diff options
author | Danilo Krummrich <danilokrummrich@dk-develop.de> | 2022-02-15 14:39:12 -0800 |
---|---|---|
committer | Dmitry Torokhov <dmitry.torokhov@gmail.com> | 2022-02-15 17:25:36 -0800 |
commit | 2fa9c57af062ded71e68462264d315a547c72da2 (patch) | |
tree | 6ba8f84d9ff741fa814350f47b36016abaa75f9f /drivers | |
parent | 0dde5f82158b267c9f66879e6d0deb9c01d4964d (diff) | |
download | linux-2fa9c57af062ded71e68462264d315a547c72da2.tar.bz2 |
Input: ps2-gpio - use ktime for IRQ timekeeping
Using jiffies for the IRQ timekeeping is not sufficient for two reasons:
(1) Usually jiffies have a resolution of 1ms to 10ms. The IRQ intervals
based on the clock frequency of PS2 protocol specification (10kHz -
16.7kHz) are between ~60us and 100us only. Therefore only those IRQ
intervals can be detected which are either at the end of a transfer
or are overly delayed. While this is sufficient in most cases, since
we have quite a lot of ways to detect faulty transfers, it can
produce false positives in rare cases: When the jiffies value
changes right between two interrupt that are in time, we wrongly
assume that we missed one or more clock cycles.
(2) Some gpio controllers (e.g. the one in the bcm283x chips) may generate
spurious IRQs when processing interrupts in the frequency given by PS2
devices.
Both issues can be fixed by using ktime resolution for IRQ timekeeping.
However, it is still possible to miss clock cycles without detecting
them. When the PS2 device generates the falling edge of the clock signal
we have between ~30us and 50us to sample the data line, because after
this time we reach the next rising edge at which the device changes the
data signal already. But, the only thing we can detect is whether the
IRQ interval is within the given period. Therefore it is possible to
have an IRQ latency greater than ~30us to 50us, sample the wrong bit on
the data line and still be on time with the next IRQ. However, this can
only happen when within a given transfer the IRQ latency increases
slowly.
___ ______ ______ ______ ___
\ / \ / \ / \ /
\ / \ / \ / \ /
\______/ \______/ \______/ \______/
|-----------------| |--------|
60us/100us 30us/50us
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215160208.34826-3-danilokrummrich@dk-develop.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/input/serio/ps2-gpio.c | 102 |
1 files changed, 82 insertions, 20 deletions
diff --git a/drivers/input/serio/ps2-gpio.c b/drivers/input/serio/ps2-gpio.c index 1682125fba11..f1b7313a0866 100644 --- a/drivers/input/serio/ps2-gpio.c +++ b/drivers/input/serio/ps2-gpio.c @@ -19,6 +19,7 @@ #include <linux/of.h> #include <linux/jiffies.h> #include <linux/delay.h> +#include <linux/timekeeping.h> #define DRIVER_NAME "ps2-gpio" @@ -44,6 +45,30 @@ #define PS2_CMD_RESEND 0xfe +/* + * The PS2 protocol specifies a clock frequency between 10kHz and 16.7kHz, + * therefore the maximal interrupt interval should be 100us and the minimum + * interrupt interval should be ~60us. Let's allow +/- 20us for frequency + * deviations and interrupt latency. + * + * The data line must be samples after ~30us to 50us after the falling edge, + * since the device updates the data line at the rising edge. + * + * ___ ______ ______ ______ ___ + * \ / \ / \ / \ / + * \ / \ / \ / \ / + * \______/ \______/ \______/ \______/ + * + * |-----------------| |--------| + * 60us/100us 30us/50us + */ +#define PS2_CLK_FREQ_MIN_HZ 10000 +#define PS2_CLK_FREQ_MAX_HZ 16700 +#define PS2_CLK_MIN_INTERVAL_US ((1000 * 1000) / PS2_CLK_FREQ_MAX_HZ) +#define PS2_CLK_MAX_INTERVAL_US ((1000 * 1000) / PS2_CLK_FREQ_MIN_HZ) +#define PS2_IRQ_MIN_INTERVAL_US (PS2_CLK_MIN_INTERVAL_US - 20) +#define PS2_IRQ_MAX_INTERVAL_US (PS2_CLK_MAX_INTERVAL_US + 20) + struct ps2_gpio_data { struct device *dev; struct serio *serio; @@ -52,6 +77,8 @@ struct ps2_gpio_data { struct gpio_desc *gpio_data; bool write_enable; int irq; + ktime_t t_irq_now; + ktime_t t_irq_last; struct { unsigned char cnt; unsigned char byte; @@ -59,6 +86,8 @@ struct ps2_gpio_data { struct { unsigned char cnt; unsigned char byte; + ktime_t t_xfer_start; + ktime_t t_xfer_end; struct completion complete; struct mutex mutex; struct delayed_work work; @@ -69,6 +98,9 @@ static int ps2_gpio_open(struct serio *serio) { struct ps2_gpio_data *drvdata = serio->port_data; + drvdata->t_irq_last = 0; + drvdata->tx.t_xfer_end = 0; + enable_irq(drvdata->irq); return 0; } @@ -122,6 +154,7 @@ static void ps2_gpio_tx_work_fn(struct work_struct *work) struct ps2_gpio_data, tx.work); + drvdata->tx.t_xfer_start = ktime_get(); enable_irq(drvdata->irq); gpiod_direction_output(drvdata->gpio_data, 0); gpiod_direction_input(drvdata->gpio_clk); @@ -132,20 +165,31 @@ static irqreturn_t ps2_gpio_irq_rx(struct ps2_gpio_data *drvdata) unsigned char byte, cnt; int data; int rxflags = 0; - static unsigned long old_jiffies; + s64 us_delta; byte = drvdata->rx.byte; cnt = drvdata->rx.cnt; - if (old_jiffies == 0) - old_jiffies = jiffies; + drvdata->t_irq_now = ktime_get(); + + /* + * We need to consider spurious interrupts happening right after + * a TX xfer finished. + */ + us_delta = ktime_us_delta(drvdata->t_irq_now, drvdata->tx.t_xfer_end); + if (unlikely(us_delta < PS2_IRQ_MIN_INTERVAL_US)) + goto end; - if ((jiffies - old_jiffies) > usecs_to_jiffies(100)) { + us_delta = ktime_us_delta(drvdata->t_irq_now, drvdata->t_irq_last); + if (us_delta > PS2_IRQ_MAX_INTERVAL_US && cnt) { dev_err(drvdata->dev, "RX: timeout, probably we missed an interrupt\n"); goto err; + } else if (unlikely(us_delta < PS2_IRQ_MIN_INTERVAL_US)) { + /* Ignore spurious IRQs. */ + goto end; } - old_jiffies = jiffies; + drvdata->t_irq_last = drvdata->t_irq_now; data = gpiod_get_value(drvdata->gpio_data); if (unlikely(data < 0)) { @@ -183,7 +227,8 @@ static irqreturn_t ps2_gpio_irq_rx(struct ps2_gpio_data *drvdata) goto err; } - /* Do not send spurious ACK's and NACK's when write fn is + /* + * Do not send spurious ACK's and NACK's when write fn is * not provided. */ if (!drvdata->write_enable) { @@ -193,7 +238,8 @@ static irqreturn_t ps2_gpio_irq_rx(struct ps2_gpio_data *drvdata) break; } - /* Let's send the data without waiting for the stop bit to be + /* + * Let's send the data without waiting for the stop bit to be * sent. It may happen that we miss the stop bit. When this * happens we have no way to recover from this, certainly * missing the parity bit would be recognized when processing @@ -209,7 +255,7 @@ static irqreturn_t ps2_gpio_irq_rx(struct ps2_gpio_data *drvdata) goto