summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--drivers/tty/serial/icom.c4
-rw-r--r--drivers/tty/serial/pch_uart.c10
-rw-r--r--drivers/tty/serial/samsung.c8
3 files changed, 16 insertions, 6 deletions
diff --git a/drivers/tty/serial/icom.c b/drivers/tty/serial/icom.c
index d98e43348970..67423805e6d9 100644
--- a/drivers/tty/serial/icom.c
+++ b/drivers/tty/serial/icom.c
@@ -455,11 +455,11 @@ static void load_code(struct icom_port *icom_port)
for (index = 0; index < fw->size; index++)
new_page[index] = fw->data[index];
- release_firmware(fw);
-
writeb((char) ((fw->size + 16)/16), &icom_port->dram->mac_length);
writel(temp_pci, &icom_port->dram->mac_load_addr);
+ release_firmware(fw);
+
/*Setting the syncReg to 0x80 causes adapter to start downloading
the personality code into adapter instruction RAM.
Once code is loaded, it will begin executing and, based on
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index 9cbd3acaf37f..8fa1134e0051 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -1508,10 +1508,14 @@ static int pch_uart_verify_port(struct uart_port *port,
__func__);
return -EOPNOTSUPP;
#endif
- dev_info(priv->port.dev, "PCH UART : Use DMA Mode\n");
- if (!priv->use_dma)
+ if (!priv->use_dma) {
pch_request_dma(port);
- priv->use_dma = 1;
+ if (priv->chan_rx)
+ priv->use_dma = 1;
+ }
+ dev_info(priv->port.dev, "PCH UART: %s\n",
+ priv->use_dma ?
+ "Use DMA Mode" : "No DMA");
}
return 0;
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index c1af04d46682..9cd706df3b33 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1209,7 +1209,6 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
/* reset the fifos (and setup the uart) */
s3c24xx_serial_resetport(port, cfg);
- clk_disable_unprepare(ourport->clk);
return 0;
}
@@ -1287,6 +1286,13 @@ static int s3c24xx_serial_probe(struct platform_device *pdev)
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
platform_set_drvdata(pdev, &ourport->port);
+ /*
+ * Deactivate the clock enabled in s3c24xx_serial_init_port here,
+ * so that a potential re-enablement through the pm-callback overlaps
+ * and keeps the clock enabled in this case.
+ */
+ clk_disable_unprepare(ourport->clk);
+
#ifdef CONFIG_SAMSUNG_CLOCK
ret = device_create_file(&pdev->dev, &dev_attr_clock_source);
if (ret < 0)