summaryrefslogtreecommitdiffstats
path: root/drivers/ata
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2010-03-01 13:04:58 -0800
committerLinus Torvalds <torvalds@linux-foundation.org>2010-03-01 13:04:58 -0800
commit379e3a820da171cb1d97e8dccd736a69cebfb7c0 (patch)
treeaef459cf9b4de9b85d357f487bb3e1170c9eea98 /drivers/ata
parent8724fdb53d27d7b59b60c8a399cc67f9abfabb33 (diff)
parenta55ab496ea9c820b7192c15ef1fbf3291edfe638 (diff)
downloadlinux-379e3a820da171cb1d97e8dccd736a69cebfb7c0.tar.bz2
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits) sata_via: Delay on vt6420 when starting ATAPI DMA write ata: Detect Delkin Devices compact flash pata_efar: Enable parallel scanning pata_atiixp: enable parallel scan [libata] pata_atiixp: add locking for parallel scanning [libata] pata_efar: add locking for parallel scanning libata: Pass host flags into the pci helper [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI libata: Allow pata_legacy to be built on non-ISA but PCI systems pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards [libata] pata_at91: fix backslash-continued string pata_via: store UDMA masks in via_isa_bridges table pata_via: fix address setup timings underlocking pata_serverworks: fix error message pata_serverworks: fix PIO setup for the second channel pata_efar: fix secondary port support pata_cypress: fix PIO timings underclocking pata_cs5535: use correct values for PIO1 and PIO2 data timings pata_cmd64x: remove unused definitions ...
Diffstat (limited to 'drivers/ata')
-rw-r--r--drivers/ata/Kconfig4
-rw-r--r--drivers/ata/ahci.c235
-rw-r--r--drivers/ata/ata_generic.c2
-rw-r--r--drivers/ata/ata_piix.c28
-rw-r--r--drivers/ata/libata-core.c17
-rw-r--r--drivers/ata/libata-sff.c50
-rw-r--r--drivers/ata/pata_acpi.c2
-rw-r--r--drivers/ata/pata_ali.c10
-rw-r--r--drivers/ata/pata_amd.c2
-rw-r--r--drivers/ata/pata_artop.c2
-rw-r--r--drivers/ata/pata_at91.c4
-rw-r--r--drivers/ata/pata_atiixp.c14
-rw-r--r--drivers/ata/pata_cmd640.c2
-rw-r--r--drivers/ata/pata_cmd64x.c27
-rw-r--r--drivers/ata/pata_cs5530.c2
-rw-r--r--drivers/ata/pata_cs5535.c4
-rw-r--r--drivers/ata/pata_cs5536.c2
-rw-r--r--drivers/ata/pata_cypress.c12
-rw-r--r--drivers/ata/pata_efar.c22
-rw-r--r--drivers/ata/pata_hpt366.c23
-rw-r--r--drivers/ata/pata_hpt37x.c189
-rw-r--r--drivers/ata/pata_hpt3x2n.c120
-rw-r--r--drivers/ata/pata_it8213.c2
-rw-r--r--drivers/ata/pata_it821x.c2
-rw-r--r--drivers/ata/pata_jmicron.c2
-rw-r--r--drivers/ata/pata_marvell.c4
-rw-r--r--drivers/ata/pata_netcell.c2
-rw-r--r--drivers/ata/pata_ns87410.c2
-rw-r--r--drivers/ata/pata_ns87415.c2
-rw-r--r--drivers/ata/pata_oldpiix.c2
-rw-r--r--drivers/ata/pata_opti.c2
-rw-r--r--drivers/ata/pata_optidma.c2
-rw-r--r--drivers/ata/pata_pcmcia.c2
-rw-r--r--drivers/ata/pata_pdc202xx_old.c17
-rw-r--r--drivers/ata/pata_piccolo.c2
-rw-r--r--drivers/ata/pata_radisys.c2
-rw-r--r--drivers/ata/pata_rz1000.c2
-rw-r--r--drivers/ata/pata_sc1200.c2
-rw-r--r--drivers/ata/pata_serverworks.c7
-rw-r--r--drivers/ata/pata_sil680.c2
-rw-r--r--drivers/ata/pata_sis.c2
-rw-r--r--drivers/ata/pata_sl82c105.c2
-rw-r--r--drivers/ata/pata_triflex.c2
-rw-r--r--drivers/ata/pata_via.c210
-rw-r--r--drivers/ata/sata_via.c23
45 files changed, 657 insertions, 413 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 56c6374a3989..01c52c415bdc 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -446,9 +446,9 @@ config PATA_JMICRON
config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
- depends on ISA && EXPERIMENTAL
+ depends on (ISA || PCI) && EXPERIMENTAL
help
- This option enables support for ISA/VLB bus legacy PATA
+ This option enables support for ISA/VLB/PCI bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
If unsure, say N.
