Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next

Jonathan writes:

1st set of IIO new device support, features and cleanup for 5.17

Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.

Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.

New device support
* adi,ad7293
  - New driver and bindings for this Power Amplifier drain current
    controller.  A complex device with various related monitoring functions.
* adi,ad75513R
  - New driver and bindings for this combined ADC and DAC device.
  - A few follow up fixes.
* adi,admv8818
  - New driver (and type) for this 2-18GHz filter device. Includes
    bindings and ABI documentation to allow clk_notifier based auto
    adjustment of the filters in appropriate applications.
* liteon,ltr501
  - Support for the ltr303.  ID and chip specific info table.
* xilinx,ams
  - New generic firmware function fwnode_iomap() as used in this driver.
  - New driver and bindings for this ADC and on-chip sensors as found
    in various Xilinx devices.

Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
  form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
  is called but no trigger consumers are actually enabled and hence the
  trigger may be reenabled from the interrupt handler.  Seen in the wild
  on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.

Tests/tools
* format_value
  - Check against NULL returns from allocations in tests.
  - Add IIO_VAL_INT_64 test case.
* event_monitor
  - Flush the output after event to given more consistent latency
    when tool output piped to other programs.

Driver Features
* axp20x
  - Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
  - Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
  - Add proximity-near-level support and dt-binding.

Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
  and then stop assigning it to allow this to be used for other purposes.
  We can always get to the indio_dev using dev_to_iio_dev() which is
  a container_of() based approach. Also cleanup up some related unnecessary
  convoluted cases.
  - atmel,at91-sam5d2
  - nxp,imx7d
  - meas,ms5611
  - st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
  in place of a second copy for read_raw and similar paths.
  - adi,ad7266
  - bosch,bma220
  - fsl,mac3110
  - fsl,mma7455
  - fsl,mpl3115
  - kionix,kcjk-1013
  - sensortek,stk8ba50
  - sensortek,stk8312
  - ti,adc12138
  - ti,ads1015
  - vti,sca3000
  - xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
  header changes to avoid including of.h
  - Various DACs had false CONFIG_OF dependencies.
  - dpot-dac
  - envelope-detector
  - adi,ad5755
  - adi,ad5758
  - capella,cm3605
  - maxim,max9611
  - microchip,mcp41010
  - microchip,mcp3911
  - ti,adc12138
* Trivial clang warning fixes for W=1 warnings.

Driver specific cleanup and minor fixes
* adi,ad7606
  - Comment fixes.
* ams,ad3935
  - Drop pointless cast to the same type.
* atmel,at91-sama5d2
  - Fix wrong cast of iio_dev->dev to platform_device that happened to
    be harmless.
* fsl,mma7660
  - Stop i2c remove() function returning an error code. Part of a rework
    to eventually stop returning anything from these.
* fsl,mma8452
  - Use correct type for local irqreturn_t.
* nxp,imx8mq
  - Maintainer email address update.
* nxp,lpc18xx_adc
  - Ensure clk_prepare_enable() called before clk_get_rate().
  - Switch of.h for mod_devicetable.h to reflect no of specific functions,
    just the id table.
* renesas,rzg2l
  - Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
  - Drop pointless cast.
* st,lsm6dsx
  - Make it possible to disable the sensorhub from DT to avoid a corner
    case where the address of a slave device many be accidentally modified.
* st,stm32-adc
  - Stop leaking an of_node in an error path.
* st,stmp2
   - Avoid wrong sized type for bit field which could result in
     over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
  - Put back some ACPI support for non standards compliant ADC081C
    ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
  - Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
  - Use helper macro kthread_run() to replace some boilerplate.
  - Avoid double reference counting.
  - Drop pointless cast.
* xilinx,xadc
  - Make the IRQ optional as not always wired to the host system.

* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
  iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
  iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
  MAINTAINERS: Add maintainer for xilinx-ams
  dt-bindings: iio: adc: Add Xilinx AMS binding documentation
  iio: adc: Add Xilinx AMS driver
  device property: Add fwnode_iomap()
  iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
  iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
  iio:dummy: Drop set but unused variable len.
  iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
  iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
  iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
  iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
  iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
  iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
  drivers:iio:dac: Add AD3552R driver support
  dt-bindings: iio: dac: Add adi,ad3552r.yaml
  ...

