pin); + +#endif /* CONFIG_CPU_S3C2400 */ + +/* s3c2410_gpio_irqfilter + * + * set the irq filtering on the given pin + * + * on = 0 => disable filtering + * 1 => enable filtering + * + * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with + * width of filter (0 through 63) + * + * +*/ + +extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, + unsigned int config); + +/* s3c2410_gpio_pullup + * + * configure the pull-up control on the given pin + * + * to = 1 => disable the pull-up + * 0 => enable the pull-up + * + * eg; + * + * s3c2410_gpio_pullup(S3C2410_GPB(0), 0); + * s3c2410_gpio_pullup(S3C2410_GPE(8), 0); +*/ + +extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to); + +/* s3c2410_gpio_getpull + * + * Read the state of the pull-up on a given pin + * + * return: + * < 0 => error code + * 0 => enabled + * 1 => disabled +*/ + +extern int s3c2410_gpio_getpull(unsigned int pin); + +extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to); + +extern unsigned int s3c2410_gpio_getpin(unsigned int pin); diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h index ce1ec69806a1..2edbb9c88ab3 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h @@ -11,6 +11,9 @@ * published by the Free Software Foundation. */ +#ifndef __MACH_GPIONRS_H +#define __MACH_GPIONRS_H + #define S3C2410_GPIONO(bank,offset) ((bank) + (offset)) #define S3C2410_GPIO_BANKA (32*0) @@ -21,3 +24,70 @@ #define S3C2410_GPIO_BANKF (32*5) #define S3C2410_GPIO_BANKG (32*6) #define S3C2410_GPIO_BANKH (32*7) + +/* GPIO bank sizes */ +#define S3C2410_GPIO_A_NR (32) +#define S3C2410_GPIO_B_NR (32) +#define S3C2410_GPIO_C_NR (32) +#define S3C2410_GPIO_D_NR (32) +#define S3C2410_GPIO_E_NR (32) +#define S3C2410_GPIO_F_NR (32) +#define S3C2410_GPIO_G_NR (32) +#define S3C2410_GPIO_H_NR (32) + +#if CONFIG_S3C_GPIO_SPACE != 0 +#error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment +#endif + +#define S3C2410_GPIO_NEXT(__gpio) \ + ((__gpio##_START) + (__gpio##_NR) + CONFIG_S3C_GPIO_SPACE + 0) + +#ifndef __ASSEMBLY__ + +enum s3c_gpio_number { + S3C2410_GPIO_A_START = 0, + S3C2410_GPIO_B_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_A), + S3C2410_GPIO_C_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_B), + S3C2410_GPIO_D_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_C), + S3C2410_GPIO_E_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_D), + S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E), + S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F), + S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G), +}; + +#endif /* __ASSEMBLY__ */ + +/* S3C2410 GPIO number definitions. */ + +#define S3C2410_GPA(_nr) (S3C2410_GPIO_A_START + (_nr)) +#define S3C2410_GPB(_nr) (S3C2410_GPIO_B_START + (_nr)) +#define S3C2410_GPC(_nr) (S3C2410_GPIO_C_START + (_nr)) +#define S3C2410_GPD(_nr) (S3C2410_GPIO_D_START + (_nr)) +#define S3C2410_GPE(_nr) (S3C2410_GPIO_E_START + (_nr)) +#define S3C2410_GPF(_nr) (S3C2410_GPIO_F_START + (_nr)) +#define S3C2410_GPG(_nr) (S3C2410_GPIO_G_START + (_nr)) +#define S3C2410_GPH(_nr) (S3C2410_GPIO_H_START + (_nr)) + +/* compatibility until drivers can be modified */ + +#define S3C2410_GPA0 S3C2410_GPA(0) +#define S3C2410_GPA1 S3C2410_GPA(1) +#define S3C2410_GPA3 S3C2410_GPA(3) +#define S3C2410_GPA7 S3C2410_GPA(7) + +#define S3C2410_GPE0 S3C2410_GPE(0) +#define S3C2410_GPE1 S3C2410_GPE(1) +#define S3C2410_GPE2 S3C2410_GPE(2) +#define S3C2410_GPE3 S3C2410_GPE(3) +#define S3C2410_GPE4 S3C2410_GPE(4) +#define S3C2410_GPE5 S3C2410_GPE(5) +#define S3C2410_GPE6 S3C2410_GPE(6) +#define S3C2410_GPE7 S3C2410_GPE(7) +#define S3C2410_GPE8 S3C2410_GPE(8) +#define S3C2410_GPE9 S3C2410_GPE(9) +#define S3C2410_GPE10 S3C2410_GPE(10) + +#define S3C2410_GPH10 S3C2410_GPH(10) + +#endif /* __MACH_GPIONRS_H */ + diff --git a/arch/arm/mach-s3c2410/include/mach/gpio.h b/arch/arm/mach-s3c2410/include/mach/gpio.h index 51a88cf9526b..15f0b3e7ce69 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio.h @@ -24,5 +24,6 @@ #include <asm-generic/gpio.h> #include <mach/gpio-nrs.h> +#include <mach/gpio-fns.h> #define S3C_GPIO_END (S3C2410_GPIO_BANKH + 32) diff --git a/arch/arm/mach-s3c2410/include/mach/hardware.h b/arch/arm/mach-s3c2410/include/mach/hardware.h index 74d5a1a4024c..aef5631eac58 100644 --- a/arch/arm/mach-s3c2410/include/mach/hardware.h +++ b/arch/arm/mach-s3c2410/include/mach/hardware.h @@ -15,101 +15,6 @@ #ifndef __ASSEMBLY__ -/* external functions for GPIO support - * - * These allow various different clients to access the same GPIO - * registers without conflicting. If your driver only owns the entire - * GPIO register, then it is safe to ioremap/__raw_{read|write} to it. -*/ - -/* s3c2410_gpio_cfgpin - * - * set the configuration of the given pin to the value passed. - * - * eg: - * s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0); - * s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1); -*/ - -extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function); - -extern unsigned int s3c2410_gpio_getcfg(unsigned int pin); - -/* s3c2410_gpio_getirq - * - * turn the given pin number into the corresponding IRQ number - * - * returns: - * < 0 = no interrupt for this pin - * >=0 = interrupt number for the pin -*/ - -extern int s3c2410_gpio_getirq(unsigned int pin); - -/* s3c2410_gpio_irq2pin - * - * turn the given irq number into the corresponding GPIO number - * - * returns: - * < 0 = no pin - * >=0 = gpio pin number -*/ - -extern int s3c2410_gpio_irq2pin(unsigned int irq); - -#ifdef CONFIG_CPU_S3C2400 - -extern int s3c2400_gpio_getirq(unsigned int pin); - -#endif /* CONFIG_CPU_S3C2400 */ - -/* s3c2410_gpio_irqfilter - * - * set the irq filtering on the given pin - * - * on = 0 => disable filtering - * 1 => enable filtering - * - * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with - * width of filter (0 through 63) - * - * -*/ - -extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, - unsigned int config); - -/* s3c2410_gpio_pullup - * - * configure the pull-up control on the given pin - * - * to = 1 => disable the pull-up - * 0 => enable the pull-up - * - * eg; - * - * s3c2410_gpio_pullup(S3C2410_GPB0, 0); - * s3c2410_gpio_pullup(S3C2410_GPE8, 0); -*/ - -extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to); - -/* s3c2410_gpio_getpull - * - * Read the state of the pull-up on a given pin - * - * return: - * < 0 => error code - * 0 => enabled - * 1 => disabled -*/ - -extern int s3c2410_gpio_getpull(unsigned int pin); - -extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to); - -extern unsigned int s3c2410_gpio_getpin(unsigned int pin); - extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg); #ifdef CONFIG_CPU_S3C2440 diff --git a/arch/arm/mach-s3c2410/include/mach/map.h b/arch/arm/mach-s3c2410/include/mach/map.h index 255fdfeaf957..e99b212cb1ca 100644 --- a/arch/arm/mach-s3c2410/include/mach/map.h +++ b/arch/arm/mach-s3c2410/include/mach/map.h @@ -84,7 +84,6 @@ #define S3C24XX_PA_IRQ S3C2410_PA_IRQ #define S3C24XX_PA_MEMCTRL S3C2410_PA_MEMCTRL -#define S3C24XX_PA_USBHOST S3C2410_PA_USBHOST #define S3C24XX_PA_DMA S3C2410_PA_DMA #define S3C24XX_PA_CLKPWR S3C2410_PA_CLKPWR #define S3C24XX_PA_LCD S3C2410_PA_LCD @@ -102,6 +101,7 @@ #define S3C_PA_IIC S3C2410_PA_IIC #define S3C_PA_UART S3C24XX_PA_UART +#define S3C_PA_USBHOST S3C2410_PA_USBHOST #define S3C_PA_HSMMC0 S3C2443_PA_HSMMC #endif /* __ASM_ARCH_MAP_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h index 35a03df473fc..b278d0c45ccf 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h @@ -69,104 +69,58 @@ #define S3C2400_GPACON S3C2410_GPIOREG(0x00) #define S3C2400_GPADAT S3C2410_GPIOREG(0x04) -#define S3C2410_GPA0 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 0) -#define S3C2410_GPA0_OUT (0<<0) #define S3C2410_GPA0_ADDR0 (1<<0) -#define S3C2410_GPA1 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 1) -#define S3C2410_GPA1_OUT (0<<1) #define S3C2410_GPA1_ADDR16 (1<<1) -#define S3C2410_GPA2 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 2) -#define S3C2410_GPA2_OUT (0<<2) #define S3C2410_GPA2_ADDR17 (1<<2) -#define S3C2410_GPA3 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 3) -#define S3C2410_GPA3_OUT (0<<3) #define S3C2410_GPA3_ADDR18 (1<<3) -#define S3C2410_GPA4 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 4) -#define S3C2410_GPA4_OUT (0<<4) #define S3C2410_GPA4_ADDR19 (1<<4) -#define S3C2410_GPA5 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 5) -#define S3C2410_GPA5_OUT (0<<5) #define S3C2410_GPA5_ADDR20 (1<<5) -#define S3C2410_GPA6 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 6) -#define S3C2410_GPA6_OUT (0<<6) #define S3C2410_GPA6_ADDR21 (1<<6) -#define S3C2410_GPA7 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 7) -#define S3C2410_GPA7_OUT (0<<7) #define S3C2410_GPA7_ADDR22 (1<<7) -#define S3C2410_GPA8 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 8) -#define S3C2410_GPA8_OUT (0<<8) #define S3C2410_GPA8_ADDR23 (1<<8) -#define S3C2410_GPA9 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 9) -#define S3C2410_GPA9_OUT (0<<9) #define S3C2410_GPA9_ADDR24 (1<<9) -#define S3C2410_GPA10 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 10) -#define S3C2410_GPA10_OUT (0<<10) #define S3C2410_GPA10_ADDR25 (1<<10) #define S3C2400_GPA10_SCKE (1<<10) -#define S3C2410_GPA11 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 11) -#define S3C2410_GPA11_OUT (0<<11) #define S3C2410_GPA11_ADDR26 (1<<11) #define S3C2400_GPA11_nCAS0 (1<<11) -#define S3C2410_GPA12 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 12) -#define S3C2410_GPA12_OUT (0<<12) #define S3C2410_GPA12_nGCS1 (1<<12) #define S3C2400_GPA12_nCAS1 (1<<12) -#define S3C2410_GPA13 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 13) -#define S3C2410_GPA13_OUT (0<<13) #define S3C2410_GPA13_nGCS2 (1<<13) #define S3C2400_GPA13_nGCS1 (1<<13) -#define S3C2410_GPA14 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 14) -#define S3C2410_GPA14_OUT (0<<14) #define S3C2410_GPA14_nGCS3 (1<<14) #define S3C2400_GPA14_nGCS2 (1<<14) -#define S3C2410_GPA15 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 15) -#define S3C2410_GPA15_OUT (0<<15) #define S3C2410_GPA15_nGCS4 (1<<15) #define S3C2400_GPA15_nGCS3 (1<<15) -#define S3C2410_GPA16 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 16) -#define S3C2410_GPA16_OUT (0<<16) #define S3C2410_GPA16_nGCS5 (1<<16) #define S3C2400_GPA16_nGCS4 (1<<16) -#define S3C2410_GPA17 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 17) -#define S3C2410_GPA17_OUT (0<<17) #define S3C2410_GPA17_CLE (1<<17) #define S3C2400_GPA17_nGCS5 (1<<17) -#define S3C2410_GPA18 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 18) -#define S3C2410_GPA18_OUT (0<<18) #define S3C2410_GPA18_ALE (1<<18) -#define S3C2410_GPA19 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 19) -#define S3C2410_GPA19_OUT (0<<19) #define S3C2410_GPA19_nFWE (1<<19) -#define S3C2410_GPA20 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 20) -#define S3C2410_GPA20_OUT (0<<20) #define S3C2410_GPA20_nFRE (1<<20) -#define S3C2410_GPA21 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 21) -#define S3C2410_GPA21_OUT (0<<21) #define S3C2410_GPA21_nRSTOUT (1<<21) -#define S3C2410_GPA22 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 22) -#define S3C2410_GPA22_OUT (0<<22) #define S3C2410_GPA22_nFCE (1<<22) /* 0x08 and 0x0c are reserved on S3C2410 */ @@ -194,107 +148,69 @@ /* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */ -#define S3C2410_GPB0 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 0) -#define S3C2410_GPB0_INP (0x00 << 0) -#define S3C2410_GPB0_OUTP (0x01 << 0) #define S3C2410_GPB0_TOUT0 (0x02 << 0) #define S3C2400_GPB0_DATA16 (0x02 << 0) -#define S3C2410_GPB1 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 1) -#define S3C2410_GPB1_INP (0x00 << 2) -#define S3C2410_GPB1_OUTP (0x01 << 2) #define S3C2410_GPB1_TOUT1 (0x02 << 2) #define S3C2400_GPB1_DATA17 (0x02 << 2) -#define S3C2410_GPB2 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 2) -#define S3C2410_GPB2_INP (0x00 << 4) -#define S3C2410_GPB2_OUTP (0x01 << 4) #define S3C2410_GPB2_TOUT2 (0x02 << 4) #define S3C2400_GPB2_DATA18 (0x02 << 4) #define S3C2400_GPB2_TCLK1 (0x03 << 4) -#define S3C2410_GPB3 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 3) -#define S3C2410_GPB3_INP (0x00 << 6) -#define S3C2410_GPB3_OUTP (0x01 << 6) #define S3C2410_GPB3_TOUT3 (0x02 << 6) #define S3C2400_GPB3_DATA19 (0x02 << 6) #define S3C2400_GPB3_TXD1 (0x03 << 6) -#define S3C2410_GPB4 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 4) -#define S3C2410_GPB4_INP (0x00 << 8) -#define S3C2410_GPB4_OUTP (0x01 << 8) #define S3C2410_GPB4_TCLK0 (0x02 << 8) #define S3C2400_GPB4_DATA20 (0x02 << 8) #define S3C2410_GPB4_MASK (0x03 << 8) #define S3C2400_GPB4_RXD1 (0x03 << 8) #define S3C2400_GPB4_MASK (0x03 << 8) -#define S3C2410_GPB5 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 5) -#define S3C2410_GPB5_INP (0x00 << 10) -#define S3C2410_GPB5_OUTP (0x01 << 10) #define S3C2410_GPB5_nXBACK (0x02 << 10) #define S3C2443_GPB5_XBACK (0x03 << 10) #define S3C2400_GPB5_DATA21 (0x02 << 10) #define S3C2400_GPB5_nCTS1 (0x03 << 10) -#define S3C2410_GPB6 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 6) -#define S3C2410_GPB6_INP (0x00 << 12) -#define S3C2410_GPB6_OUTP (0x01 << 12) #define S3C2410_GPB6_nXBREQ (0x02 << 12) #define S3C2443_GPB6_XBREQ (0x03 << 12) #define S3C2400_GPB6_DATA22 (0x02 << 12) #define S3C2400_GPB6_nRTS1 (0x03 << 12) -#define S3C2410_GPB7 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 7) -#define S3C2410_GPB7_INP (0x00 << 14) -#define S3C2410_GPB7_OUTP (0x01 << 14) #define S3C2410_GPB7_nXDACK1 (0x02 << 14) #define S3C2443_GPB7_XDACK1 (0x03 << 14) #define S3C2400_GPB7_DATA23 (0x02 << 14) -#define S3C2410_GPB8 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 8) -#define S3C2410_GPB8_INP (0x00 << 16) -#define S3C2410_GPB8_OUTP (0x01 << 16) #define S3C2410_GPB8_nXDREQ1 (0x02 << 16) #define S3C2400_GPB8_DATA24 (0x02 << 16) -#define S3C2410_GPB9 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 9) -#define S3C2410_GPB9_INP (0x00 << 18) -#define S3C2410_GPB9_OUTP (0x01 << 18) #define S3C2410_GPB9_nXDACK0 (0x02 << 18) #define S3C2443_GPB9_XDACK0 (0x03 << 18) #define S3C2400_GPB9_DATA25 (0x02 << 18) #define S3C2400_GPB9_I2SSDI (0x03 << 18) -#define S3C2410_GPB10 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 10) -#define S3C2410_GPB10_INP (0x00 << 20) -#define S3C2410_GPB10_OUTP (0x01 << 20) #define S3C2410_GPB10_nXDRE0 (0x02 << 20) #define S3C2443_GPB10_XDREQ0 (0x03 << 20) #define S3C2400_GPB10_DATA26 (0x02 << 20) #define S3C2400_GPB10_nSS (0x03 << 20) -#define S3C2400_GPB11 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 11) #define S3C2400_GPB11_INP (0x00 << 22) #define S3C2400_GPB11_OUTP (0x01 << 22) #define S3C2400_GPB11_DATA27 (0x02 << 22) -#define S3C2400_GPB12 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 12) #define S3C2400_GPB12_INP (0x00 << 24) #define S3C2400_GPB12_OUTP (0x01 << 24) #define S3C2400_GPB12_DATA28 (0x02 << 24) -#define S3C2400_GPB13 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 13) #define S3C2400_GPB13_INP (0x00 << 26) #define S3C2400_GPB13_OUTP (0x01 << 26) #define S3C2400_GPB13_DATA29 (0x02 << 26) -#define S3C2400_GPB14 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 14) #define S3C2400_GPB14_INP (0x00 << 28) #define S3C2400_GPB14_OUTP (0x01 << 28) #define S3C2400_GPB14_DATA30 (0x02 << 28) -#define S3C2400_GPB15 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 15) #define S3C2400_GPB15_INP (0x00 << 30) #define S3C2400_GPB15_OUTP (0x01 << 30) #define S3C2400_GPB15_DATA31 (0x02 << 30) @@ -315,99 +231,51 @@ #define S3C2400_GPCDAT S3C2410_GPIOREG(0x18) #define S3C2400_GPCUP S3C2410_GPIOREG(0x1C) -#define S3C2410_GPC0 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 0) -#define S3C2410_GPC0_INP (0x00 << 0) -#define S3C2410_GPC0_OUTP (0x01 << 0) #define S3C2410_GPC0_LEND (0x02 << 0) #define S3C2400_GPC0_VD0 (0x02 << 0) -#define S3C2410_GPC1 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 1) -#define S3C2410_GPC1_INP (0x00 << 2) -#define S3C2410_GPC1_OUTP (0x01 << 2) #define S3C2410_GPC1_VCLK (0x02 << 2) #define S3C2400_GPC1_VD1 (0x02 << 2) -#define S3C2410_GPC2 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 2) -#define S3C2410_GPC2_INP (0x00 << 4) -#define S3C2410_GPC2_OUTP (0x01 << 4) #define S3C2410_GPC2_VLINE (0x02 << 4) #define S3C2400_GPC2_VD2 (0x02 << 4) -#define S3C2410_GPC3 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 3) -#define S3C2410_GPC3_INP (0x00 << 6) -#define S3C2410_GPC3_OUTP (0x01 << 6) #define S3C2410_GPC3_VFRAME (0x02 << 6) #define S3C2400_GPC3_VD3 (0x02 << 6) -#define S3C2410_GPC4 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 4) -#define S3C2410_GPC4_INP (0x00 << 8) -#define S3C2410_GPC4_OUTP (0x01 << 8) #define S3C2410_GPC4_VM (0x02 << 8) #define S3C2400_GPC4_VD4 (0x02 << 8) -#define S3C2410_GPC5 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 5) -#define S3C2410_GPC5_INP (0x00 << 10) -#define S3C2410_GPC5_OUTP (0x01 << 10) #define S3C2410_GPC5_LCDVF0 (0x02 << 10) #define S3C2400_GPC5_VD5 (0x02 << 10) -#define S3C2410_GPC6 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 6) -#define S3C2410_GPC6_INP (0x00 << 12) -#define S3C2410_GPC6_OUTP (0x01 << 12) #define S3C2410_GPC6_LCDVF1 (0x02 << 12) #define S3C2400_GPC6_VD6 (0x02 << 12) -#define S3C2410_GPC7 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 7) -#define S3C2410_GPC7_INP (0x00 << 14) -#define S3C2410_GPC7_OUTP (0x01 << 14) #define S3C2410_GPC7_LCDVF2 (0x02 << 14) #define S3C2400_GPC7_VD7 (0x02 << 14) -#define S3C2410_GPC8 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 8) -#define S3C2410_GPC8_INP (0x00 << 16) -#define S3C2410_GPC8_OUTP (0x01 << 16) #define S3C2410_GPC8_VD0 (0x02 << 16) #define S3C2400_GPC8_VD8 (0x02 << 16) -#define S3C2410_GPC9 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 9) -#define S3C2410_GPC9_INP (0x00 << 18) -#define S3C2410_GPC9_OUTP (0x01 << 18) #define S3C2410_GPC9_VD1 (0x02 << 18) #define S3C2400_GPC9_VD9 (0x02 << 18) -#define S3C2410_GPC10 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 10) -#define S3C2410_GPC10_INP (0x00 << 20) -#define S3C2410_GPC10_OUTP (0x01 << 20) #define S3C2410_GPC10_VD2 (0x02 << 20) #define S3C2400_GPC10_VD10 (0x02 << 20) -#define S3C2410_GPC11 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 11) -#define S3C2410_GPC11_INP (0x00 << 22) -#define S3C2410_GPC11_OUTP (0x01 << 22) #define S3C2410_GPC11_VD3 (0x02 << 22) #define S3C2400_GPC11_VD11 (0x02 << 22) -#define S3C2410_GPC12 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 12) -#define S3C2410_GPC12_INP (0x00 << 24) -#define S3C2410_GPC12_OUTP (0x01 << 24) #define S3C2410_GPC12_VD4 (0x02 << 24) #define S3C2400_GPC12_VD12 (0x02 << 24) -#define S3C2410_GPC13 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 13) -#define S3C2410_GPC13_INP (0x00 << 26) -#define S3C2410_GPC13_OUTP (0x01 << 26) #define S3C2410_GPC13_VD5 (0x02 << 26) #define S3C2400_GPC13_VD13 (0x02 << 26) -#define S3C2410_GPC14 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 14) -#define S3C2410_GPC14_INP (0x00 << 28) -#define S3C2410_GPC14_OUTP (0x01 << 28) #define S3C2410_GPC14_VD6 (0x02 << 28) #define S3C2400_GPC14_VD14 (0x02 << 28) -#define S3C2410_GPC15 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 15) -#define S3C2410_GPC15_INP (0x00 << 30) -#define S3C2410_GPC15_OUTP (0x01 << 30) #define S3C2410_GPC15_VD7 (0x02 << 30) #define S3C2400_GPC15_VD15 (0x02 << 30) @@ -432,99 +300,51 @@ #define S3C2400_GPDDAT S3C2410_GPIOREG(0x24) #define S3C2400_GPDUP S3C2410_GPIOREG(0x28) -#define S3C2410_GPD0 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 0) -#define S3C2410_GPD0_INP (0x00 << 0) -#define S3C2410_GPD0_OUTP (0x01 << 0) #define S3C2410_GPD0_VD8 (0x02 << 0) #define S3C2400_GPD0_VFRAME (0x02 << 0) #define S3C2442_GPD0_nSPICS1 (0x03 << 0) -#define S3C2410_GPD1 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1) -#define S3C2410_GPD1_INP (0x00 << 2) -#define S3C2410_GPD1_OUTP (0x01 << 2) #define S3C2410_GPD1_VD9 (0x02 << 2) #define S3C2400_GPD1_VM (0x02 << 2) #define S3C2442_GPD1_SPICLK1 (0x03 << 2) -#define S3C2410_GPD2 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2) -#define S3C2410_GPD2_INP (0x00 << 4) -#define S3C2410_GPD2_OUTP (0x01 << 4) #define S3C2410_GPD2_VD10 (0x02 << 4) #define S3C2400_GPD2_VLINE (0x02 << 4) -#define S3C2410_GPD3 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 3) -#define S3C2410_GPD3_INP (0x00 << 6) -#define S3C2410_GPD3_OUTP (0x01 << 6) #define S3C2410_GPD3_VD11 (0x02 << 6) #define S3C2400_GPD3_VCLK (0x02 << 6) -#define S3C2410_GPD4 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 4) -#define S3C2410_GPD4_INP (0x00 << 8) -#define S3C2410_GPD4_OUTP (0x01 << 8) #define S3C2410_GPD4_VD12 (0x02 << 8) #define S3C2400_GPD4_LEND (0x02 << 8) -#define S3C2410_GPD5 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 5) -#define S3C2410_GPD5_INP (0x00 << 10) -#define S3C2410_GPD5_OUTP (0x01 << 10) #define S3C2410_GPD5_VD13 (0x02 << 10) #define S3C2400_GPD5_TOUT0 (0x02 << 10) -#define S3C2410_GPD6 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 6) -#define S3C2410_GPD6_INP (0x00 << 12) -#define S3C2410_GPD6_OUTP (0x01 << 12) #define S3C2410_GPD6_VD14 (0x02 << 12) #define S3C2400_GPD6_TOUT1 (0x02 << 12) -#define S3C2410_GPD7 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 7) -#define S3C2410_GPD7_INP (0x00 << 14) -#define S3C2410_GPD7_OUTP (0x01 << 14) #define S3C2410_GPD7_VD15 (0x02 << 14) #define S3C2400_GPD7_TOUT2 (0x02 << 14) -#define S3C2410_GPD8 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 8) -#define S3C2410_GPD8_INP (0x00 << 16) -#define S3C2410_GPD8_OUTP (0x01 << 16) #define S3C2410_GPD8_VD16 (0x02 << 16) #define S3C2400_GPD8_TOUT3 (0x02 << 16) -#define S3C2410_GPD9 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 9) -#define S3C2410_GPD9_INP (0x00 << 18) -#define S3C2410_GPD9_OUTP (0x01 << 18) #define S3C2410_GPD9_VD17 (0x02 << 18) #define S3C2400_GPD9_TCLK0 (0x02 << 18) #define S3C2410_GPD9_MASK (0x03 << 18) -#define S3C2410_GPD10 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 10) -#define S3C2410_GPD10_INP (0x00 << 20) -#define S3C2410_GPD10_OUTP (0x01 << 20) #define S3C2410_GPD10_VD18 (0x02 << 20) #define S3C2400_GPD10_nWAIT (0x02 << 20) -#define S3C2410_GPD11 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 11) -#define S3C2410_GPD11_INP (0x00 << 22) -#define S3C2410_GPD11_OUTP (0x01 << 22) #define S3C2410_GPD11_VD19 (0x02 << 22) -#define S3C2410_GPD12 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 12) -#define S3C2410_GPD12_INP (0x00 << 24) -#define S3C2410_GPD12_OUTP (0x01 << 24) #define S3C2410_GPD12_VD20 (0x02 << 24) -#define S3C2410_GPD13 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 13) -#define S3C2410_GPD13_INP (0x00 << 26) -#define S3C2410_GPD13_OUTP (0x01 << 26) #define S3C2410_GPD13_VD21 (0x02 << 26) -#define S3C2410_GPD14 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 14) -#define S3C2410_GPD14_INP (0x00 << 28) -#define S3C2410_GPD14_OUTP (0x01 << 28) #define S3C2410_GPD14_VD22 (0x02 << 28) #define S3C2410_GPD14_nSS1 (0x03 << 28) -#define S3C2410_GPD15 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 15) -#define S3C2410_GPD15_INP (0x00 << 30) -#define S3C2410_GPD15_OUTP (0x01 << 30) #define S3C2410_GPD15_VD23 (0x02 << 30) #define S3C2410_GPD15_nSS0 (0x03 << 30) @@ -550,34 +370,22 @@ #define S3C2400_GPEDAT S3C2410_GPIOREG(0x30) #define S3C2400_GPEUP S3C2410_GPIOREG(0x34) -#define S3C2410_GPE0 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 0) -#define S3C2410_GPE0_INP (0x00 << 0) -#define S3C2410_GPE0_OUTP (0x01 << 0) #define S3C2410_GPE0_I2SLRCK (0x02 << 0) #define S3C2443_GPE0_AC_nRESET (0x03 << 0) #define S3C2400_GPE0_EINT0 (0x02 << 0) #define S3C2410_GPE0_MASK (0x03 << 0) -#define S3C2410_GPE1 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 1) -#define S3C2410_GPE1_INP (0x00 << 2) -#define S3C2410_GPE1_OUTP (0x01 << 2) #define S3C2410_GPE1_I2SSCLK (0x02 << 2) #define S3C2443_GPE1_AC_SYNC (0x03 << 2) #define S3C2400_GPE1_EINT1 (0x02 << 2) #define S3C2400_GPE1_nSS (0x03 << 2) #define S3C2410_GPE1_MASK (0x03 << 2) -#define S3C2410_GPE2 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 2) -#define S3C2410_GPE2_INP (0x00 << 4) -#define S3C2410_GPE2_OUTP (0x01 << 4) #define S3C2410_GPE2_CDCLK (0x02 << 4) #define S3C2443_GPE2_AC_BITCLK (0x03 << 4) #define S3C2400_GPE2_EINT2 (0x02 << 4) #define S3C2400_GPE2_I2SSDI (0x03 << 4) -#define S3C2410_GPE3 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 3) -#define S3C2410_GPE3_INP (0x00 << 6) -#define S3C2410_GPE3_OUTP (0x01 << 6) #define S3C2410_GPE3_I2SSDI (0x02 << 6) #define S3C2443_GPE3_AC_SDI (0x03 << 6) #define S3C2400_GPE3_EINT3 (0x02 << 6) @@ -585,9 +393,6 @@ #define S3C2410_GPE3_nSS0 (0x03 << 6) #define S3C2410_GPE3_MASK (0x03 << 6) -#define S3C2410_GPE4 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 4) -#define S3C2410_GPE4_INP (0x00 << 8) -#define S3C2410_GPE4_OUTP (0x01 << 8) #define S3C2410_GPE4_I2SSDO (0x02 << 8) #define S3C2443_GPE4_AC_SDO (0x03 << 8) #define S3C2400_GPE4_EINT4 (0x02 << 8) @@ -595,81 +400,48 @@ #define S3C2410_GPE4_I2SSDI (0x03 << 8) #define S3C2410_GPE4_MASK (0x03 << 8) -#define S3C2410_GPE5 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 5) -#define S3C2410_GPE5_INP (0x00 << 10) -#define S3C2410_GPE5_OUTP (0x01 << 10) #define S3C2410_GPE5_SDCLK (0x02 << 10) #define S3C2443_GPE5_SD1_CLK (0x02 << 10) #define S3C2400_GPE5_EINT5 (0x02 << 10) #define S3C2400_GPE5_TCLK1 (0x03 << 10) -#define S3C2410_GPE6 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 6) -#define S3C2410_GPE6_INP (0x00 << 12) -#define