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index a6a736a7dbf2..6bd930b93bcc 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -93,6 +93,9 @@ enum {
AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
AHCI_RX_FIS_SZ,
+ AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
+ AHCI_CMD_TBL_AR_SZ +
+ (AHCI_RX_FIS_SZ * 16),
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
@@ -170,6 +173,7 @@ enum {
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
+ PORT_FBS = 0x40, /* FIS-based Switching */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
@@ -208,6 +212,7 @@ enum {
PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
+ PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
PORT_CMD_PMP = (1 << 17), /* PMP attached */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
@@ -222,6 +227,14 @@ enum {
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
+ PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
+ PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
+ PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
+ PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
+ PORT_FBS_SDE = (1 << 2), /* FBS single device error */
+ PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
+ PORT_FBS_EN = (1 << 0), /* Enable FBS */
+
/* hpriv->flags bits */
AHCI_HFLAG_NO_NCQ = (1 << 0),
AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
@@ -304,6 +317,9 @@ struct ahci_port_priv {
unsigned int ncq_saw_dmas:1;
unsigned int ncq_saw_sdb:1;
u32 intr_mask; /* interrupts to enable */
+ bool fbs_supported; /* set iff FBS is supported */
+ bool fbs_enabled; /* set iff FBS is enabled */
+ int fbs_last_dev; /* save FBS.DEV of last FIS */
/* enclosure management info per PM slot */
struct ahci_em_priv em_priv[EM_MAX_SLOTS];
};
@@ -315,9 +331,12 @@ static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc);
static int ahci_port_start(struct ata_port *ap);
static void ahci_port_stop(struct ata_port *ap);
+static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc);
static void ahci_qc_prep(struct ata_queued_cmd *qc);
static void ahci_freeze(struct ata_port *ap);
static void ahci_thaw(struct ata_port *ap);
+static void ahci_enable_fbs(struct ata_port *ap);
+static void ahci_disable_fbs(struct ata_port *ap);
static void ahci_pmp_attach(struct ata_port *ap);
static void ahci_pmp_detach(struct ata_port *ap);
static int ahci_softreset(struct ata_link *link, unsigned int *class,
@@ -356,10 +375,10 @@ static ssize_t ahci_show_host_version(struct device *dev,
static ssize_t ahci_show_port_cmd(struct device *dev,
struct device_attribute *attr, char *buf);
-DEVICE_ATTR(ahci_host_caps, S_IRUGO, ahci_show_host_caps, NULL);
-DEVICE_ATTR(ahci_host_cap2, S_IRUGO, ahci_show_host_cap2, NULL);
-DEVICE_ATTR(ahci_host_version, S_IRUGO, ahci_show_host_version, NULL);
-DEVICE_ATTR(ahci_port_cmd, S_IRUGO, ahci_show_port_cmd, NULL);
+static DEVICE_ATTR(ahci_host_caps, S_IRUGO, ahci_show_host_caps, NULL);
+static DEVICE_ATTR(ahci_host_cap2, S_IRUGO, ahci_show_host_cap2, NULL);
+static DEVICE_ATTR(ahci_host_version, S_IRUGO, ahci_show_host_version, NULL);
+static DEVICE_ATTR(ahci_port_cmd, S_IRUGO, ahci_show_port_cmd, NULL);
static struct device_attribute *ahci_shost_attrs[] = {
&dev_attr_link_power_management_policy,
@@ -390,7 +409,7 @@ static struct scsi_host_template ahci_sht = {
static struct ata_port_operations ahci_ops = {
.inherits = &sata_pmp_port_ops,
- .qc_defer = sata_pmp_qc_defer_cmd_switch,
+ .qc_defer = ahci_pmp_qc_defer,
.qc_prep = ahci_qc_prep,
.qc_issue = ahci_qc_issue,
.qc_fill_rtf = ahci_qc_fill_rtf,
@@ -570,6 +589,12 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
{ PCI_VDEVICE(INTEL, 0x3b2c), board_ahci }, /* PCH RAID */
{ PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */
+ { PCI_VDEVICE(INTEL, 0x1c02), board_ahci }, /* CPT AHCI */
+ { PCI_VDEVICE(INTEL, 0x1c03), board_ahci }, /* CPT AHCI */
+ { PCI_VDEVICE(INTEL, 0x1c04), board_ahci }, /* CPT RAID */
+ { PCI_VDEVICE(INTEL, 0x1c05), board_ahci }, /* CPT RAID */
+ { PCI_VDEVICE(INTEL, 0x1c06), board_ahci }, /* CPT RAID */
+ { PCI_VDEVICE(INTEL, 0x1c07), board_ahci }, /* CPT RAID */
/* JMicron 360/1/3/5/6, match class to avoid IDE function */
{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -2045,6 +2070,17 @@ static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl)
return si;
}
+static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+
+ if (!sata_pmp_attached(ap) || pp->fbs_enabled)
+ return ata_std_qc_defer(qc);
+ else
+ return sata_pmp_qc_defer_cmd_switch(qc);
+}
+
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
@@ -2083,6 +2119,31 @@ static void ahci_qc_prep(struct ata_queued_cmd *qc)
ahci_fill_cmd_slot(pp, qc->tag, opts);
}
+static void ahci_fbs_dec_intr(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ int retries = 3;
+
+ DPRINTK("ENTER\n");
+ BUG_ON(!pp->fbs_enabled);
+
+ /* time to wait for DEC is not specified by AHCI spec,
+ * add a retry loop for safety.