err; } cnt = byte = 0; - old_jiffies = 0; + goto end; /* success */ default: dev_err(drvdata->dev, "RX: got out of sync with the device\n"); @@ -221,7 +267,6 @@ static irqreturn_t ps2_gpio_irq_rx(struct ps2_gpio_data *drvdata) err: cnt = byte = 0; - old_jiffies = 0; __ps2_gpio_write(drvdata->serio, PS2_CMD_RESEND); end: drvdata->rx.cnt = cnt; @@ -233,20 +278,34 @@ static irqreturn_t ps2_gpio_irq_tx(struct ps2_gpio_data *drvdata) { unsigned char byte, cnt; int data; - static unsigned long old_jiffies; + s64 us_delta; cnt = drvdata->tx.cnt; byte = drvdata->tx.byte; - if (old_jiffies == 0) - old_jiffies = jiffies; + drvdata->t_irq_now = ktime_get(); + + /* + * There might be pending IRQs since we disabled IRQs in + * __ps2_gpio_write(). We can expect at least one clock period until + * the device generates the first falling edge after releasing the + * clock line. + */ + us_delta = ktime_us_delta(drvdata->t_irq_now, + drvdata->tx.t_xfer_start); + if (unlikely(us_delta < PS2_CLK_MIN_INTERVAL_US)) + goto end; - if ((jiffies - old_jiffies) > usecs_to_jiffies(100)) { + us_delta = ktime_us_delta(drvdata->t_irq_now, drvdata->t_irq_last); + if (us_delta > PS2_IRQ_MAX_INTERVAL_US && cnt > 1) { dev_err(drvdata->dev, "TX: timeout, probably we missed an interrupt\n"); goto err; + } else if (unlikely(us_delta < PS2_IRQ_MIN_INTERVAL_US)) { + /* Ignore spurious IRQs. */ + goto end; } - old_jiffies = jiffies; + drvdata->t_irq_last = drvdata->t_irq_now; switch (cnt) { case PS2_START_BIT: @@ -275,7 +334,8 @@ static irqreturn_t ps2_gpio_irq_tx(struct ps2_gpio_data *drvdata) gpiod_direction_input(drvdata->gpio_data); break; case PS2_TX_TIMEOUT: - /* Devices generate one extra clock pulse before sending the + /* + * Devices generate one extra clock pulse before sending the * acknowledgment. */ break; @@ -287,14 +347,15 @@ static irqreturn_t ps2_gpio_irq_tx(struct ps2_gpio_data *drvdata) goto err; } + drvdata->tx.t_xfer_end = ktime_get(); drvdata->mode = PS2_MODE_RX; complete(&drvdata->tx.complete); cnt = 1; - old_jiffies = 0; goto end; /* success */ default: - /* Probably we missed the stop bit. Therefore we release data + /* + * Probably we missed the stop bit. Therefore we release data * line and try again. */ gpiod_direction_input(drvdata->gpio_data); @@ -307,7 +368,6 @@ static irqreturn_t ps2_gpio_irq_tx(struct ps2_gpio_data *drvdata) err: cnt = 1; - old_jiffies = 0; gpiod_direction_input(drvdata->gpio_data); __ps2_gpio_write(drvdata->serio, drvdata->tx.byte); end: @@ -391,7 +451,8 @@ static int ps2_gpio_probe(struct platform_device *pdev) serio->id.type = SERIO_8042; serio->open = ps2_gpio_open; serio->close = ps2_gpio_close; - /* Write can be enabled in platform/dt data, but possibly it will not + /* + * Write can be enabled in platform/dt data, but possibly it will not * work because of the tough timings. */ serio->write = drvdata->write_enable ? ps2_gpio_write : NULL; @@ -404,7 +465,8 @@ static int ps2_gpio_probe(struct platform_device *pdev) drvdata->dev = dev; drvdata->mode = PS2_MODE_RX; - /* Tx count always starts at 1, as the start bit is sent implicitly by + /* + * Tx count always starts at 1, as the start bit is sent implicitly by * host-to-device communication initialization. */ drvdata->tx.cnt = 1; |