S3C2410_GPE6_OUTP (0x01 << 12) #define S3C2410_GPE6_SDCMD (0x02 << 12) #define S3C2443_GPE6_SD1_CMD (0x02 << 12) #define S3C2443_GPE6_AC_BITCLK (0x03 << 12) #define S3C2400_GPE6_EINT6 (0x02 << 12) -#define S3C2410_GPE7 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 7) -#define S3C2410_GPE7_INP (0x00 << 14) -#define S3C2410_GPE7_OUTP (0x01 << 14) #define S3C2410_GPE7_SDDAT0 (0x02 << 14) #define S3C2443_GPE5_SD1_DAT0 (0x02 << 14) #define S3C2443_GPE7_AC_SDI (0x03 << 14) #define S3C2400_GPE7_EINT7 (0x02 << 14) -#define S3C2410_GPE8 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 8) -#define S3C2410_GPE8_INP (0x00 << 16) -#define S3C2410_GPE8_OUTP (0x01 << 16) #define S3C2410_GPE8_SDDAT1 (0x02 << 16) #define S3C2443_GPE8_SD1_DAT1 (0x02 << 16) #define S3C2443_GPE8_AC_SDO (0x03 << 16) #define S3C2400_GPE8_nXDACK0 (0x02 << 16) -#define S3C2410_GPE9 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 9) -#define S3C2410_GPE9_INP (0x00 << 18) -#define S3C2410_GPE9_OUTP (0x01 << 18) #define S3C2410_GPE9_SDDAT2 (0x02 << 18) #define S3C2443_GPE9_SD1_DAT2 (0x02 << 18) #define S3C2443_GPE9_AC_SYNC (0x03 << 18) #define S3C2400_GPE9_nXDACK1 (0x02 << 18) #define S3C2400_GPE9_nXBACK (0x03 << 18) -#define S3C2410_GPE10 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 10) -#define S3C2410_GPE10_INP (0x00 << 20) -#define S3C2410_GPE10_OUTP (0x01 << 20) #define S3C2410_GPE10_SDDAT3 (0x02 << 20) #define S3C2443_GPE10_SD1_DAT3 (0x02 << 20) #define S3C2443_GPE10_AC_nRESET (0x03 << 20) #define S3C2400_GPE10_nXDREQ0 (0x02 << 20) -#define S3C2410_GPE11 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 11) -#define S3C2410_GPE11_INP (0x00 << 22) -#define S3C2410_GPE11_OUTP (0x01 << 22) #define S3C2410_GPE11_SPIMISO0 (0x02 << 22) #define S3C2400_GPE11_nXDREQ1 (0x02 << 22) #define S3C2400_GPE11_nXBREQ (0x03 << 22) -#define S3C2410_GPE12 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 12) -#define S3C2410_GPE12_INP (0x00 << 24) -#define S3C2410_GPE12_OUTP (0x01 << 24) #define S3C2410_GPE12_SPIMOSI0 (0x02 << 24) -#define S3C2410_GPE13 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 13) -#define S3C2410_GPE13_INP (0x00 << 26) -#define S3C2410_GPE13_OUTP (0x01 << 26) #define S3C2410_GPE13_SPICLK0 (0x02 << 26) -#define S3C2410_GPE14 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 14) -#define S3C2410_GPE14_INP (0x00 << 28) -#define S3C2410_GPE14_OUTP (0x01 << 28) #define S3C2410_GPE14_IICSCL (0x02 << 28) #define S3C2410_GPE14_MASK (0x03 << 28) -#define S3C2410_GPE15 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 15) -#define S3C2410_GPE15_INP (0x00 << 30) -#define S3C2410_GPE15_OUTP (0x01 << 30) #define S3C2410_GPE15_IICSDA (0x02 << 30) #define S3C2410_GPE15_MASK (0x03 << 30) @@ -705,55 +477,31 @@ #define S3C2400_GPFDAT S3C2410_GPIOREG(0x3C) #define S3C2400_GPFUP S3C2410_GPIOREG(0x40) -#define S3C2410_GPF0 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 0) -#define S3C2410_GPF0_INP (0x00 << 0) -#define S3C2410_GPF0_OUTP (0x01 << 0) #define S3C2410_GPF0_EINT0 (0x02 << 0) #define S3C2400_GPF0_RXD0 (0x02 << 0) -#define S3C2410_GPF1 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 1) -#define S3C2410_GPF1_INP (0x00 << 2) -#define S3C2410_GPF1_OUTP (0x01 << 2) #define S3C2410_GPF1_EINT1 (0x02 << 2) #define S3C2400_GPF1_RXD1 (0x02 << 2) #define S3C2400_GPF1_IICSDA (0x03 << 2) -#define S3C2410_GPF2 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 2) -#define S3C2410_GPF2_INP (0x00 << 4) -#define S3C2410_GPF2_OUTP (0x01 << 4) #define S3C2410_GPF2_EINT2 (0x02 << 4) #define S3C2400_GPF2_TXD0 (0x02 << 4) -#define S3C2410_GPF3 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 3) -#define S3C2410_GPF3_INP (0x00 << 6) -#define S3C2410_GPF3_OUTP (0x01 << 6) #define S3C2410_GPF3_EINT3 (0x02 << 6) #define S3C2400_GPF3_TXD1 (0x02 << 6) #define S3C2400_GPF3_IICSCL (0x03 << 6) -#define S3C2410_GPF4 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 4) -#define S3C2410_GPF4_INP (0x00 << 8) -#define S3C2410_GPF4_OUTP (0x01 << 8) #define S3C2410_GPF4_EINT4 (0x02 << 8) #define S3C2400_GPF4_nRTS0 (0x02 << 8) #define S3C2400_GPF4_nXBACK (0x03 << 8) -#define S3C2410_GPF5 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 5) -#define S3C2410_GPF5_INP (0x00 << 10) -#define S3C2410_GPF5_OUTP (0x01 << 10) #define S3C2410_GPF5_EINT5 (0x02 << 10) #define S3C2400_GPF5_nCTS0 (0x02 << 10) #define S3C2400_GPF5_nXBREQ (0x03 << 10) -#define S3C2410_GPF6 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 6) -#define S3C2410_GPF6_INP (0x00 << 12) -#define S3C2410_GPF6_OUTP (0x01 << 12) #define S3C2410_GPF6_EINT6 (0x02 << 12) #define S3C2400_GPF6_CLKOUT (0x02 << 12) -#define S3C2410_GPF7 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 7) -#define S3C2410_GPF7_INP (0x00 << 14) -#define S3C2410_GPF7_OUTP (0x01 << 14) #define S3C2410_GPF7_EINT7 (0x02 << 14) #define S3C2410_GPF_PUPDIS(x) (1<<(x)) @@ -778,117 +526,69 @@ #define S3C2400_GPGDAT S3C2410_GPIOREG(0x48) #define S3C2400_GPGUP S3C2410_GPIOREG(0x4C) -#define S3C2410_GPG0 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 0) -#define S3C2410_GPG0_INP (0x00 << 0) -#define S3C2410_GPG0_OUTP (0x01 << 0) #define S3C2410_GPG0_EINT8 (0x02 << 0) #define S3C2400_GPG0_I2SLRCK (0x02 << 0) -#define S3C2410_GPG1 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 1) -#define S3C2410_GPG1_INP (0x00 << 2) -#define S3C2410_GPG1_OUTP (0x01 << 2) #define S3C2410_GPG1_EINT9 (0x02 << 2) #define S3C2400_GPG1_I2SSCLK (0x02 << 2) -#define S3C2410_GPG2 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 2) -#define S3C2410_GPG2_INP (0x00 << 4) -#define S3C2410_GPG2_OUTP (0x01 << 4) #define S3C2410_GPG2_EINT10 (0x02 << 4) #define S3C2410_GPG2_nSS0 (0x03 << 4) #define S3C2400_GPG2_CDCLK (0x02 << 4) -#define S3C2410_GPG3 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 3) -#define S3C2410_GPG3_INP (0x00 << 6) -#define S3C2410_GPG3_OUTP (0x01 << 6) #define S3C2410_GPG3_EINT11 (0x02 << 6) #define S3C2410_GPG3_nSS1 (0x03 << 6) #define S3C2400_GPG3_I2SSDO (0x02 << 6) #define S3C2400_GPG3_I2SSDI (0x03 << 6) -#define S3C2410_GPG4 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 4) -#define S3C2410_GPG4_INP (0x00 << 8) -#define S3C2410_GPG4_OUTP (0x01 << 8) #define S3C2410_GPG4_EINT12 (0x02 << 8) #define S3C2400_GPG4_MMCCLK (0x02 << 8) #define S3C2400_GPG4_I2SSDI (0x03 << 8) #define S3C2410_GPG4_LCDPWREN (0x03 << 8) #define S3C2443_GPG4_LCDPWRDN (0x03 << 8) -#define S3C2410_GPG5 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 5) -#define S3C2410_GPG5_INP (0x00 << 10) -#define S3C2410_GPG5_OUTP (0x01 << 10) #define S3C2410_GPG5_EINT13 (0x02 << 10) #define S3C2400_GPG5_MMCCMD (0x02 << 10) #define S3C2400_GPG5_IICSDA (0x03 << 10) #define S3C2410_GPG5_SPIMISO1 (0x03 << 10) /* not s3c2443 */ -#define S3C2410_GPG6 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 6) -#define S3C2410_GPG6_INP (0x00 << 12) -#define S3C2410_GPG6_OUTP (0x01 << 12) #define S3C2410_GPG6_EINT14 (0x02 << 12) #define S3C2400_GPG6_MMCDAT (0x02 << 12) #define S3C2400_GPG6_IICSCL (0x03 << 12) #define S3C2410_GPG6_SPIMOSI1 (0x03 << 12) -#define S3C2410_GPG7 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 7) -#define S3C2410_GPG7_INP (0x00 << 14) -#define S3C2410_GPG7_OUTP (0x01 << 14) #define S3C2410_GPG7_EINT15 (0x02 << 14) #define S3C2410_GPG7_SPICLK1 (0x03 << 14) #define S3C2400_GPG7_SPIMISO (0x02 << 14) #define S3C2400_GPG7_IICSDA (0x03 << 14) -#define S3C2410_GPG8 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 8) -#define S3C2410_GPG8_INP (0x00 << 16) -#define S3C2410_GPG8_OUTP (0x01 << 16) #define S3C2410_GPG8_EINT16 (0x02 << 16) #define S3C2400_GPG8_SPIMOSI (0x02 << 16) #define S3C2400_GPG8_IICSCL (0x03 << 16) -#define S3C2410_GPG9 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 9) -#define S3C2410_GPG9_INP (0x00 << 18) -#define S3C2410_GPG9_OUTP (0x01 << 18) #define S3C2410_GPG9_EINT17 (0x02 << 18) #define S3C2400_GPG9_SPICLK (0x02 << 18) #define S3C2400_GPG9_MMCCLK (0x03 << 18) -#define S3C2410_GPG10 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 10) -#define S3C2410_GPG10_INP (0x00 << 20) -#define S3C2410_GPG10_OUTP (0x01 << 20) #define S3C2410_GPG10_EINT18 (0x02 << 20) -#define S3C2410_GPG11 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 11) -#define S3C2410_GPG11_INP (0x00 << 22) -#define S3C2410_GPG11_OUTP (0x01 << 22) #define S3C2410_GPG11_EINT19 (0x02 << 22) #define S3C2410_GPG11_TCLK1 (0x03 << 22) #define S3C2443_GPG11_CF_nIREQ (0x03 << 22) -#define S3C2410_GPG12 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 12) -#define S3C2410_GPG12_INP (0x00 << 24) -#define S3C2410_GPG12_OUTP (0x01 << 24) #define S3C2410_GPG12_EINT20 (0x02 << 24) #define S3C2410_GPG12_XMON (0x03 << 24) #define S3C2442_GPG12_nSPICS0 (0x03 << 24) #define S3C2443_GPG12_nINPACK (0x03 << 24) -#define S3C2410_GPG13 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13) -#define S3C2410_GPG13_INP (0x00 << 26) -#define S3C2410_GPG13_OUTP (0x01 << 26) #define S3C2410_GPG13_EINT21 (0x02 << 26) #define S3C2410_GPG13_nXPON (0x03 << 26) #define S3C2443_GPG13_CF_nREG (0x03 << 26) -#define S3C2410_GPG14 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 14) -#define S3C2410_GPG14_INP (0x00 << 28) -#define S3C2410_GPG14_OUTP (0x01 << 28) #define S3C2410_GPG14_EINT22 (0x02 << 28) #define S3C2410_GPG14_YMON (0x03 << 28) #define S3C2443_GPG14_CF_RESET (0x03 << 28) -#define S3C2410_GPG15 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 15) -#define S3C2410_GPG15_INP (0x00 << 30) -#define S3C2410_GPG15_OUTP (0x01 << 30) #define S3C2410_GPG15_EINT23 (0x02 << 30) #define S3C2410_GPG15_nYPON (0x03 << 30) #define S3C2443_GPG15_CF_PWR (0x03 << 30) @@ -907,62 +607,29 @@ #define S3C2410_GPHDAT S3C2410_GPIOREG(0x74) #define S3C2410_GPHUP S3C2410_GPIOREG(0x78) -#define S3C2410_GPH0 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 0) -#define S3C2410_GPH0_INP (0x00 << 0) -#define S3C2410_GPH0_OUTP (0x01 << 0) #define S3C2410_GPH0_nCTS0 (0x02 << 0) -#define S3C2410_GPH1 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 1) -#define S3C2410_GPH1_INP (0x00 << 2) -#define S3C2410_GPH1_OUTP (0x01 << 2) #define S3C2410_GPH1_nRTS0 (0x02 << 2) -#define S3C2410_GPH2 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 2) -#define S3C2410_GPH2_INP (0x00 << 4) -#define S3C2410_GPH2_OUTP (0x01 << 4) #define S3C2410_GPH2_TXD0 (0x02 << 4) -#define S3C2410_GPH3 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 3) -#define S3C2410_GPH3_INP (0x00 << 6) -#define S3C2410_GPH3_OUTP (0x01 << 6) #define S3C2410_GPH3_RXD0 (0x02 << 6) -#define S3C2410_GPH4 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 4) -#define S3C2410_GPH4_INP (0x00 << 8) -#define S3C2410_GPH4_OUTP (0x01 << 8) #define S3C2410_GPH4_TXD1 (0x02 << 8) -#define S3C2410_GPH5 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 5) -#define S3C2410_GPH5_INP (0x00 << 10) -#define S3C2410_GPH5_OUTP (0x01 << 10) #define S3C2410_GPH5_RXD1 (0x02 << 10) -#define S3C2410_GPH6 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 6) -#define S3C2410_GPH6_INP (0x00 << 12) -#define S3C2410_GPH6_OUTP (0x01 << 12) #define S3C2410_GPH6_TXD2 (0x02 << 12) #define S3C2410_GPH6_nRTS1 (0x03 << 12) -#define S3C2410_GPH7 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 7) -#define S3C2410_GPH7_INP (0x00 << 14) -#define S3C2410_GPH7_OUTP (0x01 << 14) #define S3C2410_GPH7_RXD2 (0x02 << 14) #define S3C2410_GPH7_nCTS1 (0x03 << 14) -#define S3C2410_GPH8 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 8) -#define S3C2410_GPH8_INP (0x00 << 16) -#define S3C2410_GPH8_OUTP (0x01 << 16) #define S3C2410_GPH8_UCLK (0x02 << 16) -#define S3C2410_GPH9 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 9) -#define S3C2410_GPH9_INP (0x00 << 18) -#define S3C2410_GPH9_OUTP (0x01 << 18) #define S3C2410_GPH9_CLKOUT0 (0x02 << 18) #define S3C2442_GPH9_nSPICS0 (0x03 << 18) -#define S3C2410_GPH10 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10) -#define S3C2410_GPH10_INP (0x00 << 20) -#define S3C2410_GPH10_OUTP (0x01 << 20) #define S3C2410_GPH10_CLKOUT1 (0x02 << 20) /* The S3C2412 and S3C2413 move the GPJ register set to after diff --git a/arch/arm/mach-s3c2410/include/mach/system-reset.h b/arch/arm/mach-s3c2410/include/mach/system-reset.h index b8687f71c304..6faadcee7729 100644 --- a/arch/arm/mach-s3c2410/include/mach/system-reset.h +++ b/arch/arm/mach-s3c2410/include/mach/system-reset.h @@ -11,21 +11,13 @@ */ #include <mach/hardware.h> -#include <linux/io.h> - -#include <plat/regs-watchdog.h> -#include <mach/regs-clock.h> - -#include <linux/clk.h> -#include <linux/err.h> +#include <plat/watchdog-reset.h> extern void (*s3c24xx_reset_hook)(void); static void arch_reset(char mode, const char *cmd) { - struct clk *wdtclk; - if (mode == 's') { cpu_reset(0); } @@ -33,31 +25,7 @@ arch_reset(char mode, const char *cmd) if (s3c24xx_reset_hook) s3c24xx_reset_hook(); - printk("arch_reset: attempting watchdog reset\n"); - - __raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */ - - wdtclk = clk_get(NULL, "watchdog"); - if (!IS_ERR(wdtclk)) { - clk_enable(wdtclk); - } else - printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__); - - /* put initial values into count and data */ - __raw_writel(0x80, S3C2410_WTCNT); - __raw_writel(0x80, S3C2410_WTDAT); - - /* set the watchdog to go and reset... */ - __raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN | - S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON); - - /* wait for reset to assert... */ - mdelay(500); - - printk(KERN_ERR "Watchdog reset failed to assert reset\n"); - - /* delay to allow the serial port to show the message */ - mdelay(50); + arch_wdt_reset(); /* we'll take a jump through zero as a poor second */ cpu_reset(0); diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c index 6d6995afeb43..06a84adfb13f 100644 --- a/arch/arm/mach-s3c2410/mach-amlm5900.c +++ b/arch/arm/mach-s3c2410/mach-amlm5900.c @@ -32,6 +32,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/device.h> #include <linux/platform_device.h> #include <linux/proc_fs.h> @@ -224,8 +225,8 @@ static void amlm5900_init_pm(void) } else { enable_irq_wake(IRQ_EINT9); /* configure the suspend/resume status pin */ - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); - s3c2410_gpio_pullup(S3C2410_GPF2, 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_pullup(S3C2410_GPF(2), 0); } } static void __init amlm5900_init(void) diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 8637dea5e150..ce3baba2cd7f 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -16,6 +16,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/sysdev.h> #include <linux/serial_core.h> #include <linux/platform_device.h> @@ -212,15 +213,15 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = { static int bast_pm_suspend(struct sys_device *sd, pm_message_t state) { /* ensure that an nRESET is not generated on resume. */ - s3c2410_gpio_setpin(S3C2410_GPA21, 1); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT); + s3c2410_gpio_setpin(S3C2410_GPA(21), 1); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT); return 0; } static int bast_pm_resume(struct sys_device *sd) { - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); return 0; } @@ -591,8 +592,6 @@ static void __init bast_map_io(void) s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc)); s3c24xx_init_clocks(0); s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs)); - - usb_simtec_init(); } static void __init bast_init(void) @@ -607,6 +606,7 @@ static void __init bast_init(void) i2c_register_board_info(0, bast_i2c_devs, ARRAY_SIZE(bast_i2c_devs)); + usb_simtec_init(); nor_simtec_init(); } diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 7a7c4da4c256..d9cd5ddecf4a 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -127,7 +127,7 @@ static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd) static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = { .udc_command = h1940_udc_pullup, - .vbus_pin = S3C2410_GPG5, + .vbus_pin = S3C2410_GPG(5), .vbus_pin_inverted = 1, }; diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index 2b83f8707710..0f6ed61af415 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -19,6 +19,7 @@ #include <linux/gpio_keys.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/input.h> #include <linux/interrupt.h> #include <linux/platform_device.h> @@ -85,10 +86,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) { switch (cmd) { case S3C2410_UDC_P_ENABLE : - s3c2410_gpio_setpin(S3C2410_GPB3, 1); + s3c2410_gpio_setpin(S3C2410_GPB(3), 1); break; case S3C2410_UDC_P_DISABLE : - s3c2410_gpio_setpin(S3C2410_GPB3, 0); + s3c2410_gpio_setpin(S3C2410_GPB(3), 0); break; case S3C2410_UDC_P_RESET : break; @@ -99,55 +100,55 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = { .udc_command = n30_udc_pullup, - .vbus_pin = S3C2410_GPG1, + .vbus_pin = S3C2410_GPG(1), .vbus_pin_inverted = 0, }; static struct gpio_keys_button n30_buttons[] = { { - .gpio = S3C2410_GPF0, + .gpio = S3C2410_GPF(0), .code = KEY_POWER, .desc = "Power", .active_low = 0, }, { - .gpio = S3C2410_GPG9, + .gpio = S3C2410_GPG(9), .code = KEY_UP, .desc = "Thumbwheel Up", .active_low = 0, }, { - .gpio = S3C2410_GPG8, + .gpio = S3C2410_GPG(8), .code = KEY_DOWN, .desc = "Thumbwheel Down", .active_low = 0, }, { - .gpio = S3C2410_GPG7, + .gpio = S3C2410_GPG(7), .code = KEY_ENTER, .desc = "Thumbwheel Press", .active_low = 0, }, { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .code = KEY_HOMEPAGE, .desc = "Home", .active_low = 0, }, { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .code = KEY_CALENDAR, .desc = "Calendar", .active_low = 0, }, { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .code = KEY_ADDRESSBOOK, .desc = "Contacts", .active_low = 0, }, { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .code = KEY_MAIL, .desc = "Mail", .active_low = 0, @@ -169,73 +170,73 @@ static struct platform_device n30_button_device = { static struct gpio_keys_button n35_buttons[] = { { - .gpio = S3C2410_GPF0, + .gpio = S3C2410_GPF(0), .code = KEY_POWER, .desc = "Power", .active_low = 0, }, { - .gpio = S3C2410_GPG9, + .gpio = S3C2410_GPG(9), .code = KEY_UP, .desc = "Joystick Up", .active_low = 0, }, { - .gpio = S3C2410_GPG8, + .gpio = S3C2410_GPG(8), .code = KEY_DOWN, .desc = "Joystick Down", .active_low = 0, }, { - .gpio = S3C2410_GPG6, + .gpio = S3C2410_GPG(6), .code = KEY_DOWN, .desc = "Joystick Left", .active_low = 0, }, { - .gpio = S3C2410_GPG5, + .gpio = S3C2410_GPG(5), .code = KEY_DOWN, .desc = "Joystick Right", .active_low = 0, }, { - .gpio = S3C2410_GPG7, + .gpio = S3C2410_GPG(7), .code = KEY_ENTER, .desc = "Joystick Press", .active_low = 0, }, { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .code = KEY_HOMEPAGE, .desc = "Home", .active_low = 0, }, { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .code = KEY_CALENDAR, .desc = "Calendar", .active_low = 0, }, { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .code = KEY_ADDRESSBOOK, .desc = "Contacts", .active_low = 0, }, { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .code = KEY_MAIL, .desc = "Mail", .active_low = 0, }, { - .gpio = S3C2410_GPF3, + .gpio = S3C2410_GPF(3), .code = SW_RADIO, .desc = "GPS Antenna", .active_low = 0, }, { - .gpio = S3C2410_GPG2, + .gpio = S3C2410_GPG(2), .code = SW_HEADPHONE_INSERT, .desc = "Headphone", .active_low = 0, @@ -259,7 +260,7 @@ static struct platform_device n35_button_device = { /* This is the bluetooth LED on the device. */ static struct s3c24xx_led_platdata n30_blue_led_pdata = { .name = "blue_led", - .gpio = S3C2410_GPG6, + .gpio = S3C2410_GPG(6), .def_trigger = "", }; @@ -270,7 +271,7 @@ static struct s3c24xx_led_platdata n30_blue_led_pdata = { static struct s3c24xx_led_platdata n30_warning_led_pdata = { .name = "warning_led", .flags = S3C24XX_LEDF_ACTLOW, - .gpio = S3C2410_GPD9, + .gpio = S3C2410_GPD(9), .def_trigger = "", }; diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c index 9f1ba9b63f70..2cc9849eb448 100644 --- a/arch/arm/mach-s3c2410/mach-qt2410.c +++ b/arch/arm/mach-s3c2410/mach-qt2410.c @@ -27,6 +27,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/sysdev.h> #include <linux/platform_device.h> #include <linux/serial_core.h> @@ -198,7 +199,7 @@ static struct platform_device qt2410_cs89x0 = { /* LED */ static struct s3c24xx_led_platdata qt2410_pdata_led = { - .gpio = S3C2410_GPB0, + .gpio = S3C2410_GPB(0), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led", .def_trigger = "timer", @@ -218,18 +219,18 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs) { switch (cs) { case BITBANG_CS_ACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB5, 0); + s3c2410_gpio_setpin(S3C2410_GPB(5), 0); break; case BITBANG_CS_INACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB5, 1); + s3c2410_gpio_setpin(S3C2410_GPB(5), 1); break; } } static struct s3c2410_spigpio_info spi_gpio_cfg = { - .pin_clk = S3C2410_GPG7, - .pin_mosi = S3C2410_GPG6, - .pin_miso = S3C2410_GPG5, + .pin_clk = S3C2410_GPG(7), + .pin_mosi = S3C2410_GPG(6), + .pin_miso = S3C2410_GPG(5), .chip_select = &spi_gpio_cs, }; @@ -346,13 +347,13 @@ static void __init qt2410_machine_init(void) } s3c24xx_fb_set_platdata(&qt2410_fb_info); - s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB0, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(0), 1); s3c24xx_udc_set_platdata(&qt2410_udc_cfg); s3c_i2c0_set_platdata(NULL); - s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT); platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices)); s3c_pm_init(); diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 61a1ea9c5c5c..1628cc773a2c 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -18,6 +18,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/dm9000.h> #include <linux/i2c.h> @@ -277,19 +278,19 @@ static struct platform_device vr1000_dm9k1 = { static struct s3c24xx_led_platdata vr1000_led1_pdata = { .name = "led1", - .gpio = S3C2410_GPB0, + .gpio = S3C2410_GPB(0), .def_trigger = "", }; static struct s3c24xx_led_platdata vr1000_led2_pdata = { .name = "led2", - .gpio = S3C2410_GPB1, + .gpio = S3C2410_GPB(1), .def_trigger = "", }; static struct s3c24xx_led_platdata vr1000_led3_pdata = { .name = "led3", - .gpio = S3C2410_GPB2, + .gpio = S3C2410_GPB(2), .def_trigger = "", }; @@ -355,8 +356,8 @@ static struct clk *vr1000_clocks[] __initdata = { static void vr1000_power_off(void) { - s3c2410_gpio_cfgpin(S3C2410_GPB9, S3C2410_GPB9_OUTP); - s3c2410_gpio_setpin(S3C2410_GPB9, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(9), 1); } static void __init vr1000_map_io(void) diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index 87fc481d92d4..143e08a599d4 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -25,6 +25,7 @@ #include <linux/errno.h> #include <linux/time.h> #include <linux/sysdev.h> +#include <linux/gpio.h> #include <linux/io.h> #include <mach/hardware.h> @@ -76,7 +77,7 @@ static void s3c2410_pm_prepare(void) } if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 1); + s3c2410_gpio_setpin(S3C2410_GPF(2), 1); } @@ -91,7 +92,7 @@ static int s3c2410_pm_resume(struct sys_device *dev) __raw_writel(tmp, S3C2410_GSTATUS2); if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); return 0; } diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c index 8331e8d97e20..6cd9377ddb82 100644 --- a/arch/arm/mach-s3c2410/usb-simtec.c +++ b/arch/arm/mach-s3c2410/usb-simtec.c @@ -18,9 +18,11 @@ #include <linux/types.h> #include <linux/interrupt.h> #include <linux/list.h> +#include <linux/gpio.h> #include <linux/timer.h> #include <linux/init.h> #include <linux/device.h> +#include <linux/gpio.h> #include <linux/io.h> #include <asm/mach/arch.h> @@ -29,7 +31,6 @@ #include <mach/bast-map.h> #include <mach/bast-irq.h> -#include <mach/regs-gpio.h> #include <mach/hardware.h> #include <asm/irq.h> @@ -53,9 +54,9 @@ usb_simtec_powercontrol(int port, int to) power_state[port] = to; if (power_state[0] && power_state[1]) - s3c2410_gpio_setpin(S3C2410_GPB4, 0); + gpio_set_value(S3C2410_GPB(4), 0); else - s3c2410_gpio_setpin(S3C2410_GPB4, 1); + gpio_set_value(S3C2410_GPB(4), 1); } static irqreturn_t @@ -63,7 +64,7 @@ usb_simtec_ocirq(int irq, void *pw) { struct s3c2410_hcd_info *info = pw; - if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) { + if (gpio_get_value(S3C2410_GPG(10)) == 0) { pr_debug("usb_simtec: over-current irq (oc detected)\n"); s3c2410_usb_report_oc(info, 3); } else { @@ -106,10 +107,27 @@ static struct s3c2410_hcd_info usb_simtec_info = { int usb_simtec_init(void) { + int ret; + printk("USB Power Control, (c) 2004 Simtec Electronics\n"); - s3c_device_usb.dev.platform_data = &usb_simtec_info; - s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPB4_OUTP); - s3c2410_gpio_setpin(S3C2410_GPB4, 1); + ret = gpio_request(S3C2410_GPB(4), "USB power control"); + if (ret < 0) { + pr_err("%s: failed to get GPB4\n", __func__); + return ret; + } + + ret = gpio_request(S3C2410_GPG(10), "USB overcurrent"); + if (ret < 0) { + pr_err("%s: failed to get GPG10\n", __func__); + gpio_free(S3C2410_GPB(4)); + return ret; + } + + /* turn power on */ + gpio_direction_output(S3C2410_GPB(4), 1); + gpio_direction_input(S3C2410_GPG(10)); + + s3c_device_usb.dev.platform_data = &usb_simtec_info; return 0; } diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index ca99564ae4b5..63586ffd0ae7 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -38,6 +38,7 @@ menu "S3C2412 Machines" config MACH_JIVE bool "Logitech Jive" select CPU_S3C2412 + select S3C_DEV_USB_HOST help Say Y here if you are using the Logitech Jive. @@ -50,6 +51,7 @@ config MACH_SMDK2413 select CPU_S3C2412 select MACH_S3C2413 select MACH_SMDK + select S3C_DEV_USB_HOST help Say Y here if you are using an SMDK2413 @@ -72,6 +74,7 @@ config MACH_SMDK2412 config MACH_VSTMS bool "VMSTMS" select CPU_S3C2412 + select S3C_DEV_USB_HOST help Say Y here if you are using an VSTMS board diff --git a/arch/arm/mach-s3c2412/dma.c b/arch/arm/mach-s3c2412/dma.c index 9e3478506c6f..f8d16fc10bc6 100644 --- a/arch/arm/mach-s3c2412/dma.c +++ b/arch/arm/mach-s3c2412/dma.c @@ -20,12 +20,13 @@ #include <mach/dma.h> -#include <plat/dma.h> +#include <plat/dma-plat.h> #include <plat/cpu.h> #include <plat/regs-serial.h> #include <mach/regs-gpio.h> #include <plat/regs-ac97.h> +#include <plat/regs-dma.h> #include <mach/regs-mem.h> #include <mach/regs-lcd.h> #include <mach/regs-sdi.h> diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c index 8f0d37d43b43..8df506eac903 100644 --- a/arch/arm/mach-s3c2412/mach-jive.c +++ b/arch/arm/mach-s3c2412/mach-jive.c @@ -16,6 +16,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/sysdev.h> #include <linux/serial_core.h> #include <linux/platform_device.h> @@ -356,8 +357,8 @@ static void jive_lcm_reset(unsigned int set) { printk(KERN_DEBUG "%s(%d)\n", __func__, set); - s3c2410_gpio_setpin(S3C2410_GPG13, set); - s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(13), set); + s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT); } #undef LCD_UPPER_MARGIN @@ -390,13 +391,13 @@ static struct ili9320_platdata jive_lcm_config = { static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs) { - s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1); + s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1); } static struct s3c2410_spigpio_info jive_lcd_spi = { .bus_num = 1, - .pin_clk = S3C2410_GPG8, - .pin_mosi = S3C2410_GPB8, + .pin_clk = S3C2410_GPG(8), + .pin_mosi = S3C2410_GPB(8), .num_chipselect = 1, .chip_select = jive_lcd_spi_chipselect, }; @@ -412,13 +413,13 @@ static struct platform_device jive_device_lcdspi = { static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs) { - s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1); + s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1); } static struct s3c2410_spigpio_info jive_wm8750_spi = { .bus_num = 2, - .pin_clk = S3C2410_GPB4, - .pin_mosi = S3C2410_GPB9, + .pin_clk = S3C2410_GPB(4), + .pin_mosi = S3C2410_GPB(9), .num_chipselect = 1, .chip_select = jive_wm8750_chipselect, }; @@ -479,7 +480,7 @@ static struct platform_device *jive_devices[] __initdata = { }; static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = { - .vbus_pin = S3C2410_GPG1, /* detect is on GPG1 */ + .vbus_pin = S3C2410_GPG(1), /* detect is on GPG1 */ }; /* Jive power management device */ @@ -529,8 +530,8 @@ static void jive_power_off(void) { printk(KERN_INFO "powering system down...