+ */
+ writel(fbs | PORT_FBS_DEC, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ while ((fbs & PORT_FBS_DEC) && retries--) {
+ udelay(1);
+ fbs = readl(port_mmio + PORT_FBS);
+ }
+
+ if (fbs & PORT_FBS_DEC)
+ dev_printk(KERN_ERR, ap->host->dev,
+ "failed to clear device error\n");
+}
+
static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
{
struct ahci_host_priv *hpriv = ap->host->private_data;
@@ -2091,12 +2152,26 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
struct ata_link *link = NULL;
struct ata_queued_cmd *active_qc;
struct ata_eh_info *active_ehi;
+ bool fbs_need_dec = false;
u32 serror;
- /* determine active link */
- ata_for_each_link(link, ap, EDGE)
- if (ata_link_active(link))
- break;
+ /* determine active link with error */
+ if (pp->fbs_enabled) {
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ int pmp = fbs >> PORT_FBS_DWE_OFFSET;
+
+ if ((fbs & PORT_FBS_SDE) && (pmp < ap->nr_pmp_links) &&
+ ata_link_online(&ap->pmp_link[pmp])) {
+ link = &ap->pmp_link[pmp];
+ fbs_need_dec = true;
+ }
+
+ } else
+ ata_for_each_link(link, ap, EDGE)
+ if (ata_link_active(link))
+ break;
+
if (!link)
link = &ap->link;
@@ -2153,8 +2228,13 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
}
if (irq_stat & PORT_IRQ_IF_ERR) {
- host_ehi->err_mask |= AC_ERR_ATA_BUS;
- host_ehi->action |= ATA_EH_RESET;
+ if (fbs_need_dec)
+ active_ehi->err_mask |= AC_ERR_DEV;
+ else {
+ host_ehi->err_mask |= AC_ERR_ATA_BUS;
+ host_ehi->action |= ATA_EH_RESET;
+ }
+
ata_ehi_push_desc(host_ehi, "interface fatal error");
}
@@ -2169,7 +2249,10 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
if (irq_stat & PORT_IRQ_FREEZE)
ata_port_freeze(ap);
- else
+ else if (fbs_need_dec) {
+ ata_link_abort(link);
+ ahci_fbs_dec_intr(ap);
+ } else
ata_port_abort(ap);
}
@@ -2222,12 +2305,19 @@ static void ahci_port_intr(struct ata_port *ap)
/* If the 'N' bit in word 0 of the FIS is set,
* we just received asynchronous notification.
* Tell libata about it.
+ *
+ * Lack of SNotification should not appear in
+ * ahci 1.2, so the workaround is unnecessary
+ * when FBS is enabled.
*/
- const __le32 *f = pp->rx_fis + RX_FIS_SDB;
- u32 f0 = le32_to_cpu(f[0]);
-
- if (f0 & (1 << 15))
- sata_async_notification(ap);
+ if (pp->fbs_enabled)
+ WARN_ON_ONCE(1);
+ else {
+ const __le32 *f = pp->rx_fis + RX_FIS_SDB;
+ u32 f0 = le32_to_cpu(f[0]);
+ if (f0 & (1 << 15))
+ sata_async_notification(ap);
+ }
}
}
@@ -2321,6 +2411,15 @@ static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
if (qc->tf.protocol == ATA_PROT_NCQ)
writel(1 << qc->tag, port_mmio + PORT_SCR_ACT);
+
+ if (pp->fbs_enabled && pp->fbs_last_dev != qc->dev->link->pmp) {
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ fbs &= ~(PORT_FBS_DEV_MASK | PORT_FBS_DEC);
+ fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET;
+ writel(fbs, port_mmio + PORT_FBS);
+ pp->fbs_last_dev = qc->dev->link->pmp;
+ }
+
writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE);
ahci_sw_activity(qc->dev->link);
@@ -2333,6 +2432,9 @@ static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
struct ahci_port_priv *pp = qc->ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ if (pp->fbs_enabled)
+ d2h_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ;
+
ata_tf_from_fis(d2h_fis, &qc->result_tf);
return true;
}
@@ -2381,6 +2483,71 @@ static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
ahci_kick_engine(ap);
}
+static void ahci_enable_fbs(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs;
+ int rc;
+
+ if (!pp->fbs_supported)
+ return;
+
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN) {
+ pp->fbs_enabled = true;
+ pp->fbs_last_dev = -1; /* initialization */
+ return;
+ }
+
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ return;
+
+ writel(fbs | PORT_FBS_EN, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN) {
+ dev_printk(KERN_INFO, ap->host->dev, "FBS is enabled.\n");
+ pp->fbs_enabled = true;
+ pp->fbs_last_dev = -1; /* initialization */
+ } else
+ dev_printk(KERN_ERR, ap->host->dev, "Failed to enable FBS\n");
+
+ ahci_start_engine(ap);
+}
+
+static void ahci_disable_fbs(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs;
+ int rc;
+
+ if (!pp->fbs_supported)
+ return;
+
+ fbs = readl(port_mmio + PORT_FBS);
+ if ((fbs & PORT_FBS_EN) == 0) {
+ pp->fbs_enabled = false;
+ return;
+ }
+
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ return;
+
+ writel(fbs & ~PORT_FBS_EN, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN)
+ dev_printk(KERN_ERR, ap->host->dev, "Failed to disable FBS\n");
+ else {
+ dev_printk(KERN_INFO, ap->host->dev, "FBS is disabled.\n");
+ pp->fbs_enabled = false;
+ }
+
+ ahci_start_engine(ap);
+}
+
static void ahci_pmp_attach(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
@@ -2391,6 +2558,8 @@ static void ahci_pmp_attach(struct ata_port *ap)
cmd |= PORT_CMD_PMP;
writel(cmd, port_mmio + PORT_CMD);
+ ahci_enable_fbs(ap);
+
pp->intr_mask |= PORT_IRQ_BAD_PMP;
writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
}
@@ -2401,6 +2570,8 @@ static void ahci_pmp_detach(struct ata_port *ap)
struct ahci_port_priv *pp = ap->private_data;
u32 cmd;
+ ahci_disable_fbs(ap);
+
cmd = readl(port_mmio + PORT_CMD);
cmd &= ~PORT_CMD_PMP;
writel(cmd, port_mmio + PORT_CMD);
@@ -2492,20 +2663,40 @@ static int ahci_pci_device_resume(struct pci_dev *pdev)
static int ahci_port_start(struct ata_port *ap)
{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
struct device *dev = ap->host->dev;
struct ahci_port_priv *pp;
void *mem;
dma_addr_t mem_dma;
+ size_t dma_sz, rx_fis_sz;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
- mem = dmam_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma,
- GFP_KERNEL);
+ /* check FBS capability */
+ if ((hpriv->cap & HOST_CAP_FBS) && sata_pmp_supported(ap)) {
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd = readl(port_mmio + PORT_CMD);
+ if (cmd & PORT_CMD_FBSCP)
+ pp->fbs_supported = true;
