Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

Changes of note:

 1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.

 2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
    David Ahern.

 3) Allow the user to ask for the statistics to be filtered out of
    ipv4/ipv6 address netlink dumps.  From Sowmini Varadhan.

 4) More work to pass the network namespace context around deep into
    various packet path APIs, starting with the netfilter hooks.  From
    Eric W Biederman.

 5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
    Richter.

 6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.

 7) Support Very High Throughput in wireless MESH code, from Bob
    Copeland.

 8) Allow setting the ageing_time in switchdev/rocker.  From Scott
    Feldman.

 9) Properly autoload L2TP type modules, from Stephen Hemminger.

10) Fix and enable offload features by default in 8139cp driver, from
    David Woodhouse.

11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
    Jiri Benc.

12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
    Opstad.

13) Fix IPSEC flowcache overflows on large systems, from Steffen
    Klassert.

14) Convert bridging to track VLANs using rhashtable entries rather than
    a bitmap.  From Nikolay Aleksandrov.

15) Make TCP listener handling completely lockless, this is a major
    accomplishment.  Incoming request sockets now live in the
    established hash table just like any other socket too.

    From Eric Dumazet.

15) Provide more bridging attributes to netlink, from Nikolay
    Aleksandrov.

16) Use hash based algorithm for ipv4 multipath routing, this was very
    long overdue.  From Peter Nørlund.

17) Several y2038 cures, mostly avoiding timespec.  From Arnd Bergmann.

18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.

19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet.  This
    influences the port binding selection logic used by SO_REUSEPORT.

20) Add ipv6 support to VRF, from David Ahern.

21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.

22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.

23) Implement RACK loss recovery in TCP, from Yuchung Cheng.

24) Support multipath routes in MPLS, from Roopa Prabhu.

25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
    Dumazet.

26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
    Sudarsana Kalluru.

27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
    Sowa.

28) Support ipv6 geneve tunnels, from John W Linville.

29) Add flood control support to switchdev layer, from Ido Schimmel.

30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
    Hannes Frederic Sowa.

31) Support persistent maps and progs in bpf, from Daniel Borkmann.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
  sh_eth: use DMA barriers
  switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
  net: sched: kill dead code in sch_choke.c
  irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
  net: dsa: mv88e6xxx: include DSA ports in VLANs
  net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
  net/core: fix for_each_netdev_feature
  vlan: Invoke driver vlan hooks only if device is present
  arcnet/com20020: add LEDS_CLASS dependency
  bpf, verifier: annotate verbose printer with __printf
  dp83640: Only wait for timestamps for packets with timestamping enabled.
  ptp: Change ptp_class to a proper bitmask
  dp83640: Prune rx timestamp list before reading from it
  dp83640: Delay scheduled work.
  dp83640: Include hash in timestamp/packet matching
  ipv6: fix tunnel error handling
  net/mlx5e: Fix LSO vlan insertion
  net/mlx5e: Re-eanble client vlan TX acceleration
  net/mlx5e: Return error in case mlx5e_set_features() fails
  net/mlx5e: Don't allow more than max supported channels
  ...

1 files changed, 138 insertions, 155 deletions

diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index 7e91d825c760..47e9a90d6b10 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -140,65 +140,6 @@ static inline u32 i40e_get_head(struct i40e_ring *tx_ring)
 	return le32_to_cpu(*(volatile __le32 *)head);
 }
 
-/**
- * i40e_get_tx_pending - how many tx descriptors not processed
- * @tx_ring: the ring of descriptors
- *
- * Since there is no access to the ring head register
- * in XL710, we need to use our local copies
- **/
-static u32 i40e_get_tx_pending(struct i40e_ring *ring)
-{
-	u32 head, tail;
-
-	head = i40e_get_head(ring);
-	tail = readl(ring->tail);
-
-	if (head != tail)
-		return (head < tail) ?
-			tail - head : (tail + ring->count - head);
-
-	return 0;
-}
-
-/**
- * i40e_check_tx_hang - Is there a hang in the Tx queue
- * @tx_ring: the ring of descriptors
- **/
-static bool i40e_check_tx_hang(struct i40e_ring *tx_ring)
-{
-	u32 tx_done = tx_ring->stats.packets;
-	u32 tx_done_old = tx_ring->tx_stats.tx_done_old;
-	u32 tx_pending = i40e_get_tx_pending(tx_ring);
-	bool ret = false;
-
-	clear_check_for_tx_hang(tx_ring);
-
-	/* Check for a hung queue, but be thorough. This verifies
-	 * that a transmit has been completed since the previous
-	 * check AND there is at least one packet pending. The
-	 * ARMED bit is set to indicate a potential hang. The
-	 * bit is cleared if a pause frame is received to remove
-	 * false hang detection due to PFC or 802.3x frames. By
-	 * requiring this to fail twice we avoid races with
-	 * PFC clearing the ARMED bit and conditions where we
-	 * run the check_tx_hang logic with a transmit completion
-	 * pending but without time to complete it yet.
-	 */
-	if ((tx_done_old == tx_done) && tx_pending) {
-		/* make sure it is true for two checks in a row */
-		ret = test_and_set_bit(__I40E_HANG_CHECK_ARMED,
-				       &tx_ring->state);
-	} else if (tx_done_old == tx_done &&
-		   (tx_pending < I40E_MIN_DESC_PENDING) && (tx_pending > 0)) {
-		/* update completed stats and disarm the hang check */
-		tx_ring->tx_stats.tx_done_old = tx_done;
-		clear_bit(__I40E_HANG_CHECK_ARMED, &tx_ring->state);
-	}
-
-	return ret;
-}
-
 #define WB_STRIDE 0x3
 