\n"); - s3c2410_gpio_setpin(S3C2410_GPC5, 1); - s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPC(5), 1); + s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT); } static void __init jive_machine_init(void) @@ -634,22 +635,22 @@ static void __init jive_machine_init(void) /* initialise the spi */ - s3c2410_gpio_setpin(S3C2410_GPG13, 0); - s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(13), 0); + s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB7, 1); - s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(7), 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB6, 0); - s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(6), 0); + s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPG8, 1); - s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(8), 1); + s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT); /* initialise the WM8750 spi */ - s3c2410_gpio_setpin(S3C2410_GPH10, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPH(10), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT); /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c index eba66aa6bd20..9a5e43419722 100644 --- a/arch/arm/mach-s3c2412/mach-smdk2413.c +++ b/arch/arm/mach-s3c2412/mach-smdk2413.c @@ -17,6 +17,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/serial_core.h> #include <linux/platform_device.h> #include <linux/io.h> @@ -84,10 +85,10 @@ static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd) switch (cmd) { case S3C2410_UDC_P_ENABLE : - s3c2410_gpio_setpin(S3C2410_GPF2, 1); + s3c2410_gpio_setpin(S3C2410_GPF(2), 1); break; case S3C2410_UDC_P_DISABLE : - s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); break; case S3C2410_UDC_P_RESET : break; @@ -134,8 +135,8 @@ static void __init smdk2413_machine_init(void) { /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | S3C2410_MISCCR_USBSUSPND0 | diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig index cde5ae9a4340..5df73cbf2b40 100644 --- a/arch/arm/mach-s3c2440/Kconfig +++ b/arch/arm/mach-s3c2440/Kconfig @@ -33,6 +33,7 @@ config MACH_ANUBIS select PM_SIMTEC if PM select HAVE_PATA_PLATFORM select S3C24XX_GPIO_EXTRA64 + select S3C_DEV_USB_HOST help Say Y here if you are using the Simtec Electronics ANUBIS development system @@ -43,6 +44,7 @@ config MACH_OSIRIS select S3C24XX_DCLK select PM_SIMTEC if PM select S3C24XX_GPIO_EXTRA128 + select S3C_DEV_USB_HOST help Say Y here if you are using the Simtec IM2440D20 module, also known as the Osiris. @@ -58,12 +60,14 @@ config ARCH_S3C2440 bool "SMDK2440" select CPU_S3C2440 select MACH_SMDK + select S3C_DEV_USB_HOST help Say Y here if you are using the SMDK2440. config MACH_NEXCODER_2440 bool "NexVision NEXCODER 2440 Light Board" select CPU_S3C2440 + select S3C_DEV_USB_HOST help Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board @@ -76,6 +80,7 @@ config SMDK2440_CPU2440 config MACH_AT2440EVB bool "Avantech AT2440EVB development board" select CPU_S3C2440 + select S3C_DEV_USB_HOST help Say Y here if you are using the AT2440EVB development board diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c index 69b6cf34df47..e08e081430f0 100644 --- a/arch/arm/mach-s3c2440/dma.c +++ b/arch/arm/mach-s3c2440/dma.c @@ -17,14 +17,16 @@ #include <linux/sysdev.h> #include <linux/serial_core.h> +#include <mach/map.h> #include <mach/dma.h> -#include <plat/dma.h> +#include <plat/dma-plat.h> #include <plat/cpu.h> #include <plat/regs-serial.h> #include <mach/regs-gpio.h> #include <plat/regs-ac97.h> +#include <plat/regs-dma.h> #include <mach/regs-mem.h> #include <mach/regs-lcd.h> #include <mach/regs-sdi.h> diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c index 9c6abf9fb540..68f3870991bf 100644 --- a/arch/arm/mach-s3c2440/mach-anubis.c +++ b/arch/arm/mach-s3c2440/mach-anubis.c @@ -15,6 +15,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/serial_core.h> #include <linux/platform_device.h> #include <linux/ata_platform.h> @@ -468,7 +469,7 @@ static void __init anubis_map_io(void) anubis_nand_sets[0].nr_partitions = ARRAY_SIZE(anubis_default_nand_part_large); } else { /* ensure that the GPIO is setup */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); + s3c2410_gpio_setpin(S3C2410_GPA(0), 1); } } diff --git a/arch/arm/mach-s3c2440/mach-at2440evb.c b/arch/arm/mach-s3c2440/mach-at2440evb.c index 315c42e31278..dfc7010935da 100644 --- a/arch/arm/mach-s3c2440/mach-at2440evb.c +++ b/arch/arm/mach-s3c2440/mach-at2440evb.c @@ -166,7 +166,7 @@ static struct platform_device at2440evb_device_eth = { }; static struct s3c24xx_mci_pdata at2440evb_mci_pdata = { - .gpio_detect = S3C2410_GPG10, + .gpio_detect = S3C2410_GPG(10), }; /* 7" LCD panel */ diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c index 7aeaa972d7f5..d43edede590e 100644 --- a/arch/arm/mach-s3c2440/mach-nexcoder.c +++ b/arch/arm/mach-s3c2440/mach-nexcoder.c @@ -18,6 +18,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/string.h> #include <linux/serial_core.h> #include <linux/platform_device.h> @@ -120,16 +121,16 @@ static struct platform_device *nexcoder_devices[] __initdata = { static void __init nexcoder_sensorboard_init(void) { // Initialize SCCB bus - s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL - s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_OUTP); - s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA - s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_OUTP); + s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL + s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA + s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT); // Power up the sensor board - s3c2410_gpio_setpin(S3C2410_GPF1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPF1_OUTP); // CAM_GPIO7 => nLDO_PWRDN - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); // CAM_GPIO6 => CAM_PWRDN + s3c2410_gpio_setpin(S3C2410_GPF(1), 1); + s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN } static void __init nexcoder_map_io(void) diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c index c8a46685ce38..cba064b49a64 100644 --- a/arch/arm/mach-s3c2440/mach-osiris.c +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -15,6 +15,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/device.h> #include <linux/sysdev.h> #include <linux/serial_core.h> @@ -291,8 +292,8 @@ static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state) __raw_writeb(tmp, OSIRIS_VA_CTRL0); /* ensure that an nRESET is not generated on resume. */ - s3c2410_gpio_setpin(S3C2410_GPA21, 1); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT); + s3c2410_gpio_setpin(S3C2410_GPA(21), 1); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT); return 0; } @@ -304,7 +305,7 @@ static int osiris_pm_resume(struct sys_device *sd) __raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); return 0; } @@ -384,7 +385,7 @@ static void __init osiris_map_io(void) osiris_nand_sets[0].nr_partitions = ARRAY_SIZE(osiris_default_nand_part_large); } else { /* write-protect line to the NAND */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); + s3c2410_gpio_setpin(S3C2410_GPA(0), 1); } /* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */ diff --git a/arch/arm/mach-s3c2443/dma.c b/arch/arm/mach-s3c2443/dma.c index 8430e5829186..397f3b5c0b47 100644 --- a/arch/arm/mach-s3c2443/dma.c +++ b/arch/arm/mach-s3c2443/dma.c @@ -20,12 +20,13 @@ #include <mach/dma.h> -#include <plat/dma.h> +#include <plat/dma-plat.h> #include <plat/cpu.h> #include <plat/regs-serial.h> #include <mach/regs-gpio.h> #include <plat/regs-ac97.h> +#include <plat/regs-dma.h> #include <mach/regs-mem.h> #include <mach/regs-lcd.h> #include <mach/regs-sdi.h> diff --git a/arch/arm/mach-s3c6400/Kconfig b/arch/arm/mach-s3c6400/Kconfig index 6da82b5c09ba..f5af212066c3 100644 --- a/arch/arm/mach-s3c6400/Kconfig +++ b/arch/arm/mach-s3c6400/Kconfig @@ -5,4 +5,27 @@ # # Licensed under GPLv2 -# Currently nothing here, this will be added later +# Configuration options for the S3C6410 CPU + +config CPU_S3C6400 + bool + select CPU_S3C6400_INIT + select CPU_S3C6400_CLOCK + help + Enable S3C6400 CPU support + +config S3C6400_SETUP_SDHCI + bool + help + Internal configuration for default SDHCI + setup for S3C6400. + +# S36400 Macchine support + +config MACH_SMDK6400 + bool "SMDK6400" + select CPU_S3C6400 + select S3C_DEV_HSMMC + select S3C6400_SETUP_SDHCI + help + Machine support for the Samsung SMDK6400 diff --git a/arch/arm/mach-s3c6400/Makefile b/arch/arm/mach-s3c6400/Makefile index 8f397db25b87..df1ce4aa03e5 100644 --- a/arch/arm/mach-s3c6400/Makefile +++ b/arch/arm/mach-s3c6400/Makefile @@ -12,4 +12,12 @@ obj- := # Core support for S3C6400 system -obj-n += blank.o +obj-$(CONFIG_CPU_S3C6400) += s3c6400.o + +# setup support + +obj-$(CONFIG_S3C6400_SETUP_SDHCI) += setup-sdhci.o + +# Machine support + +obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o diff --git a/arch/arm/mach-s3c6400/include/mach/dma.h b/arch/arm/mach-s3c6400/include/mach/dma.h index 9771ac2cb07e..1067619f0ba0 100644 --- a/arch/arm/mach-s3c6400/include/mach/dma.h +++ b/arch/arm/mach-s3c6400/include/mach/dma.h @@ -11,6 +11,63 @@ #ifndef __ASM_ARCH_DMA_H #define __ASM_ARCH_DMA_H __FILE__ -/* currently nothing here, placeholder */ +#define S3C_DMA_CHANNELS (16) + +/* see mach-s3c2410/dma.h for notes on dma channel numbers */ + +/* Note, for the S3C64XX architecture we keep the DMACH_ + * defines in the order they are allocated to [S]DMA0/[S]DMA1 + * so that is easy to do DHACH_ -> DMA controller conversion + */ +enum dma_ch { + /* DMA0/SDMA0 */ + DMACH_UART0 = 0, + DMACH_UART0_SRC2, + DMACH_UART1, + DMACH_UART1_SRC2, + DMACH_UART2, + DMACH_UART2_SRC2, + DMACH_UART3, + DMACH_UART3_SRC2, + DMACH_PCM0_TX, + DMACH_PCM0_RX, + DMACH_I2S0_OUT, + DMACH_I2S0_IN, + DMACH_SPI0_TX, + DMACH_SPI0_RX, + DMACH_HSI_I2SV40_TX, + DMACH_HSI_I2SV40_RX, + + /* DMA1/SDMA1 */ + DMACH_PCM1_TX = 16, + DMACH_PCM1_RX, + DMACH_I2S1_OUT, + DMACH_I2S1_IN, + DMACH_SPI1_TX, + DMACH_SPI1_RX, + DMACH_AC97_PCMOUT, + DMACH_AC97_PCMIN, + DMACH_AC97_MICIN, + DMACH_PWM, + DMACH_IRDA, + DMACH_EXTERNAL, + DMACH_RES1, + DMACH_RES2, + DMACH_SECURITY_RX, /* SDMA1 only */ + DMACH_SECURITY_TX, /* SDMA1 only */ + DMACH_MAX /* the end */ +}; + +static __inline__ int s3c_dma_has_circular(void) +{ + /* we will be supporting ciruclar buffers as soon as we have DMA + * engine support. + */ + return 1; +} + +#define S3C2410_DMAF_CIRCULAR (1 << 0) + +#include <plat/dma.h> #endif /* __ASM_ARCH_IRQ_H */ diff --git a/arch/arm/mach-s3c6400/include/mach/map.h b/arch/arm/mach-s3c6400/include/mach/map.h index 8199972ed5bd..5057d9948d35 100644 --- a/arch/arm/mach-s3c6400/include/mach/map.h +++ b/arch/arm/mach-s3c6400/include/mach/map.h @@ -39,6 +39,8 @@ #define S3C_VA_UART3 S3C_VA_UARTx(3) #define S3C64XX_PA_FB (0x77100000) +#define S3C64XX_PA_USB_HSOTG (0x7C000000) +#define S3C64XX_PA_WATCHDOG (0x7E004000) #define S3C64XX_PA_SYSCON (0x7E00F000) #define S3C64XX_PA_IIS0 (0x7F002000) #define S3C64XX_PA_IIS1 (0x7F003000) @@ -57,6 +59,8 @@ #define S3C64XX_PA_MODEM (0x74108000) #define S3C64XX_VA_MODEM S3C_ADDR(0x00600000) +#define S3C64XX_PA_USBHOST (0x74300000) + /* place VICs close together */ #define S3C_VA_VIC0 (S3C_VA_IRQ + 0x00) #define S3C_VA_VIC1 (S3C_VA_IRQ + 0x10000) @@ -69,5 +73,7 @@ #define S3C_PA_IIC S3C64XX_PA_IIC0 #define S3C_PA_IIC1 S3C64XX_PA_IIC1 #define S3C_PA_FB S3C64XX_PA_FB +#define S3C_PA_USBHOST S3C64XX_PA_USBHOST +#define S3C_PA_USB_HSOTG S3C64XX_PA_USB_HSOTG #endif /* __ASM_ARCH_6400_MAP_H */ diff --git a/arch/arm/mach-s3c6400/include/mach/regs-clock.h b/arch/arm/mach-s3c6400/include/mach/regs-clock.h new file mode 100644 index 000000000000..a6c7f4eb3a1b --- /dev/null +++ b/arch/arm/mach-s3c6400/include/mach/regs-clock.h @@ -0,0 +1,16 @@ +/* linux/arch/arm/mach-s3c6400/include/mach/regs-clock.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C64XX - clock register compatibility with s3c24xx + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <plat/regs-clock.h> + diff --git a/arch/arm/mach-s3c6400/include/mach/system.h b/arch/arm/mach-s3c6400/include/mach/system.h index 090cfd969bc7..2e58cb7a7147 100644 --- a/arch/arm/mach-s3c6400/include/mach/system.h +++ b/arch/arm/mach-s3c6400/include/mach/system.h @@ -11,6 +11,8 @@ #ifndef __ASM_ARCH_SYSTEM_H #define __ASM_ARCH_SYSTEM_H __FILE__ +#include <plat/watchdog-reset.h> + static void arch_idle(void) { /* nothing here yet */ @@ -18,7 +20,11 @@ static void arch_idle(void) static void arch_reset(char mode, const char *cmd) { - /* nothing here yet */ + if (mode != 's') + arch_wdt_reset(); + + /* if all else fails, or mode was for soft, jump to 0 */ + cpu_reset(0); } #endif /* __ASM_ARCH_IRQ_H */ diff --git a/arch/arm/mach-s3c6400/mach-smdk6400.c b/arch/arm/mach-s3c6400/mach-smdk6400.c new file mode 100644 index 000000000000..ab19285389a7 --- /dev/null +++ b/arch/arm/mach-s3c6400/mach-smdk6400.c @@ -0,0 +1,96 @@ +/* linux/arch/arm/mach-s3c6400/mach-smdk6400.c + * + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/serial_core.h> +#include <linux/platform_device.h> +#include <linux/i2c.h> +#include <linux/io.h> + +#include <asm/mach-types.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <mach/map.h> + +#include <plat/regs-serial.h> + +#include <plat/s3c6400.h> +#include <plat/clock.h> +#include <plat/devs.h> +#include <plat/cpu.h> +#include <plat/iic.h> + +#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg smdk6400_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, +}; + +static struct map_desc smdk6400_iodesc[] = {}; + +static void __init smdk6400_map_io(void) +{ + s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs)); +} + +static struct platform_device *smdk6400_devices[] __initdata = { + &s3c_device_hsmmc1, + &s3c_device_i2c0, +}; + +static struct i2c_board_info i2c_devs[] __initdata = { + { I2C_BOARD_INFO("wm8753", 0x1A), }, + { I2C_BOARD_INFO("24c08", 0x50), }, +}; + +static void __init smdk6400_machine_init(void) +{ + i2c_register_board_info(0, i2c_devs, ARRAY_SIZE(i2c_devs)); + platform_add_devices(smdk6400_devices, ARRAY_SIZE(smdk6400_devices)); +} + +MACHINE_START(SMDK6400, "SMDK6400") + /* Maintainer: Ben Dooks <ben@fluff.org> */ + .phys_io = S3C_PA_UART & 0xfff00000, + .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C64XX_PA_SDRAM + 0x100, + + .init_irq = s3c6400_init_irq, + .map_io = smdk6400_map_io, + .init_machine = smdk6400_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c6400/s3c6400.c b/arch/arm/mach-s3c6400/s3c6400.c new file mode 100644 index 000000000000..1ece887d90bb --- /dev/null +++ b/arch/arm/mach-s3c6400/s3c6400.c @@ -0,0 +1,89 @@ +/* linux/arch/arm/mach-s3c6410/cpu.c + * + * Copyright 2009 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/sysdev.h> +#include <linux/serial_core.h> +#include <linux/platform_device.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <asm/irq.h> + +#include <plat/cpu-freq.h> +#include <plat/regs-serial.h> +#include <plat/regs-clock.h> + +#include <plat/cpu.h> +#include <plat/devs.h> +#include <plat/clock.h> +#include <plat/sdhci.h> +#include <plat/iic-core.h> +#include <plat/s3c6400.h> + +void __init s3c6400_map_io(void) +{ + /* setup SDHCI */ + + s3c6400_default_sdhci0(); + s3c6400_default_sdhci1(); + + /* the i2c devices are directly compatible with s3c2440 */ + s3c_i2c0_setname("s3c2440-i2c"); +} + +void __init s3c6400_init_clocks(int xtal) +{ + printk(KERN_DEBUG "%s: initialising clocks\n", __func__); + s3c24xx_register_baseclocks(xtal); + s3c64xx_register_clocks(); + s3c6400_register_clocks(S3C6400_CLKDIV0_ARM_MASK); + s3c6400_setup_clocks(); +} + +void __init s3c6400_init_irq(void) +{ + /* VIC0 does not have IRQS 5..7, + * VIC1 is fully populated. */ + s3c64xx_init_irq(~0 & ~(0xf << 5), ~0); +} + +struct sysdev_class s3c6400_sysclass = { + .name = "s3c6400-core", +}; + +static struct sys_device s3c6400_sysdev = { + .cls = &s3c6400_sysclass, +}; + +static int __init s3c6400_core_init(void) +{ + return sysdev_class_register(&s3c6400_sysclass); +} + +core_initcall(s3c6400_core_init); + +int __init s3c6400_init(void) +{ + printk("S3C6400: Initialising architecture\n"); + + return sysdev_register(&s3c6400_sysdev); +} diff --git a/arch/arm/mach-s3c6400/setup-sdhci.c b/arch/arm/mach-s3c6400/setup-sdhci.c new file mode 100644 index 000000000000..b93dafbee1f4 --- /dev/null +++ b/arch/arm/mach-s3c6400/setup-sdhci.c @@ -0,0 +1,63 @@ +/* linux/arch/arm/mach-s3c6410/setup-sdhci.c + * + * Copyright 2008 Simtec Electronics + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C6410 - Helper functions for settign up SDHCI device(s) (HSMMC) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/io.h> + +#include <linux/mmc/card.h> +#include <linux/mmc/host.h> + +#include <plat/regs-sdhci.h> +#include <plat/sdhci.h> + +/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */ + +char *s3c6400_hsmmc_clksrcs[4] = { + [0] = "hsmmc", + [1] = "hsmmc", + [2] = "mmc_bus", + /* [3] = "48m", - note not succesfully used yet */ +}; + +void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev, + void __iomem *r, + struct mmc_ios *ios, + struct mmc_card *card) +{ + u32 ctrl2, ctrl3; + + ctrl2 = readl(r + S3C_SDHCI_CONTROL2); + ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK; + ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR | + S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK | + S3C_SDHCI_CTRL2_ENFBCLKRX | + S3C_SDHCI_CTRL2_DFCNT_NONE | + S3C_SDHCI_CTRL2_ENCLKOUTHOLD); + + if (ios->clock < 25 * 1000000) + ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 | + S3C_SDHCI_CTRL3_FCSEL2 | + S3C_SDHCI_CTRL3_FCSEL1 | + S3C_SDHCI_CTRL3_FCSEL0); + else + ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0); + + printk(KERN_INFO "%s: CTRL 2=%08x, 3=%08x\n", __func__, ctrl2, ctrl3); + writel(ctrl2, r + S3C_SDHCI_CONTROL2); + writel(ctrl3, r + S3C_SDHCI_CONTROL3); +} + diff --git a/arch/arm/mach-s3c6410/Kconfig b/arch/arm/mach-s3c6410/Kconfig index 1d5010070027..e63aac7f4e5a 100644 --- a/arch/arm/mach-s3c6410/Kconfig +++ b/arch/arm/mach-s3c6410/Kconfig @@ -16,9 +16,18 @@ config CPU_S3C6410 config S3C6410_SETUP_SDHCI bool + select S3C64XX_SETUP_SDHCI_GPIO help Internal helper functions for S3C6410 based SDHCI systems +config MACH_ANW6410 + bool "A&W6410" + select CPU_S3C6410 + select S3C_DEV_FB + select S3C64XX_SETUP_FB_24BPP + help + Machine support for the A&W6410 + config MACH_SMDK6410 bool "SMDK6410" select CPU_S3C6410 @@ -26,6 +35,8 @@ config MACH_SMDK6410 select S3C_DEV_HSMMC1 select S3C_DEV_I2C1 select S3C_DEV_FB + select S3C_DEV_USB_HOST + select S3C_DEV_USB_HSOTG select S3C6410_SETUP_SDHCI select S3C64XX_SETUP_I2C1 select S3C64XX_SETUP_FB_24BPP @@ -60,3 +71,29 @@ config SMDK6410_SD_CH1 channels 0 and 1 are the same. endchoice + +config SMDK6410_WM1190_EV1 + bool "Support Wolfson Microelectronics 1190-EV1 PMIC card" + depends on MACH_SMDK6410 + select REGULATOR + select REGULATOR_WM8350 + select MFD_WM8350_I2C + select MFD_WM8350_CONFIG_MODE_0 + select MFD_WM8350_CONFIG_MODE_3 + select MFD_WM8352_CONFIG_MODE_0 + help + The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC + and audio daughtercard for the Samsung SMDK6410 reference + platform. Enabling this option will build support for this + module into the kernel. The presence of the module will be + detected at runtime so the the resulting kernel can be used + with or without the 1190-EV1 fitted. + +config MACH_NCP + bool "NCP" + select CPU_S3C6410 + select S3C_DEV_I2C1 + select S3C_DEV_HSMMC1 + select S3C64XX_SETUP_I2C1 + help + Machine support for the Samsung NCP diff --git a/arch/arm/mach-s3c6410/Makefile b/arch/arm/mach-s3c6410/Makefile index 2cd4f189036b..6f9deac88612 100644 --- a/arch/arm/mach-s3c6410/Makefile +++ b/arch/arm/mach-s3c6410/Makefile @@ -20,4 +20,8 @@ obj-$(CONFIG_S3C6410_SETUP_SDHCI) += setup-sdhci.o # machine support +obj-$(CONFIG_MACH_ANW6410) += mach-anw6410.o obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o +obj-$(CONFIG_MACH_NCP) += mach-ncp.o + + diff --git a/arch/arm/mach-s3c6410/cpu.c b/arch/arm/mach-s3c6410/cpu.c index 6a73ca6b7a3a..ade904de8895 100644 --- a/arch/arm/mach-s3c6410/cpu.c +++ b/arch/arm/mach-s3c6410/cpu.c @@ -31,6 +31,7 @@ #include <plat/cpu-freq.h> #include <plat/regs-serial.h> +#include <plat/regs-clock.h> #include <plat/cpu.h> #include <plat/devs.h> @@ -68,7 +69,7 @@ void __init s3c6410_init_clocks(int xtal) printk(KERN_DEBUG "%s: initialising clocks\n", __func__); s3c24xx_register_baseclocks(xtal); s3c64xx_register_clocks(); - s3c6400_register_clocks(); + s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK); s3c6400_setup_clocks(); } diff --git a/arch/arm/mach-s3c6410/mach-anw6410.c b/arch/arm/mach-s3c6410/mach-anw6410.c new file mode 100644 index 000000000000..661cca63de25 --- /dev/null +++ b/arch/arm/mach-s3c6410/mach-anw6410.c @@ -0,0 +1,245 @@ +/* linux/arch/arm/mach-s3c6410/mach-anw6410.c + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * Copyright 2009 Kwangwoo Lee + * Kwangwoo Lee <kwangwoo.lee@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/serial_core.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/i2c.h> +#include <linux/fb.h> +#include <linux/gpio.h> +#include <linux/delay.h> +#include <linux/dm9000.h> + +#include <video/platform_lcd.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <mach/regs-fb.h> +#include <mach/map.h> + +#include <asm/irq.h> +#include <asm/mach-types.h> + +#include <plat/regs-serial.h> +#include <plat/iic.h> +#include <plat/fb.h> + +#include <plat/s3c6410.h> +#include <plat/clock.h> +#include <plat/devs.h> +#include <plat/cpu.h> +#include <plat/regs-gpio.h> +#include <plat/regs-modem.h> + +/* DM9000 */ +#define ANW6410_PA_DM9000 (0x18000000) + +/* A hardware buffer to control external devices is mapped at 0x30000000. + * It can not be read. So current status must be kept in anw6410_extdev_status. + */ +#define ANW6410_VA_EXTDEV S3C_ADDR(0x02000000) +#define ANW6410_PA_EXTDEV (0x30000000) + +#define ANW6410_EN_DM9000 (1<<11) +#define ANW6410_EN_LCD (1<<14) + +static __u32 anw6410_extdev_status; + +static struct s3c2410_uartcfg anw6410_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, +}; + +/* framebuffer and LCD setup. */ +static void __init anw6410_lcd_mode_set(void) +{ + u32 tmp; + + /* set the LCD type */ + tmp = __raw_readl(S3C64XX_SPCON); + tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK; + tmp |= S3C64XX_SPCON_LCD_SEL_RGB; + __raw_writel(tmp, S3C64XX_SPCON); + + /* remove the LCD bypass */ + tmp = __raw_readl(S3C64XX_MODEM_MIFPCON); + tmp &= ~MIFPCON_LCD_BYPASS; + __raw_writel(tmp, S3C64XX_MODEM_MIFPCON); +} + +/* GPF1 = LCD panel power + * GPF4 = LCD backlight control + */ +static void anw6410_lcd_power_set(struct plat_lcd_data *pd, + unsigned int power) +{ + if (power) { + anw6410_extdev_status |= (ANW6410_EN_LCD << 16); + __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV); + + gpio_direction_output(S3C64XX_GPF(1), 1); + gpio_direction_output(S3C64XX_GPF(4), 1); + } else { + anw6410_extdev_status &= ~(ANW6410_EN_LCD << 16); + __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV); + + gpio_direction_output(S3C64XX_GPF(1), 0); + gpio_direction_output(S3C64XX_GPF(4), 0); + } +} + +static struct plat_lcd_data anw6410_lcd_power_data = { + .set_power = anw6410_lcd_power_set, +}; + +static struct platform_device anw6410_lcd_powerdev = { + .name = "platform-lcd", + .dev.parent = &s3c_device_fb.dev, + .dev.platform_data = &anw6410_lcd_power_data, +}; + +static struct s3c_fb_pd_win anw6410_fb_win0 = { + /* this is to ensure we use win0 */ + .win_mode = { + .pixclock = 41094, + .left_margin = 8, + .right_margin = 13, + .upper_margin = 7, + .lower_margin = 5, + .hsync_len = 3, + .vsync_len = 1, + .xres = 800, + .yres = 480, + }, + .max_bpp = 32, + .default_bpp = 16, +}; + +/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */ +static struct s3c_fb_platdata anw6410_lcd_pdata __initdata = { + .setup_gpio = s3c64xx_fb_gpio_setup_24bpp, + .win[0] = &anw6410_fb_win0, + .vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB, + .