diff options
| author | Abhishek Sahu <absahu@codeaurora.org> | 2017-08-11 17:09:16 +0530 |
|---|---|---|
| committer | Boris Brezillon <boris.brezillon@free-electrons.com> | 2017-08-23 16:49:24 +0200 |
| commit | d8a9b320a26c1ea28e51e4f3ecfb593d5aac2910 (patch) | |
| tree | 0a32edc7e8f79f253ad475fbfc8fc21b64ba6297 /drivers/mtd | |
| parent | 238709b22097a16839078530e0a10812dde86f16 (diff) | |
| download | linux-d8a9b320a26c1ea28e51e4f3ecfb593d5aac2910.tar.bz2 | |
mtd: nand: qcom: fix read failure without complete bootchain
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Diffstat (limited to 'drivers/mtd')
| -rw-r--r-- | drivers/mtd/nand/qcom_nandc.c | 16 |
1 files changed, 12 insertions, 4 deletions
diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c index 0e727d79f2ce..e5cb8f12d5bb 100644 --- a/drivers/mtd/nand/qcom_nandc.c +++ b/drivers/mtd/nand/qcom_nandc.c @@ -109,7 +109,11 @@ #define READ_ADDR 0 /* NAND_DEV_CMD_VLD bits */ -#define READ_START_VLD 0 +#define READ_START_VLD BIT(0) +#define READ_STOP_VLD BIT(1) +#define WRITE_START_VLD BIT(2) +#define ERASE_START_VLD BIT(3) +#define SEQ_READ_START_VLD BIT(4) /* NAND_EBI2_ECC_BUF_CFG bits */ #define NUM_STEPS 0 @@ -148,6 +152,10 @@ #define FETCH_ID 0xb #define RESET_DEVICE 0xd +/* Default Value for NAND_DEV_CMD_VLD */ +#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \ + ERASE_START_VLD | SEQ_READ_START_VLD) + /* * the NAND controller performs reads/writes with ECC in 516 byte chunks. * the driver calls the chunks 'step' or 'codeword' interchangeably @@ -695,8 +703,7 @@ static int nandc_param(struct qcom_nand_host *host) /* configure CMD1 and VLD for ONFI param probing */ nandc_set_reg(nandc, NAND_DEV_CMD_VLD, - (nandc->vld & ~(1 << READ_START_VLD)) - | 0 << READ_START_VLD); + (nandc->vld & ~READ_START_VLD)); nandc_set_reg(nandc, NAND_DEV_CMD1, (nandc->cmd1 & ~(0xFF << READ_ADDR)) | NAND_CMD_PARAM << READ_ADDR); @@ -1995,13 +2002,14 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) { /* kill onenand */ nandc_write(nandc, SFLASHC_BURST_CFG, 0); + nandc_write(nandc, NAND_DEV_CMD_VLD, NAND_DEV_CMD_VLD_VAL); /* enable ADM DMA */ nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN); /* save the original values of these registers */ nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1); - nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD); + nandc->vld = NAND_DEV_CMD_VLD_VAL; return 0; } |