Merge remote-tracking branch 'torvalds/master' into perf/core

To update the perf/core codebase.

Fix conflict by moving arch__post_evsel_config(evsel, attr) to the end
of evsel__config(), after what was added in:

  49c692b7dfc9b6c0 ("perf offcpu: Accept allowed sample types only")

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

9 files changed, 62 insertions, 40 deletions

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index cfbd2de0ca6e..3f56dbc9432b 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -23,6 +23,7 @@
 #include <linux/sysrq.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/tty.h>
 #include <linux/ratelimit.h>
 #include <linux/tty_flip.h>
@@ -559,6 +560,9 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
 
 		up->port.dev = dev;
 
+		if (uart_console_enabled(&up->port))
+			pm_runtime_get_sync(up->port.dev);
+
 		serial8250_apply_quirks(up);
 		uart_add_one_port(drv, &up->port);
 	}
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index 7133fceed35e..a8dba4a0a8fb 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -106,10 +106,10 @@ int serial8250_tx_dma(struct uart_8250_port *p)
 				   UART_XMIT_SIZE, DMA_TO_DEVICE);
 
 	dma_async_issue_pending(dma->txchan);
-	if (dma->tx_err) {
+	serial8250_clear_THRI(p);
+	if (dma->tx_err)
 		dma->tx_err = 0;
-		serial8250_clear_THRI(p);
-	}
+
 	return 0;
 err:
 	dma->tx_err = 1;
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index f57bbd32ef11..bb6aca07ab56 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -47,7 +47,7 @@
 #define RZN1_UART_xDMACR_DMA_EN		BIT(0)
 #define RZN1_UART_xDMACR_1_WORD_BURST	(0 << 1)
 #define RZN1_UART_xDMACR_4_WORD_BURST	(1 << 1)
-#define RZN1_UART_xDMACR_8_WORD_BURST	(3 << 1)
+#define RZN1_UART_xDMACR_8_WORD_BURST	(2 << 1)
 #define RZN1_UART_xDMACR_BLK_SZ(x)	((x) << 3)
 
 /* Quirks */
@@ -773,18 +773,18 @@ static const struct of_device_id dw8250_of_match[] = {
 MODULE_DEVICE_TABLE(of, dw8250_of_match);
 
 static const struct acpi_device_id dw8250_acpi_match[] = {
-	{ "INT33C4", 0 },
-	{ "INT33C5", 0 },
-	{ "INT3434", 0 },
-	{ "INT3435", 0 },
-	{ "80860F0A", 0 },
-	{ "8086228A", 0 },
-	{ "APMC0D08", 0},
-	{ "AMD0020", 0 },
-	{ "AMDI0020", 0 },
-	{ "AMDI0022", 0 },
-	{ "BRCM2032", 0 },
-	{ "HISI0031", 0 },
+	{ "80860F0A", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "8086228A", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "AMD0020", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "AMDI0020", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "AMDI0022", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "APMC0D08", (kernel_ulong_t)&dw8250_dw_apb},
+	{ "BRCM2032", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "HISI0031", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INT33C4", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INT33C5", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INT3434", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INT3435", (kernel_ulong_t)&dw8250_dw_apb },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 8f32fe9e149e..3c36a06a20b0 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1949,7 +1949,7 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
 	if ((status & UART_LSR_THRE) && (up->ier & UART_IER_THRI)) {
 		if (!up->dma || up->dma->tx_err)
 			serial8250_tx_chars(up);
-		else
+		else if (!up->dma->tx_running)
 			__stop_tx(up);
 	}
 
@@ -2975,8 +2975,10 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
 	case UPIO_MEM32BE:
 	case UPIO_MEM16:
 	case UPIO_MEM:
-		if (!port->mapbase)
+		if (!port->mapbase) {
+			ret = -EINVAL;
 			break;
+		}
 
 		if (!request_mem_region(port->mapbase, size, "serial")) {
 			ret = -EBUSY;
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 97ef41cb2721..16a21422ddce 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1367,6 +1367,15 @@ static void pl011_stop_rx(struct uart_port *port)
 	pl011_dma_rx_stop(uap);
 }
 
+static void pl011_throttle_rx(struct uart_port *port)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	pl011_stop_rx(port);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
 static void pl011_enable_ms(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
@@ -1788,9 +1797,10 @@ static int pl011_allocate_irq(struct uart_amba_port *uap)
  */
 static void pl011_enable_interrupts(struct uart_amba_port *uap)
 {
+	unsigned long flags;
 	unsigned int i;
 
-	spin_lock_irq(&uap->port.lock);
+	spin_lock_irqsave(&uap->port.lock, flags);
 