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC, +}; + +/* DM9000AEP 10/100 ethernet controller */ +static void __init anw6410_dm9000_enable(void) +{ + anw6410_extdev_status |= (ANW6410_EN_DM9000 << 16); + __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV); +} + +static struct resource anw6410_dm9000_resource[] = { + [0] = { + .start = ANW6410_PA_DM9000, + .end = ANW6410_PA_DM9000 + 3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = ANW6410_PA_DM9000 + 4, + .end = ANW6410_PA_DM9000 + 4 + 500, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_EINT(15), + .end = IRQ_EINT(15), + .flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH, + }, +}; + +static struct dm9000_plat_data anw6410_dm9000_pdata = { + .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM), + /* dev_addr can be set to provide hwaddr. */ +}; + +static struct platform_device anw6410_device_eth = { + .name = "dm9000", + .id = -1, + .num_resources = ARRAY_SIZE(anw6410_dm9000_resource), + .resource = anw6410_dm9000_resource, + .dev = { + .platform_data = &anw6410_dm9000_pdata, + }, +}; + +static struct map_desc anw6410_iodesc[] __initdata = { + { + .virtual = (unsigned long)ANW6410_VA_EXTDEV, + .pfn = __phys_to_pfn(ANW6410_PA_EXTDEV), + .length = SZ_64K, + .type = MT_DEVICE, + }, +}; + +static struct platform_device *anw6410_devices[] __initdata = { + &s3c_device_fb, + &anw6410_lcd_powerdev, + &anw6410_device_eth, +}; + +static void __init anw6410_map_io(void) +{ + s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs)); + + anw6410_lcd_mode_set(); +} + +static void __init anw6410_machine_init(void) +{ + s3c_fb_set_platdata(&anw6410_lcd_pdata); + + gpio_request(S3C64XX_GPF(1), "panel power"); + gpio_request(S3C64XX_GPF(4), "LCD backlight"); + + anw6410_dm9000_enable(); + + platform_add_devices(anw6410_devices, ARRAY_SIZE(anw6410_devices)); +} + +MACHINE_START(ANW6410, "A&W6410") + /* Maintainer: Kwangwoo Lee <kwangwoo.lee@gmail.com> */ + .phys_io = S3C_PA_UART & 0xfff00000, + .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C64XX_PA_SDRAM + 0x100, + + .init_irq = s3c6410_init_irq, + .map_io = anw6410_map_io, + .init_machine = anw6410_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c6410/mach-ncp.c b/arch/arm/mach-s3c6410/mach-ncp.c new file mode 100644 index 000000000000..6030636f8548 --- /dev/null +++ b/arch/arm/mach-s3c6410/mach-ncp.c @@ -0,0 +1,107 @@ +/* + * linux/arch/arm/mach-s3c6410/mach-ncp.c + * + * Copyright (C) 2008-2009 Samsung Electronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/serial_core.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/i2c.h> +#include <linux/fb.h> +#include <linux/gpio.h> +#include <linux/delay.h> + +#include <video/platform_lcd.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <mach/regs-fb.h> +#include <mach/map.h> + +#include <asm/irq.h> +#include <asm/mach-types.h> + +#include <plat/regs-serial.h> +#include <plat/iic.h> +#include <plat/fb.h> + +#include <plat/s3c6410.h> +#include <plat/clock.h> +#include <plat/devs.h> +#include <plat/cpu.h> + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg ncp_uartcfgs[] __initdata = { + /* REVISIT: NCP uses only serial 1, 2 */ + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, +}; + +static struct platform_device *ncp_devices[] __initdata = { + &s3c_device_hsmmc1, + &s3c_device_i2c0, +}; + +struct map_desc ncp_iodesc[] = {}; + +static void __init ncp_map_io(void) +{ + s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs)); +} + +static void __init ncp_machine_init(void) +{ + s3c_i2c0_set_platdata(NULL); + + platform_add_devices(ncp_devices, ARRAY_SIZE(ncp_devices)); +} + +MACHINE_START(NCP, "NCP") + /* Maintainer: Samsung Electronics */ + .phys_io = S3C_PA_UART & 0xfff00000, + .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C64XX_PA_SDRAM + 0x100, + .init_irq = s3c6410_init_irq, + .map_io = ncp_map_io, + .init_machine = ncp_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index 7f473e47e4f1..bc9a7dea567f 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -24,6 +24,12 @@ #include <linux/fb.h> #include <linux/gpio.h> #include <linux/delay.h> +#include <linux/smsc911x.h> + +#ifdef CONFIG_SMDK6410_WM1190_EV1 +#include <linux/mfd/wm8350/core.h> +#include <linux/mfd/wm8350/pmic.h> +#endif #include <video/platform_lcd.h> @@ -39,8 +45,12 @@ #include <asm/mach-types.h> #include <plat/regs-serial.h> +#include <plat/regs-modem.h> +#include <plat/regs-gpio.h> +#include <plat/regs-sys.h> #include <plat/iic.h> #include <plat/fb.h> +#include <plat/gpio-cfg.h> #include <plat/s3c6410.h> #include <plat/clock.h> @@ -129,6 +139,37 @@ static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = { .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC, }; +static struct resource smdk6410_smsc911x_resources[] = { + [0] = { + .start = 0x18000000, + .end = 0x18000000 + SZ_64K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = S3C_EINT(10), + .end = S3C_EINT(10), + .flags = IORESOURCE_IRQ | IRQ_TYPE_LEVEL_LOW, + }, +}; + +static struct smsc911x_platform_config smdk6410_smsc911x_pdata = { + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + + +static struct platform_device smdk6410_smsc911x = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smdk6410_smsc911x_resources), + .resource = &smdk6410_smsc911x_resources[0], + .dev = { + .platform_data = &smdk6410_smsc911x_pdata, + }, +}; + static struct map_desc smdk6410_iodesc[] = {}; static struct platform_device *smdk6410_devices[] __initdata = { @@ -141,12 +182,155 @@ static struct platform_device *smdk6410_devices[] __initdata = { &s3c_device_i2c0, &s3c_device_i2c1, &s3c_device_fb, + &s3c_device_usb, + &s3c_device_usb_hsotg, &smdk6410_lcd_powerdev, + + &smdk6410_smsc911x, +}; + +#ifdef CONFIG_SMDK6410_WM1190_EV1 +/* S3C64xx internal logic & PLL */ +static struct regulator_init_data wm8350_dcdc1_data = { + .constraints = { + .name = "PVDD_INT/PVDD_PLL", + .min_uV = 1200000, + .max_uV = 1200000, + .always_on = 1, + .apply_uV = 1, + }, +}; + +/* Memory */ +static struct regulator_init_data wm8350_dcdc3_data = { + .constraints = { + .name = "PVDD_MEM", + .min_uV = 1800000, + .max_uV = 1800000, + .always_on = 1, + .state_mem = { + .uV = 1800000, + .mode = REGULATOR_MODE_NORMAL, + .enabled = 1, + }, + .initial_state = PM_SUSPEND_MEM, + }, +}; + +/* USB, EXT, PCM, ADC/DAC, USB, MMC */ +static struct regulator_init_data wm8350_dcdc4_data = { + .constraints = { + .name = "PVDD_HI/PVDD_EXT/PVDD_SYS/PVCCM2MTV", + .min_uV = 3000000, + .max_uV = 3000000, + .always_on = 1, + }, +}; + +/* ARM core */ +static struct regulator_consumer_supply dcdc6_consumers[] = { + { + .supply = "vddarm", + } +}; + +static struct regulator_init_data wm8350_dcdc6_data = { + .constraints = { + .name = "PVDD_ARM", + .min_uV = 1000000, + .max_uV = 1300000, + .always_on = 1, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + }, + .num_consumer_supplies = ARRAY_SIZE(dcdc6_consumers), + .consumer_supplies = dcdc6_consumers, }; +/* Alive */ +static struct regulator_init_data wm8350_ldo1_data = { + .constraints = { + .name = "PVDD_ALIVE", + .min_uV = 1200000, + .max_uV = 1200000, + .always_on = 1, + .apply_uV = 1, + }, +}; + +/* OTG */ +static struct regulator_init_data wm8350_ldo2_data = { + .constraints = { + .name = "PVDD_OTG", + .min_uV = 3300000, + .max_uV = 3300000, + .always_on = 1, + }, +}; + +/* LCD */ +static struct regulator_init_data wm8350_ldo3_data = { + .constraints = { + .name = "PVDD_LCD", + .min_uV = 3000000, + .max_uV = 3000000, + .always_on = 1, + }, +}; + +/* OTGi/1190-EV1 HPVDD & AVDD */ +static struct regulator_init_data wm8350_ldo4_data = { + .constraints = { + .name = "PVDD_OTGI/HPVDD/AVDD", + .min_uV = 1200000, + .max_uV = 1200000, + .apply_uV = 1, + .always_on = 1, + }, +}; + +static struct { + int regulator; + struct regulator_init_data *initdata; +} wm1190_regulators[] = { + { WM8350_DCDC_1, &wm8350_dcdc1_data }, + { WM8350_DCDC_3, &wm8350_dcdc3_data }, + { WM8350_DCDC_4, &wm8350_dcdc4_data }, + { WM8350_DCDC_6, &wm8350_dcdc6_data }, + { WM8350_LDO_1, &wm8350_ldo1_data }, + { WM8350_LDO_2, &wm8350_ldo2_data }, + { WM8350_LDO_3, &wm8350_ldo3_data }, + { WM8350_LDO_4, &wm8350_ldo4_data }, +}; + +static int __init smdk6410_wm8350_init(struct wm8350 *wm8350) +{ + int i; + + /* Instantiate the regulators */ + for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++) + wm8350_register_regulator(wm8350, + wm1190_regulators[i].regulator, + wm1190_regulators[i].initdata); + + return 0; +} + +static struct wm8350_platform_data __initdata smdk6410_wm8350_pdata = { + .init = smdk6410_wm8350_init, + .irq_high = 1, +}; +#endif + static struct i2c_board_info i2c_devs0[] __initdata = { { I2C_BOARD_INFO("24c08", 0x50), }, { I2C_BOARD_INFO("wm8580", 0x1b), }, + +#ifdef CONFIG_SMDK6410_WM1190_EV1 + { I2C_BOARD_INFO("wm8350", 0x1a), + .platform_data = &smdk6410_wm8350_pdata, + .irq = S3C_EINT(12), + }, +#endif }; static struct i2c_board_info i2c_devs1[] __initdata = { @@ -155,9 +339,23 @@ static struct i2c_board_info i2c_devs1[] __initdata = { static void __init smdk6410_map_io(void) { + u32 tmp; + s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc)); s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs)); + + /* set the LCD type */ + + tmp = __raw_readl(S3C64XX_SPCON); + tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK; + tmp |= S3C64XX_SPCON_LCD_SEL_RGB; + __raw_writel(tmp, S3C64XX_SPCON); + + /* remove the lcd bypass */ + tmp = __raw_readl(S3C64XX_MODEM_MIFPCON); + tmp &= ~MIFPCON_LCD_BYPASS; + __raw_writel(tmp, S3C64XX_MODEM_MIFPCON); } static void __init smdk6410_machine_init(void) diff --git a/arch/arm/mach-s3c6410/setup-sdhci.c b/arch/arm/mach-s3c6410/setup-sdhci.c index 0b5788bd5985..20666f3bd478 100644 --- a/arch/arm/mach-s3c6410/setup-sdhci.c +++ b/arch/arm/mach-s3c6410/setup-sdhci.c @@ -21,8 +21,6 @@ #include <linux/mmc/card.h> #include <linux/mmc/host.h> -#include <mach/gpio.h> -#include <plat/gpio-cfg.h> #include <plat/regs-sdhci.h> #include <plat/sdhci.h> @@ -35,22 +33,6 @@ char *s3c6410_hsmmc_clksrcs[4] = { /* [3] = "48m", - note not succesfully used yet */ }; -void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width) -{ - unsigned int gpio; - unsigned int end; - - end = S3C64XX_GPG(2 + width); - - /* Set all the necessary GPG pins to special-function 0 */ - for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) { - s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); - s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); - } - - s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP); - s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2)); -} void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev, void __iomem *r, @@ -84,19 +66,3 @@ void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev, writel(ctrl3, r + S3C_SDHCI_CONTROL3); } -void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width) -{ - unsigned int gpio; - unsigned int end; - - end = S3C64XX_GPH(2 + width); - - /* Set all the necessary GPG pins to special-function 0 */ - for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) { - s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); - s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); - } - - s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP); - s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3)); -} diff --git a/arch/arm/mach-versatile/core.c b/arch/arm/mach-versatile/core.c index b3bebcc5623b..69214fc8bd19 100644 --- a/arch/arm/mach-versatile/core.c +++ b/arch/arm/mach-versatile/core.c @@ -116,7 +116,7 @@ void __init versatile_init_irq(void) { unsigned int i; - vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0); + vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0, 0); set_irq_chained_handler(IRQ_VICSOURCE31, sic_handle_irq); diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig index de9383814e5e..935c7558469b 100644 --- a/arch/arm/plat-s3c/Kconfig +++ b/arch/arm/plat-s3c/Kconfig @@ -71,6 +71,15 @@ config S3C2410_PM_DEBUG Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> for more information. +config S3C_PM_DEBUG_LED_SMDK + bool "SMDK LED suspend/resume debugging" + depends on PM && (MACH_SMDK6410) + help + Say Y here to enable the use of the SMDK LEDs on the baseboard + for debugging of the state of the suspend and resume process. + + Note, this currently only works for S3C64XX based SMDK boards. + config S3C2410_PM_CHECK bool "S3C2410 PM Suspend Memory CRC" depends on PM && CRC32 @@ -150,6 +159,13 @@ config S3C_GPIO_CFG_S3C64XX Internal configuration to enable S3C64XX style GPIO configuration functions. +# DMA + +config S3C_DMA + bool + help + Internal configuration for S3C DMA core + # device definitions to compile in config S3C_DEV_HSMMC @@ -172,4 +188,14 @@ config S3C_DEV_FB help Compile in platform device definition for framebuffer +config S3C_DEV_USB_HOST + bool + help + Compile in platform device definition for USB host. + +config S3C_DEV_USB_HSOTG + bool + help + Compile in platform device definition for USB high-speed OtG + endif diff --git a/arch/arm/plat-s3c/Makefile b/arch/arm/plat-s3c/Makefile index 8d7815d25a51..610651455a78 100644 --- a/arch/arm/plat-s3c/Makefile +++ b/arch/arm/plat-s3c/Makefile @@ -18,9 +18,14 @@ obj-y += pwm-clock.o obj-y += gpio.o obj-y += gpio-config.o +# DMA support + +obj-$(CONFIG_S3C_DMA) += dma.o + # PM support obj-$(CONFIG_PM) += pm.o +obj-$(CONFIG_PM) += pm-gpio.o obj-$(CONFIG_S3C2410_PM_CHECK) += pm-check.o # devices @@ -30,3 +35,5 @@ obj-$(CONFIG_S3C_DEV_HSMMC1) += dev-hsmmc1.o obj-y += dev-i2c0.o obj-$(CONFIG_S3C_DEV_I2C1) += dev-i2c1.o obj-$(CONFIG_S3C_DEV_FB) += dev-fb.o +obj-$(CONFIG_S3C_DEV_USB_HOST) += dev-usb.o +obj-$(CONFIG_S3C_DEV_USB_HSOTG) += dev-usb-hsotg.o diff --git a/arch/arm/plat-s3c/dev-usb-hsotg.c b/arch/arm/plat-s3c/dev-usb-hsotg.c new file mode 100644 index 000000000000..e2f604b51c86 --- /dev/null +++ b/arch/arm/plat-s3c/dev-usb-hsotg.c @@ -0,0 +1,41 @@ +/* linux/arch/arm/plat-s3c/dev-usb-hsotg.c + * + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C series device definition for USB high-speed UDC/OtG block + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/platform_device.h> + +#include <mach/irqs.h> +#include <mach/map.h> + +#include <plat/devs.h> + +static struct resource s3c_usb_hsotg_resources[] = { + [0] = { + .start = S3C_PA_USB_HSOTG, + .end = S3C_PA_USB_HSOTG + 0x10000 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_OTG, + .end = IRQ_OTG, + .flags = IORESOURCE_IRQ, + }, +}; + +struct platform_device s3c_device_usb_hsotg = { + .name = "s3c-hsotg", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_usb_hsotg_resources), + .resource = s3c_usb_hsotg_resources, +}; diff --git a/arch/arm/plat-s3c/dev-usb.c b/arch/arm/plat-s3c/dev-usb.c new file mode 100644 index 000000000000..2ee85abed6d9 --- /dev/null +++ b/arch/arm/plat-s3c/dev-usb.c @@ -0,0 +1,50 @@ +/* linux/arch/arm/plat-s3c/dev-usb.c + * + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C series device definition for USB host + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/platform_device.h> + +#include <mach/irqs.h> +#include <mach/map.h> + +#include <plat/devs.h> + + +static struct resource s3c_usb_resource[] = { + [0] = { + .start = S3C_PA_USBHOST, + .end = S3C_PA_USBHOST + 0x100 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_USBH, + .end = IRQ_USBH, + .flags = IORESOURCE_IRQ, + } +}; + +static u64 s3c_device_usb_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_usb = { + .name = "s3c2410-ohci", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_usb_resource), + .resource = s3c_usb_resource, + .dev = { + .dma_mask = &s3c_device_usb_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_usb); diff --git a/arch/arm/plat-s3c/dma.c b/arch/arm/plat-s3c/dma.c new file mode 100644 index 000000000000..c9db75c06af5 --- /dev/null +++ b/arch/arm/plat-s3c/dma.c @@ -0,0 +1,86 @@ +/* linux/arch/arm/plat-s3c/dma.c + * + * Copyright (c) 2003-2005,2006,2009 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C DMA core + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +struct s3c2410_dma_buf; + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/errno.h> + +#include <mach/dma.h> +#include <mach/irqs.h> + +#include <plat/dma-plat.h> + +/* dma channel state information */ +struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS]; +struct s3c2410_dma_chan *s3c_dma_chan_map[DMACH_MAX]; + +/* s3c_dma_lookup_channel + * + * change the dma channel number given into a real dma channel id +*/ + +struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel) +{ + if (channel & DMACH_LOW_LEVEL) + return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL]; + else + return s3c_dma_chan_map[channel]; +} + +/* do we need to protect the settings of the fields from + * irq? +*/ + +int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn); + + chan->op_fn = rtn; + + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_set_opfn); + +int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn); + + chan->callback_fn = rtn; + + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn); + +int s3c2410_dma_setflags(unsigned int channel, unsigned int flags) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + if (chan == NULL) + return -EINVAL; + + chan->flags = flags; + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_setflags); diff --git a/arch/arm/plat-s3c/gpio.c b/arch/arm/plat-s3c/gpio.c index d71dd6d9ce5c..260fdc6ad685 100644 --- a/arch/arm/plat-s3c/gpio.c +++ b/arch/arm/plat-s3c/gpio.c @@ -16,7 +16,7 @@ #include <linux/io.h> #include <linux/gpio.h> -#include <plat/gpio-core.h> +#include <mach/gpio-core.h> #ifdef CONFIG_S3C_GPIO_TRACK struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END]; @@ -140,6 +140,15 @@ __init void s3c_gpiolib_add(struct s3c_gpio_chip *chip) if (!gc->get) gc->get = s3c_gpiolib_get; +#ifdef CONFIG_PM + if (chip->pm != NULL) { + if (!chip->pm->save || !chip->pm->resume) + printk(KERN_ERR "gpio: %s has missing PM functions\n", + gc->label); + } else + printk(KERN_ERR "gpio: %s has no PM function\n", gc->label); +#endif + /* gpiochip_add() prints own failure message on error. */ ret = gpiochip_add(gc); if (ret >= 0) diff --git a/arch/arm/plat-s3c/include/plat/adc.h b/arch/arm/plat-s3c/include/plat/adc.h index 43df2a404b0b..d847bd476b6c 100644 --- a/arch/arm/plat-s3c/include/plat/adc.h +++ b/arch/arm/plat-s3c/include/plat/adc.h @@ -19,10 +19,12 @@ struct s3c_adc_client; extern int s3c_adc_start(struct s3c_adc_client *client, unsigned int channel, unsigned int nr_samples); -extern struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev, - void (*select)(unsigned selected), - void (*conv)(unsigned d0, unsigned d1), - unsigned int is_ts); +extern struct s3c_adc_client * + s3c_adc_register(struct platform_device *pdev, + void (*select)(unsigned selected), + void (*conv)(unsigned d0, unsigned d1, + unsigned *samples_left), + unsigned int is_ts); extern void s3c_adc_release(struct s3c_adc_client *client); diff --git a/arch/arm/plat-s3c/include/plat/clock.h b/arch/arm/plat-s3c/include/plat/clock.h index a10622eed43a..d86af84b5b8c 100644 --- a/arch/arm/plat-s3c/include/plat/clock.h +++ b/arch/arm/plat-s3c/include/plat/clock.h @@ -50,6 +50,7 @@ extern struct clk clk_xtal; extern struct clk clk_ext; /* S3C64XX specific clocks */ +extern struct clk clk_h2; extern struct clk clk_27m; extern struct clk clk_48m; diff --git a/arch/arm/plat-s3c/include/plat/cpu.h b/arch/arm/plat-s3c/include/plat/cpu.h index e62ae0fcfe56..be541cbba070 100644 --- a/arch/arm/plat-s3c/include/plat/cpu.h +++ b/arch/arm/plat-s3c/include/plat/cpu.h @@ -69,3 +69,6 @@ extern struct sysdev_class s3c2412_sysclass; extern struct sysdev_class s3c2440_sysclass; extern struct sysdev_class s3c2442_sysclass; extern struct sysdev_class s3c2443_sysclass; +extern struct sysdev_class s3c6410_sysclass; +extern struct sysdev_class s3c64xx_sysclass; + diff --git a/arch/arm/plat-s3c/include/plat/devs.h b/arch/arm/plat-s3c/include/plat/devs.h index 26f0cec3ac04..a0b6768fddcf 100644 --- a/arch/arm/plat-s3c/include/plat/devs.h +++ b/arch/arm/plat-s3c/include/plat/devs.h @@ -45,6 +45,7 @@ extern struct platform_device s3c_device_spi1; extern struct platform_device s3c_device_nand; extern struct platform_device s3c_device_usbgadget; +extern struct platform_device s3c_device_usb_hsotg; /* s3c2440 specific devices */ diff --git a/arch/arm/plat-s3c/include/plat/dma-core.h b/arch/arm/plat-s3c/include/plat/dma-core.h new file mode 100644 index 000000000000..32ff2a92cb3c --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/dma-core.h @@ -0,0 +1,22 @@ +/* arch/arm/plat-s3c/include/plat/dma.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * Samsung S3C DMA core support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +extern struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel); + +extern struct s3c2410_dma_chan *s3c_dma_chan_map[]; + +/* the currently allocated channel information */ +extern struct s3c2410_dma_chan s3c2410_chans[]; + + diff --git a/arch/arm/plat-s3c/include/plat/dma.h b/arch/arm/plat-s3c/include/plat/dma.h new file mode 100644 index 000000000000..34dba98f08e1 --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/dma.h @@ -0,0 +1,127 @@ +/* arch/arm/plat-s3c/include/plat/dma.h + * + * Copyright (C) 2003,2004,2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Samsung S3C DMA support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +enum s3c2410_dma_buffresult { + S3C2410_RES_OK, + S3C2410_RES_ERR, + S3C2410_RES_ABORT +}; + +enum s3c2410_dmasrc { + S3C2410_DMASRC_HW, /* source is memory */ + S3C2410_DMASRC_MEM /* source is hardware */ +}; + +/* enum s3c2410_chan_op + * + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state +*/ + +enum s3c2410_chan_op { + S3C2410_DMAOP_START, + S3C2410_DMAOP_STOP, + S3C2410_DMAOP_PAUSE, + S3C2410_DMAOP_RESUME, + S3C2410_DMAOP_FLUSH, + S3C2410_DMAOP_TIMEOUT, /* internal signal to handler */ + S3C2410_DMAOP_STARTED, /* indicate channel started */ +}; + +struct s3c2410_dma_client { + char *name; +}; + +struct s3c2410_dma_chan; + +/* s3c2410_dma_cbfn_t + * + * buffer callback routine type +*/ + +typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *, + void *buf, int size, + enum s3c2410_dma_buffresult result); + +typedef int (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *, + enum s3c2410_chan_op ); + + + +/* s3c2410_dma_request + * + * request a dma channel exclusivley +*/ + +extern int s3c2410_dma_request(unsigned int channel, + struct s3c2410_dma_client *, void *dev); + + +/* s3c2410_dma_ctrl + * + * change the state of the dma channel +*/ + +extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op); + +/* s3c2410_dma_setflags + * + * set the channel's flags to a given state +*/ + +extern int s3c2410_dma_setflags(unsigned int channel, + unsigned int flags); + +/* s3c2410_dma_free + * + * free the dma channel (will also abort any outstanding operations) +*/ + +extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *); + +/* s3c2410_dma_enqueue + * + * place the given buffer onto the queue of operations for the channel. + * The buffer must be allocated from dma coherent memory, or the Dcache/WB + * drained before the buffer is given to the DMA system. +*/ + +extern int s3c2410_dma_enqueue(unsigned int channel, void *id, + dma_addr_t data, int size); + +/* s3c2410_dma_config + * + * configure the dma channel +*/ + +extern int s3c2410_dma_config(unsigned int channel, int xferunit); + +/* s3c2410_dma_devconfig + * + * configure the device we're talking to +*/ + +extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source, + unsigned long devaddr); + +/* s3c2410_dma_getposition + * + * get the position that the dma transfer is currently at +*/ + +extern int s3c2410_dma_getposition(unsigned int channel, + dma_addr_t *src, dma_addr_t *dest); + +extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn); +extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn); + + diff --git a/arch/arm/plat-s3c/include/plat/gpio-core.h b/arch/arm/plat-s3c/include/plat/gpio-core.h index 2fc60a580ac8..32af612767aa 100644 --- a/arch/arm/plat-s3c/include/plat/gpio-core.h +++ b/arch/arm/plat-s3c/include/plat/gpio-core.h @@ -20,6 +20,18 @@ * specific code. */ +struct s3c_gpio_chip; + +/** + * struct s3c_gpio_pm - power management (suspend/resume) information + * @save: Routine to save the state of the GPIO block + * @resume: Routine to resume the GPIO block. + */ +struct s3c_gpio_pm { + void (*save)(struct s3c_gpio_chip *chip); + void (*resume)(struct s3c_gpio_chip *chip); +}; + struct s3c_gpio_cfg; /** @@ -27,6 +39,7 @@ struct s3c_gpio_cfg; * @chip: The chip structure to be exported via gpiolib. * @base: The base pointer to the gpio configuration registers. * @config: special function and pull-resistor control information. + * @pm_save: Save information for suspend/resume support. * * This wrapper provides the necessary information for the Samsung * specific gpios being registered with gpiolib. @@ -34,7 +47,11 @@ struct s3c_gpio_cfg; struct s3c_gpio_chip { struct gpio_chip chip; struct s3c_gpio_cfg *config; + struct s3c_gpio_pm *pm; void __iomem *base; +#ifdef CONFIG_PM + u32 pm_save[4]; +#endif }; static inline struct s3c_gpio_chip *to_s3c_gpio(struct gpio_chip *gpc) @@ -75,3 +92,16 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int chip) static inline void s3c_gpiolib_track(struct s3c_gpio_chip *chip) { } #endif + +#ifdef CONFIG_PM +extern struct s3c_gpio_pm s3c_gpio_pm_1bit; +extern struct s3c_gpio_pm s3c_gpio_pm_2bit; +extern struct s3c_gpio_pm s3c_gpio_pm_4bit; +#define __gpio_pm(x) x +#else +#define s3c_gpio_pm_1bit NULL +#define s3c_gpio_pm_2bit NULL +#define s3c_gpio_pm_4bit NULL +#define __gpio_pm(x) NULL + +#endif /* CONFIG_PM */ diff --git a/arch/arm/plat-s3c/include/plat/pm.h b/arch/arm/plat-s3c/include/plat/pm.h index 3779775133a9..7a797192fcf3 100644 --- a/arch/arm/plat-s3c/include/plat/pm.h +++ b/arch/arm/plat-s3c/include/plat/pm.h @@ -44,6 +44,8 @@ extern void (*pm_cpu_sleep)(void); extern unsigned long s3c_pm_flags; +extern unsigned char pm_uart_udivslot; /* true to save UART UDIVSLOT */ + /* from sleep.S */ extern int s3c_cpu_save(unsigned long *saveblk); @@ -88,6 +90,7 @@ struct pm_uart_save { u32 ufcon; u32 umcon; u32 ubrdiv; + u32 udivslot; }; /* helper functions to save/restore lists of registers. */ @@ -124,6 +127,18 @@ extern void s3c_pm_dbg(const char *msg, ...); #define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt) #endif +#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK +/** + * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs + * @set: set bits for the state of the LEDs + * @clear: clear bits for the state of the LEDs. + */ +extern void s3c_pm_debug_smdkled(u32 set, u32 clear); + +#else +static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { } +#endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */ + /* suspend memory checking */ #ifdef CONFIG_S3C2410_PM_CHECK diff --git a/arch/arm/plat-s3c/include/plat/regs-serial.h b/arch/arm/plat-s3c/include/plat/regs-serial.h index 487d7d2a7e1d..66af75a5cdd1 100644 --- a/arch/arm/plat-s3c/include/plat/regs-serial.h +++ b/arch/arm/plat-s3c/include/plat/regs-serial.h @@ -189,6 +189,11 @@ #define S3C2443_DIVSLOT (0x2C) +/* S3C64XX interrupt registers. */ +#define S3C64XX_UINTP 0x30 +#define S3C64XX_UINTSP 0x34 +#define S3C64XX_UINTM 0x38 + #ifndef __ASSEMBLY__ /* struct s3c24xx_uart_clksrc diff --git a/arch/arm/plat-s3c/include/plat/sdhci.h b/arch/arm/plat-s3c/include/plat/sdhci.h index c4ca3920ca4b..f615308ccdfb 100644 --- a/arch/arm/plat-s3c/include/plat/sdhci.h +++ b/arch/arm/plat-s3c/include/plat/sdhci.h @@ -67,12 +67,52 @@ extern struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata; /* Helper function availablity */ +extern void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *, int w); +extern void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *, int w); + +/* S3C6400 SDHCI setup */ + +#ifdef CONFIG_S3C6400_SETUP_SDHCI +extern char *s3c6400_hsmmc_clksrcs[4]; + +#ifdef CONFIG_S3C_DEV_HSMMC +extern void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev, + void __iomem *r, + struct mmc_ios *ios, + struct mmc_card *card); + +static inline void s3c6400_default_sdhci0(void) +{ + s3c_hsmmc0_def_platdata.clocks = s3c6400_hsmmc_clksrcs; + s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio; + s3c_hsmmc0_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card; +} + +#else +static inline void s3c6400_default_sdhci0(void) { } +#endif /* CONFIG_S3C_DEV_HSMMC */ + +#ifdef CONFIG_S3C_DEV_HSMMC1 +static inline void s3c6400_default_sdhci1(void) +{ + s3c_hsmmc1_def_platdata.clocks = s3c6400_hsmmc_clksrcs; + s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio; + s3c_hsmmc1_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card; +} +#else +static inline void s3c6400_default_sdhci1(void) { } +#endif /* CONFIG_S3C_DEV_HSMMC1 */ + +#else +static inline void s3c6400_default_sdhci0(void) { } +static inline void s3c6400_default_sdhci1(void) { } +#endif /* CONFIG_S3C6400_SETUP_SDHCI */ + +/* S3C6410 SDHCI setup */ + #ifdef CONFIG_S3C6410_SETUP_SDHCI extern char *s3c6410_hsmmc_clksrcs[4]; -extern void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *, int w); -extern void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *, int w); - extern void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev, void __iomem *r, struct mmc_ios *ios, @@ -82,7 +122,7 @@ extern void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev, static inline void s3c6410_default_sdhci0(void) { s3c_hsmmc0_def_platdata.clocks = s3c6410_hsmmc_clksrcs; - s3c_hsmmc0_def_platdata.cfg_gpio = s3c6410_setup_sdhci0_cfg_gpio; + s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio; s3c_hsmmc0_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card; } #else @@ -93,7 +133,7 @@ static inline void s3c6410_default_sdhci0(void) { } static inline void s3c6410_default_sdhci1(void) { s3c_hsmmc1_def_platdata.clocks = s3c6410_hsmmc_clksrcs; - s3c_hsmmc1_def_platdata.cfg_gpio = s3c6410_setup_sdhci1_cfg_gpio; + s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio; s3c_hsmmc1_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card; } #else diff --git a/arch/arm/plat-s3c/include/plat/udc-hs.h b/arch/arm/plat-s3c/include/plat/udc-hs.h new file mode 100644 index 000000000000..dd04db043109 --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/udc-hs.h @@ -0,0 +1,29 @@ +/* arch/arm/plat-s3c/include/plat/udc-hs.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C USB2.0 High-speed / OtG platform information + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +enum s3c_hostg_dmamode { + S3C_HSOTG_DMA_NONE, /* do not use DMA at-all */ + S3C_HSOTG_DMA_ONLY, /* always use DMA */ + S3C_HSOTG_DMA_DRV, /* DMA is chosen by driver */ +}; + +/** + * struct s3c_hsotg_plat - platform data for high-speed otg/udc + * @dma: Whether to use DMA or not. + * @is_osc: The clock source is an oscillator, not a crystal + */ +struct s3c_hsotg_plat { + enum s3c_hostg_dmamode dma; + unsigned int is_osc : 1; +}; diff --git a/arch/arm/plat-s3c/include/plat/watchdog-reset.h b/arch/arm/plat-s3c/include/plat/watchdog-reset.h new file mode 100644 index 000000000000..54b762acb5a0 --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/watchdog-reset.h @@ -0,0 +1,49 @@ +/* arch/arm/plat-s3c/include/plat/watchdog-reset.h + * + * Copyright (c) 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2410 - System define for arch_reset() function + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <plat/regs-watchdog.h> +#include <mach/map.h> + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +static inline void arch_wdt_reset(void) +{ + struct clk *wdtclk; + + printk("arch_reset: attempting watchdog reset\n"); + + __raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */ + + wdtclk = clk_get(NULL, "watchdog"); + if (!IS_ERR(wdtclk)) { + clk_enable(wdtclk); + } else + printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__); + + /* put initial values into count and data */ + __raw_writel(0x80, S3C2410_WTCNT); + __raw_writel(0x80, S3C2410_WTDAT); + + /* set the watchdog to go and reset... */ + __raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN | + S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON); + + /* wait for reset to assert... */ + mdelay(500); + + printk(KERN_ERR "Watchdog reset failed to assert reset\n"); + + /* delay to allow the serial port to show the message */ + mdelay(50); +} diff --git a/arch/arm/plat-s3c/pm-gpio.c b/arch/arm/plat-s3c/pm-gpio.c new file mode 100644 index 000000000000..cfd326a8b693 --- /dev/null +++ b/arch/arm/plat-s3c/pm-gpio.c @@ -0,0 +1,380 @@ + +/* linux/arch/arm/plat-s3c/pm-gpio.c + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C series GPIO PM code + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/sysdev.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/gpio.h> + +#include <mach/gpio-core.h> +#include <plat/pm.h> + +/* PM GPIO helpers */ + +#define OFFS_CON (0x00) +#define OFFS_DAT (0x04) +#define OFFS_UP (0x08) + +static void s3c_gpio_pm_1bit_save(struct s3c_gpio_chip *chip) +{ + chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON); + chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT); +} + +static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip) +{ + void __iomem *base = chip->base; + u32 old_gpcon = __raw_readl(base + OFFS_CON); + u32 old_gpdat = __raw_readl(base + OFFS_DAT); + u32 gps_gpcon = chip->pm_save[0]; + u32 gps_gpdat = chip->pm_save[1]; + u32 gpcon; + + /* GPACON only has one bit per control / data and no PULLUPs. + * GPACON[x] = 0 => Output, 1 => SFN */ + + /* first set all SFN bits to SFN */ + + gpcon = old_gpcon | gps_gpcon; + __raw_writel(gpcon, base + OFFS_CON); + + /* now set all the other bits */ + + __raw_writel(gps_gpdat, base + OFFS_DAT); + __raw_writel(gps_gpcon, base + OFFS_CON); + + S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n", + chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat); +} + +struct s3c_gpio_pm s3c_gpio_pm_1bit = { + .save = s3c_gpio_pm_1bit_save, + .resume = s3c_gpio_pm_1bit_resume, +}; + +static void s3c_gpio_pm_2bit_save(struct s3c_gpio_chip *chip) +{ + chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON); + chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT); + chip->pm_save[2] = __raw_readl(chip->base + OFFS_UP); +} + +/* Test whether the given masked+shifted bits of an GPIO configuration + * are one of the SFN (special function) modes. */ + +static inline int is_sfn(unsigned long con) +{ + return con >= 2; +} + +/* Test if the given masked+shifted GPIO configuration is an input */ + +static inline int is_in(unsigned long con) +{ + return con == 0; +} + +/* Test if the given masked+shifted GPIO configuration is an output */ + +static inline int is_out(unsigned long con) +{ + return con == 1; +} + +/** + * s3c_gpio_pm_2bit_resume() - restore the given GPIO bank + * @chip: The chip information to resume. + * + * Restore one of the GPIO banks that was saved during suspend. This is + * not as simple as once thought, due to the possibility of glitches + * from the order that the CON and DAT registers are set in. + * + * The three states the pin can be are {IN,OUT,SFN} which gives us 9 + * combinations of changes to check. Three of these, if the pin stays + * in the same configuration can be discounted. This leaves us with + * the following: + * + * { IN => OUT } Change DAT first + * { IN => SFN } Change CON first + * { OUT => SFN } Change CON first, so new data will not glitch + * { OUT => IN } Change CON first, so new data will not glitch + * { SFN => IN } Change CON first + * { SFN => OUT } Change DAT first, so new data will not glitch [1] + * + * We do not currently deal with the UP registers as these control + * weak resistors, so a small delay in change should not need to bring + * these into the calculations. + * + * [1] this assumes that writing to a pin DAT whilst in SFN will set the + * state for when it is next output. + */ +static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip) +{ + void __iomem *base = chip->base; + u32 old_gpcon = __raw_readl(base + OFFS_CON); + u32 old_gpdat = __raw_readl(base + OFFS_DAT); + u32 gps_gpcon = chip->pm_save[0]; + u32 gps_gpdat = chip->pm_save[1]; + u32 gpcon, old, new, mask; + u32 change_mask = 0x0; + int nr; + + /* restore GPIO pull-up settings */ + __raw_writel(chip->pm_save[2], base + OFFS_UP); + + /* Create a change_mask of all the items that need to have + * their CON value changed before their DAT value, so that + * we minimise the work between the two settings. + */ + + for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) { + old = (old_gpcon & mask) >> nr; + new = (gps_gpcon & mask) >> nr; + + /* If there is no change, then skip */ + + if (old == new) + continue; + + /* If both are special function, then skip */ + + if (is_sfn(old) && is_sfn(new)) + continue; + + /* Change is IN => OUT, do not change now */ + + if (is_in(old) && is_out(new)) + continue; + + /* Change is SFN => OUT, do not change now */ + + if (is_sfn(old) && is_out(new)) + continue; + + /* We should now be at the case of IN=>SFN, + * OUT=>SFN, OUT=>IN, SFN=>IN. */ + + change_mask |= mask; + } + + + /* Write the new CON settings */ + + gpcon = old_gpcon & ~change_mask; + gpcon |= gps_gpcon & change_mask; + + __raw_writel(gpcon, base + OFFS_CON); + + /* Now change any items that require DAT,CON */ + + __raw_writel(gps_gpdat, base + OFFS_DAT); + __raw_writel(gps_gpcon, base + OFFS_CON); + + S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n", + chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat); +} + +struct s3c_gpio_pm s3c_gpio_pm_2bit = { + .save = s3c_gpio_pm_2bit_save, + .resume = s3c_gpio_pm_2bit_resume, +}; + +#ifdef CONFIG_ARCH_S3C64XX +static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip) +{ + chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON); + chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT); + chip->pm_save[3] = __raw_readl(chip->base + OFFS_UP); + + if (chip->chip.ngpio > 8) + chip->pm_save[0] = __raw_readl(chip->base - 4); +} + +static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon) +{ + u32 old, new, mask; + u32 change_mask = 0x0; + int nr; + + for (nr = 0, mask = 0x0f; nr < 16; nr += 4, mask <<= 4) { + old = (old_gpcon & mask) >> nr; + new = (gps_gpcon & mask) >> nr; + + /* If there is no change, then skip */ + + if (old == new) + continue; + + /* If both are special function, then skip */ + + if (is_sfn(old) && is_sfn(new)) + continue; + + /* Change is IN => OUT, do not change now */ + + if (is_in(old) && is_out(new)) + continue; + + /* Change is SFN => OUT, do not change now */ + + if (is_sfn(old) && is_out(new)) + continue; + + /* We should now be at the case of IN=>SFN, + * OUT=>SFN, OUT=>IN, SFN=>IN. */ + + change_mask |= mask; + } + + return change_mask; +} + +static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index) +{ + void __iomem *con = chip->base + (index * 4); + u32 old_gpcon = __raw_readl(con); + u32 gps_gpcon = chip->pm_save[index + 1]; + u32 gpcon, mask; + + mask = s3c_gpio_pm_4bit_mask(old_gpcon, gps_gpcon); + + gpcon = old_gpcon & ~mask; + gpcon |= gps_gpcon & mask; + + __raw_writel(gpcon, con); +} + +static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip) +{ + void __iomem *base = chip->base; + u32 old_gpcon[2]; + u32 old_gpdat = __raw_readl(base + OFFS_DAT); + u32 gps_gpdat = chip->pm_save[2]; + + /* First, modify the CON settings */ + + old_gpcon[0] = 0; + old_gpcon[1] = __raw_readl(base + OFFS_CON); + + s3c_gpio_pm_4bit_con(chip, 0); + if (chip->chip.ngpio > 8) { + old_gpcon[0] = __raw_readl(base - 4); + s3c_gpio_pm_4bit_con(chip, -1); + } + + /* Now change the configurations that require DAT,CON */ + + __raw_writel(chip->pm_save[2], base + OFFS_DAT); + __raw_writel(chip->pm_save[1], base + OFFS_CON); + if (chip->chip.ngpio > 8) + __raw_writel(chip->pm_save[0], base - 4); + + __raw_writel(chip->pm_save[2], base + OFFS_DAT); + __raw_writel(chip->pm_save[3], base + OFFS_UP); + + if (chip->chip.ngpio > 8) { + S3C_PMDBG("%s: CON4 %08x,%08x => %08x,%08x, DAT %08x => %08x\n", + chip->chip.label, old_gpcon[0], old_gpcon[1], + __raw_readl(base - 4), + __raw_readl(base + OFFS_CON), + old_gpdat, gps_gpdat); + } else + S3C_PMDBG("%s: CON4 %08x => %08x, DAT %08x => %08x\n", + chip->chip.label, old_gpcon[1], + __raw_readl(base + OFFS_CON), + old_gpdat, gps_gpdat); +} + +struct s3c_gpio_pm s3c_gpio_pm_4bit = { + .save = s3c_gpio_pm_4bit_save, + .resume = s3c_gpio_pm_4bit_resume, +}; +#endif /* CONFIG_ARCH_S3C64XX */ + +/** + * s3c_pm_save_gpio() - save gpio chip data for suspend + * @ourchip: The chip for suspend. + */ +static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip) +{ + struct s3c_gpio_pm *pm = ourchip->pm; + + if (pm == NULL || pm->save == NULL) + S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label); + else + pm->save(ourchip); +} + +/** + * s3c_pm_save_gpios() - Save the state of the GPIO banks. + * + * For all the GPIO banks, save the state of each one ready for going + * into a suspend mode. + */ +void s3c_pm_save_gpios(void) +{ + struct s3c_gpio_chip *ourchip; + unsigned int gpio_nr; + + for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) { + ourchip = s3c_gpiolib_getchip(gpio_nr); + if (!ourchip) + continue; + + s3c_pm_save_gpio(ourchip); + + S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n", + ourchip->chip.label, + ourchip->pm_save[0], + ourchip->pm_save[1], + ourchip->pm_save[2], + ourchip->pm_save[3]); + + gpio_nr += ourchip->chip.ngpio; + gpio_nr += CONFIG_S3C_GPIO_SPACE; + } +} + +/** + * s3c_pm_resume_gpio() - restore gpio chip data after suspend + * @ourchip: The suspended chip. + */ +static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip) +{ + struct s3c_gpio_pm *pm = ourchip->pm; + + if (pm == NULL || pm->resume == NULL) + S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label); + else + pm->resume(ourchip); +} + +void s3c_pm_restore_gpios(void) +{ + struct s3c_gpio_chip *ourchip; + unsigned int gpio_nr; + + for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) { + ourchip = s3c_gpiolib_getchip(gpio_nr); + if (!ourchip) + continue; + + s3c_pm_resume_gpio(ourchip); + + gpio_nr += ourchip->chip.ngpio; + gpio_nr += CONFIG_S3C_GPIO_SPACE; + } +} diff --git a/arch/arm/plat-s3c/pm.c b/arch/arm/plat-s3c/pm.c index 061182ca66e3..8d97db2c7a0d 100644 --- a/arch/arm/plat-s3c/pm.c +++ b/arch/arm/plat-s3c/pm.c @@ -21,11 +21,10 @@ #include <asm/cacheflush.h> #include <mach/hardware.h> +#include <mach/map.h> #include <plat/regs-serial.h> #include <mach/regs-clock.h> -#include <mach/regs-gpio.h> -#include <mach/regs-mem.h> #include <mach/regs-irq.h> #include <asm/irq.h> @@ -70,6 +69,8 @@ static inline void s3c_pm_debug_init(void) /* Save the UART configurations if we are configured for debug. */ +unsigned char pm_uart_udivslot; + #ifdef CONFIG_S3C2410_PM_DEBUG struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS]; @@ -83,6 +84,12 @@ static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save) save->ufcon = __raw_readl(regs + S3C2410_UFCON); save->umcon = __raw_readl(regs + S3C2410_UMCON); save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV); + + if (pm_uart_udivslot) + save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT); + + S3C_PMDBG("UART[%d]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n", + uart, save->ulcon, save->ucon, save->ufcon, save->ubrdiv); } static void s3c_pm_save_uarts(void) @@ -98,11 +105,16 @@ static void s3c_pm_restore_uart(unsigned int uart, struct pm_uart_save *save) { void __iomem *regs = S3C_VA_UARTx(uart); + s3c_pm_arch_update_uart(regs, save); + __raw_writel(save->ulcon, regs + S3C2410_ULCON); __raw_writel(save->ucon, regs + S3C2410_UCON); __raw_writel(save->ufcon, regs + S3C2410_UFCON); __raw_writel(save->umcon, regs + S3C2410_UMCON); __raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV); + + if (pm_uart_udivslot) + __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT); } static void s3c_pm_restore_uarts(void) @@ -313,6 +325,9 @@ static int s3c_pm_enter(suspend_state_t state) S3C_PMDBG("%s: post sleep, preparing to return\n", __func__); + /* LEDs should now be 1110 */ + s3c_pm_debug_smdkled(1 << 1, 0); + s3c_pm_check_restore(); /* ok, let's return from sleep */ diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index 2c8a2f5d75ff..5b0bc914f58e 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -71,6 +71,7 @@ config PM_SIMTEC config S3C2410_DMA bool "S3C2410 DMA support" depends on ARCH_S3C2410 + select S3C_DMA help S3C2410 DMA support. This is needed for drivers like sound which use the S3C2410's DMA system to move data to and from the diff --git a/arch/arm/plat-s3c24xx/adc.c b/arch/arm/plat-s3c24xx/adc.c index 91adfa71c172..ee1baf11ad9e 100644 --- a/arch/arm/plat-s3c24xx/adc.c +++ b/arch/arm/plat-s3c24xx/adc.c @@ -45,7 +45,8 @@ struct s3c_adc_client { unsigned char channel; void (*select_cb)(unsigned selected); - void (*convert_cb)(unsigned val1, unsigned val2); + void (*convert_cb)(unsigned val1, unsigned val2, + unsigned *samples_left); }; struct adc_device { @@ -158,7 +159,8 @@ static void s3c_adc_default_select(unsigned select) struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev, void (*select)(unsigned int selected), - void (*conv)(unsigned d0, unsigned d1), + void (*conv)(unsigned d0, unsigned d1, + unsigned *samples_left), unsigned int is_ts) { struct s3c_adc_client *client; @@ -227,9 +229,10 @@ static irqreturn_t s3c_adc_irq(int irq, void *pw) data1 = readl(adc->regs + S3C2410_ADCDAT1); adc_dbg(adc, "read %d: 0x%04x, 0x%04x\n", client->nr_samples, data0, data1); - (client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff); + client->nr_samples--; + (client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff, &client->nr_samples); - if (--client->nr_samples > 0) { + if (client->nr_samples > 0) { /* fire another conversion for this */ client->select_cb(1); diff --git a/arch/arm/plat-s3c24xx/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c index 1a8347cec20a..aa119863c5ce 100644 --- a/arch/arm/plat-s3c24xx/common-smdk.c +++ b/arch/arm/plat-s3c24xx/common-smdk.c @@ -18,6 +18,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/sysdev.h> #include <linux/platform_device.h> @@ -47,27 +48,27 @@ /* LED devices */ static struct s3c24xx_led_platdata smdk_pdata_led4 = { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led4", .def_trigger = "timer", }; static struct s3c24xx_led_platdata smdk_pdata_led5 = { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led5", .def_trigger = "nand-disk", }; static struct s3c24xx_led_platdata smdk_pdata_led6 = { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led6", }; static struct s3c24xx_led_platdata smdk_pdata_led7 = { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led7", }; @@ -184,15 +185,15 @@ void __init smdk_machine_init(void) { /* Configure the LEDs (even if we have no LED support)*/ - s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP); + s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPF4, 1); - s3c2410_gpio_setpin(S3C2410_GPF5, 1); - s3c2410_gpio_setpin(S3C2410_GPF6, 1); - s3c2410_gpio_setpin(S3C2410_GPF7, 1); + s3c2410_gpio_setpin(S3C2410_GPF(4), 1); + s3c2410_gpio_setpin(S3C2410_GPF(5), 1); + s3c2410_gpio_setpin(S3C2410_GPF(6), 1); + s3c2410_gpio_setpin(S3C2410_GPF(7), 1); if (machine_is_smdk2443()) smdk_nand_info.twrph0 = 50; diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c index 16ac01d9b8ab..4eb378c89a39 100644 --- a/arch/arm/plat-s3c24xx/devs.c +++ b/arch/arm/plat-s3c24xx/devs.c @@ -136,36 +136,6 @@ struct platform_device *s3c24xx_uart_src[4] = { struct platform_device *s3c24xx_uart_devs[4] = { }; -/* USB Host Controller */ - -static struct resource s3c_usb_resource[] = { - [0] = { - .start = S3C24XX_PA_USBHOST, - .end = S3C24XX_PA_USBHOST + S3C24XX_SZ_USBHOST - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_USBH, - .end = IRQ_USBH, - .flags = IORESOURCE_IRQ, - } -}; - -static u64 s3c_device_usb_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_usb = { - .name = "s3c2410-ohci", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_usb_resource), - .resource = s3c_usb_resource, - .dev = { - .dma_mask = &s3c_device_usb_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_usb); - /* LCD Controller */ static struct resource s3c_lcd_resource[] = { diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c index 07326f632361..196b19123653 100644 --- a/arch/arm/plat-s3c24xx/dma.c +++ b/arch/arm/plat-s3c24xx/dma.c @@ -31,10 +31,10 @@ #include <asm/irq.h> #include <mach/hardware.h> #include <mach/dma.h> - #include <mach/map.h> -#include <plat/dma.h> +#include <plat/dma-plat.h> +#include <plat/regs-dma.h> /* io map for dma */ static void __iomem *dma_base; @@ -44,8 +44,6 @@ static int dma_channels; static struct s3c24xx_dma_selection dma_sel; -/* dma channel state information */ -struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; /* debugging functions */ @@ -135,21 +133,6 @@ dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan) #define dbg_showchan(chan) do { } while(0) #endif /* CONFIG_S3C2410_DMA_DEBUG */ -static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX]; - -/* lookup_dma_channel - * - * change the dma channel number given into a real dma channel id -*/ - -static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel) -{ - if (channel & DMACH_LOW_LEVEL) - return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL]; - else - return dma_chan_map[channel]; -} - /* s3c2410_dma_stats_timeout * * Update DMA stats from timeout info @@ -214,8 +197,6 @@ s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line) return 0; } - - /* s3c2410_dma_loadbuffer * * load a buffer, and update the channel state @@ -453,7 +434,7 @@ s3c2410_dma_canload(struct s3c2410_dma_chan *chan) int s3c2410_dma_enqueue(unsigned int channel, void *id, dma_addr_t data, int size) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); struct s3c2410_dma_buf *buf; unsigned long flags; @@ -804,7 +785,7 @@ EXPORT_SYMBOL(s3c2410_dma_request); int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); unsigned long flags; if (chan == NULL) @@ -836,7 +817,7 @@ int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client) chan->irq_claimed = 0; if (!