+ else
+ dev_printk(KERN_WARNING, dev,
+ "The port is not capable of FBS\n");
+ }
+
+ if (pp->fbs_supported) {
+ dma_sz = AHCI_PORT_PRIV_FBS_DMA_SZ;
+ rx_fis_sz = AHCI_RX_FIS_SZ * 16;
+ } else {
+ dma_sz = AHCI_PORT_PRIV_DMA_SZ;
+ rx_fis_sz = AHCI_RX_FIS_SZ;
+ }
+
+ mem = dmam_alloc_coherent(dev, dma_sz, &mem_dma, GFP_KERNEL);
if (!mem)
return -ENOMEM;
- memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
+ memset(mem, 0, dma_sz);
/*
* First item in chunk of DMA memory: 32-slot command table,
@@ -2523,8 +2714,8 @@ static int ahci_port_start(struct ata_port *ap)
pp->rx_fis = mem;
pp->rx_fis_dma = mem_dma;
- mem += AHCI_RX_FIS_SZ;
- mem_dma += AHCI_RX_FIS_SZ;
+ mem += rx_fis_sz;
+ mem_dma += rx_fis_sz;
/*
* Third item: data area for storing a single command
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 12e26c3c68e3..33fb614f9784 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -155,7 +155,7 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
return rc;
pcim_pin_device(dev);
}
- return ata_pci_sff_init_one(dev, ppi, &generic_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &generic_sht, NULL, 0);
}
static struct pci_device_id ata_generic[] = {
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 6f3f2257d0f0..c33806654e46 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -173,6 +173,7 @@ static int piix_sidpr_scr_read(struct ata_link *link,
unsigned int reg, u32 *val);
static int piix_sidpr_scr_write(struct ata_link *link,
unsigned int reg, u32 val);
+static bool piix_irq_check(struct ata_port *ap);
#ifdef CONFIG_PM
static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
static int piix_pci_device_resume(struct pci_dev *pdev);
@@ -291,6 +292,14 @@ static const struct pci_device_id piix_pci_tbl[] = {
{ 0x8086, 0x3b2d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (PCH) */
{ 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
+ /* SATA Controller IDE (CPT) */
+ { 0x8086, 0x1c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
+ /* SATA Controller IDE (CPT) */
+ { 0x8086, 0x1c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
+ /* SATA Controller IDE (CPT) */
+ { 0x8086, 0x1c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (CPT) */
+ { 0x8086, 0x1c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
{ } /* terminate list */
};
@@ -309,8 +318,13 @@ static struct scsi_host_template piix_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
-static struct ata_port_operations piix_pata_ops = {
+static struct ata_port_operations piix_sata_ops = {
.inherits = &ata_bmdma32_port_ops,
+ .sff_irq_check = piix_irq_check,
+};
+
+static struct ata_port_operations piix_pata_ops = {
+ .inherits = &piix_sata_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = piix_set_piomode,
.set_dmamode = piix_set_dmamode,
@@ -328,10 +342,6 @@ static struct ata_port_operations ich_pata_ops = {
.set_dmamode = ich_set_dmamode,
};
-static struct ata_port_operations piix_sata_ops = {
- .inherits = &ata_bmdma32_port_ops,
-};
-
static struct ata_port_operations piix_sidpr_sata_ops = {
.inherits = &piix_sata_ops,
.hardreset = sata_std_hardreset,
@@ -962,6 +972,14 @@ static int piix_sidpr_scr_write(struct ata_link *link,
return 0;
}
+static bool piix_irq_check(struct ata_port *ap)
+{
+ if (unlikely(!ap->ioaddr.bmdma_addr))
+ return false;
+
+ return ap->ops->bmdma_status(ap) & ATA_DMA_INTR;
+}
+
#ifdef CONFIG_PM
static int piix_broken_suspend(void)
{
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 6728328f3bea..9c77b0d1a9d0 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3211,6 +3211,7 @@ const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
int ata_timing_compute(struct ata_device *adev, unsigned short speed,
struct ata_timing *t, int T, int UT)
{
+ const u16 *id = adev->id;
const struct ata_timing *s;
struct ata_timing p;
@@ -3228,14 +3229,18 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
* PIO/MW_DMA cycle timing.
*/
- if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
+ if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
memset(&p, 0, sizeof(p));
+
if (speed >= XFER_PIO_0 && speed <= XFER_SW_DMA_0) {
- if (speed <= XFER_PIO_2) p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO];
- else p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO_IORDY];
- } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) {
- p.cycle = adev->id[ATA_ID_EIDE_DMA_MIN];
- }
+ if (speed <= XFER_PIO_2)
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
+ else if ((speed <= XFER_PIO_4) ||
+ (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
+ } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ p.cycle = id[ATA_ID_EIDE_DMA_MIN];
+
ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
}
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 730ef3c384ca..02441fd57e9e 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -1763,24 +1763,50 @@ irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
unsigned int i;
- unsigned int handled = 0;
+ unsigned int handled = 0, polling = 0;
unsigned long flags;
/* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
spin_lock_irqsave(&host->lock, flags);
for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap;
+ struct ata_port *ap = host->ports[i];
+ struct ata_queued_cmd *qc;
- ap = host->ports[i];
- if (ap &&
- !(ap->flags & ATA_FLAG_DISABLED)) {
- struct ata_queued_cmd *qc;
+ if (unlikely(ap->flags & ATA_FLAG_DISABLED))
+ continue;
- qc = ata_qc_from_tag(ap, ap->link.active_tag);
- if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) &&
- (qc->flags & ATA_QCFLAG_ACTIVE))
+ qc = ata_qc_from_tag(ap, ap->link.active_tag);
+ if (qc) {
+ if (!(qc->tf.flags & ATA_TFLAG_POLLING))
handled |= ata_sff_host_intr(ap, qc);
+ else
+ polling |= 1 << i;
+ }
+ }
+
+ /*
+ * If no port was expecting IRQ but the controller is actually
+ * asserting IRQ line, nobody cared will ensue. Check IRQ
+ * pending status if available and clear spurious IRQ.