 /**
@@ -304,36 +245,15 @@ static bool i40e_clean_tx_irq(struct i40e_ring *tx_ring, int budget)
 	tx_ring->q_vector->tx.total_bytes += total_bytes;
 	tx_ring->q_vector->tx.total_packets += total_packets;
 
+	/* check to see if there are any non-cache aligned descriptors
+	 * waiting to be written back, and kick the hardware to force
+	 * them to be written back in case of napi polling
+	 */
 	if (budget &&
 	    !((i & WB_STRIDE) == WB_STRIDE) &&
 	    !test_bit(__I40E_DOWN, &tx_ring->vsi->state) &&
 	    (I40E_DESC_UNUSED(tx_ring) != tx_ring->count))
 		tx_ring->arm_wb = true;
-	else
-		tx_ring->arm_wb = false;
-
-	if (check_for_tx_hang(tx_ring) && i40e_check_tx_hang(tx_ring)) {
-		/* schedule immediate reset if we believe we hung */
-		dev_info(tx_ring->dev, "Detected Tx Unit Hang\n"
-			 "  VSI                  <%d>\n"
-			 "  Tx Queue             <%d>\n"
-			 "  next_to_use          <%x>\n"
-			 "  next_to_clean        <%x>\n",
-			 tx_ring->vsi->seid,
-			 tx_ring->queue_index,
-			 tx_ring->next_to_use, i);
-
-		netif_stop_subqueue(tx_ring->netdev, tx_ring->queue_index);
-
-		dev_info(tx_ring->dev,
-			 "tx hang detected on queue %d, resetting adapter\n",
-			 tx_ring->queue_index);
-
-		tx_ring->netdev->netdev_ops->ndo_tx_timeout(tx_ring->netdev);
-
-		/* the adapter is about to reset, no point in enabling stuff */
-		return true;
-	}
 
 	netdev_tx_completed_queue(netdev_get_tx_queue(tx_ring->netdev,
 						      tx_ring->queue_index),
@@ -355,16 +275,16 @@ static bool i40e_clean_tx_irq(struct i40e_ring *tx_ring, int budget)
 		}
 	}
 
-	return budget > 0;
+	return !!budget;
 }
 
 /**
- * i40e_force_wb -Arm hardware to do a wb on noncache aligned descriptors
+ * i40evf_force_wb -Arm hardware to do a wb on noncache aligned descriptors
  * @vsi: the VSI we care about
  * @q_vector: the vector  on which to force writeback
  *
  **/
-static void i40e_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
+static void i40evf_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
 {
 	u16 flags = q_vector->tx.ring[0].flags;
 
@@ -398,6 +318,8 @@ static void i40e_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
  * i40e_set_new_dynamic_itr - Find new ITR level
  * @rc: structure containing ring performance data
  *
+ * Returns true if ITR changed, false if not
+ *
  * Stores a new ITR value based on packets and byte counts during
  * the last interrupt.  The advantage of per interrupt computation
  * is faster updates and more accurate ITR for the current traffic
@@ -406,21 +328,32 @@ static void i40e_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
  * testing data as well as attempting to minimize response time
  * while increasing bulk throughput.
  **/
-static void i40e_set_new_dynamic_itr(struct i40e_ring_container *rc)
+static bool i40e_set_new_dynamic_itr(struct i40e_ring_container *rc)
 {
 	enum i40e_latency_range new_latency_range = rc->latency_range;
+	struct i40e_q_vector *qv = rc->ring->q_vector;
 	u32 new_itr = rc->itr;
 	int bytes_per_int;
+	int usecs;
 
 	if (rc->total_packets == 0 || !rc->itr)
-		return;
+		return false;
 
