Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Consolidate duplicated 'next function' scanning and extend to allow
     'isolated functions' on s390, similar to existing hypervisors
     (Niklas Schnelle)

  Resource management:
   - Implement pci_iobar_pfn() for sparc, which allows us to remove the
     sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().

     This removes the ability to map the entire PCI I/O space using
     /proc/bus/pci, but we believe that's already been broken since
     v2.6.28 (Arnd Bergmann)

   - Move common PCI definitions to asm-generic/pci.h and rework others
     to be be more specific and more encapsulated in arches that need
     them (Stafford Horne)

  Power management:

   - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
     CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)

  Virtualization:

   - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
     the functions but don't advertise an ACS capability (Pavan Chebbi)

  Error handling:

   - Clear PCI Status register during enumeration in case firmware left
     errors logged (Kai-Heng Feng)

   - When we have native control of AER, enable error reporting for all
     devices that support AER. Previously only a few drivers enabled
     this (Stefan Roese)

   - Keep AER error reporting enabled for switches. Previously we
     enabled this during enumeration but immediately disabled it (Stefan
     Roese)

   - Iterate over error counters instead of error strings to avoid
     printing junk in AER sysfs counters (Mohamed Khalfella)

  ASPM:

   - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
     via sysfs, are not lost across power state changes (Kai-Heng Feng)

  Endpoint framework:

   - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)

  Endpoint embedded DMA controller driver:

   - Simplify and clean up support for the DesignWare embedded DMA
     (eDMA) controller (Frank Li, Serge Semin)

  Broadcom STB PCIe controller driver:

   - Avoid config space accesses when link is down because we can't
     recover from the CPU aborts these cause (Jim Quinlan)

   - Look for power regulators described under Root Ports in DT and
     enable them before scanning the secondary bus (Jim Quinlan)

   - Disable/enable regulators in suspend/resume (Jim Quinlan)

  Freescale i.MX6 PCIe controller driver:

   - Simplify and clean up clock and PHY management (Richard Zhu)

   - Disable/enable regulators in suspend/resume (Richard Zhu)

   - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)

   - Allow speeds faster than Gen2 (Richard Zhu)

   - Make link being down a non-fatal error so controller probe doesn't
     fail if there are no Endpoints connected (Richard Zhu)

  Loongson PCIe controller driver:

   - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)

   - Avoid config reads to non-existent LS2K/LS7A devices because a
     hardware defect causes machine hangs (Huacai Chen)

   - Work around LS7A integrated devices that report incorrect Interrupt
     Pin values (Jianmin Lv)

  Marvell Aardvark PCIe controller driver:

   - Add support for AER and Slot capability on emulated bridge (Pali
     Rohár)

  MediaTek PCIe controller driver:

   - Add Airoha EN7532 to DT binding (John Crispin)

   - Allow building of driver for ARCH_AIROHA (Felix Fietkau)

  MediaTek PCIe Gen3 controller driver:

   - Print decoded LTSSM state when the link doesn't come up (Jianjun
     Wang)

  NVIDIA Tegra194 PCIe controller driver:

   - Convert DT binding to json-schema (Vidya Sagar)

   - Add DT bindings and driver support for Tegra234 Root Port and
     Endpoint mode (Vidya Sagar)

   - Fix some Root Port interrupt handling issues (Vidya Sagar)

   - Set default Max Payload Size to 256 bytes (Vidya Sagar)

   - Fix Data Link Feature capability programming (Vidya Sagar)

   - Extend Endpoint mode support to devices beyond Controller-5 (Vidya
     Sagar)

  Qualcomm PCIe controller driver:

   - Rework clock, reset, PHY power-on ordering to avoid hangs and
     improve consistency (Robert Marko, Christian Marangi)

   - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)

   - Add IPQ60xx support (Selvam Sathappan Periakaruppan)

   - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)

   - Add support for more than 32 MSI interrupts (Dmitry Baryshkov)

  Renesas R-Car PCIe controller driver:

   - Convert DT binding to json-schema (Herve Codina)

   - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
     (Herve Codina)

  Samsung Exynos PCIe controller driver:

   - Fix phy-exynos-pcie driver so it follows the 'phy_init() before
     phy_power_on()' PHY programming model (Marek Szyprowski)

  Synopsys DesignWare PCIe controller driver:

   - Simplify and clean up the DWC core extensively (Serge Semin)

   - Fix an issue with programming the ATU for regions that cross a 4GB
     boundary (Serge Semin)

   - Enable the CDM check if 'snps,enable-cdm-check' exists; previously
     we skipped it if 'num-lanes' was absent (Serge Semin)

   - Allocate a 32-bit DMA-able page to be MSI target instead of using a
     driver data structure that may not be addressable with 32-bit
     address (Will McVicker)

   - Add DWC core support for more than 32 MSI interrupts (Dmitry
     Baryshkov)

  Xilinx Versal CPM PCIe controller driver:

   - Add DT binding and driver support for Versal CPM5 Gen5 Root Port
     (Bharat Kumar Gogada)"

* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
  PCI: imx6: Support more than Gen2 speed link mode
  PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
  PCI: imx6: Reformat suspend callback to keep symmetric with resume
  PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
  PCI: imx6: Disable clocks in reverse order of enable
  PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
  PCI: imx6: Reduce resume time by only starting link if it was up before suspend
  PCI: imx6: Mark the link down as non-fatal error
  PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
  PCI: imx6: Turn off regulator when system is in suspend mode
  PCI: imx6: Call host init function directly in resume
  PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
  PCI: imx6: Propagate .host_init() errors to caller
  PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
  PCI: imx6: Factor out ref clock disable to match enable
  PCI: imx6: Move imx6_pcie_clk_disable() earlier
  PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
  PCI: imx6: Move PHY management functions together
  PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
  PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
  ...