(channel & DMACH_LOW_LEVEL)) - dma_chan_map[channel] = NULL; + s3c_dma_chan_map[channel] = NULL; local_irq_restore(flags); @@ -995,7 +976,7 @@ static int s3c2410_dma_started(struct s3c2410_dma_chan *chan) int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); if (chan == NULL) return -EINVAL; @@ -1038,14 +1019,13 @@ EXPORT_SYMBOL(s3c2410_dma_ctrl); /* s3c2410_dma_config * * xfersize: size of unit in bytes (1,2,4) - * dcon: base value of the DCONx register */ int s3c2410_dma_config(unsigned int channel, - int xferunit, - int dcon) + int xferunit) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + unsigned int dcon; pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n", __func__, channel, xferunit, dcon); @@ -1055,10 +1035,33 @@ int s3c2410_dma_config(unsigned int channel, pr_debug("%s: Initial dcon is %08x\n", __func__, dcon); - dcon |= chan->dcon & dma_sel.dcon_mask; + dcon = chan->dcon & dma_sel.dcon_mask; pr_debug("%s: New dcon is %08x\n", __func__, dcon); + switch (chan->req_ch) { + case DMACH_I2S_IN: + case DMACH_I2S_OUT: + case DMACH_PCM_IN: + case DMACH_PCM_OUT: + case DMACH_MIC_IN: + default: + dcon |= S3C2410_DCON_HANDSHAKE; + dcon |= S3C2410_DCON_SYNC_PCLK; + break; + + case DMACH_SDI: + /* note, ensure if need HANDSHAKE or not */ + dcon |= S3C2410_DCON_SYNC_PCLK; + break; + + case DMACH_XD0: + case DMACH_XD1: + dcon |= S3C2410_DCON_HANDSHAKE; + dcon |= S3C2410_DCON_SYNC_HCLK; + break; + } + switch (xferunit) { case 1: dcon |= S3C2410_DCON_BYTE; @@ -1090,58 +1093,6 @@ int s3c2410_dma_config(unsigned int channel, EXPORT_SYMBOL(s3c2410_dma_config); -int s3c2410_dma_setflags(unsigned int channel, unsigned int flags) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, flags=%08x\n", __func__, chan, flags); - - chan->flags = flags; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_setflags); - - -/* do we need to protect the settings of the fields from - * irq? -*/ - -int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn); - - chan->op_fn = rtn; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_set_opfn); - -int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn); - - chan->callback_fn = rtn; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn); /* s3c2410_dma_devconfig * @@ -1150,29 +1101,38 @@ EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn); * source: S3C2410_DMASRC_HW: source is hardware * S3C2410_DMASRC_MEM: source is memory * - * hwcfg: the value for xxxSTCn register, - * bit 0: 0=increment pointer, 1=leave pointer - * bit 1: 0=source is AHB, 1=source is APB - * * devaddr: physical address of the source */ int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source, - int hwcfg, unsigned long devaddr) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + unsigned int hwcfg; if (chan == NULL) return -EINVAL; - pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n", - __func__, (int)source, hwcfg, devaddr); + pr_debug("%s: source=%d, devaddr=%08lx\n", + __func__, (int)source, devaddr); chan->source = source; chan->dev_addr = devaddr; - chan->hw_cfg = hwcfg; + + switch (chan->req_ch) { + case DMACH_XD0: + case DMACH_XD1: + hwcfg = 0; /* AHB */ + break; + + default: + hwcfg = S3C2410_DISRCC_APB; + } + + /* always assume our peripheral desintation is a fixed + * address in memory. */ + hwcfg |= S3C2410_DISRCC_INC; switch (source) { case S3C2410_DMASRC_HW: @@ -1219,7 +1179,7 @@ EXPORT_SYMBOL(s3c2410_dma_devconfig); int s3c2410_dma_getposition(unsigned int channel, dma_addr_t *src, dma_addr_t *dst) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); if (chan == NULL) return -EINVAL; @@ -1278,8 +1238,8 @@ static int s3c2410_dma_resume(struct sys_device *dev) printk(KERN_INFO "dma%d: restoring configuration\n", cp->number); - s3c2410_dma_config(no, cp->xfer_unit, cp->dcon); - s3c2410_dma_devconfig(no, cp->source, cp->hw_cfg, cp->dev_addr); + s3c2410_dma_config(no, cp->xfer_unit); + s3c2410_dma_devconfig(no, cp->source, cp->dev_addr); /* re-select the dma source for this channel */ @@ -1476,7 +1436,8 @@ static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) found: dmach = &s3c2410_chans[ch]; dmach->map = ch_map; - dma_chan_map[channel] = dmach; + dmach->req_ch = channel; + s3c_dma_chan_map[channel] = dmach; /* select the channel */ diff --git a/arch/arm/plat-s3c24xx/gpio.c b/arch/arm/plat-s3c24xx/gpio.c index 4a899c279eb5..95df059b5a1d 100644 --- a/arch/arm/plat-s3c24xx/gpio.c +++ b/arch/arm/plat-s3c24xx/gpio.c @@ -183,35 +183,19 @@ EXPORT_SYMBOL(s3c2410_modify_misccr); int s3c2410_gpio_getirq(unsigned int pin) { - if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15) - return -1; /* not valid interrupts */ + if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15)) + return -EINVAL; /* not valid interrupts */ - if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7) - return -1; /* not valid pin */ + if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7)) + return -EINVAL; /* not valid pin */ - if (pin < S3C2410_GPF4) - return (pin - S3C2410_GPF0) + IRQ_EINT0; + if (pin < S3C2410_GPF(4)) + return (pin - S3C2410_GPF(0)) + IRQ_EINT0; - if (pin < S3C2410_GPG0) - return (pin - S3C2410_GPF4) + IRQ_EINT4; + if (pin < S3C2410_GPG(0)) + return (pin - S3C2410_GPF(4)) + IRQ_EINT4; - return (pin - S3C2410_GPG0) + IRQ_EINT8; + return (pin - S3C2410_GPG(0)) + IRQ_EINT8; } EXPORT_SYMBOL(s3c2410_gpio_getirq); - -int s3c2410_gpio_irq2pin(unsigned int irq) -{ - if (irq >= IRQ_EINT0 && irq <= IRQ_EINT3) - return S3C2410_GPF0 + (irq - IRQ_EINT0); - - if (irq >= IRQ_EINT4 && irq <= IRQ_EINT7) - return S3C2410_GPF4 + (irq - IRQ_EINT4); - - if (irq >= IRQ_EINT8 && irq <= IRQ_EINT23) - return S3C2410_GPG0 + (irq - IRQ_EINT8); - - return -EINVAL; -} - -EXPORT_SYMBOL(s3c2410_gpio_irq2pin); diff --git a/arch/arm/plat-s3c24xx/gpiolib.c b/arch/arm/plat-s3c24xx/gpiolib.c index 5c0491bf738b..6d7a961d3269 100644 --- a/arch/arm/plat-s3c24xx/gpiolib.c +++ b/arch/arm/plat-s3c24xx/gpiolib.c @@ -15,6 +15,7 @@ #include <linux/init.h> #include <linux/module.h> #include <linux/interrupt.h> +#include <linux/sysdev.h> #include <linux/ioport.h> #include <linux/io.h> #include <linux/gpio.h> @@ -22,6 +23,7 @@ #include <mach/gpio-core.h> #include <mach/hardware.h> #include <asm/irq.h> +#include <plat/pm.h> #include <mach/regs-gpio.h> @@ -77,9 +79,10 @@ static int s3c24xx_gpiolib_bankg_toirq(struct gpio_chip *chip, unsigned offset) struct s3c_gpio_chip s3c24xx_gpios[] = { [0] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPA0), + .base = S3C2410_GPACON, + .pm = __gpio_pm(&s3c_gpio_pm_1bit), .chip = { - .base = S3C2410_GPA0, + .base = S3C2410_GPA(0), .owner = THIS_MODULE, .label = "GPIOA", .ngpio = 24, @@ -88,45 +91,50 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { }, }, [1] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPB0), + .base = S3C2410_GPBCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPB0, + .base = S3C2410_GPB(0), .owner = THIS_MODULE, .label = "GPIOB", .ngpio = 16, }, }, [2] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPC0), + .base = S3C2410_GPCCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPC0, + .base = S3C2410_GPC(0), .owner = THIS_MODULE, .label = "GPIOC", .ngpio = 16, }, }, [3] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPD0), + .base = S3C2410_GPDCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPD0, + .base = S3C2410_GPD(0), .owner = THIS_MODULE, .label = "GPIOD", .ngpio = 16, }, }, [4] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPE0), + .base = S3C2410_GPECON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPE0, + .base = S3C2410_GPE(0), .label = "GPIOE", .owner = THIS_MODULE, .ngpio = 16, }, }, [5] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPF0), + .base = S3C2410_GPFCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPF0, + .base = S3C2410_GPF(0), .owner = THIS_MODULE, .label = "GPIOF", .ngpio = 8, @@ -134,14 +142,24 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { }, }, [6] = { - .base = S3C24XX_GPIO_BASE(S3C2410_GPG0), + .base = S3C2410_GPGCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPG0, + .base = S3C2410_GPG(0), .owner = THIS_MODULE, .label = "GPIOG", - .ngpio = 10, + .ngpio = 16, .to_irq = s3c24xx_gpiolib_bankg_toirq, }, + }, { + .base = S3C2410_GPHCON, + .pm = __gpio_pm(&s3c_gpio_pm_2bit), + .chip = { + .base = S3C2410_GPH(0), + .owner = THIS_MODULE, + .label = "GPIOH", + .ngpio = 11, + }, }, }; @@ -156,4 +174,4 @@ static __init int s3c24xx_gpiolib_init(void) return 0; } -arch_initcall(s3c24xx_gpiolib_init); +core_initcall(s3c24xx_gpiolib_init); diff --git a/arch/arm/plat-s3c24xx/include/plat/dma.h b/arch/arm/plat-s3c24xx/include/plat/dma-plat.h index c78efe316fc8..9565ead1bc9b 100644 --- a/arch/arm/plat-s3c24xx/include/plat/dma.h +++ b/arch/arm/plat-s3c24xx/include/plat/dma-plat.h @@ -1,4 +1,4 @@ -/* linux/include/asm-arm/plat-s3c24xx/dma.h +/* linux/arch/arm/plat-s3c24xx/include/plat/dma-plat.h * * Copyright (C) 2006 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> @@ -10,8 +10,10 @@ * published by the Free Software Foundation. */ +#include <plat/dma-core.h> + extern struct sysdev_class dma_sysclass; -extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; +extern struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS]; #define DMA_CH_VALID (1<<31) #define DMA_CH_NEVER (1<<30) @@ -31,8 +33,8 @@ struct s3c24xx_dma_map { const char *name; struct s3c24xx_dma_addr hw_addr; - unsigned long channels[S3C2410_DMA_CHANNELS]; - unsigned long channels_rx[S3C2410_DMA_CHANNELS]; + unsigned long channels[S3C_DMA_CHANNELS]; + unsigned long channels_rx[S3C_DMA_CHANNELS]; }; struct s3c24xx_dma_selection { @@ -58,7 +60,7 @@ extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel); */ struct s3c24xx_dma_order_ch { - unsigned int list[S3C2410_DMA_CHANNELS]; /* list of channels */ + unsigned int list[S3C_DMA_CHANNELS]; /* list of channels */ unsigned int flags; /* flags */ }; diff --git a/arch/arm/plat-s3c24xx/include/plat/map.h b/arch/arm/plat-s3c24xx/include/plat/map.h index eed8f78e7593..c4d133436fc7 100644 --- a/arch/arm/plat-s3c24xx/include/plat/map.h +++ b/arch/arm/plat-s3c24xx/include/plat/map.h @@ -58,7 +58,6 @@ #define S3C24XX_SZ_SPI SZ_1M #define S3C24XX_SZ_SDI SZ_1M #define S3C24XX_SZ_NAND SZ_1M -#define S3C24XX_SZ_USBHOST SZ_1M /* GPIO ports */ diff --git a/arch/arm/plat-s3c24xx/include/plat/pm-core.h b/arch/arm/plat-s3c24xx/include/plat/pm-core.h index c75882113e04..fb45dd9adca5 100644 --- a/arch/arm/plat-s3c24xx/include/plat/pm-core.h +++ b/arch/arm/plat-s3c24xx/include/plat/pm-core.h @@ -57,3 +57,8 @@ static inline void s3c_pm_arch_show_resume_irqs(void) s3c_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND), s3c_irqwake_eintmask); } + +static inline void s3c_pm_arch_update_uart(void __iomem *regs, + struct pm_uart_save *save) +{ +} diff --git a/arch/arm/plat-s3c24xx/include/plat/regs-dma.h b/arch/arm/plat-s3c24xx/include/plat/regs-dma.h new file mode 100644 index 000000000000..3bc0a216df97 --- /dev/null +++ b/arch/arm/plat-s3c24xx/include/plat/regs-dma.h @@ -0,0 +1,145 @@ +/* arch/arm/mach-s3c2410/include/mach/dma.h + * + * Copyright (C) 2003,2004,2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Samsung S3C24XX DMA support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* DMA Register definitions */ + +#define S3C2410_DMA_DISRC (0x00) +#define S3C2410_DMA_DISRCC (0x04) +#define S3C2410_DMA_DIDST (0x08) +#define S3C2410_DMA_DIDSTC (0x0C) +#define S3C2410_DMA_DCON (0x10) +#define S3C2410_DMA_DSTAT (0x14) +#define S3C2410_DMA_DCSRC (0x18) +#define S3C2410_DMA_DCDST (0x1C) +#define S3C2410_DMA_DMASKTRIG (0x20) +#define S3C2412_DMA_DMAREQSEL (0x24) +#define S3C2443_DMA_DMAREQSEL (0x24) + +#define S3C2410_DISRCC_INC (1<<0) +#define S3C2410_DISRCC_APB (1<<1) + +#define S3C2410_DMASKTRIG_STOP (1<<2) +#define S3C2410_DMASKTRIG_ON (1<<1) +#define S3C2410_DMASKTRIG_SWTRIG (1<<0) + +#define S3C2410_DCON_DEMAND (0<<31) +#define S3C2410_DCON_HANDSHAKE (1<<31) +#define S3C2410_DCON_SYNC_PCLK (0<<30) +#define S3C2410_DCON_SYNC_HCLK (1<<30) + +#define S3C2410_DCON_INTREQ (1<<29) + +#define S3C2410_DCON_CH0_XDREQ0 (0<<24) +#define S3C2410_DCON_CH0_UART0 (1<<24) +#define S3C2410_DCON_CH0_SDI (2<<24) +#define S3C2410_DCON_CH0_TIMER (3<<24) +#define S3C2410_DCON_CH0_USBEP1 (4<<24) + +#define S3C2410_DCON_CH1_XDREQ1 (0<<24) +#define S3C2410_DCON_CH1_UART1 (1<<24) +#define S3C2410_DCON_CH1_I2SSDI (2<<24) +#define S3C2410_DCON_CH1_SPI (3<<24) +#define S3C2410_DCON_CH1_USBEP2 (4<<24) + +#define S3C2410_DCON_CH2_I2SSDO (0<<24) +#define S3C2410_DCON_CH2_I2SSDI (1<<24) +#define S3C2410_DCON_CH2_SDI (2<<24) +#define S3C2410_DCON_CH2_TIMER (3<<24) +#define S3C2410_DCON_CH2_USBEP3 (4<<24) + +#define S3C2410_DCON_CH3_UART2 (0<<24) +#define S3C2410_DCON_CH3_SDI (1<<24) +#define S3C2410_DCON_CH3_SPI (2<<24) +#define S3C2410_DCON_CH3_TIMER (3<<24) +#define S3C2410_DCON_CH3_USBEP4 (4<<24) + +#define S3C2410_DCON_SRCSHIFT (24) +#define S3C2410_DCON_SRCMASK (7<<24) + +#define S3C2410_DCON_BYTE (0<<20) +#define S3C2410_DCON_HALFWORD (1<<20) +#define S3C2410_DCON_WORD (2<<20) + +#define S3C2410_DCON_AUTORELOAD (0<<22) +#define S3C2410_DCON_NORELOAD (1<<22) +#define S3C2410_DCON_HWTRIG (1<<23) + +#ifdef CONFIG_CPU_S3C2440 +#define S3C2440_DIDSTC_CHKINT (1<<2) + +#define S3C2440_DCON_CH0_I2SSDO (5<<24) +#define S3C2440_DCON_CH0_PCMIN (6<<24) + +#define S3C2440_DCON_CH1_PCMOUT (5<<24) +#define S3C2440_DCON_CH1_SDI (6<<24) + +#define S3C2440_DCON_CH2_PCMIN (5<<24) +#define S3C2440_DCON_CH2_MICIN (6<<24) + +#define S3C2440_DCON_CH3_MICIN (5<<24) +#define S3C2440_DCON_CH3_PCMOUT (6<<24) +#endif + +#ifdef CONFIG_CPU_S3C2412 + +#define S3C2412_DMAREQSEL_SRC(x) ((x)<<1) + +#define S3C2412_DMAREQSEL_HW (1) + +#define S3C2412_DMAREQSEL_SPI0TX S3C2412_DMAREQSEL_SRC(0) +#define S3C2412_DMAREQSEL_SPI0RX S3C2412_DMAREQSEL_SRC(1) +#define S3C2412_DMAREQSEL_SPI1TX S3C2412_DMAREQSEL_SRC(2) +#define S3C2412_DMAREQSEL_SPI1RX S3C2412_DMAREQSEL_SRC(3) +#define S3C2412_DMAREQSEL_I2STX S3C2412_DMAREQSEL_SRC(4) +#define S3C2412_DMAREQSEL_I2SRX S3C2412_DMAREQSEL_SRC(5) +#define S3C2412_DMAREQSEL_TIMER S3C2412_DMAREQSEL_SRC(9) +#define S3C2412_DMAREQSEL_SDI S3C2412_DMAREQSEL_SRC(10) +#define S3C2412_DMAREQSEL_USBEP1 S3C2412_DMAREQSEL_SRC(13) +#define S3C2412_DMAREQSEL_USBEP2 S3C2412_DMAREQSEL_SRC(14) +#define S3C2412_DMAREQSEL_USBEP3 S3C2412_DMAREQSEL_SRC(15) +#define S3C2412_DMAREQSEL_USBEP4 S3C2412_DMAREQSEL_SRC(16) +#define S3C2412_DMAREQSEL_XDREQ0 S3C2412_DMAREQSEL_SRC(17) +#define S3C2412_DMAREQSEL_XDREQ1 S3C2412_DMAREQSEL_SRC(18) +#define S3C2412_DMAREQSEL_UART0_0 S3C2412_DMAREQSEL_SRC(19) +#define S3C2412_DMAREQSEL_UART0_1 S3C2412_DMAREQSEL_SRC(20) +#define S3C2412_DMAREQSEL_UART1_0 S3C2412_DMAREQSEL_SRC(21) +#define S3C2412_DMAREQSEL_UART1_1 S3C2412_DMAREQSEL_SRC(22) +#define S3C2412_DMAREQSEL_UART2_0 S3C2412_DMAREQSEL_SRC(23) +#define S3C2412_DMAREQSEL_UART2_1 S3C2412_DMAREQSEL_SRC(24) + +#endif + +#define S3C2443_DMAREQSEL_SRC(x) ((x)<<1) + +#define S3C2443_DMAREQSEL_HW (1) + +#define S3C2443_DMAREQSEL_SPI0TX S3C2443_DMAREQSEL_SRC(0) +#define S3C2443_DMAREQSEL_SPI0RX S3C2443_DMAREQSEL_SRC(1) +#define S3C2443_DMAREQSEL_SPI1TX S3C2443_DMAREQSEL_SRC(2) +#define S3C2443_DMAREQSEL_SPI1RX S3C2443_DMAREQSEL_SRC(3) +#define S3C2443_DMAREQSEL_I2STX S3C2443_DMAREQSEL_SRC(4) +#define S3C2443_DMAREQSEL_I2SRX S3C2443_DMAREQSEL_SRC(5) +#define S3C2443_DMAREQSEL_TIMER S3C2443_DMAREQSEL_SRC(9) +#define S3C2443_DMAREQSEL_SDI S3C2443_DMAREQSEL_SRC(10) +#define S3C2443_DMAREQSEL_XDREQ0 S3C2443_DMAREQSEL_SRC(17) +#define S3C2443_DMAREQSEL_XDREQ1 S3C2443_DMAREQSEL_SRC(18) +#define S3C2443_DMAREQSEL_UART0_0 S3C2443_DMAREQSEL_SRC(19) +#define S3C2443_DMAREQSEL_UART0_1 S3C2443_DMAREQSEL_SRC(20) +#define S3C2443_DMAREQSEL_UART1_0 S3C2443_DMAREQSEL_SRC(21) +#define S3C2443_DMAREQSEL_UART1_1 S3C2443_DMAREQSEL_SRC(22) +#define S3C2443_DMAREQSEL_UART2_0 S3C2443_DMAREQSEL_SRC(23) +#define S3C2443_DMAREQSEL_UART2_1 S3C2443_DMAREQSEL_SRC(24) +#define S3C2443_DMAREQSEL_UART3_0 S3C2443_DMAREQSEL_SRC(25) +#define S3C2443_DMAREQSEL_UART3_1 S3C2443_DMAREQSEL_SRC(26) +#define S3C2443_DMAREQSEL_PCMOUT S3C2443_DMAREQSEL_SRC(27) +#define S3C2443_DMAREQSEL_PCMIN S3C2443_DMAREQSEL_SRC(28) +#define S3C2443_DMAREQSEL_MICIN S3C2443_DMAREQSEL_SRC(29) diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c index 062a29339a91..56e5253ca02c 100644 --- a/arch/arm/plat-s3c24xx/pm.c +++ b/arch/arm/plat-s3c24xx/pm.c @@ -30,6 +30,7 @@ #include <linux/suspend.h> #include <linux/errno.h> #include <linux/time.h> +#include <linux/gpio.h> #include <linux/interrupt.h> #include <linux/serial_core.h> #include <linux/io.h> @@ -75,43 +76,10 @@ static struct sleep_save core_save[] = { SAVE_ITEM(S3C2410_CLKSLOW), }; -static struct gpio_sleep { - void __iomem *base; - unsigned int gpcon; - unsigned int gpdat; - unsigned int gpup; -} gpio_save[] = { - [0] = { - .base = S3C2410_GPACON, - }, - [1] = { - .base = S3C2410_GPBCON, - }, - [2] = { - .base = S3C2410_GPCCON, - }, - [3] = { - .base = S3C2410_GPDCON, - }, - [4] = { - .base = S3C2410_GPECON, - }, - [5] = { - .base = S3C2410_GPFCON, - }, - [6] = { - .base = S3C2410_GPGCON, - }, - [7] = { - .base = S3C2410_GPHCON, - }, -}; - static struct sleep_save misc_save[] = { SAVE_ITEM(S3C2410_DCLKCON), }; - /* s3c_pm_check_resume_pin * * check to see if the pin is configured correctly for sleep mode, and @@ -156,195 +124,15 @@ void s3c_pm_configure_extint(void) * and then configure it as an input if it is not */ - for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) { - s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF0); - } - - for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) { - s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8); + for (pin = S3C2410_GPF(0); pin <= S3C2410_GPF(7); pin++) { + s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF(0)); } -} - -/* offsets for CON/DAT/UP registers */ - -#define OFFS_CON (S3C2410_GPACON - S3C2410_GPACON) -#define OFFS_DAT (S3C2410_GPADAT - S3C2410_GPACON) -#define OFFS_UP (S3C2410_GPBUP - S3C2410_GPBCON) - -/* s3c_pm_save_gpios() - * - * Save the state of the GPIOs - */ - -void s3c_pm_save_gpios(void) -{ - struct gpio_sleep *gps = gpio_save; - unsigned int gpio; - - for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) { - void __iomem *base = gps->base; - - gps->gpcon = __raw_readl(base + OFFS_CON); - gps->gpdat = __raw_readl(base + OFFS_DAT); - - if (gpio > 0) - gps->gpup = __raw_readl(base + OFFS_UP); + for (pin = S3C2410_GPG(0); pin <= S3C2410_GPG(7); pin++) { + s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG(0))+8); } } -/* Test whether the given masked+shifted bits of an GPIO configuration - * are one of the SFN (special function) modes. */ - -static inline int is_sfn(unsigned long con) -{ - return (con == 2 || con == 3); -} - -/* Test if the given masked+shifted GPIO configuration is an input */ - -static inline int is_in(unsigned long con) -{ - return con == 0; -} - -/* Test if the given masked+shifted GPIO configuration is an output */ - -static inline int is_out(unsigned long con) -{ - return con == 1; -} - -/** - * s3c2410_pm_restore_gpio() - restore the given GPIO bank - * @index: The number of the GPIO bank being resumed. - * @gps: The sleep confgiuration for the bank. - * - * Restore one of the GPIO banks that was saved during suspend. This is - * not as simple as once thought, due to the possibility of glitches - * from the order that the CON and DAT registers are set in. - * - * The three states the pin can be are {IN,OUT,SFN} which gives us 9 - * combinations of changes to check. Three of these, if the pin stays - * in the same configuration can be discounted. This leaves us with - * the following: - * - * { IN => OUT } Change DAT first - * { IN => SFN } Change CON first - * { OUT => SFN } Change CON first, so new data will not glitch - * { OUT => IN } Change CON first, so new data will not glitch - * { SFN => IN } Change CON first - * { SFN => OUT } Change DAT first, so new data will not glitch [1] - * - * We do not currently deal with the UP registers as these control - * weak resistors, so a small delay in change should not need to bring - * these into the calculations. - * - * [1] this assumes that writing to a pin DAT whilst in SFN will set the - * state for when it is next output. - */ - -static void s3c2410_pm_restore_gpio(int index, struct gpio_sleep *gps) -{ - void __iomem *base = gps->base; - unsigned long gps_gpcon = gps->gpcon; - unsigned long gps_gpdat = gps->gpdat; - unsigned long old_gpcon; - unsigned long old_gpdat; - unsigned long old_gpup = 0x0; - unsigned long gpcon; - int nr; - - old_gpcon = __raw_readl(base + OFFS_CON); - old_gpdat = __raw_readl(base + OFFS_DAT); - - if (base == S3C2410_GPACON) { - /* GPACON only has one bit per control / data and no PULLUPs. - * GPACON[x] = 0 => Output, 1 => SFN */ - - /* first set all SFN bits to SFN */ - - gpcon = old_gpcon | gps->gpcon; - __raw_writel(gpcon, base + OFFS_CON); - - /* now set all the other bits */ - - __raw_writel(gps_gpdat, base + OFFS_DAT); - __raw_writel(gps_gpcon, base + OFFS_CON); - } else { - unsigned long old, new, mask; - unsigned long change_mask = 0x0; - - old_gpup = __raw_readl(base + OFFS_UP); - - /* Create a change_mask of all the items that need to have - * their CON value changed before their DAT value, so that - * we minimise the work between the two settings. - */ - - for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) { - old = (old_gpcon & mask) >> nr; - new = (gps_gpcon & mask) >> nr; - - /* If there is no change, then skip */ - - if (old == new) - continue; - - /* If both are special function, then skip */ - - if (is_sfn(old) && is_sfn(new)) - continue; - - /* Change is IN => OUT, do not change now */ - - if (is_in(old) && is_out(new)) - continue; - - /* Change is SFN => OUT, do not change now */ - - if (is_sfn(old) && is_out(new)) - continue; - - /* We should now be at the case of IN=>SFN, - * OUT=>SFN, OUT=>IN, SFN=>IN. */ - - change_mask |= mask; - } - - /* Write the new CON settings */ - - gpcon = old_gpcon & ~change_mask; - gpcon |= gps_gpcon & change_mask; - - __raw_writel(gpcon, base + OFFS_CON); - - /* Now change any items that require DAT,CON */ - - __raw_writel(gps_gpdat, base + OFFS_DAT); - __raw_writel(gps_gpcon, base + OFFS_CON); - __raw_writel(gps->gpup, base + OFFS_UP); - } - - S3C_PMDBG("GPIO[%d] CON %08lx => %08lx, DAT %08lx => %08lx\n", - index, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat); -} - - -/** s3c2410_pm_restore_gpios() - * - * Restore the state of the GPIOs - */ - -void s3c_pm_restore_gpios(void) -{ - struct gpio_sleep *gps = gpio_save; - int gpio; - - for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) { - s3c2410_pm_restore_gpio(gpio, gps); - } -} void s3c_pm_restore_core(void) { diff --git a/arch/arm/plat-s3c24xx/setup-i2c.c b/arch/arm/plat-s3c24xx/setup-i2c.c index d62b7e7fb355..71a6accf114e 100644 --- a/arch/arm/plat-s3c24xx/setup-i2c.c +++ b/arch/arm/plat-s3c24xx/setup-i2c.c @@ -11,6 +11,7 @@ */ #include <linux/kernel.h> +#include <linux/gpio.h> struct platform_device; @@ -20,6 +21,6 @@ struct platform_device; void s3c_i2c0_cfg_gpio(struct platform_device *dev) { - s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_IICSDA); - s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_IICSCL); + s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA); + s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL); } diff --git a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c index 8b403cbb53d2..9edf7894eedd 100644 --- a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c +++ b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c @@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi, int enable) { if (enable) { - s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPE13_SPICLK0); - s3c2410_gpio_cfgpin(S3C2410_GPE12, S3C2410_GPE12_SPIMOSI0); - s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPE11_SPIMISO0); - s3c2410_gpio_pullup(S3C2410_GPE11, 0); - s3c2410_gpio_pullup(S3C2410_GPE13, 0); + s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0); + s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0); + s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0); + s3c2410_gpio_pullup(S3C2410_GPE(11), 0); + s3c2410_gpio_pullup(S3C2410_GPE(13), 0); } else { - s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPIO_INPUT); - s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPIO_INPUT); - s3c2410_gpio_pullup(S3C2410_GPE11, 1); - s3c2410_gpio_pullup(S3C2410_GPE12, 1); - s3c2410_gpio_pullup(S3C2410_GPE13, 1); + s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT); + s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT); + s3c2410_gpio_pullup(S3C2410_GPE(11), 1); + s3c2410_gpio_pullup(S3C2410_GPE(12), 1); + s3c2410_gpio_pullup(S3C2410_GPE(13), 1); } } diff --git a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c index 8fccd4e549f0..f34d0fc69ad8 100644 --- a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c +++ b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c @@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi, int enable) { if (enable) { - s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPG7_SPICLK1); - s3c2410_gpio_cfgpin(S3C2410_GPG6, S3C2410_GPG6_SPIMOSI1); - s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPG5_SPIMISO1); - s3c2410_gpio_pullup(S3C2410_GPG5, 0); - s3c2410_gpio_pullup(S3C2410_GPG6, 0); + s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1); + s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1); + s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1); + s3c2410_gpio_pullup(S3C2410_GPG(5), 0); + s3c2410_gpio_pullup(S3C2410_GPG(6), 0); } else { - s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPIO_INPUT); - s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPIO_INPUT); - s3c2410_gpio_pullup(S3C2410_GPG5, 1); - s3c2410_gpio_pullup(S3C2410_GPG6, 1); - s3c2410_gpio_pullup(S3C2410_GPG7, 1); + s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT); + s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT); + s3c2410_gpio_pullup(S3C2410_GPG(5), 1); + s3c2410_gpio_pullup(S3C2410_GPG(6), 1); + s3c2410_gpio_pullup(S3C2410_GPG(7), 1); } } diff --git a/arch/arm/plat-s3c64xx/Kconfig b/arch/arm/plat-s3c64xx/Kconfig index 54375a00a7d2..5ebd8b425a54 100644 --- a/arch/arm/plat-s3c64xx/Kconfig +++ b/arch/arm/plat-s3c64xx/Kconfig @@ -19,6 +19,7 @@ config PLAT_S3C64XX select S3C_GPIO_PULL_UPDOWN select S3C_GPIO_CFG_S3C24XX select S3C_GPIO_CFG_S3C64XX + select USB_ARCH_HAS_OHCI help Base platform code for any Samsung S3C64XX device @@ -38,6 +39,10 @@ config CPU_S3C6400_CLOCK Common clock support code for the S3C6400 that is shared by other CPUs in the series, such as the S3C6410. +config S3C64XX_DMA + bool "S3C64XX DMA" + select S3C_DMA + # platform specific device setup config S3C64XX_SETUP_I2C0 @@ -59,4 +64,9 @@ config S3C64XX_SETUP_FB_24BPP help Common setup code for S3C64XX with an 24bpp RGB display helper. +config S3C64XX_SETUP_SDHCI_GPIO + bool + help + Common setup code for S3C64XX SDHCI GPIO configurations + endif diff --git a/arch/arm/plat-s3c64xx/Makefile b/arch/arm/plat-s3c64xx/Makefile index 2e6d79bf8f33..2ed5df34f9ea 100644 --- a/arch/arm/plat-s3c64xx/Makefile +++ b/arch/arm/plat-s3c64xx/Makefile @@ -24,8 +24,19 @@ obj-y += gpiolib.o obj-$(CONFIG_CPU_S3C6400_INIT) += s3c6400-init.o obj-$(CONFIG_CPU_S3C6400_CLOCK) += s3c6400-clock.o +# PM support + +obj-$(CONFIG_PM) += pm.o +obj-$(CONFIG_PM) += sleep.o +obj-$(CONFIG_PM) += irq-pm.o + +# DMA support + +obj-$(CONFIG_S3C64XX_DMA) += dma.o + # Device setup obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o +obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