7 files changed, 29 insertions, 109 deletions

diff --git a/include/dt-bindings/iio/addac/adi,ad74413r.h b/include/dt-bindings/iio/addac/adi,ad74413r.h
new file mode 100644
index 000000000000..204f92bbd79f
--- /dev/null
+++ b/include/dt-bindings/iio/addac/adi,ad74413r.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _DT_BINDINGS_ADI_AD74413R_H
+#define _DT_BINDINGS_ADI_AD74413R_H
+
+#define CH_FUNC_HIGH_IMPEDANCE			0x0
+#define CH_FUNC_VOLTAGE_OUTPUT			0x1
+#define CH_FUNC_CURRENT_OUTPUT			0x2
+#define CH_FUNC_VOLTAGE_INPUT			0x3
+#define CH_FUNC_CURRENT_INPUT_EXT_POWER		0x4
+#define CH_FUNC_CURRENT_INPUT_LOOP_POWER	0x5
+#define CH_FUNC_RESISTANCE_INPUT		0x6
+#define CH_FUNC_DIGITAL_INPUT_LOGIC		0x7
+#define CH_FUNC_DIGITAL_INPUT_LOOP_POWER	0x8
+#define CH_FUNC_CURRENT_INPUT_EXT_POWER_HART	0x9
+#define CH_FUNC_CURRENT_INPUT_LOOP_POWER_HART	0xA
+
+#define CH_FUNC_MIN	CH_FUNC_HIGH_IMPEDANCE
+#define CH_FUNC_MAX	CH_FUNC_CURRENT_INPUT_LOOP_POWER_HART
+
+#endif /* _DT_BINDINGS_ADI_AD74413R_H */
diff --git a/include/linux/iio/buffer-dma.h b/include/linux/iio/buffer-dma.h
index ff15c61bf319..6564bdcdac66 100644
--- a/include/linux/iio/buffer-dma.h
+++ b/include/linux/iio/buffer-dma.h
@@ -17,11 +17,6 @@ struct iio_dma_buffer_queue;
 struct iio_dma_buffer_ops;
 struct device;
 
-struct iio_buffer_block {
-	u32 size;
-	u32 bytes_used;
-};
-
 /**
  * enum iio_block_state - State of a struct iio_dma_buffer_block
  * @IIO_BLOCK_STATE_DEQUEUED: Block is not queued
diff --git a/include/linux/iio/iio.h b/include/linux/iio/iio.h
index 324561b7a5e8..07025d6b3de1 100644
--- a/include/linux/iio/iio.h
+++ b/include/linux/iio/iio.h
@@ -103,15 +103,16 @@ ssize_t iio_enum_write(struct iio_dev *indio_dev,
 /**
  * IIO_ENUM_AVAILABLE() - Initialize enum available extended channel attribute
  * @_name:	Attribute name ("_available" will be appended to the name)
+ * @_shared:	Whether the attribute is shared between all channels
  * @_e:		Pointer to an iio_enum struct
  *
  * Creates a read only attribute which lists all the available enum items in a
  * space separated list. This should usually be used together with IIO_ENUM()
  */
-#define IIO_ENUM_AVAILABLE(_name, _e) \
+#define IIO_ENUM_AVAILABLE(_name, _shared, _e) \
 { \
 	.name = (_name "_available"), \
-	.shared = IIO_SHARED_BY_TYPE, \
+	.shared = _shared, \
 	.read = iio_enum_available_read, \
 	.private = (uintptr_t)(_e), \
 }
diff --git a/include/linux/iio/trigger.h b/include/linux/iio/trigger.h
index 096f68dd2e0c..4c69b144677b 100644
--- a/include/linux/iio/trigger.h
+++ b/include/linux/iio/trigger.h
@@ -55,6 +55,7 @@ struct iio_trigger_ops {
  * @attached_own_device:[INTERN] if we are using our own device as trigger,
  *			i.e. if we registered a poll function to the same
  *			device as the one providing the trigger.
+ * @reenable_work:	[INTERN] work item used to ensure reenable can sleep.
  **/
 struct iio_trigger {
 	const struct iio_trigger_ops	*ops;
@@ -74,6 +75,7 @@ struct iio_trigger {
 	unsigned long pool[BITS_TO_LONGS(CONFIG_IIO_CONSUMERS_PER_TRIGGER)];
 	struct mutex			pool_lock;
 	bool				attached_own_device;
+	struct work_struct		reenable_work;
 };
 