+ */
+ if (!handled) {
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ if (polling & (1 << i))
+ continue;
+
+ if (!ap->ops->sff_irq_check ||
+ !ap->ops->sff_irq_check(ap))
+ continue;
+
+ if (printk_ratelimit())
+ ata_port_printk(ap, KERN_INFO,
+ "clearing spurious IRQ\n");
+
+ ap->ops->sff_check_status(ap);
+ ap->ops->sff_irq_clear(ap);
}
}
@@ -3011,6 +3037,7 @@ EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
* @ppi: array of port_info, must be enough for two ports
* @sht: scsi_host_template to use when registering the host
* @host_priv: host private_data
+ * @hflag: host flags
*
* This is a helper function which can be called from a driver's
* xxx_init_one() probe function if the hardware uses traditional
@@ -3031,8 +3058,8 @@ EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
* Zero on success, negative on errno-based value on error.
*/
int ata_pci_sff_init_one(struct pci_dev *pdev,
- const struct ata_port_info * const *ppi,
- struct scsi_host_template *sht, void *host_priv)
+ const struct ata_port_info * const *ppi,
+ struct scsi_host_template *sht, void *host_priv, int hflag)
{
struct device *dev = &pdev->dev;
const struct ata_port_info *pi = NULL;
@@ -3067,6 +3094,7 @@ int ata_pci_sff_init_one(struct pci_dev *pdev,
if (rc)
goto out;
host->private_data = host_priv;
+ host->flags |= hflag;
pci_set_master(pdev);
rc = ata_pci_sff_activate_host(host, ata_sff_interrupt, sht);
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index d8f35fe44421..294f3020a78a 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -259,7 +259,7 @@ static int pacpi_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
return rc;
pcim_pin_device(pdev);
}
- return ata_pci_sff_init_one(pdev, ppi, &pacpi_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &pacpi_sht, NULL, 0);
}
static const struct pci_device_id pacpi_pci_tbl[] = {
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 9434114b2ca8..dc61b72f751c 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -159,8 +159,7 @@ static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int o
* ali_program_modes - load mode registers
* @ap: ALi channel to load
* @adev: Device the timing is for
- * @cmd: Command timing
- * @data: Data timing
+ * @t: timing data
* @ultra: UDMA timing or zero for off
*
* Loads the timing registers for cmd/data and disable UDMA if
@@ -202,8 +201,7 @@ static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, stru
* @ap: ATA interface
* @adev: ATA device
*
- * Program the ALi registers for PIO mode. FIXME: add timings for
- * PIO5.
+ * Program the ALi registers for PIO mode.
*/
static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -237,7 +235,7 @@ static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: ATA device
*
- * FIXME: MWDMA timings
+ * Program the ALi registers for DMA mode.
*/
static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev)
@@ -585,7 +583,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ppi[0] = &info_20_udma;
}
- return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 567f3f72774e..d95eca9c547e 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -574,7 +574,7 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
}
/* And fire it up */
- return ata_pci_sff_init_one(pdev, ppi, &amd_sht, hpriv);
+ return ata_pci_sff_init_one(pdev, ppi, &amd_sht, hpriv, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index d332cfdb0f30..4d066d6c30fa 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -421,7 +421,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
BUG_ON(ppi[0] == NULL);
- return ata_pci_sff_init_one(pdev, ppi, &artop_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &artop_sht, NULL, 0);
}
static const struct pci_device_id artop_pci_tbl[] = {
diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 41c94b1ae493..376dd380b43c 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -153,8 +153,8 @@ static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
/* Compute ATA timing and set it to SMC */
ret = ata_timing_compute(adev, adev->pio_mode, &timing, 1000, 0);
if (ret) {
- dev_warn(ap->dev, "Failed to compute ATA timing %d, \
- set PIO_0 timing\n", ret);
+ dev_warn(ap->dev, "Failed to compute ATA timing %d, "
+ "set PIO_0 timing\n", ret);
set_smc_timing(ap->dev, info, &initial_timing);
} else {
set_smc_timing(ap->dev, info, &timing);
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index ae4454d4e955..cbaf2eddac6b 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -1,7 +1,7 @@
/*
* pata_atiixp.c - ATI PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * (C) 2009 Bartlomiej Zolnierkiewicz
+ * (C) 2009-2010 Bartlomiej Zolnierkiewicz
*
* Based on
*
@@ -46,6 +46,8 @@ static int atiixp_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA40;
}
+static DEFINE_SPINLOCK(atiixp_lock);
+
/**
* atiixp_set_pio_timing - set initial PIO mode data
* @ap: ATA interface
@@ -88,7 +90,10 @@ static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev,
static void atiixp_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
+ unsigned long flags;
+ spin_lock_irqsave(&atiixp_lock, flags);
atiixp_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0);
+ spin_unlock_irqrestore(&atiixp_lock, flags);
}
/**
@@ -108,6 +113,9 @@ static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev)
int dma = adev->dma_mode;
int dn = 2 * ap->port_no + adev->devno;
int wanted_pio;
