drm/i915/psr: Make PSR registers relative to transcoders

PSR registers are a mess, some have the full address while others just
have the additional offset from psr_mmio_base.

For BDW+ psr_mmio_base is nothing more than TRANSCODER_EDP_OFFSET +
0x800 and using it makes more difficult for people with an PSR
register address or PSR register name from from BSpec as i915 also
don't match the BSpec names.
For HSW psr_mmio_base is _DDI_BUF_CTL_A + 0x800 and PSR registers are
only available in DDIA.

Other reason to make relative to transcoder is that since BDW every
transcoder have PSR registers, so in theory it should be possible to
have PSR enabled in a non-eDP transcoder.

So for BDW+ we can use _TRANS2() to get the register offset of any
PSR register in any transcoder while for HSW we have _HSW_PSR_ADJ
that will calculate the register offset for the single PSR instance,
noting that we are already guarded about trying to enable PSR in other
port than DDIA on HSW by the 'if (dig_port->base.port != PORT_A)' in
intel_psr_compute_config(), this check should only be valid for HSW
and will be changed in future.
PSR2 registers and PSR_EVENT was added after Haswell so that is why
_PSR_ADJ() is not used in some macros.

The only registers that can not be relative to transcoder are
PSR_IMR and PSR_IIR that are not relative to anything, so keeping it
hardcoded. That changed for TGL but it will be handled in another
patch.

Also removing BDW_EDP_PSR_BASE from GVT because it is not used as it
is the only PSR register that GVT have.

v5:
- Macros changed to be more explicit about HSW (Dhinakaran)
- Squashed with the patch that added the tran parameter to the
macros (Dhinakaran)

v6:
- Checking for interruption errors after module reload in the
transcoder that will be used (Dhinakaran)
- Using lowercase to the registers offsets

v7:
- Removing IS_HASWELL() from registers macros(Jani)

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-1-jose.souza@intel.com

1 files changed, 59 insertions, 45 deletions

diff --git a/drivers/gpu/drm/i915/display/intel_psr.c b/drivers/gpu/drm/i915/display/intel_psr.c
index 3bfb720560c2..77232f6bca17 100644
--- a/drivers/gpu/drm/i915/display/intel_psr.c
+++ b/drivers/gpu/drm/i915/display/intel_psr.c
@@ -390,7 +390,7 @@ static void hsw_psr_setup_aux(struct intel_dp *intel_dp)
 
 	BUILD_BUG_ON(sizeof(aux_msg) > 20);
 	for (i = 0; i < sizeof(aux_msg); i += 4)
-		I915_WRITE(EDP_PSR_AUX_DATA(i >> 2),
+		I915_WRITE(EDP_PSR_AUX_DATA(dev_priv->psr.transcoder, i >> 2),
 			   intel_dp_pack_aux(&aux_msg[i], sizeof(aux_msg) - i));
 
 	aux_clock_divider = intel_dp->get_aux_clock_divider(intel_dp, 0);
@@ -401,7 +401,7 @@ static void hsw_psr_setup_aux(struct intel_dp *intel_dp)
 
 	/* Select only valid bits for SRD_AUX_CTL */
 	aux_ctl &= psr_aux_mask;
-	I915_WRITE(EDP_PSR_AUX_CTL, aux_ctl);
+	I915_WRITE(EDP_PSR_AUX_CTL(dev_priv->psr.transcoder), aux_ctl);
 }
 
 static void intel_psr_enable_sink(struct intel_dp *intel_dp)
@@ -491,8 +491,9 @@ static void hsw_activate_psr1(struct intel_dp *intel_dp)
 	if (INTEL_GEN(dev_priv) >= 8)
 		val |= EDP_PSR_CRC_ENABLE;
 
-	val |= I915_READ(EDP_PSR_CTL) & EDP_PSR_RESTORE_PSR_ACTIVE_CTX_MASK;
-	I915_WRITE(EDP_PSR_CTL, val);
+	val |= (I915_READ(EDP_PSR_CTL(dev_priv->psr.transcoder)) &
+		EDP_PSR_RESTORE_PSR_ACTIVE_CTX_MASK);
+	I915_WRITE(EDP_PSR_CTL(dev_priv->psr.transcoder), val);
 }
 
 static void hsw_activate_psr2(struct intel_dp *intel_dp)
@@ -528,9 +529,9 @@ static void hsw_activate_psr2(struct intel_dp *intel_dp)
 	 * PSR2 HW is incorrectly using EDP_PSR_TP1_TP3_SEL and BSpec is
 	 * recommending keep this bit unset while PSR2 is enabled.
 	 */
-	I915_WRITE(EDP_PSR_CTL, 0);
+	I915_WRITE(EDP_PSR_CTL(dev_priv->psr.transcoder), 0);
 