 	/* simple throttlerate management
-	 *   0-10MB/s   lowest (100000 ints/s)
+	 *   0-10MB/s   lowest (50000 ints/s)
 	 *  10-20MB/s   low    (20000 ints/s)
-	 *  20-1249MB/s bulk   (8000 ints/s)
+	 *  20-1249MB/s bulk   (18000 ints/s)
+	 *  > 40000 Rx packets per second (8000 ints/s)
+	 *
+	 * The math works out because the divisor is in 10^(-6) which
+	 * turns the bytes/us input value into MB/s values, but
+	 * make sure to use usecs, as the register values written
+	 * are in 2 usec increments in the ITR registers, and make sure
+	 * to use the smoothed values that the countdown timer gives us.
 	 */
-	bytes_per_int = rc->total_bytes / rc->itr;
+	usecs = (rc->itr << 1) * ITR_COUNTDOWN_START;
+	bytes_per_int = rc->total_bytes / usecs;
+
 	switch (new_latency_range) {
 	case I40E_LOWEST_LATENCY:
 		if (bytes_per_int > 10)
@@ -433,35 +366,52 @@ static void i40e_set_new_dynamic_itr(struct i40e_ring_container *rc)
 			new_latency_range = I40E_LOWEST_LATENCY;
 		break;
 	case I40E_BULK_LATENCY:
-		if (bytes_per_int <= 20)
-			new_latency_range = I40E_LOW_LATENCY;
-		break;
+	case I40E_ULTRA_LATENCY:
 	default:
 		if (bytes_per_int <= 20)
 			new_latency_range = I40E_LOW_LATENCY;
 		break;
 	}
+
+	/* this is to adjust RX more aggressively when streaming small
+	 * packets.  The value of 40000 was picked as it is just beyond
+	 * what the hardware can receive per second if in low latency
+	 * mode.
+	 */
+#define RX_ULTRA_PACKET_RATE 40000
+
+	if ((((rc->total_packets * 1000000) / usecs) > RX_ULTRA_PACKET_RATE) &&
+	    (&qv->rx == rc))
+		new_latency_range = I40E_ULTRA_LATENCY;
+
 	rc->latency_range = new_latency_range;
 
 	switch (new_latency_range) {
 	case I40E_LOWEST_LATENCY:
-		new_itr = I40E_ITR_100K;
+		new_itr = I40E_ITR_50K;
 		break;
 	case I40E_LOW_LATENCY:
 		new_itr = I40E_ITR_20K;
 		break;
 	case I40E_BULK_LATENCY:
+		new_itr = I40E_ITR_18K;
+		break;
+	case I40E_ULTRA_LATENCY:
 		new_itr = I40E_ITR_8K;
 		break;
 	default:
 		break;
 	}
 
-	if (new_itr != rc->itr)
-		rc->itr = new_itr;
-
 	rc->total_bytes = 0;
 	rc->total_packets = 0;
+
+	if (new_itr != rc->itr) {
+		rc->itr = new_itr;
+		return true;
+	}
+
+	return false;
 }
 
 /*
@@ -822,16 +772,11 @@ static void i40e_receive_skb(struct i40e_ring *rx_ring,
 			     struct sk_buff *skb, u16 vlan_tag)
 {
 	struct i40e_q_vector *q_vector = rx_ring->q_vector;
-	struct i40e_vsi *vsi = rx_ring->vsi;
-	u64 flags = vsi->back->flags;
 
 	if (vlan_tag & VLAN_VID_MASK)
 		__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
 
-	if (flags & I40E_FLAG_IN_NETPOLL)
-		netif_rx(skb);
-	else
-		napi_gro_receive(&q_vector->napi, skb);
+	napi_gro_receive(&q_vector->napi, skb);
 }
 
 /**
@@ -997,7 +942,7 @@ static int i40e_clean_rx_irq_ps(struct i40e_ring *rx_ring, int budget)
 	unsigned int total_rx_bytes = 0, total_rx_packets = 0;
 	u16 rx_packet_len, rx_header_len, rx_sph, rx_hbo;
 	u16 cleaned_count = I40E_DESC_UNUSED(rx_ring);
-	const int current_node = numa_node_id();
+	const int current_node = numa_mem_id();
 	struct i40e_vsi *vsi = rx_ring->vsi;
 	u16 i = rx_ring->next_to_clean;
 	union i40e_rx_desc *rx_desc;
@@ -1067,6 +1012,7 @@ static int i40e_clean_rx_irq_ps(struct i40e_ring *rx_ring, int budget)
 		cleaned_count++;
 		if (rx_hbo || rx_sph) {
 			int len;
+
 			if (rx_hbo)
 				len = I40E_RX_HDR_SIZE;
 			else
@@ -1240,9 +1186,6 @@ static int i40e_clean_rx_irq_1buf(struct i40e_ring *rx_ring, int budget)
 		/* ERR_MASK will only have valid bits if EOP set */
 		if (unlikely(rx_error & BIT(I40E_RX_DESC_ERROR_RXE_SHIFT))) {
 			dev_kfree_skb_any(skb);
-			/* TODO: shouldn't we increment a counter indicating the
-			 * drop?
-			 */
 			continue;
 		}
 