+ unsigned long flags;
+
+ spin_lock_irqsave(&atiixp_lock, flags);
if (adev->dma_mode >= XFER_UDMA_0) {
u16 udma_mode_data;
@@ -145,6 +153,7 @@ static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev)
if (adev->pio_mode != wanted_pio)
atiixp_set_pio_timing(ap, adev, wanted_pio);
+ spin_unlock_irqrestore(&atiixp_lock, flags);
}
/**
@@ -237,7 +246,8 @@ static int atiixp_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (!pci_test_config_bits(pdev, &atiixp_enable_bits[i]))
ppi[i] = &ata_dummy_port_info;
- return ata_pci_sff_init_one(pdev, ppi, &atiixp_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &atiixp_sht, NULL,
+ ATA_HOST_PARALLEL_SCAN);
}
static const struct pci_device_id atiixp[] = {
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 5acf9fa9b39f..6cd5d5dd9e3b 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -223,7 +223,7 @@ static int cmd640_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
cmd640_hardware_init(pdev);
- return ata_pci_sff_init_one(pdev, ppi, &cmd640_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &cmd640_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 0efb1f58f255..4c81a71b8877 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -2,6 +2,7 @@
* pata_cmd64x.c - CMD64x PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@lxorguk.ukuu.org.uk>
+ * (C) 2009-2010 Bartlomiej Zolnierkiewicz
*
* Based upon
* linux/drivers/ide/pci/cmd64x.c Version 1.30 Sept 10, 2002
@@ -39,11 +40,7 @@
enum {
CFR = 0x50,
- CFR_INTR_CH0 = 0x02,
- CNTRL = 0x51,
- CNTRL_DIS_RA0 = 0x40,
- CNTRL_DIS_RA1 = 0x80,
- CNTRL_ENA_2ND = 0x08,
+ CFR_INTR_CH0 = 0x04,
CMDTIM = 0x52,
ARTTIM0 = 0x53,
DRWTIM0 = 0x54,
@@ -53,9 +50,6 @@ enum {
ARTTIM23_DIS_RA2 = 0x04,
ARTTIM23_DIS_RA3 = 0x08,
ARTTIM23_INTR_CH1 = 0x10,
- ARTTIM2 = 0x57,
- ARTTIM3 = 0x57,
- DRWTIM23 = 0x58,
DRWTIM2 = 0x58,
BRST = 0x59,
DRWTIM3 = 0x5b,
@@ -63,14 +57,11 @@ enum {
MRDMODE = 0x71,
MRDMODE_INTR_CH0 = 0x04,
MRDMODE_INTR_CH1 = 0x08,
- MRDMODE_BLK_CH0 = 0x10,
- MRDMODE_BLK_CH1 = 0x20,
BMIDESR0 = 0x72,
UDIDETCR0 = 0x73,
DTPR0 = 0x74,
BMIDECR1 = 0x78,
BMIDECSR = 0x79,
- BMIDESR1 = 0x7A,
UDIDETCR1 = 0x7B,
DTPR1 = 0x7C
};
@@ -130,8 +121,14 @@ static void cmd64x_set_timing(struct ata_port *ap, struct ata_device *adev, u8 m
if (pair) {
struct ata_timing tp;
+
ata_timing_compute(pair, pair->pio_mode, &tp, T, 0);
ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
+ if (pair->dma_mode) {
+ ata_timing_compute(pair, pair->dma_mode,
+ &tp, T, 0);
+ ata_timing_merge(&tp, &t, &t, ATA_TIMING_SETUP);
+ }
}
}
@@ -147,7 +144,9 @@ static void cmd64x_set_timing(struct ata_port *ap, struct ata_device *adev, u8 m
/* Now convert the clocks into values we can actually stuff into
the chip */
- if (t.recover > 1)
+ if (t.recover == 16)
+ t.recover = 0;
+ else if (t.recover > 1)
t.recover--;
else
t.recover = 15;
@@ -245,7 +244,7 @@ static void cmd648_bmdma_stop(struct ata_queued_cmd *qc)
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 dma_intr;
int dma_mask = ap->port_no ? ARTTIM23_INTR_CH1 : CFR_INTR_CH0;
- int dma_reg = ap->port_no ? ARTTIM2 : CFR;
+ int dma_reg = ap->port_no ? ARTTIM23 : CFR;
ata_bmdma_stop(qc);
@@ -368,7 +367,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
#endif
- return ata_pci_sff_init_one(pdev, ppi, &cmd64x_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &cmd64x_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index c974b05e4129..738ad2e14a97 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -324,7 +324,7 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ppi[1] = &info_palmax_secondary;
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(pdev, ppi, &cs5530_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &cs5530_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index 71cef9a962d4..a02e6459fdcc 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -100,7 +100,7 @@ static int cs5535_cable_detect(struct ata_port *ap)
static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
static const u16 pio_timings[5] = {
- 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
+ 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131
};
static const u16 pio_cmd_timings[5] = {
0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
@@ -198,7 +198,7 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
rdmsr(ATAC_CH0D1_PIO, timings, dummy);
if (CS5535_BAD_PIO(timings))
wrmsr(ATAC_CH0D1_PIO, 0xF7F4F7F4UL, 0);
- return ata_pci_sff_init_one(dev, ppi, &cs5535_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &cs5535_sht, NULL, 0);
}
static const struct pci_device_id cs5535[] = {
diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c
index ffee3978ec83..914ae3506ff5 100644
--- a/drivers/ata/pata_cs5536.c
+++ b/drivers/ata/pata_cs5536.c
@@ -260,7 +260,7 @@ static int cs5536_init_one(struct pci_dev *dev, const struct pci_device_id *id)
return -ENODEV;
}
- return ata_pci_sff_init_one(dev, ppi, &cs5536_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &cs5536_sht, NULL, 0);
}
static const struct pci_device_id cs5536[] = {
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 8fb040bf7361..0fcc096b8dac 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -62,14 +62,16 @@ static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
return;
}
- time_16 = clamp_val(t.recover, 0, 15) | (clamp_val(t.active, 0, 15) << 4);
- time_8 = clamp_val(t.act8b, 0, 15) | (clamp_val(t.rec8b, 0, 15) << 4);