-	I915_WRITE(EDP_PSR2_CTL, val);
+	I915_WRITE(EDP_PSR2_CTL(dev_priv->psr.transcoder), val);
 }
 
 static bool intel_psr2_config_valid(struct intel_dp *intel_dp,
@@ -606,10 +607,9 @@ void intel_psr_compute_config(struct intel_dp *intel_dp,
 
 	/*
 	 * HSW spec explicitly says PSR is tied to port A.
-	 * BDW+ platforms with DDI implementation of PSR have different
-	 * PSR registers per transcoder and we only implement transcoder EDP
-	 * ones. Since by Display design transcoder EDP is tied to port A
-	 * we can safely escape based on the port A.
+	 * BDW+ platforms have a instance of PSR registers per transcoder but
+	 * for now it only supports one instance of PSR, so lets keep it
+	 * hardcoded to PORT_A
 	 */
 	if (dig_port->base.port != PORT_A) {
 		DRM_DEBUG_KMS("PSR condition failed: Port not supported\n");
@@ -649,8 +649,8 @@ static void intel_psr_activate(struct intel_dp *intel_dp)
 	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
 
 	if (INTEL_GEN(dev_priv) >= 9)
-		WARN_ON(I915_READ(EDP_PSR2_CTL) & EDP_PSR2_ENABLE);
-	WARN_ON(I915_READ(EDP_PSR_CTL) & EDP_PSR_ENABLE);
+		WARN_ON(I915_READ(EDP_PSR2_CTL(dev_priv->psr.transcoder)) & EDP_PSR2_ENABLE);
+	WARN_ON(I915_READ(EDP_PSR_CTL(dev_priv->psr.transcoder)) & EDP_PSR_ENABLE);
 	WARN_ON(dev_priv->psr.active);
 	lockdep_assert_held(&dev_priv->psr.lock);
 
@@ -720,19 +720,37 @@ static void intel_psr_enable_source(struct intel_dp *intel_dp,
 	if (INTEL_GEN(dev_priv) < 11)
 		mask |= EDP_PSR_DEBUG_MASK_DISP_REG_WRITE;
 
-	I915_WRITE(EDP_PSR_DEBUG, mask);
+	I915_WRITE(EDP_PSR_DEBUG(dev_priv->psr.transcoder), mask);
 }
 
 static void intel_psr_enable_locked(struct drm_i915_private *dev_priv,
 				    const struct intel_crtc_state *crtc_state)
 {
 	struct intel_dp *intel_dp = dev_priv->psr.dp;
+	u32 val;
 
 	WARN_ON(dev_priv->psr.enabled);
 
 	dev_priv->psr.psr2_enabled = intel_psr2_enabled(dev_priv, crtc_state);
 	dev_priv->psr.busy_frontbuffer_bits = 0;
 	dev_priv->psr.pipe = to_intel_crtc(crtc_state->base.crtc)->pipe;
+	dev_priv->psr.transcoder = crtc_state->cpu_transcoder;
+
+	/*
+	 * If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
+	 * will still keep the error set even after the reset done in the
+	 * irq_preinstall and irq_uninstall hooks.
+	 * And enabling in this situation cause the screen to freeze in the
+	 * first time that PSR HW tries to activate so lets keep PSR disabled
+	 * to avoid any rendering problems.
+	 */
+	val = I915_READ(EDP_PSR_IIR);
+	val &= EDP_PSR_ERROR(edp_psr_shift(dev_priv->psr.transcoder));
+	if (val) {
+		dev_priv->psr.sink_not_reliable = true;
+		DRM_DEBUG_KMS("PSR interruption error set, not enabling PSR\n");
+		return;
+	}
 
 	DRM_DEBUG_KMS("Enabling PSR%s\n",
 		      dev_priv->psr.psr2_enabled ? "2" : "1");
@@ -782,20 +800,27 @@ static void intel_psr_exit(struct drm_i915_private *dev_priv)
 	u32 val;
 
 	if (!dev_priv->psr.active) {
-		if (INTEL_GEN(dev_priv) >= 9)
-			WARN_ON(I915_READ(EDP_PSR2_CTL) & EDP_PSR2_ENABLE);
-		WARN_ON(I915_READ(EDP_PSR_CTL) & EDP_PSR_ENABLE);
+		if (INTEL_GEN(dev_priv) >= 9) {
+			val = I915_READ(EDP_PSR2_CTL(dev_priv->psr.transcoder));
+			WARN_ON(val & EDP_PSR2_ENABLE);
+		}
+
+		val = I915_READ(EDP_PSR_CTL(dev_priv->psr.transcoder));
+		WARN_ON(val & EDP_PSR_ENABLE);
+
 		return;
 	}
 