 
diff --git a/include/linux/iio/types.h b/include/linux/iio/types.h
index 84b3f8175cc6..a7aa91f3a8dc 100644
--- a/include/linux/iio/types.h
+++ b/include/linux/iio/types.h
@@ -24,6 +24,7 @@ enum iio_event_info {
 #define IIO_VAL_INT_PLUS_NANO 3
 #define IIO_VAL_INT_PLUS_MICRO_DB 4
 #define IIO_VAL_INT_MULTIPLE 5
+#define IIO_VAL_INT_64 6 /* 64-bit data, val is lower 32 bits */
 #define IIO_VAL_FRACTIONAL 10
 #define IIO_VAL_FRACTIONAL_LOG2 11
 #define IIO_VAL_CHAR 12
diff --git a/include/linux/platform_data/ad5755.h b/include/linux/platform_data/ad5755.h
deleted file mode 100644
index e371e08f04bc..000000000000
--- a/include/linux/platform_data/ad5755.h
+++ /dev/null
@@ -1,102 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright 2012 Analog Devices Inc.
- */
-#ifndef __LINUX_PLATFORM_DATA_AD5755_H__
-#define __LINUX_PLATFORM_DATA_AD5755_H__
-
-enum ad5755_mode {
-	AD5755_MODE_VOLTAGE_0V_5V		= 0,
-	AD5755_MODE_VOLTAGE_0V_10V		= 1,
-	AD5755_MODE_VOLTAGE_PLUSMINUS_5V	= 2,
-	AD5755_MODE_VOLTAGE_PLUSMINUS_10V	= 3,
-	AD5755_MODE_CURRENT_4mA_20mA		= 4,
-	AD5755_MODE_CURRENT_0mA_20mA		= 5,
-	AD5755_MODE_CURRENT_0mA_24mA		= 6,
-};
-
-enum ad5755_dc_dc_phase {
-	AD5755_DC_DC_PHASE_ALL_SAME_EDGE		= 0,
-	AD5755_DC_DC_PHASE_A_B_SAME_EDGE_C_D_OPP_EDGE	= 1,
-	AD5755_DC_DC_PHASE_A_C_SAME_EDGE_B_D_OPP_EDGE	= 2,
-	AD5755_DC_DC_PHASE_90_DEGREE			= 3,
-};
-
-enum ad5755_dc_dc_freq {
-	AD5755_DC_DC_FREQ_250kHZ = 0,
-	AD5755_DC_DC_FREQ_410kHZ = 1,
-	AD5755_DC_DC_FREQ_650kHZ = 2,
-};
-
-enum ad5755_dc_dc_maxv {
-	AD5755_DC_DC_MAXV_23V	= 0,
-	AD5755_DC_DC_MAXV_24V5	= 1,
-	AD5755_DC_DC_MAXV_27V	= 2,
-	AD5755_DC_DC_MAXV_29V5	= 3,
-};
-
-enum ad5755_slew_rate {
-	AD5755_SLEW_RATE_64k	= 0,
-	AD5755_SLEW_RATE_32k	= 1,
-	AD5755_SLEW_RATE_16k	= 2,
-	AD5755_SLEW_RATE_8k	= 3,
-	AD5755_SLEW_RATE_4k	= 4,
-	AD5755_SLEW_RATE_2k	= 5,
-	AD5755_SLEW_RATE_1k	= 6,
-	AD5755_SLEW_RATE_500	= 7,
-	AD5755_SLEW_RATE_250	= 8,
-	AD5755_SLEW_RATE_125	= 9,
-	AD5755_SLEW_RATE_64	= 10,
-	AD5755_SLEW_RATE_32	= 11,
-	AD5755_SLEW_RATE_16	= 12,
-	AD5755_SLEW_RATE_8	= 13,
-	AD5755_SLEW_RATE_4	= 14,
-	AD5755_SLEW_RATE_0_5	= 15,
-};
-
-enum ad5755_slew_step_size {
-	AD5755_SLEW_STEP_SIZE_1 = 0,
-	AD5755_SLEW_STEP_SIZE_2 = 1,
-	AD5755_SLEW_STEP_SIZE_4 = 2,
-	AD5755_SLEW_STEP_SIZE_8 = 3,
-	AD5755_SLEW_STEP_SIZE_16 = 4,
-	AD5755_SLEW_STEP_SIZE_32 = 5,
-	AD5755_SLEW_STEP_SIZE_64 = 6,
-	AD5755_SLEW_STEP_SIZE_128 = 7,
-	AD5755_SLEW_STEP_SIZE_256 = 8,
-};
-
-/**
- * struct ad5755_platform_data - AD5755 DAC driver platform data
- * @ext_dc_dc_compenstation_resistor: Whether an external DC-DC converter
- * compensation register is used.
- * @dc_dc_phase: DC-DC converter phase.
- * @dc_dc_freq: DC-DC converter frequency.
- * @dc_dc_maxv: DC-DC maximum allowed boost voltage.
- * @dac.mode: The mode to be used for the DAC output.
- * @dac.ext_current_sense_resistor: Whether an external current sense resistor
- * is used.
- * @dac.enable_voltage_overrange: Whether to enable 20% voltage output overrange.
- * @dac.slew.enable: Whether to enable digital slew.
- * @dac.slew.rate: Slew rate of the digital slew.
- * @dac.slew.step_size: Slew step size of the digital slew.
- **/
-struct ad5755_platform_data {
-	bool ext_dc_dc_compenstation_resistor;
-	enum ad5755_dc_dc_phase dc_dc_phase;
-	enum ad5755_dc_dc_freq dc_dc_freq;
-	enum ad5755_dc_dc_maxv dc_dc_maxv;
-
-	struct {
-		enum ad5755_mode mode;
-		bool ext_current_sense_resistor;
-		bool enable_voltage_overrange;
-		struct {
-			bool enable;
-			enum ad5755_slew_rate rate;
-			enum ad5755_slew_step_size step_size;
-		} slew;
-	} dac[4];
-};
-
-#endif
diff --git a/include/linux/property.h b/include/linux/property.h
index 88fa726a76df..6670d5a1ec2a 100644
--- a/include/linux/property.h
+++ b/include/linux/property.h
@@ -122,6 +122,8 @@ void fwnode_handle_put(struct fwnode_handle *fwnode);
 
 int fwnode_irq_get(const struct fwnode_handle *fwnode, unsigned int index);
 
+void __iomem *fwnode_iomap(struct fwnode_handle *fwnode, int index);
+
 unsigned int device_get_child_node_count(struct device *dev);
 
 static inline bool device_property_read_bool(struct device *dev,