1 files changed, 44 insertions, 46 deletions

diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 17a969942d37..9884d8b29d3b 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -1890,6 +1890,9 @@ int pci_setup_device(struct pci_dev *dev)
 
 	dev->broken_intx_masking = pci_intx_mask_broken(dev);
 
+	/* Clear errors left from system firmware */
+	pci_write_config_word(dev, PCI_STATUS, 0xffff);
+
 	switch (dev->hdr_type) {		    /* header type */
 	case PCI_HEADER_TYPE_NORMAL:		    /* standard header */
 		if (class == PCI_CLASS_BRIDGE_PCI)
@@ -2579,33 +2582,39 @@ struct pci_dev *pci_scan_single_device(struct pci_bus *bus, int devfn)
 }
 EXPORT_SYMBOL(pci_scan_single_device);
 
-static unsigned int next_fn(struct pci_bus *bus, struct pci_dev *dev,
-			    unsigned int fn)
+static int next_ari_fn(struct pci_bus *bus, struct pci_dev *dev, int fn)
 {
 	int pos;
 	u16 cap = 0;
 	unsigned int next_fn;
 
-	if (pci_ari_enabled(bus)) {
-		if (!dev)
-			return 0;
-		pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ARI);
-		if (!pos)
-			return 0;
+	if (!dev)
+		return -ENODEV;
 
-		pci_read_config_word(dev, pos + PCI_ARI_CAP, &cap);
-		next_fn = PCI_ARI_CAP_NFN(cap);
-		if (next_fn <= fn)
-			return 0;	/* protect against malformed list */
+	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ARI);
+	if (!pos)
+		return -ENODEV;
 
-		return next_fn;
-	}
+	pci_read_config_word(dev, pos + PCI_ARI_CAP, &cap);
+	next_fn = PCI_ARI_CAP_NFN(cap);
+	if (next_fn <= fn)
+		return -ENODEV;	/* protect against malformed list */
 
-	/* dev may be NULL for non-contiguous multifunction devices */
-	if (!dev || dev->multifunction)
-		return (fn + 1) % 8;
+	return next_fn;
+}
 
-	return 0;
+static int next_fn(struct pci_bus *bus, struct pci_dev *dev, int fn)
+{
+	if (pci_ari_enabled(bus))
+		return next_ari_fn(bus, dev, fn);
+
+	if (fn >= 7)
+		return -ENODEV;
+	/* only multifunction devices may have more functions */
+	if (dev && !dev->multifunction)
+		return -ENODEV;
+
+	return fn + 1;
 }
 
 static int only_one_child(struct pci_bus *bus)
@@ -2643,26 +2652,30 @@ static int only_one_child(struct pci_bus *bus)
  */
 int pci_scan_slot(struct pci_bus *bus, int devfn)
 {
-	unsigned int fn, nr = 0;
 	struct pci_dev *dev;
+	int fn = 0, nr = 0;
 
 	if (only_one_child(bus) && (devfn > 0))
 		return 0; /* Already scanned the entire slot */
 
-	dev = pci_scan_single_device(bus, devfn);
-	if (!dev)
-		return 0;
-	if (!pci_dev_is_added(dev))
-		nr++;
-
-	for (fn = next_fn(bus, dev, 0); fn > 0; fn = next_fn(bus, dev, fn)) {
+	do {
 		dev = pci_scan_single_device(bus, devfn + fn);
 		if (dev) {
 			if (!pci_dev_is_added(dev))
 				nr++;
-			dev->multifunction = 1;
+			if (fn > 0)
+				dev->multifunction = 1;
+		} else if (fn == 0) {
+			/*
+			 * Function 0 is required unless we are running on
+			 * a hypervisor that passes through individual PCI
+			 * functions.
+			 */
+			if (!hypervisor_isolated_pci_functions())
+				break;
 		}
-	}
+		fn = next_fn(bus, dev, fn);
+	} while (fn >= 0);
 
 	/* Only one slot has PCIe device */
 	if (bus->self && nr)
@@ -2858,29 +2871,14 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
 {
 	unsigned int used_buses, normal_bridges = 0, hotplug_bridges = 0;
 	unsigned int start = bus->busn_res.start;
-	unsigned int devfn, fn, cmax, max = start;
+	unsigned int devfn, cmax, max = start;
 	struct pci_dev *dev;
-	int nr_devs;
 
 	dev_dbg(&bus->dev, "scanning bus\n");
 
 	/* Go find them, Rover! */
-	for (devfn = 0; devfn < 256; devfn += 8) {
-		nr_devs = pci_scan_slot(bus, devfn);
-
-		/*
-		 * The Jailhouse hypervisor may pass individual functions of a
-		 * multi-function device to a guest without passing function 0.
-		 * Look for them as well.
-		 */
-		if (jailhouse_paravirt() && nr_devs == 0) {
-			for (fn = 1; fn < 8; fn++) {
-				dev = pci_scan_single_device(bus, devfn + fn);
-				if (dev)
-					dev->multifunction = 1;
-			}
-		}
-	}
+	for (devfn = 0; devfn < 256; devfn += 8)
+		pci_scan_slot(bus, devfn);
 
 	/* Reserve buses for SR-IOV capability */
 	used_buses = pci_iov_bus_range(bus);