\ No newline at end of file diff --git a/arch/arm/plat-s3c64xx/clock.c b/arch/arm/plat-s3c64xx/clock.c index ad1b9682c9c3..0bc2fa1dfc40 100644 --- a/arch/arm/plat-s3c64xx/clock.c +++ b/arch/arm/plat-s3c64xx/clock.c @@ -27,6 +27,12 @@ #include <plat/devs.h> #include <plat/clock.h> +struct clk clk_h2 = { + .name = "hclk2", + .id = -1, + .rate = 0, +}; + struct clk clk_27m = { .name = "clk_27m", .id = -1, @@ -152,6 +158,18 @@ static struct clk init_clocks_disable[] = { .parent = &clk_48m, .enable = s3c64xx_sclk_ctrl, .ctrlbit = S3C_CLKCON_SCLK_MMC2_48, + }, { + .name = "dma0", + .id = -1, + .parent = &clk_h, + .enable = s3c64xx_hclk_ctrl, + .ctrlbit = S3C_CLKCON_HCLK_DMA0, + }, { + .name = "dma1", + .id = -1, + .parent = &clk_h, + .enable = s3c64xx_hclk_ctrl, + .ctrlbit = S3C_CLKCON_HCLK_DMA1, }, }; @@ -246,6 +264,7 @@ static struct clk *clks[] __initdata = { &clk_epll, &clk_27m, &clk_48m, + &clk_h2, }; void __init s3c64xx_register_clocks(void) diff --git a/arch/arm/plat-s3c64xx/cpu.c b/arch/arm/plat-s3c64xx/cpu.c index 91f49a3a665d..b1fdd83940a6 100644 --- a/arch/arm/plat-s3c64xx/cpu.c +++ b/arch/arm/plat-s3c64xx/cpu.c @@ -16,6 +16,7 @@ #include <linux/module.h> #include <linux/interrupt.h> #include <linux/ioport.h> +#include <linux/sysdev.h> #include <linux/serial_core.h> #include <linux/platform_device.h> #include <linux/io.h> @@ -101,9 +102,24 @@ static struct map_desc s3c_iodesc[] __initdata = { .pfn = __phys_to_pfn(S3C64XX_PA_MODEM), .length = SZ_4K, .type = MT_DEVICE, + }, { + .virtual = (unsigned long)S3C_VA_WATCHDOG, + .pfn = __phys_to_pfn(S3C64XX_PA_WATCHDOG), + .length = SZ_4K, + .type = MT_DEVICE, }, }; + +struct sysdev_class s3c64xx_sysclass = { + .name = "s3c64xx-core", +}; + +static struct sys_device s3c64xx_sysdev = { + .cls = &s3c64xx_sysclass, +}; + + /* read cpu identification code */ void __init s3c64xx_init_io(struct map_desc *mach_desc, int size) @@ -115,5 +131,21 @@ void __init s3c64xx_init_io(struct map_desc *mach_desc, int size) iotable_init(mach_desc, size); idcode = __raw_readl(S3C_VA_SYS + 0x118); + if (!idcode) { + /* S3C6400 has the ID register in a different place, + * and needs a write before it can be read. */ + + __raw_writel(0x0, S3C_VA_SYS + 0xA1C); + idcode = __raw_readl(S3C_VA_SYS + 0xA1C); + } + s3c_init_cpu(idcode, cpu_ids, ARRAY_SIZE(cpu_ids)); } + +static __init int s3c64xx_sysdev_init(void) +{ + sysdev_class_register(&s3c64xx_sysclass); + return sysdev_register(&s3c64xx_sysdev); +} + +core_initcall(s3c64xx_sysdev_init); diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c new file mode 100644 index 000000000000..67aa93dbb69e --- /dev/null +++ b/arch/arm/plat-s3c64xx/dma.c @@ -0,0 +1,722 @@ +/* linux/arch/arm/plat-s3c64xx/dma.c + * + * Copyright 2009 Openmoko, Inc. + * Copyright 2009 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX DMA core + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/dmapool.h> +#include <linux/sysdev.h> +#include <linux/errno.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +#include <mach/dma.h> +#include <mach/map.h> +#include <mach/irqs.h> + +#include <plat/dma-plat.h> +#include <plat/regs-sys.h> + +#include <asm/hardware/pl080.h> + +/* dma channel state information */ + +struct s3c64xx_dmac { + struct sys_device sysdev; + struct clk *clk; + void __iomem *regs; + struct s3c2410_dma_chan *channels; + enum dma_ch chanbase; +}; + +/* pool to provide LLI buffers */ +static struct dma_pool *dma_pool; + +/* Debug configuration and code */ + +static unsigned char debug_show_buffs = 0; + +static void dbg_showchan(struct s3c2410_dma_chan *chan) +{ + pr_debug("DMA%d: %08x->%08x L %08x C %08x,%08x S %08x\n", + chan->number, + readl(chan->regs + PL080_CH_SRC_ADDR), + readl(chan->regs + PL080_CH_DST_ADDR), + readl(chan->regs + PL080_CH_LLI), + readl(chan->regs + PL080_CH_CONTROL), + readl(chan->regs + PL080S_CH_CONTROL2), + readl(chan->regs + PL080S_CH_CONFIG)); +} + +static void show_lli(struct pl080s_lli *lli) +{ + pr_debug("LLI[%p] %08x->%08x, NL %08x C %08x,%08x\n", + lli, lli->src_addr, lli->dst_addr, lli->next_lli, + lli->control0, lli->control1); +} + +static void dbg_showbuffs(struct s3c2410_dma_chan *chan) +{ + struct s3c64xx_dma_buff *ptr; + struct s3c64xx_dma_buff *end; + + pr_debug("DMA%d: buffs next %p, curr %p, end %p\n", + chan->number, chan->next, chan->curr, chan->end); + + ptr = chan->next; + end = chan->end; + + if (debug_show_buffs) { + for (; ptr != NULL; ptr = ptr->next) { + pr_debug("DMA%d: %08x ", + chan->number, ptr->lli_dma); + show_lli(ptr->lli); + } + } +} + +/* End of Debug */ + +static struct s3c2410_dma_chan *s3c64xx_dma_map_channel(unsigned int channel) +{ + struct s3c2410_dma_chan *chan; + unsigned int start, offs; + + start = 0; + + if (channel >= DMACH_PCM1_TX) + start = 8; + + for (offs = 0; offs < 8; offs++) { + chan = &s3c2410_chans[start + offs]; + if (!chan->in_use) + goto found; + } + + return NULL; + +found: + s3c_dma_chan_map[channel] = chan; + return chan; +} + +int s3c2410_dma_config(unsigned int channel, int xferunit) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + if (chan == NULL) + return -EINVAL; + + switch (xferunit) { + case 1: + chan->hw_width = 0; + break; + case 2: + chan->hw_width = 1; + break; + case 4: + chan->hw_width = 2; + break; + default: + printk(KERN_ERR "%s: illegal width %d\n", __func__, xferunit); + return -EINVAL; + } + + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_config); + +static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan, + struct pl080s_lli *lli, + dma_addr_t data, int size) +{ + dma_addr_t src, dst; + u32 control0, control1; + + switch (chan->source) { + case S3C2410_DMASRC_HW: + src = chan->dev_addr; + dst = data; + control0 = PL080_CONTROL_SRC_AHB2; + control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT; + control0 |= 2 << PL080_CONTROL_DWIDTH_SHIFT; + control0 |= PL080_CONTROL_DST_INCR; + break; + + case S3C2410_DMASRC_MEM: + src = data; + dst = chan->dev_addr; + control0 = PL080_CONTROL_DST_AHB2; + control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT; + control0 |= 2 << PL080_CONTROL_SWIDTH_SHIFT; + control0 |= PL080_CONTROL_SRC_INCR; + break; + default: + BUG(); + } + + /* note, we do not currently setup any of the burst controls */ + + control1 = size >> chan->hw_width; /* size in no of xfers */ + control0 |= PL080_CONTROL_PROT_SYS; /* always in priv. mode */ + control0 |= PL080_CONTROL_TC_IRQ_EN; /* always fire IRQ */ + + lli->src_addr = src; + lli->dst_addr = dst; + lli->next_lli = 0; + lli->control0 = control0; + lli->control1 = control1; +} + +static void s3c64xx_lli_to_regs(struct s3c2410_dma_chan *chan, + struct pl080s_lli *lli) +{ + void __iomem *regs = chan->regs; + + pr_debug("%s: LLI %p => regs\n", __func__, lli); + show_lli(lli); + + writel(lli->src_addr, regs + PL080_CH_SRC_ADDR); + writel(lli->dst_addr, regs + PL080_CH_DST_ADDR); + writel(lli->next_lli, regs + PL080_CH_LLI); + writel(lli->control0, regs + PL080_CH_CONTROL); + writel(lli->control1, regs + PL080S_CH_CONTROL2); +} + +static int s3c64xx_dma_start(struct s3c2410_dma_chan *chan) +{ + struct s3c64xx_dmac *dmac = chan->dmac; + u32 config; + u32 bit = chan->bit; + + dbg_showchan(chan); + + pr_debug("%s: clearing interrupts\n", __func__); + + /* clear interrupts */ + writel(bit, dmac->regs + PL080_TC_CLEAR); + writel(bit, dmac->regs + PL080_ERR_CLEAR); + + pr_debug("%s: starting channel\n", __func__); + + config = readl(chan->regs + PL080S_CH_CONFIG); + config |= PL080_CONFIG_ENABLE; + + pr_debug("%s: writing config %08x\n", __func__, config); + writel(config, chan->regs + PL080S_CH_CONFIG); + + return 0; +} + +static int s3c64xx_dma_stop(struct s3c2410_dma_chan *chan) +{ + u32 config; + int timeout; + + pr_debug("%s: stopping channel\n", __func__); + + dbg_showchan(chan); + + config = readl(chan->regs + PL080S_CH_CONFIG); + config |= PL080_CONFIG_HALT; + writel(config, chan->regs + PL080S_CH_CONFIG); + + timeout = 1000; + do { + config = readl(chan->regs + PL080S_CH_CONFIG); + pr_debug("%s: %d - config %08x\n", __func__, timeout, config); + if (config & PL080_CONFIG_ACTIVE) + udelay(10); + else + break; + } while (--timeout > 0); + + if (config & PL080_CONFIG_ACTIVE) { + printk(KERN_ERR "%s: channel still active\n", __func__); + return -EFAULT; + } + + config = readl(chan->regs + PL080S_CH_CONFIG); + config &= ~PL080_CONFIG_ENABLE; + writel(config, chan->regs + PL080S_CH_CONFIG); + + return 0; +} + +static inline void s3c64xx_dma_bufffdone(struct s3c2410_dma_chan *chan, + struct s3c64xx_dma_buff *buf, + enum s3c2410_dma_buffresult result) +{ + if (chan->callback_fn != NULL) + (chan->callback_fn)(chan, buf->pw, 0, result); +} + +static void s3c64xx_dma_freebuff(struct s3c64xx_dma_buff *buff) +{ + dma_pool_free(dma_pool, buff->lli, buff->lli_dma); + kfree(buff); +} + +static int s3c64xx_dma_flush(struct s3c2410_dma_chan *chan) +{ + struct s3c64xx_dma_buff *buff, *next; + u32 config; + + dbg_showchan(chan); + + pr_debug("%s: flushing channel\n", __func__); + + config = readl(chan->regs + PL080S_CH_CONFIG); + config &= ~PL080_CONFIG_ENABLE; + writel(config, chan->regs + PL080S_CH_CONFIG); + + /* dump all the buffers associated with this channel */ + + for (buff = chan->curr; buff != NULL; buff = next) { + next = buff->next; + pr_debug("%s: buff %p (next %p)\n", __func__, buff, buff->next); + + s3c64xx_dma_bufffdone(chan, buff, S3C2410_RES_ABORT); + s3c64xx_dma_freebuff(buff); + } + + chan->curr = chan->next = chan->end = NULL; + + return 0; +} + +int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + WARN_ON(!chan); + if (!chan) + return -EINVAL; + + switch (op) { + case S3C2410_DMAOP_START: + return s3c64xx_dma_start(chan); + + case S3C2410_DMAOP_STOP: + return s3c64xx_dma_stop(chan); + + case S3C2410_DMAOP_FLUSH: + return s3c64xx_dma_flush(chan); + + /* belive PAUSE/RESUME are no-ops */ + case S3C2410_DMAOP_PAUSE: + case S3C2410_DMAOP_RESUME: + case S3C2410_DMAOP_STARTED: + case S3C2410_DMAOP_TIMEOUT: + return 0; + } + + return -ENOENT; +} +EXPORT_SYMBOL(s3c2410_dma_ctrl); + +/* s3c2410_dma_enque + * + */ + +int s3c2410_dma_enqueue(unsigned int channel, void *id, + dma_addr_t data, int size) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + struct s3c64xx_dma_buff *next; + struct s3c64xx_dma_buff *buff; + struct pl080s_lli *lli; + int ret; + + WARN_ON(!chan); + if (!chan) + return -EINVAL; + + buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_KERNEL); + if (!buff) { + printk(KERN_ERR "%s: no memory for buffer\n", __func__); + return -ENOMEM; + } + + lli = dma_pool_alloc(dma_pool, GFP_KERNEL, &buff->lli_dma); + if (!lli) { + printk(KERN_ERR "%s: no memory for lli\n", __func__); + ret = -ENOMEM; + goto err_buff; + } + + pr_debug("%s: buff %p, dp %08x lli (%p, %08x) %d\n", + __func__, buff, data, lli, (u32)buff->lli_dma, size); + + buff->lli = lli; + buff->pw = id; + + s3c64xx_dma_fill_lli(chan, lli, data, size); + + if ((next = chan->next) != NULL) { + struct s3c64xx_dma_buff *end = chan->end; + struct pl080s_lli *endlli = end->lli; + + pr_debug("enquing onto channel\n"); + + end->next = buff; + endlli->next_lli = buff->lli_dma; + + if (chan->flags & S3C2410_DMAF_CIRCULAR) { + struct s3c64xx_dma_buff *curr = chan->curr; + lli->next_lli = curr->lli_dma; + } + + if (next == chan->curr) { + writel(buff->lli_dma, chan->regs + PL080_CH_LLI); + chan->next = buff; + } + + show_lli(endlli); + chan->end = buff; + } else { + pr_debug("enquing onto empty channel\n"); + + chan->curr = buff; + chan->next = buff; + chan->end = buff; + + s3c64xx_lli_to_regs(chan, lli); + } + + show_lli(lli); + + dbg_showchan(chan); + dbg_showbuffs(chan); + return 0; + +err_buff: + kfree(buff); + return ret; +} + +EXPORT_SYMBOL(s3c2410_dma_enqueue); + + +int s3c2410_dma_devconfig(int channel, + enum s3c2410_dmasrc source, + unsigned long devaddr) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + u32 peripheral; + u32 config = 0; + + pr_debug("%s: channel %d, source %d, dev %08lx, chan %p\n", + __func__, channel, source, devaddr, chan); + + WARN_ON(!chan); + if (!chan) + return -EINVAL; + + peripheral = (chan->peripheral & 0xf); + chan->source = source; + chan->dev_addr = devaddr; + + pr_debug("%s: peripheral %d\n", __func__, peripheral); + + switch (source) { + case S3C2410_DMASRC_HW: + config = 2 << PL080_CONFIG_FLOW_CONTROL_SHIFT; + config |= peripheral << PL080_CONFIG_SRC_SEL_SHIFT; + break; + case S3C2410_DMASRC_MEM: + config = 1 << PL080_CONFIG_FLOW_CONTROL_SHIFT; + config |= peripheral << PL080_CONFIG_DST_SEL_SHIFT; + break; + default: + printk(KERN_ERR "%s: bad source\n", __func__); + return -EINVAL; + } + + /* allow TC and ERR interrupts */ + config |= PL080_CONFIG_TC_IRQ_MASK; + config |= PL080_CONFIG_ERR_IRQ_MASK; + + pr_debug("%s: config %08x\n", __func__, config); + + writel(config, chan->regs + PL080S_CH_CONFIG); + + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_devconfig); + + +int s3c2410_dma_getposition(unsigned int channel, + dma_addr_t *src, dma_addr_t *dst) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + + WARN_ON(!chan); + if (!chan) + return -EINVAL; + + if (src != NULL) + *src = readl(chan->regs + PL080_CH_SRC_ADDR); + + if (dst != NULL) + *dst = readl(chan->regs + PL080_CH_DST_ADDR); + + return 0; +} +EXPORT_SYMBOL(s3c2410_dma_getposition); + +/* s3c2410_request_dma + * + * get control of an dma channel +*/ + +int s3c2410_dma_request(unsigned int channel, + struct s3c2410_dma_client *client, + void *dev) +{ + struct s3c2410_dma_chan *chan; + unsigned long flags; + + pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n", + channel, client->name, dev); + + local_irq_save(flags); + + chan = s3c64xx_dma_map_channel(channel); + if (chan == NULL) { + local_irq_restore(flags); + return -EBUSY; + } + + dbg_showchan(chan); + + chan->client = client; + chan->in_use = 1; + chan->peripheral = channel; + + local_irq_restore(flags); + + /* need to setup */ + + pr_debug("%s: channel initialised, %p\n", __func__, chan); + + return chan->number | DMACH_LOW_LEVEL; +} + +EXPORT_SYMBOL(s3c2410_dma_request); + +/* s3c2410_dma_free + * + * release the given channel back to the system, will stop and flush + * any outstanding transfers, and ensure the channel is ready for the + * next claimant. + * + * Note, although a warning is currently printed if the freeing client + * info is not the same as the registrant's client info, the free is still + * allowed to go through. +*/ + +int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client) +{ + struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel); + unsigned long flags; + + if (chan == NULL) + return -EINVAL; + + local_irq_save(flags); + + if (chan->client != client) { + printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n", + channel, chan->client, client); + } + + /* sort out stopping and freeing the channel */ + + + chan->client = NULL; + chan->in_use = 0; + + if (!(channel & DMACH_LOW_LEVEL)) + s3c_dma_chan_map[channel] = NULL; + + local_irq_restore(flags); + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_free); + + +static void s3c64xx_dma_tcirq(struct s3c64xx_dmac *dmac, int offs) +{ + struct s3c2410_dma_chan *chan = dmac->channels + offs; + + /* note, we currently do not bother to work out which buffer + * or buffers have been completed since the last tc-irq. */ + + if (chan->callback_fn) + (chan->callback_fn)(chan, chan->curr->pw, 0, S3C2410_RES_OK); +} + +static void s3c64xx_dma_errirq(struct s3c64xx_dmac *dmac, int offs) +{ + printk(KERN_DEBUG "%s: offs %d\n", __func__, offs); +} + +static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) +{ + struct s3c64xx_dmac *dmac = pw; + u32 tcstat, errstat; + u32 bit; + int offs; + + tcstat = readl(dmac->regs + PL080_TC_STATUS); + errstat = readl(dmac->regs + PL080_ERR_STATUS); + + for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) { + if (tcstat & bit) { + writel(bit, dmac->regs + PL080_TC_CLEAR); + s3c64xx_dma_tcirq(dmac, offs); + } + + if (errstat & bit) { + s3c64xx_dma_errirq(dmac, offs); + writel(bit, dmac->regs + PL080_ERR_CLEAR); + } + } + + return IRQ_HANDLED; +} + +static struct sysdev_class dma_sysclass = { + .name = "s3c64xx-dma", +}; + +static int s3c64xx_dma_init1(int chno, enum dma_ch chbase, + int irq, unsigned int base) +{ + struct s3c2410_dma_chan *chptr = &s3c2410_chans[chno]; + struct s3c64xx_dmac *dmac; + char clkname[16]; + void __iomem *regs; + void __iomem *regptr; + int err, ch; + + dmac = kzalloc(sizeof(struct s3c64xx_dmac), GFP_KERNEL); + if (!dmac) { + printk(KERN_ERR "%s: failed to alloc mem\n", __func__); + return -ENOMEM; + } + + dmac->sysdev.id = chno / 8; + dmac->sysdev.cls = &dma_sysclass; + + err = sysdev_register(&dmac->sysdev); + if (err) { + printk(KERN_ERR "%s: failed to register sysdevice\n", __func__); + goto err_alloc; + } + + regs = ioremap(base, 0x200); + if (!regs) { + printk(KERN_ERR "%s: failed to ioremap()\n", __func__); + err = -ENXIO; + goto err_dev; + } + + snprintf(clkname, sizeof(clkname), "dma%d", dmac->sysdev.id); + + dmac->clk = clk_get(NULL, clkname); + if (IS_ERR(dmac->clk)) { + printk(KERN_ERR "%s: failed to get clock %s\n", __func__, clkname); + err = PTR_ERR(dmac->clk); + goto err_map; + } + + clk_enable(dmac->clk); + + dmac->regs = regs; + dmac->chanbase = chbase; + dmac->channels = chptr; + + err = request_irq(irq, s3c64xx_dma_irq, 0, "DMA", dmac); + if (err < 0) { + printk(KERN_ERR "%s: failed to get irq\n", __func__); + goto err_clk; + } + + regptr = regs + PL080_Cx_BASE(0); + + for (ch = 0; ch < 8; ch++, chno++, chptr++) { + printk(KERN_INFO "%s: registering DMA %d (%p)\n", + __func__, chno, regptr); + + chptr->bit = 1 << ch; + chptr->number = chno; + chptr->dmac = dmac; + chptr->regs = regptr; + regptr += PL008_Cx_STRIDE; + } + + /* for the moment, permanently enable the controller */ + writel(PL080_CONFIG_ENABLE, regs + PL080_CONFIG); + + printk(KERN_INFO "PL080: IRQ %d, at %p\n", irq, regs); + + return 0; + +err_clk: + clk_disable(dmac->clk); + clk_put(dmac->clk); +err_map: + iounmap(regs); +err_dev: + sysdev_unregister(&dmac->sysdev); +err_alloc: + kfree(dmac); + return err; +} + +static int __init s3c64xx_dma_init(void) +{ + int ret; + + printk(KERN_INFO "%s: Registering DMA channels\n", __func__); + + dma_pool = dma_pool_create("DMA-LLI", NULL, 32, 16, 0); + if (!dma_pool) { + printk(KERN_ERR "%s: failed to create pool\n", __func__); + return -ENOMEM; + } + + ret = sysdev_class_register(&dma_sysclass); + if (ret) { + printk(KERN_ERR "%s: failed to create sysclass\n", __func__); + return -ENOMEM; + } + + /* Set all DMA configuration to be DMA, not SDMA */ + writel(0xffffff, S3C_SYSREG(0x110)); + + /* Register standard DMA controlers */ + s3c64xx_dma_init1(0, DMACH_UART0, IRQ_DMA0, 0x75000000); + s3c64xx_dma_init1(8, DMACH_PCM1_TX, IRQ_DMA1, 0x75100000); + + return 0; +} + +arch_initcall(s3c64xx_dma_init); diff --git a/arch/arm/plat-s3c64xx/gpiolib.c b/arch/arm/plat-s3c64xx/gpiolib.c index 78ee52cffc9e..da7b60ee5e67 100644 --- a/arch/arm/plat-s3c64xx/gpiolib.c +++ b/arch/arm/plat-s3c64xx/gpiolib.c @@ -385,12 +385,19 @@ static __init void s3c64xx_gpiolib_add_4bit(struct s3c_gpio_chip *chip) { chip->chip.direction_input = s3c64xx_gpiolib_4bit_input; chip->chip.direction_output = s3c64xx_gpiolib_4bit_output; + chip->pm = __gpio_pm(&s3c_gpio_pm_4bit); } static __init void s3c64xx_gpiolib_add_4bit2(struct s3c_gpio_chip *chip) { chip->chip.direction_input = s3c64xx_gpiolib_4bit2_input; chip->chip.direction_output = s3c64xx_gpiolib_4bit2_output; + chip->pm = __gpio_pm(&s3c_gpio_pm_4bit); +} + +static __init void s3c64xx_gpiolib_add_2bit(struct s3c_gpio_chip *chip) +{ + chip->pm = __gpio_pm(&s3c_gpio_pm_2bit); } static __init void s3c64xx_gpiolib_add(struct s3c_gpio_chip *chips, @@ -412,7 +419,8 @@ static __init int s3c64xx_gpiolib_init(void) s3c64xx_gpiolib_add(gpio_4bit2, ARRAY_SIZE(gpio_4bit2), s3c64xx_gpiolib_add_4bit2); - s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit), NULL); + s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit), + s3c64xx_gpiolib_add_2bit); return 0; } diff --git a/arch/arm/plat-s3c64xx/include/plat/dma-plat.h b/arch/arm/plat-s3c64xx/include/plat/dma-plat.h new file mode 100644 index 000000000000..0c30dd986725 --- /dev/null +++ b/arch/arm/plat-s3c64xx/include/plat/dma-plat.h @@ -0,0 +1,70 @@ +/* linux/arch/arm/plat-s3c64xx/include/plat/dma-plat.h + * + * Copyright 2009 Openmoko, Inc. + * Copyright 2009 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX DMA core + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define DMACH_LOW_LEVEL (1<<28) /* use this to specifiy hardware ch no */ + +struct s3c64xx_dma_buff; + +/** s3c64xx_dma_buff - S3C64XX DMA buffer descriptor + * @next: Pointer to next buffer in queue or ring. + * @pw: Client provided identifier + * @lli: Pointer to hardware descriptor this buffer is associated with. + * @lli_dma: Hardare address of the descriptor. + */ +struct s3c64xx_dma_buff { + struct s3c64xx_dma_buff *next; + + void *pw; + struct pl080_lli *lli; + dma_addr_t lli_dma; +}; + +struct s3c64xx_dmac; + +struct s3c2410_dma_chan { + unsigned char number; /* number of this dma channel */ + unsigned char in_use; /* channel allocated */ + unsigned char bit; /* bit for enable/disable/etc */ + unsigned char hw_width; + unsigned char peripheral; + + unsigned int flags; + enum s3c2410_dmasrc source; + + + dma_addr_t dev_addr; + + struct s3c2410_dma_client *client; + struct s3c64xx_dmac *dmac; /* pointer to controller */ + + void __iomem *regs; + + /* cdriver callbacks */ + s3c2410_dma_cbfn_t callback_fn; /* buffer done callback */ + s3c2410_dma_opfn_t op_fn; /* channel op callback */ + + /* buffer list and information */ + struct s3c64xx_dma_buff *curr; /* current dma buffer */ + struct s3c64xx_dma_buff *next; /* next buffer to load */ + struct s3c64xx_dma_buff *end; /* end of queue */ + + /* note, when channel is running in circular mode, curr is the + * first buffer enqueued, end is the last and curr is where the + * last buffer-done event is set-at. The buffers are not freed + * and the last buffer hardware descriptor points back to the + * first. + */ +}; + +#include <plat/dma-core.h> diff --git a/arch/arm/plat-s3c64xx/include/plat/irqs.h b/arch/arm/plat-s3c64xx/include/plat/irqs.h index f865bf4d709e..743a70094d04 100644 --- a/arch/arm/plat-s3c64xx/include/plat/irqs.h +++ b/arch/arm/plat-s3c64xx/include/plat/irqs.h @@ -157,6 +157,7 @@ #define S3C_EINT(x) ((x) + S3C_IRQ_EINT_BASE) #define IRQ_EINT(x) S3C_EINT(x) +#define IRQ_EINT_BIT(x) ((x) - S3C_EINT(0)) /* Next the external interrupt groups. These are similar to the IRQ_EINT(x) * that they are sourced from the GPIO pins but with a different scheme for diff --git a/arch/arm/plat-s3c64xx/include/plat/pm-core.h b/arch/arm/plat-s3c64xx/include/plat/pm-core.h new file mode 100644 index 000000000000..d347de3ba0dc --- /dev/null +++ b/arch/arm/plat-s3c64xx/include/plat/pm-core.h @@ -0,0 +1,98 @@ +/* linux/arch/arm/plat-s3c64xx/include/plat/pm-core.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX - PM core support for arch/arm/plat-s3c/pm.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <plat/regs-gpio.h> + +static inline void s3c_pm_debug_init_uart(void) +{ + u32 tmp = __raw_readl(S3C_PCLK_GATE); + + /* As a note, since the S3C64XX UARTs generally have multiple + * clock sources, we simply enable PCLK at the moment and hope + * that the resume settings for the UART are suitable for the + * use with PCLK. + */ + + tmp |= S3C_CLKCON_PCLK_UART0; + tmp |= S3C_CLKCON_PCLK_UART1; + tmp |= S3C_CLKCON_PCLK_UART2; + tmp |= S3C_CLKCON_PCLK_UART3; + + __raw_writel(tmp, S3C_PCLK_GATE); + udelay(10); +} + +static inline void s3c_pm_arch_prepare_irqs(void) +{ + /* VIC should have already been taken care of */ + + /* clear any pending EINT0 interrupts */ + __raw_writel(__raw_readl(S3C64XX_EINT0PEND), S3C64XX_EINT0PEND); +} + +static inline void s3c_pm_arch_stop_clocks(void) +{ +} + +static inline void s3c_pm_arch_show_resume_irqs(void) +{ +} + +/* make these defines, we currently do not have any need to change + * the IRQ wake controls depending on the CPU we are running on */ + +#define s3c_irqwake_eintallow ((1 << 28) - 1) +#define s3c_irqwake_intallow (0) + +static inline void s3c_pm_arch_update_uart(void __iomem *regs, + struct pm_uart_save *save) +{ + u32 ucon = __raw_readl(regs + S3C2410_UCON); + u32 ucon_clk = ucon & S3C6400_UCON_CLKMASK; + u32 save_clk = save->ucon & S3C6400_UCON_CLKMASK; + u32 new_ucon; + u32 delta; + + /* S3C64XX UART blocks only support level interrupts, so ensure that + * when we restore unused UART blocks we force the level interrupt + * settigs. */ + save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL; + + /* We have a constraint on changing the clock type of the UART + * between UCLKx and PCLK, so ensure that when we restore UCON + * that the CLK field is correctly modified if the bootloader + * has changed anything. + */ + if (ucon_clk != save_clk) { + new_ucon = save->ucon; + delta = ucon_clk ^ save_clk; + + /* change from UCLKx => wrong PCLK, + * either UCLK can be tested for by a bit-test + * with UCLK0 */ + if (ucon_clk & S3C6400_UCON_UCLK0 && + !