@@ -1274,6 +1217,21 @@ static int i40e_clean_rx_irq_1buf(struct i40e_ring *rx_ring, int budget)
 	return total_rx_packets;
 }
 
+static u32 i40e_buildreg_itr(const int type, const u16 itr)
+{
+	u32 val;
+
+	val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
+	      I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
+	      (type << I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT) |
+	      (itr << I40E_VFINT_DYN_CTLN1_INTERVAL_SHIFT);
+
+	return val;
+}
+
+/* a small macro to shorten up some long lines */
+#define INTREG I40E_VFINT_DYN_CTLN1
+
 /**
  * i40e_update_enable_itr - Update itr and re-enable MSIX interrupt
  * @vsi: the VSI we care about
@@ -1284,55 +1242,67 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi,
 					  struct i40e_q_vector *q_vector)
 {
 	struct i40e_hw *hw = &vsi->back->hw;
-	u16 old_itr;
+	bool rx = false, tx = false;
+	u32 rxval, txval;
 	int vector;
-	u32 val;
 
 	vector = (q_vector->v_idx + vsi->base_vector);
+
+	/* avoid dynamic calculation if in countdown mode OR if
+	 * all dynamic is disabled
+	 */
+	rxval = txval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
+
+	if (q_vector->itr_countdown > 0 ||
+	    (!ITR_IS_DYNAMIC(vsi->rx_itr_setting) &&
+	     !ITR_IS_DYNAMIC(vsi->tx_itr_setting))) {
+		goto enable_int;
+	}
+
 	if (ITR_IS_DYNAMIC(vsi->rx_itr_setting)) {
-		old_itr = q_vector->rx.itr;
-		i40e_set_new_dynamic_itr(&q_vector->rx);
-		if (old_itr != q_vector->rx.itr) {
-			val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
-			I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
-			(I40E_RX_ITR <<
-				I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT) |
-			(q_vector->rx.itr <<
-				I40E_VFINT_DYN_CTLN1_INTERVAL_SHIFT);
-		} else {
-			val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
-			I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
-			(I40E_ITR_NONE <<
-				I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT);
-		}
-		if (!test_bit(__I40E_DOWN, &vsi->state))
-			wr32(hw, I40E_VFINT_DYN_CTLN1(vector - 1), val);
-	} else {
-		i40evf_irq_enable_queues(vsi->back, 1
-			<< q_vector->v_idx);
+		rx = i40e_set_new_dynamic_itr(&q_vector->rx);
+		rxval = i40e_buildreg_itr(I40E_RX_ITR, q_vector->rx.itr);
 	}
 	if (ITR_IS_DYNAMIC(vsi->tx_itr_setting)) {
-		old_itr = q_vector->tx.itr;
-		i40e_set_new_dynamic_itr(&q_vector->tx);
-		if (old_itr != q_vector->tx.itr) {
-			val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
-				I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
-				(I40E_TX_ITR <<
-				   I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT) |
-				(q_vector->tx.itr <<
-				   I40E_VFINT_DYN_CTLN1_INTERVAL_SHIFT);
+		tx = i40e_set_new_dynamic_itr(&q_vector->tx);
+		txval = i40e_buildreg_itr(I40E_TX_ITR, q_vector->tx.itr);
+	}
+	if (rx || tx) {
+		/* get the higher of the two ITR adjustments and
+		 * use the same value for both ITR registers
+		 * when in adaptive mode (Rx and/or Tx)
+		 */
+		u16 itr = max(q_vector->tx.itr, q_vector->rx.itr);
 