+ time_16 = clamp_val(t.recover - 1, 0, 15) |
+ (clamp_val(t.active - 1, 0, 15) << 4);
+ time_8 = clamp_val(t.act8b - 1, 0, 15) |
+ (clamp_val(t.rec8b - 1, 0, 15) << 4);
if (adev->devno == 0) {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0x0F; /* Mask bits */
- addr |= clamp_val(t.setup, 0, 15);
+ addr |= clamp_val(t.setup - 1, 0, 15);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
@@ -79,7 +81,7 @@ static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0xF0; /* Mask bits */
- addr |= (clamp_val(t.setup, 0, 15) << 4);
+ addr |= (clamp_val(t.setup - 1, 0, 15) << 4);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
@@ -136,7 +138,7 @@ static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *i
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
- return ata_pci_sff_init_one(pdev, ppi, &cy82c693_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &cy82c693_sht, NULL, 0);
}
static const struct pci_device_id cy82c693[] = {
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index b2e71e6473ed..3bac0e079691 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -2,7 +2,7 @@
* pata_efar.c - EFAR PIIX clone controller driver
*
* (C) 2005 Red Hat
- * (C) 2009 Bartlomiej Zolnierkiewicz
+ * (C) 2009-2010 Bartlomiej Zolnierkiewicz
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
@@ -68,6 +68,8 @@ static int efar_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA80;
}
+static DEFINE_SPINLOCK(efar_lock);
+
/**
* efar_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
@@ -84,7 +86,9 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
unsigned int pio = adev->pio_mode - XFER_PIO_0;
struct pci_dev *dev = to_pci_dev(ap->host->dev);
unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+ unsigned long flags;
u16 idetm_data;
+ u8 udma_enable;
int control = 0;
/*
@@ -107,6 +111,8 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE */
+ spin_lock_irqsave(&efar_lock, flags);
+
pci_read_config_word(dev, idetm_port, &idetm_data);
/* Set PPE, IE, and TIME as appropriate */
@@ -131,6 +137,11 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
idetm_data |= 0x4000; /* Ensure SITRE is set */
pci_write_config_word(dev, idetm_port, idetm_data);
+
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+ udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
+ pci_write_config_byte(dev, 0x48, udma_enable);
+ spin_unlock_irqrestore(&efar_lock, flags);
}
/**
@@ -151,6 +162,7 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
u16 master_data;
u8 speed = adev->dma_mode;
int devid = adev->devno + 2 * ap->port_no;
+ unsigned long flags;
u8 udma_enable;
static const /* ISP RTC */
@@ -160,6 +172,8 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{ 2, 1 },
{ 2, 3 }, };
+ spin_lock_irqsave(&efar_lock, flags);
+
pci_read_config_word(dev, master_port, &master_data);
pci_read_config_byte(dev, 0x48, &udma_enable);
@@ -217,6 +231,7 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
pci_write_config_word(dev, master_port, master_data);
}
pci_write_config_byte(dev, 0x48, udma_enable);
+ spin_unlock_irqrestore(&efar_lock, flags);
}
static struct scsi_host_template efar_sht = {
@@ -256,13 +271,14 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
.udma_mask = ATA_UDMA4,
.port_ops = &efar_ops,
};
- const struct ata_port_info *ppi[] = { &info, NULL };
+ const struct ata_port_info *ppi[] = { &info, &info };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &efar_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &efar_sht, NULL,
+ ATA_HOST_PARALLEL_SCAN);
}
static const struct pci_device_id efar_pci_tbl[] = {
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 0bd48e8f21bd..af49bfb57247 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -11,9 +11,7 @@
*
*
* TODO
- * Maybe PLL mode
- * Look into engine reset on timeout errors. Should not be
- * required.
+ * Look into engine reset on timeout errors. Should not be required.
*/
@@ -27,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt366"
-#define DRV_VERSION "0.6.7"
+#define DRV_VERSION "0.6.8"
struct hpt_clock {
u8 xfer_mode;
@@ -207,17 +205,8 @@ static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
{
struct hpt_clock *clocks = ap->host->private_data;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- u32 addr2 = 0x51 + 4 * ap->port_no;
+ u32 addr = 0x40 + 4 * adev->devno;
u32 mask, reg;
- u8 fast;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
/* determine timing mask and find matching clock entry */
if (mode < XFER_MW_DMA_0)
@@ -240,9 +229,9 @@ static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
* on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
* problems handling I/O errors later.
*/
- pci_read_config_dword(pdev, addr1, &reg);
+ pci_read_config_dword(pdev, addr, &reg);
reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
- pci_write_config_dword(pdev, addr1, reg);
+ pci_write_config_dword(pdev, addr, reg);
}
/**
@@ -372,7 +361,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
break;
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv);
+ return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 4224cfccedef..8839307a64cf 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.6.14"
+#define DRV_VERSION "0.6.15"
struct hpt_clock {
u8 xfer_speed;
@@ -39,25 +39,24 @@ struct hpt_chip {
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 FIFO enable. Only for PIO.