(save_clk & S3C6400_UCON_UCLK0) && + delta & S3C6400_UCON_PCLK2) { + new_ucon &= ~S3C6400_UCON_UCLK0; + } else if (delta == S3C6400_UCON_PCLK2) { + /* as an precaution, don't change from + * PCLK2 => PCLK or vice-versa */ + new_ucon ^= S3C6400_UCON_PCLK2; + } + + S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n", + ucon, new_ucon, save->ucon); + save->ucon = new_ucon; + } +} diff --git a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h index b1082c163247..52836d41e333 100644 --- a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h +++ b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h @@ -32,6 +32,7 @@ #define S3C_HCLK_GATE S3C_CLKREG(0x30) #define S3C_PCLK_GATE S3C_CLKREG(0x34) #define S3C_SCLK_GATE S3C_CLKREG(0x38) +#define S3C_MEM0_GATE S3C_CLKREG(0x3C) /* CLKDIV0 */ #define S3C6400_CLKDIV0_MFC_MASK (0xf << 28) diff --git a/arch/arm/plat-s3c64xx/include/plat/s3c6400.h b/arch/arm/plat-s3c64xx/include/plat/s3c6400.h index 571eaa2e54f1..11f2e1e119b0 100644 --- a/arch/arm/plat-s3c64xx/include/plat/s3c6400.h +++ b/arch/arm/plat-s3c64xx/include/plat/s3c6400.h @@ -15,12 +15,13 @@ /* Common init code for S3C6400 related SoCs */ extern void s3c6400_common_init_uarts(struct s3c2410_uartcfg *cfg, int no); -extern void s3c6400_register_clocks(void); +extern void s3c6400_register_clocks(unsigned armclk_divlimit); extern void s3c6400_setup_clocks(void); #ifdef CONFIG_CPU_S3C6400 extern int s3c6400_init(void); +extern void s3c6400_init_irq(void); extern void s3c6400_map_io(void); extern void s3c6400_init_clocks(int xtal); diff --git a/arch/arm/plat-s3c64xx/irq-eint.c b/arch/arm/plat-s3c64xx/irq-eint.c index 47e5155bb13e..f81b7b818ba0 100644 --- a/arch/arm/plat-s3c64xx/irq-eint.c +++ b/arch/arm/plat-s3c64xx/irq-eint.c @@ -14,6 +14,7 @@ #include <linux/kernel.h> #include <linux/interrupt.h> +#include <linux/sysdev.h> #include <linux/gpio.h> #include <linux/irq.h> #include <linux/io.h> @@ -26,6 +27,7 @@ #include <mach/map.h> #include <plat/cpu.h> +#include <plat/pm.h> #define eint_offset(irq) ((irq) - IRQ_EINT(0)) #define eint_irq_to_bit(irq) (1 << eint_offset(irq)) @@ -134,6 +136,7 @@ static struct irq_chip s3c_irq_eint = { .mask_ack = s3c_irq_eint_maskack, .ack = s3c_irq_eint_ack, .set_type = s3c_irq_eint_set_type, + .set_wake = s3c_irqext_wake, }; /* s3c_irq_demux_eint diff --git a/arch/arm/plat-s3c64xx/irq-pm.c b/arch/arm/plat-s3c64xx/irq-pm.c new file mode 100644 index 000000000000..ca523b5d4c17 --- /dev/null +++ b/arch/arm/plat-s3c64xx/irq-pm.c @@ -0,0 +1,111 @@ +/* arch/arm/plat-s3c64xx/irq-pm.c + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX - Interrupt handling Power Management + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/sysdev.h> +#include <linux/interrupt.h> +#include <linux/serial_core.h> +#include <linux/irq.h> +#include <linux/io.h> + +#include <mach/map.h> + +#include <plat/regs-serial.h> +#include <plat/regs-timer.h> +#include <plat/regs-gpio.h> +#include <plat/cpu.h> +#include <plat/pm.h> + +/* We handled all the IRQ types in this code, to save having to make several + * small files to handle each different type separately. Having the EINT_GRP + * code here shouldn't be as much bloat as the IRQ table space needed when + * they are enabled. The added benefit is we ensure that these registers are + * in the same state as we suspended. + */ + +static struct sleep_save irq_save[] = { + SAVE_ITEM(S3C64XX_PRIORITY), + SAVE_ITEM(S3C64XX_EINT0CON0), + SAVE_ITEM(S3C64XX_EINT0CON1), + SAVE_ITEM(S3C64XX_EINT0FLTCON0), + SAVE_ITEM(S3C64XX_EINT0FLTCON1), + SAVE_ITEM(S3C64XX_EINT0FLTCON2), + SAVE_ITEM(S3C64XX_EINT0FLTCON3), + SAVE_ITEM(S3C64XX_EINT0MASK), + SAVE_ITEM(S3C64XX_TINT_CSTAT), +}; + +static struct irq_grp_save { + u32 fltcon; + u32 con; + u32 mask; +} eint_grp_save[5]; + +static u32 irq_uart_mask[CONFIG_SERIAL_SAMSUNG_UARTS]; + +static int s3c64xx_irq_pm_suspend(struct sys_device *dev, pm_message_t state) +{ + struct irq_grp_save *grp = eint_grp_save; + int i; + + S3C_PMDBG("%s: suspending IRQs\n", __func__); + + s3c_pm_do_save(irq_save, ARRAY_SIZE(irq_save)); + + for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++) + irq_uart_mask[i] = __raw_readl(S3C_VA_UARTx(i) + S3C64XX_UINTM); + + for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) { + grp->con = __raw_readl(S3C64XX_EINT12CON + (i * 4)); + grp->mask = __raw_readl(S3C64XX_EINT12MASK + (i * 4)); + grp->fltcon = __raw_readl(S3C64XX_EINT12FLTCON + (i * 4)); + } + + return 0; +} + +static int s3c64xx_irq_pm_resume(struct sys_device *dev) +{ + struct irq_grp_save *grp = eint_grp_save; + int i; + + S3C_PMDBG("%s: resuming IRQs\n", __func__); + + s3c_pm_do_restore(irq_save, ARRAY_SIZE(irq_save)); + + for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++) + __raw_writel(irq_uart_mask[i], S3C_VA_UARTx(i) + S3C64XX_UINTM); + + for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) { + __raw_writel(grp->con, S3C64XX_EINT12CON + (i * 4)); + __raw_writel(grp->mask, S3C64XX_EINT12MASK + (i * 4)); + __raw_writel(grp->fltcon, S3C64XX_EINT12FLTCON + (i * 4)); + } + + S3C_PMDBG("%s: IRQ configuration restored\n", __func__); + return 0; +} + +static struct sysdev_driver s3c64xx_irq_driver = { + .suspend = s3c64xx_irq_pm_suspend, + .resume = s3c64xx_irq_pm_resume, +}; + +static int __init s3c64xx_irq_pm_init(void) +{ + return sysdev_driver_register(&s3c64xx_sysclass, &s3c64xx_irq_driver); +} + +arch_initcall(s3c64xx_irq_pm_init); + diff --git a/arch/arm/plat-s3c64xx/irq.c b/arch/arm/plat-s3c64xx/irq.c index f22edf7c2d2d..8dc5b6da9789 100644 --- a/arch/arm/plat-s3c64xx/irq.c +++ b/arch/arm/plat-s3c64xx/irq.c @@ -14,12 +14,14 @@ #include <linux/kernel.h> #include <linux/interrupt.h> +#include <linux/serial_core.h> #include <linux/irq.h> #include <linux/io.h> #include <asm/hardware/vic.h> #include <mach/map.h> +#include <plat/regs-serial.h> #include <plat/regs-timer.h> #include <plat/cpu.h> @@ -135,9 +137,6 @@ static inline unsigned int s3c_irq_uart_bit(unsigned int irq) } /* UART interrupt registers, not worth adding to seperate include header */ -#define S3C64XX_UINTP 0x30 -#define S3C64XX_UINTSP 0x34 -#define S3C64XX_UINTM 0x38 static void s3c_irq_uart_mask(unsigned int irq) { @@ -233,8 +232,8 @@ void __init s3c64xx_init_irq(u32 vic0_valid, u32 vic1_valid) printk(KERN_DEBUG "%s: initialising interrupts\n", __func__); /* initialise the pair of VICs */ - vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid); - vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid); + vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid, 0); + vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid, 0); /* add the timer sub-irqs */ diff --git a/arch/arm/plat-s3c64xx/pm.c b/arch/arm/plat-s3c64xx/pm.c new file mode 100644 index 000000000000..07a6516a4f3c --- /dev/null +++ b/arch/arm/plat-s3c64xx/pm.c @@ -0,0 +1,175 @@ +/* linux/arch/arm/plat-s3c64xx/pm.c + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX CPU PM support. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/suspend.h> +#include <linux/serial_core.h> +#include <linux/io.h> + +#include <mach/map.h> + +#include <plat/pm.h> +#include <plat/regs-sys.h> +#include <plat/regs-gpio.h> +#include <plat/regs-clock.h> +#include <plat/regs-syscon-power.h> +#include <plat/regs-gpio-memport.h> + +#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK +#include <plat/gpio-bank-n.h> + +void s3c_pm_debug_smdkled(u32 set, u32 clear) +{ + unsigned long flags; + u32 reg; + + local_irq_save(flags); + reg = __raw_readl(S3C64XX_GPNCON); + reg &= ~(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) | + S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15)); + reg |= S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) | + S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15); + __raw_writel(reg, S3C64XX_GPNCON); + + reg = __raw_readl(S3C64XX_GPNDAT); + reg &= ~(clear << 12); + reg |= set << 12; + __raw_writel(reg, S3C64XX_GPNDAT); + + local_irq_restore(flags); +} +#endif + +static struct sleep_save core_save[] = { + SAVE_ITEM(S3C_APLL_LOCK), + SAVE_ITEM(S3C_MPLL_LOCK), + SAVE_ITEM(S3C_EPLL_LOCK), + SAVE_ITEM(S3C_CLK_SRC), + SAVE_ITEM(S3C_CLK_DIV0), + SAVE_ITEM(S3C_CLK_DIV1), + SAVE_ITEM(S3C_CLK_DIV2), + SAVE_ITEM(S3C_CLK_OUT), + SAVE_ITEM(S3C_HCLK_GATE), + SAVE_ITEM(S3C_PCLK_GATE), + SAVE_ITEM(S3C_SCLK_GATE), + SAVE_ITEM(S3C_MEM0_GATE), + + SAVE_ITEM(S3C_EPLL_CON1), + SAVE_ITEM(S3C_EPLL_CON0), + + SAVE_ITEM(S3C64XX_MEM0DRVCON), + SAVE_ITEM(S3C64XX_MEM1DRVCON), + +#ifndef CONFIG_CPU_FREQ + SAVE_ITEM(S3C_APLL_CON), + SAVE_ITEM(S3C_MPLL_CON), +#endif +}; + +static struct sleep_save misc_save[] = { + SAVE_ITEM(S3C64XX_AHB_CON0), + SAVE_ITEM(S3C64XX_AHB_CON1), + SAVE_ITEM(S3C64XX_AHB_CON2), + + SAVE_ITEM(S3C64XX_SPCON), + + SAVE_ITEM(S3C64XX_MEM0CONSTOP), + SAVE_ITEM(S3C64XX_MEM1CONSTOP), + SAVE_ITEM(S3C64XX_MEM0CONSLP0), + SAVE_ITEM(S3C64XX_MEM0CONSLP1), + SAVE_ITEM(S3C64XX_MEM1CONSLP), +}; + +void s3c_pm_configure_extint(void) +{ + __raw_writel(s3c_irqwake_eintmask, S3C64XX_EINT_MASK); +} + +void s3c_pm_restore_core(void) +{ + __raw_writel(0, S3C64XX_EINT_MASK); + + s3c_pm_debug_smdkled(1 << 2, 0); + + s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save)); + s3c_pm_do_restore(misc_save, ARRAY_SIZE(misc_save)); +} + +void s3c_pm_save_core(void) +{ + s3c_pm_do_save(misc_save, ARRAY_SIZE(misc_save)); + s3c_pm_do_save(core_save, ARRAY_SIZE(core_save)); +} + +/* since both s3c6400 and s3c6410 share the same sleep pm calls, we + * put the per-cpu code in here until any new cpu comes along and changes + * this. + */ + +#include <plat/regs-gpio.h> + +static void s3c64xx_cpu_suspend(void) +{ + unsigned long tmp; + + /* set our standby method to sleep */ + + tmp = __raw_readl(S3C64XX_PWR_CFG); + tmp &= ~S3C64XX_PWRCFG_CFG_WFI_MASK; + tmp |= S3C64XX_PWRCFG_CFG_WFI_SLEEP; + __raw_writel(tmp, S3C64XX_PWR_CFG); + + /* clear any old wakeup */ + + __raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), + S3C64XX_WAKEUP_STAT); + + /* set the LED state to 0110 over sleep */ + s3c_pm_debug_smdkled(3 << 1, 0xf); + + /* issue the standby signal into the pm unit. Note, we + * issue a write-buffer drain just in case */ + + tmp = 0; + + asm("b 1f\n\t" + ".align 5\n\t" + "1:\n\t" + "mcr p15, 0, %0, c7, c10, 5\n\t" + "mcr p15, 0, %0, c7, c10, 4\n\t" + "mcr p15, 0, %0, c7, c0, 4" :: "r" (tmp)); + + /* we should never get past here */ + + panic("sleep resumed to originator?"); +} + +static void s3c64xx_pm_prepare(void) +{ + /* store address of resume. */ + __raw_writel(virt_to_phys(s3c_cpu_resume), S3C64XX_INFORM0); + + /* ensure previous wakeup state is cleared before sleeping */ + __raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), S3C64XX_WAKEUP_STAT); +} + +static int s3c64xx_pm_init(void) +{ + pm_cpu_prep = s3c64xx_pm_prepare; + pm_cpu_sleep = s3c64xx_cpu_suspend; + pm_uart_udivslot = 1; + return 0; +} + +arch_initcall(s3c64xx_pm_init); diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 05b17528041e..1debc1f9f987 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -133,6 +133,65 @@ static struct clksrc_clk clk_mout_mpll = { .sources = &clk_src_mpll, }; +static unsigned int armclk_mask; + +static unsigned long s3c64xx_clk_arm_get_rate(struct clk *clk) +{ + unsigned long rate = clk_get_rate(clk->parent); + u32 clkdiv; + + /* divisor mask starts at bit0, so no need to shift */ + clkdiv = __raw_readl(S3C_CLK_DIV0) & armclk_mask; + + return rate / (clkdiv + 1); +} + +static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk, + unsigned long rate) +{ + unsigned long parent = clk_get_rate(clk->parent); + u32 div; + + if (parent < rate) + return rate; + + div = (parent / rate) - 1; + if (div > armclk_mask) + div = armclk_mask; + + return parent / (div + 1); +} + +static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate) +{ + unsigned long parent = clk_get_rate(clk->parent); + u32 div; + u32 val; + + if (rate < parent / (armclk_mask + 1)) + return -EINVAL; + + rate = clk_round_rate(clk, rate); + div = clk_get_rate(clk->parent) / rate; + + val = __raw_readl(S3C_CLK_DIV0); + val &= armclk_mask; + val |= (div - 1); + __raw_writel(val, S3C_CLK_DIV0); + + return 0; + +} + +static struct clk clk_arm = { + .name = "armclk", + .id = -1, + .parent = &clk_mout_apll.clk, + .get_rate = s3c64xx_clk_arm_get_rate, + .set_rate = s3c64xx_clk_arm_set_rate, + .round_rate = s3c64xx_clk_arm_round_rate, +}; + static unsigned long s3c64xx_clk_doutmpll_get_rate(struct clk *clk) { unsigned long rate = clk_get_rate(clk->parent); @@ -520,6 +579,33 @@ static struct clksrc_clk clk_irda = { .reg_divider = S3C_CLK_DIV2, }; +static struct clk *clkset_camif_list[] = { + &clk_h2, +}; + +static struct clk_sources clkset_camif = { + .sources = clkset_camif_list, + .nr_sources = ARRAY_SIZE(clkset_camif_list), +}; + +static struct clksrc_clk clk_camif = { + .clk = { + .name = "camera", + .id = -1, + .ctrlbit = S3C_CLKCON_SCLK_CAM, + .enable = s3c64xx_sclk_ctrl, + .set_parent = s3c64xx_setparent_clksrc, + .get_rate = s3c64xx_getrate_clksrc, + .set_rate = s3c64xx_setrate_clksrc, + .round_rate = s3c64xx_roundrate_clksrc, + }, + .shift = 0, + .mask = 0, + .sources = &clkset_camif, + .divider_shift = S3C6400_CLKDIV0_CAM_SHIFT, + .reg_divider = S3C_CLK_DIV0, +}; + /* Clock initialisation code */ static struct clksrc_clk *init_parents[] = { @@ -536,6 +622,7 @@ static struct clksrc_clk *init_parents[] = { &clk_audio0, &clk_audio1, &clk_irda, + &clk_camif, }; static void __init_or_cpufreq s3c6400_set_clksrc(struct clksrc_clk *clk) @@ -608,6 +695,7 @@ void __init_or_cpufreq s3c6400_setup_clocks(void) clk_fout_epll.rate = epll; clk_fout_apll.rate = apll; + clk_h2.rate = hclk2; clk_h.rate = hclk; clk_p.rate = pclk; clk_f.rate = fclk; @@ -635,14 +723,30 @@ static struct clk *clks[] __initdata = { &clk_audio0.clk, &clk_audio1.clk, &clk_irda.clk, + &clk_camif.clk, + &clk_arm, }; -void __init s3c6400_register_clocks(void) +/** + * s3c6400_register_clocks - register clocks for s3c6400 and above + * @armclk_divlimit: Divisor mask for ARMCLK + * + * Register the clocks for the S3C6400 and above SoC range, such + * as ARMCLK and the clocks which have divider chains attached. + * + * This call does not setup the clocks, which is left to the + * s3c6400_setup_clocks() call which may be needed by the cpufreq + * or resume code to re-set the clocks if the bootloader has changed + * them. + */ +void __init s3c6400_register_clocks(unsigned armclk_divlimit) { struct clk *clkp; int ret; int ptr; + armclk_mask = armclk_divlimit; + for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) { clkp = clks[ptr]; ret = s3c24xx_register_clock(clkp); diff --git a/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c b/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c new file mode 100644 index 000000000000..5417123b0ac1 --- /dev/null +++ b/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c @@ -0,0 +1,55 @@ +/* linux/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c + * + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX - Helper functions for setting up SDHCI device(s) GPIO (HSMMC) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/io.h> + +#include <mach/gpio.h> +#include <plat/gpio-cfg.h> + +void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width) +{ + unsigned int gpio; + unsigned int end; + + end = S3C64XX_GPG(2 + width); + + /* Set all the necessary GPG pins to special-function 0 */ + for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) { + s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); + s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); + } + + s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP); + s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2)); +} + +void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width) +{ + unsigned int gpio; + unsigned int end; + + end = S3C64XX_GPH(2 + width); + + /* Set all the necessary GPG pins to special-function 0 */ + for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) { + s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); + s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); + } + + s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP); + s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3)); +} diff --git a/arch/arm/plat-s3c64xx/sleep.S b/arch/arm/plat-s3c64xx/sleep.S new file mode 100644 index 000000000000..8e71fe90a373 --- /dev/null +++ b/arch/arm/plat-s3c64xx/sleep.S @@ -0,0 +1,144 @@ +/* linux/0arch/arm/plat-s3c64xx/sleep.S + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C64XX CPU sleep code + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/linkage.h> +#include <asm/assembler.h> +#include <mach/map.h> + +#undef S3C64XX_VA_GPIO +#define S3C64XX_VA_GPIO (0x0) + +#include <plat/regs-gpio.h> +#include <plat/gpio-bank-n.h> + +#define LL_UART (S3C_PA_UART + (0x400 * CONFIG_S3C_LOWLEVEL_UART_PORT)) + + .text + + /* s3c_cpu_save + * + * Save enough processor state to allow the restart of the pm.c + * code after resume. + * + * entry: + * r0 = pointer to the save block + */ + +ENTRY(s3c_cpu_save) + stmfd sp!, { r4 - r12, lr } + + mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID + mrc p15, 0, r5, c3, c0, 0 @ Domain ID + mrc p15, 0, r6, c2, c0, 0 @ Translation Table BASE0 + mrc p15, 0, r7, c2, c0, 1 @ Translation Table BASE1 + mrc p15, 0, r8, c2, c0, 2 @ Translation Table Control + mrc p15, 0, r9, c1, c0, 0 @ Control register + mrc p15, 0, r10, c1, c0, 1 @ Auxiliary control register + mrc p15, 0, r11, c1, c0, 2 @ Co-processor access controls + + stmia r0, { r4 - r13 } @ Save CP registers and SP + + @@ save our state to ram + bl s3c_pm_cb_flushcache + + @@ call final suspend code + ldr r0, =pm_cpu_sleep + ldr pc, [r0] + + @@ return to the caller, after the MMU is turned on. + @@ restore the last bits of the stack and return. +resume_with_mmu: + ldmfd sp!, { r4 - r12, pc } @ return, from sp from s3c_cpu_save + + .data + + /* the next bit is code, but it requires easy access to the + * s3c_sleep_save_phys data before the MMU is switched on, so + * we store the code that needs this variable in the .data where + * the value can be written to (the .text segment is RO). + */ + + .global s3c_sleep_save_phys +s3c_sleep_save_phys: + .word 0 + + /* Sleep magic, the word before the resume entry point so that the + * bootloader can check for a resumeable image. */ + + .word 0x2bedf00d + + /* s3c_cpu_reusme + * + * This is the entry point, stored by whatever method the bootloader + * requires to get the kernel runnign again. This code expects to be + * entered with no caches live and the MMU disabled. It will then + * restore the MMU and other basic CP registers saved and restart + * the kernel C code to finish the resume code. + */ + +ENTRY(s3c_cpu_resume) + msr cpsr_c, #PSR_I_BIT | PSR_F_BIT | SVC_MODE + ldr r2, =LL_UART /* for debug */ + +#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK + /* Initialise the GPIO state if we are debugging via the SMDK LEDs, + * as the uboot version supplied resets these to inputs during the + * resume checks. + */ + + ldr r3, =S3C64XX_PA_GPIO + ldr r0, [ r3, #S3C64XX_GPNCON ] + bic r0, r0, #(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) | \ + S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15)) + orr r0, r0, #(S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) | \ + S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15)) + str r0, [ r3, #S3C64XX_GPNCON ] + + ldr r0, [ r3, #S3C64XX_GPNDAT ] + bic r0, r0, #0xf << 12 @ GPN12..15 + orr r0, r0, #1 << 15 @ GPN15 + str r0, [ r3, #S3C64XX_GPNDAT ] +#endif + + /* __v6_setup from arch/arm/mm/proc-v6.S, ensure that the caches + * are thoroughly cleaned just in case the bootloader didn't do it + * for us. */ + mov r0, #0 + mcr p15, 0, r0, c7, c14, 0 @ clean+invalidate D cache + mcr p15, 0, r0, c7, c5, 0 @ invalidate I cache + mcr p15, 0, r0, c7, c15, 0 @ clean+invalidate cache + mcr p15, 0, r0, c7, c10, 4 @ drain write buffer + @@mcr p15, 0, r0, c8, c7, 0 @ invalidate I + D TLBs + @@mcr p15, 0, r0, c7, c7, 0 @ Invalidate I + D caches + + ldr r0, s3c_sleep_save_phys + ldmia r0, { r4 - r13 } + + mcr p15, 0, r4, c13, c0, 0 @ FCSE/PID + mcr p15, 0, r5, c3, c0, 0 @ Domain ID + mcr p15, 0, r6, c2, c0, 0 @ Translation Table BASE0 + mcr p15, 0, r7, c2, c0, 1 @ Translation Table BASE1 + mcr p15, 0, r8, c2, c0, 2 @ Translation Table Control + mcr p15, 0, r10, c1, c0, 1 @ Auxiliary control register + + mov r0, #0 @ restore copro access controls + mcr p15, 0, r11, c1, c0, 2 @ Co-processor access controls + mcr p15, 0, r0, c7, c5, 4 + + ldr r2, =resume_with_mmu + mcr p15, 0, r9, c1, c0, 0 /* turn mmu back on */ + nop + mov pc, r2 /* jump back */ + + .end diff --git a/drivers/leds/leds-h1940.c b/drivers/leds/leds-h1940.c index 1aa46a390a0d..173d104d9ff2 100644 --- a/drivers/leds/leds-h1940.c +++ b/drivers/leds/leds-h1940.c @@ -16,6 +16,8 @@ #include <linux/string.h> #include <linux/ctype.h> #include <linux/leds.h> +#include <linux/gpio.h> + #include <mach/regs-gpio.h> #include <mach/hardware.h> #include <mach/h1940-latch.h> diff --git a/drivers/leds/leds-s3c24xx.c b/drivers/leds/leds-s3c24xx.c index aa2e7ae0cdae..aa7acf3b9224 100644 --- a/drivers/leds/leds-s3c24xx.c +++ b/drivers/leds/leds-s3c24xx.c @@ -15,6 +15,7 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/leds.h> +#include <linux/gpio.h> #include <mach/hardware.h> #include <mach/regs-gpio.h> diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 2db166b7096f..4eb4f37544ab 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -17,6 +17,7 @@ #include <linux/mmc/host.h> #include <linux/platform_device.h> #include <linux/cpufreq.h> +#include <linux/gpio.h> #include <linux/irq.h> #include <linux/io.h> @@ -789,7 +790,7 @@ static void s3cmci_dma_setup(struct s3cmci_host *host, last_source = source; - s3c2410_dma_devconfig(host->dma, source, 3, + s3c2410_dma_devconfig(host->dma, source, host->mem->start + host->sdidata); if (!setup_ok) { @@ -1121,7 +1122,7 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) case MMC_POWER_OFF: default: s3c2410_gpio_setpin(S3C2410_GPE5, 0); - s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP); + s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPIO_OUTPUT); if (host->is2440) mci_con |= S3C2440_SDICON_SDRESET; diff --git a/drivers/spi/spi_s3c24xx_gpio.c b/drivers/spi/spi_s3c24xx_gpio.c index f2447a5476bb..bbf9371cd284 100644 --- a/drivers/spi/spi_s3c24xx_gpio.c +++ b/drivers/spi/spi_s3c24xx_gpio.c @@ -17,6 +17,7 @@ #include <linux/spinlock.h> #include <linux/workqueue.h> #include <linux/platform_device.h> +#include <linux/gpio.h> #include <linux/spi/spi.h> #include <linux/spi/spi_bitbang.h> diff --git a/sound/soc/s3c24xx/s3c2412-i2s.c b/sound/soc/s3c24xx/s3c2412-i2s.c index b7e0b3f0bfc8..c35b74b2d1da 100644 --- a/sound/soc/s3c24xx/s3c2412-i2s.c +++ b/sound/soc/s3c24xx/s3c2412-i2s.c @@ -20,6 +20,7 @@ #include <linux/module.h> #include <linux/device.h> #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/clk.h> #include <linux/kernel.h> #include <linux/io.h> diff --git a/sound/soc/s3c24xx/s3c2443-ac97.c b/sound/soc/s3c24xx/s3c2443-ac97.c index 3698f707c44d..3f03d5ddfacd 100644 --- a/sound/soc/s3c24xx/s3c2443-ac97.c +++ b/sound/soc/s3c24xx/s3c2443-ac97.c @@ -19,6 +19,7 @@ #include <linux/io.h> #include <linux/wait.h> #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/clk.h> #include <sound/core.h> diff --git a/sound/soc/s3c24xx/s3c24xx-i2s.c b/sound/soc/s3c24xx/s3c24xx-i2s.c index cc066964dad6..556e35f0ab73 100644 --- a/sound/soc/s3c24xx/s3c24xx-i2s.c +++ b/sound/soc/s3c24xx/s3c24xx-i2s.c @@ -21,6 +21,8 @@ #include <linux/clk.h> #include <linux/jiffies.h> #include <linux/io.h> +#include <linux/gpio.h> + #include <sound/core.h> #include <sound/pcm.h> #include <sound/pcm_params.h> diff --git a/sound/soc/s3c24xx/s3c24xx-pcm.c b/sound/soc/s3c24xx/s3c24xx-pcm.c index 169ddad31575..eecfa5eba06b 100644 --- a/sound/soc/s3c24xx/s3c24xx-pcm.c +++ b/sound/soc/s3c24xx/s3c24xx-pcm.c @@ -218,24 +218,17 @@ static int s3c24xx_pcm_prepare(struct snd_pcm_substream *substream) * sync to pclk, half-word transfers to the IIS-FIFO. */ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { s3c2410_dma_devconfig(prtd->params->channel, - S3C2410_DMASRC_MEM, S3C2410_DISRCC_INC | - S3C2410_DISRCC_APB, prtd->params->dma_addr); - - s3c2410_dma_config(prtd->params->channel, - prtd->params->dma_size, - S3C2410_DCON_SYNC_PCLK | - S3C2410_DCON_HANDSHAKE); + S3C2410_DMASRC_MEM, + prtd->params->dma_addr); } else { - s3c2410_dma_config(prtd->params->channel, - prtd->params->dma_size, - S3C2410_DCON_HANDSHAKE | - S3C2410_DCON_SYNC_PCLK); - s3c2410_dma_devconfig(prtd->params->channel, - S3C2410_DMASRC_HW, 0x3, - prtd->params->dma_addr); + S3C2410_DMASRC_HW, + prtd->params->dma_addr); } + s3c2410_dma_config(prtd->params->channel, + prtd->params->dma_size); + /* flush the DMA channel */ s3c2410_dma_ctrl(prtd->params->channel, S3C2410_DMAOP_FLUSH); prtd->dma_loaded = 0; |