-		} else {
-			val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
-				I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
-				(I40E_ITR_NONE <<
-				   I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT);
-		}
-		if (!test_bit(__I40E_DOWN, &vsi->state))
-			wr32(hw, I40E_VFINT_DYN_CTLN1(vector - 1), val);
-	} else {
-		i40evf_irq_enable_queues(vsi->back, BIT(q_vector->v_idx));
+		q_vector->tx.itr = q_vector->rx.itr = itr;
+		txval = i40e_buildreg_itr(I40E_TX_ITR, itr);
+		tx = true;
+		rxval = i40e_buildreg_itr(I40E_RX_ITR, itr);
+		rx = true;
 	}
+
+	/* only need to enable the interrupt once, but need
+	 * to possibly update both ITR values
+	 */
+	if (rx) {
+		/* set the INTENA_MSK_MASK so that this first write
+		 * won't actually enable the interrupt, instead just
+		 * updating the ITR (it's bit 31 PF and VF)
+		 */
+		rxval |= BIT(31);
+		/* don't check _DOWN because interrupt isn't being enabled */
+		wr32(hw, INTREG(vector - 1), rxval);
+	}
+
+enable_int:
+	if (!test_bit(__I40E_DOWN, &vsi->state))
+		wr32(hw, INTREG(vector - 1), txval);
+
+	if (q_vector->itr_countdown)
+		q_vector->itr_countdown--;
+	else
+		q_vector->itr_countdown = ITR_COUNTDOWN_START;
+
 }
 
 /**
@@ -1353,7 +1323,7 @@ int i40evf_napi_poll(struct napi_struct *napi, int budget)
 	bool clean_complete = true;
 	bool arm_wb = false;
 	int budget_per_ring;
-	int cleaned;
+	int work_done = 0;
 
 	if (test_bit(__I40E_DOWN, &vsi->state)) {
 		napi_complete(napi);
@@ -1366,26 +1336,36 @@ int i40evf_napi_poll(struct napi_struct *napi, int budget)
 	i40e_for_each_ring(ring, q_vector->tx) {
 		clean_complete &= i40e_clean_tx_irq(ring, vsi->work_limit);
 		arm_wb |= ring->arm_wb;
+		ring->arm_wb = false;
 	}
 
+	/* Handle case where we are called by netpoll with a budget of 0 */
+	if (budget <= 0)
+		goto tx_only;
+
 	/* We attempt to distribute budget to each Rx queue fairly, but don't
 	 * allow the budget to go below 1 because that would exit polling early.
 	 */
 	budget_per_ring = max(budget/q_vector->num_ringpairs, 1);
 
 	i40e_for_each_ring(ring, q_vector->rx) {
+		int cleaned;
+
 		if (ring_is_ps_enabled(ring))
 			cleaned = i40e_clean_rx_irq_ps(ring, budget_per_ring);
 		else
 			cleaned = i40e_clean_rx_irq_1buf(ring, budget_per_ring);
+
+		work_done += cleaned;
 		/* if we didn't clean as many as budgeted, we must be done */
 		clean_complete &= (budget_per_ring != cleaned);
 	}
 
 	/* If work not completed, return budget and polling will return */
 	if (!clean_complete) {
+tx_only:
 		if (arm_wb)
-			i40e_force_wb(vsi, q_vector);
+			i40evf_force_wb(vsi, q_vector);
 		return budget;
 	}
 
@@ -1393,7 +1373,7 @@ int i40evf_napi_poll(struct napi_struct *napi, int budget)
 		q_vector->arm_wb_state = false;
 
 	/* Work is done so exit the polling mode and re-enable the interrupt */
-	napi_complete(napi);
+	napi_complete_done(napi, work_done);
 	i40e_update_enable_itr(vsi, q_vector);
 	return 0;
 }
@@ -1437,6 +1417,7 @@ static inline int i40evf_tx_prepare_vlan_flags(struct sk_buff *skb,
 	/* else if it is a SW VLAN, check the next protocol and store the tag */
 	} else if (protocol == htons(ETH_P_8021Q)) {
 		struct vlan_hdr *vhdr, _vhdr;
+
 		vhdr = skb_header_pointer(skb, ETH_HLEN, sizeof(_vhdr), &_vhdr);
 		if (!vhdr)
 			return -EINVAL;
@@ -1979,6 +1960,7 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb,
 	u32 td_cmd = 0;
 	u8 hdr_len = 0;
 	int tso;
+
 	if (0 == i40evf_xmit_descriptor_count(skb, tx_ring))
 		return NETDEV_TX_BUSY;
 
@@ -2006,10 +1988,11 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb,
 	else if (tso)
 		tx_flags |= I40E_TX_FLAGS_TSO;
 
-	if (i40e_chk_linearize(skb, tx_flags))
+	if (i40e_chk_linearize(skb, tx_flags)) {
 		if (skb_linearize(skb))
 			goto out_drop;
-
+		tx_ring->tx_stats.tx_linearize++;
+	}
 	skb_tx_timestamp(skb);
 
 	/* always enable CRC insertion offload */