 	/* Clear out any spuriously appearing RX interrupts */
 	pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR);
@@ -1812,7 +1822,14 @@ static void pl011_enable_interrupts(struct uart_amba_port *uap)
 	if (!pl011_dma_rx_running(uap))
 		uap->im |= UART011_RXIM;
 	pl011_write(uap->im, uap, REG_IMSC);
-	spin_unlock_irq(&uap->port.lock);
+	spin_unlock_irqrestore(&uap->port.lock, flags);
+}
+
+static void pl011_unthrottle_rx(struct uart_port *port)
+{
+	struct uart_amba_port *uap = container_of(port, struct uart_amba_port, port);
+
+	pl011_enable_interrupts(uap);
 }
 
 static int pl011_startup(struct uart_port *port)
@@ -2225,6 +2242,8 @@ static const struct uart_ops amba_pl011_pops = {
 	.stop_tx	= pl011_stop_tx,
 	.start_tx	= pl011_start_tx,
 	.stop_rx	= pl011_stop_rx,
+	.throttle	= pl011_throttle_rx,
+	.unthrottle	= pl011_unthrottle_rx,
 	.enable_ms	= pl011_enable_ms,
 	.break_ctl	= pl011_break_ctl,
 	.startup	= pl011_startup,
diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
index 0429c2a54290..93489fe334d0 100644
--- a/drivers/tty/serial/mvebu-uart.c
+++ b/drivers/tty/serial/mvebu-uart.c
@@ -470,14 +470,14 @@ static void mvebu_uart_shutdown(struct uart_port *port)
 	}
 }
 
-static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
+static unsigned int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
 {
 	unsigned int d_divisor, m_divisor;
 	unsigned long flags;
 	u32 brdv, osamp;
 
 	if (!port->uartclk)
-		return -EOPNOTSUPP;
+		return 0;
 
 	/*
 	 * The baudrate is derived from the UART clock thanks to divisors:
@@ -548,7 +548,7 @@ static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
 			(m_divisor << 16) | (m_divisor << 24);
 	writel(osamp, port->membase + UART_OSAMP);
 
-	return 0;
+	return DIV_ROUND_CLOSEST(port->uartclk, d_divisor * m_divisor);
 }
 
 static void mvebu_uart_set_termios(struct uart_port *port,
@@ -587,15 +587,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
 	max_baud = port->uartclk / 80;
 
 	baud = uart_get_baud_rate(port, termios, old, min_baud, max_baud);
-	if (mvebu_uart_baud_rate_set(port, baud)) {
-		/* No clock available, baudrate cannot be changed */
-		if (old)
-			baud = uart_get_baud_rate(port, old, NULL,
-						  min_baud, max_baud);
-	} else {
-		tty_termios_encode_baud_rate(termios, baud, baud);
-		uart_update_timeout(port, termios->c_cflag, baud);
-	}
+	baud = mvebu_uart_baud_rate_set(port, baud);
+
+	/* In case baudrate cannot be changed, report previous old value */
+	if (baud == 0 && old)
+		baud = tty_termios_baud_rate(old);
 
 	/* Only the following flag changes are supported */
 	if (old) {
@@ -606,6 +602,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
 		termios->c_cflag |= CS8;
 	}
 
+	if (baud != 0) {
+		tty_termios_encode_baud_rate(termios, baud, baud);
+		uart_update_timeout(port, termios->c_cflag, baud);
+	}
+
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c
index d5ca904def34..1afe47b62ad5 100644
--- a/drivers/tty/serial/samsung_tty.c
+++ b/drivers/tty/serial/samsung_tty.c
@@ -377,8 +377,7 @@ static void enable_tx_dma(struct s3c24xx_uart_port *ourport)
 	/* Enable tx dma mode */
 	ucon = rd_regl(port, S3C2410_UCON);
 	ucon &= ~(S3C64XX_UCON_TXBURST_MASK | S3C64XX_UCON_TXMODE_MASK);
-	ucon |= (dma_get_cache_alignment() >= 16) ?
-		S3C64XX_UCON_TXBURST_16 : S3C64XX_UCON_TXBURST_1;
+	ucon |= S3C64XX_UCON_TXBURST_1;
 	ucon |= S3C64XX_UCON_TXMODE_DMA;
 	wr_regl(port,  S3C2410_UCON, ucon);
 
@@ -674,7 +673,7 @@ static void enable_rx_dma(struct s3c24xx_uart_port *ourport)
 			S3C64XX_UCON_DMASUS_EN |
 			S3C64XX_UCON_TIMEOUT_EN |
 			S3C64XX_UCON_RXMODE_MASK);
-	ucon |= S3C64XX_UCON_RXBURST_16 |
+	ucon |= S3C64XX_UCON_RXBURST_1 |
 			0xf << S3C64XX_UCON_TIMEOUT_SHIFT |
 			S3C64XX_UCON_EMPTYINT_EN |
 			S3C64XX_UCON_TIMEOUT_EN |
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 338ebadfd44b..3dc926d6c00a 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1941,11 +1941,6 @@ static int uart_proc_show(struct seq_file *m, void *v)
 }
 #endif
 
-static inline bool uart_console_enabled(struct uart_port *port)
-{
-	return uart_console(port) && (port->cons->flags & CON_ENABLED);
-}
-
 static void uart_port_spin_lock_init(struct uart_port *port)
 {
 	spin_lock_init(&port->lock);
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index b7b44f4050d4..0973b03eeeaa 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -72,6 +72,8 @@ static void stm32_usart_config_reg_rs485(u32 *cr1, u32 *cr3, u32 delay_ADE,
 	*cr3 |= USART_CR3_DEM;
 	over8 = *cr1 & USART_CR1_OVER8;
 
+	*cr1 &= ~(USART_CR1_DEDT_MASK | USART_CR1_DEAT_MASK);
+
 	if (over8)
 		rs485_deat_dedt = delay_ADE * baud * 8;
 	else