 	if (dev_priv->psr.psr2_enabled) {
-		val = I915_READ(EDP_PSR2_CTL);
+		val = I915_READ(EDP_PSR2_CTL(dev_priv->psr.transcoder));
 		WARN_ON(!(val & EDP_PSR2_ENABLE));
-		I915_WRITE(EDP_PSR2_CTL, val & ~EDP_PSR2_ENABLE);
+		val &= ~EDP_PSR2_ENABLE;
+		I915_WRITE(EDP_PSR2_CTL(dev_priv->psr.transcoder), val);
 	} else {
-		val = I915_READ(EDP_PSR_CTL);
+		val = I915_READ(EDP_PSR_CTL(dev_priv->psr.transcoder));
 		WARN_ON(!(val & EDP_PSR_ENABLE));
-		I915_WRITE(EDP_PSR_CTL, val & ~EDP_PSR_ENABLE);
+		val &= ~EDP_PSR_ENABLE;
+		I915_WRITE(EDP_PSR_CTL(dev_priv->psr.transcoder), val);
 	}
 	dev_priv->psr.active = false;
 }
@@ -817,10 +842,10 @@ static void intel_psr_disable_locked(struct intel_dp *intel_dp)
 	intel_psr_exit(dev_priv);
 
 	if (dev_priv->psr.psr2_enabled) {
-		psr_status = EDP_PSR2_STATUS;
+		psr_status = EDP_PSR2_STATUS(dev_priv->psr.transcoder);
 		psr_status_mask = EDP_PSR2_STATUS_STATE_MASK;
 	} else {
-		psr_status = EDP_PSR_STATUS;
+		psr_status = EDP_PSR_STATUS(dev_priv->psr.transcoder);
 		psr_status_mask = EDP_PSR_STATUS_STATE_MASK;
 	}
 
@@ -963,7 +988,8 @@ int intel_psr_wait_for_idle(const struct intel_crtc_state *new_crtc_state,
 	 * defensive enough to cover everything.
 	 */
 
-	return __intel_wait_for_register(&dev_priv->uncore, EDP_PSR_STATUS,
+	return __intel_wait_for_register(&dev_priv->uncore,
+					 EDP_PSR_STATUS(dev_priv->psr.transcoder),
 					 EDP_PSR_STATUS_STATE_MASK,
 					 EDP_PSR_STATUS_STATE_IDLE, 2, 50,
 					 out_value);
@@ -979,10 +1005,10 @@ static bool __psr_wait_for_idle_locked(struct drm_i915_private *dev_priv)
 		return false;
 
 	if (dev_priv->psr.psr2_enabled) {
-		reg = EDP_PSR2_STATUS;
+		reg = EDP_PSR2_STATUS(dev_priv->psr.transcoder);
 		mask = EDP_PSR2_STATUS_STATE_MASK;
 	} else {
-		reg = EDP_PSR_STATUS;
+		reg = EDP_PSR_STATUS(dev_priv->psr.transcoder);
 		mask = EDP_PSR_STATUS_STATE_MASK;
 	}
 
@@ -1208,36 +1234,24 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,
  */
 void intel_psr_init(struct drm_i915_private *dev_priv)
 {
-	u32 val;
-
 	if (!HAS_PSR(dev_priv))
 		return;
 
-	dev_priv->psr_mmio_base = IS_HASWELL(dev_priv) ?
-		HSW_EDP_PSR_BASE : BDW_EDP_PSR_BASE;
-
 	if (!dev_priv->psr.sink_support)
 		return;
 
+	if (IS_HASWELL(dev_priv))
+		/*
+		 * HSW don't have PSR registers on the same space as transcoder
+		 * so set this to a value that when subtract to the register
+		 * in transcoder space results in the right offset for HSW
+		 */
+		dev_priv->hsw_psr_mmio_adjust = _SRD_CTL_EDP - _HSW_EDP_PSR_BASE;
+
 	if (i915_modparams.enable_psr == -1)
 		if (INTEL_GEN(dev_priv) < 9 || !dev_priv->vbt.psr.enable)
 			i915_modparams.enable_psr = 0;
 
-	/*
-	 * If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
-	 * will still keep the error set even after the reset done in the
-	 * irq_preinstall and irq_uninstall hooks.
-	 * And enabling in this situation cause the screen to freeze in the
-	 * first time that PSR HW tries to activate so lets keep PSR disabled
-	 * to avoid any rendering problems.
-	 */
-	val = I915_READ(EDP_PSR_IIR);
-	val &= EDP_PSR_ERROR(edp_psr_shift(TRANSCODER_EDP));
-	if (val) {
-		DRM_DEBUG_KMS("PSR interruption error set\n");
-		dev_priv->psr.sink_not_reliable = true;
-	}
-
 	/* Set link_standby x link_off defaults */
 	if (IS_HASWELL(dev_priv) || IS_BROADWELL(dev_priv))
 		/* HSW and BDW require workarounds that we don't implement. */