*/
static struct hpt_clock hpt37x_timings_33[] = {
@@ -384,20 +383,12 @@ static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt370_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -409,11 +400,31 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast |= 0x01;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ * hpt370_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt370_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -421,33 +432,12 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x02;
- fast |= 0x01;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt370_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -461,24 +451,25 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u8 dma_stat = ioread8(ap->ioaddr.bmdma_addr + 2);
- u8 dma_cmd;
void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+ u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+ u8 dma_cmd;
- if (dma_stat & 0x01) {
+ if (dma_stat & ATA_DMA_ACTIVE) {
udelay(20);
- dma_stat = ioread8(bmdma + 2);
+ dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
}
- if (dma_stat & 0x01) {
+ if (dma_stat & ATA_DMA_ACTIVE) {
/* Clear the engine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(10);
/* Stop DMA */
- dma_cmd = ioread8(bmdma );
- iowrite8(dma_cmd & 0xFE, bmdma);
+ dma_cmd = ioread8(bmdma + ATA_DMA_CMD);
+ iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD);
/* Clear Error */
- dma_stat = ioread8(bmdma + 2);
- iowrite8(dma_stat | 0x06 , bmdma + 2);
+ dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+ iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR,
+ bmdma + ATA_DMA_STATUS);
/* Clear the engine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(10);
@@ -486,20 +477,12 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
ata_bmdma_stop(qc);
}
-/**
- * hpt372_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -510,13 +493,32 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt372_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
- printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt372_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -524,33 +526,12 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt372_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -1006,7 +987,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data);
+ return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
}
static const struct pci_device_id hpt37x[] = {
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index dd26bc73bd9a..01457b266f3d 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.8"
+#define DRV_VERSION "0.3.10"
enum {
HPT_PCI_FAST = (1 << 31),
@@ -45,25 +45,24 @@ struct hpt_chip {
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 FIFO enable. Only for PIO.
*/
/* 66MHz DPLL clocks */
@@ -161,20 +160,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt3x2n_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -185,11 +176,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt3x2n_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt3x2n_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt3x2n_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt3x2n_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -197,32 +209,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt3x2n_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt3x2n_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -544,19 +536,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
- if (pci_mhz > 60) {
+ if (pci_mhz > 60)
hpriv = (void *)(PCI66 | USE_DPLL);
- /*
- * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
- * the MISC. register to stretch the UltraDMA Tss timing.
- * NOTE: This register is only writeable via I/O space.
- */
- if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
- outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
- }
+
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+ outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv);
+ return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
}
static const struct pci_device_id hpt3x2n[] = {
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index 8f3325adceb3..f971f0de88e6 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -273,7 +273,7 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &it8213_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &it8213_sht, NULL, 0);
}
static const struct pci_device_id it8213_pci_tbl[] = {
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index edc5c1fed150..9bde1cb5f981 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -932,7 +932,7 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
else
ppi[0] = &info_smart;
}
- return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 3a1474ac8838..565e01e6ac7c 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -144,7 +144,7 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
};
const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_sff_init_one(pdev, ppi, &jmicron_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &jmicron_sht, NULL, 0);
}
static const struct pci_device_id jmicron_pci_tbl[] = {
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 950da39cae3d..e8ca02e5a71d 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -147,13 +147,13 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
if (pdev->device == 0x6101)
ppi[1] = &ata_dummy_port_info;
-#if defined(CONFIG_AHCI) || defined(CONFIG_AHCI_MODULE)
+#if defined(CONFIG_SATA_AHCI) || defined(CONFIG_SATA_AHCI_MODULE)
if (!marvell_pata_active(pdev)) {
printk(KERN_INFO DRV_NAME ": PATA port not active, deferring to AHCI driver.\n");
return -ENODEV;
}
#endif
- return ata_pci_sff_init_one(pdev, ppi, &marvell_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &marvell_sht, NULL, 0);
}
static const struct pci_device_id marvell_pci_tbl[] = {
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index f0d52f72f5bb..94f979a7f4f7 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -82,7 +82,7 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
ata_pci_bmdma_clear_simplex(pdev);
/* And let the library code do the work */
- return ata_pci_sff_init_one(pdev, port_info, &netcell_sht, NULL);
+ return ata_pci_sff_init_one(pdev, port_info, &netcell_sht, NULL, 0);
}
static const struct pci_device_id netcell_pci_tbl[] = {
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index ca53fac06717..2110863bb3db 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -148,7 +148,7 @@ static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &ns87410_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_sff_init_one(dev, ppi, &ns87410_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &ns87410_sht, NULL, 0);
}
static const struct pci_device_id ns87410[] = {
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index 061aa1c41a48..830431f036a1 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -380,7 +380,7 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
ns87415_fixup(pdev);
- return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL, 0);
}
static const struct pci_device_id ns87415_pci_tbl[] = {
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 9a8687db6b2d..5f6aba7eb0dd 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -248,7 +248,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &oldpiix_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &oldpiix_sht, NULL, 0);
}
static const struct pci_device_id oldpiix_pci_tbl[] = {
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 99eddda2d2e5..00c5a02a94fc 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -172,7 +172,7 @@ static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0);
}
static const struct pci_device_id opti[] = {
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 86885a445f97..76b7d12b1e8d 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -429,7 +429,7 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (optiplus_with_udma(dev))
ppi[0] = &info_82c700_udma;
- return ata_pci_sff_init_one(dev, ppi, &optidma_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &optidma_sht, NULL, 0);
}
static const struct pci_device_id optidma[] = {
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index 1b392c9e8531..36103531feeb 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -136,7 +136,7 @@ static unsigned int ata_data_xfer_8bit(struct ata_device *dev,
*
*/
-void pcmcia_8bit_drain_fifo(struct ata_queued_cmd *qc)
+static void pcmcia_8bit_drain_fifo(struct ata_queued_cmd *qc)
{
int count;
struct ata_port *ap;
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 2f3c9bed63d9..9ac0897cf8b0 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -2,7 +2,7 @@
* pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@lxorguk.ukuu.org.uk>
- * (C) 2007,2009 Bartlomiej Zolnierkiewicz
+ * (C) 2007,2009,2010 Bartlomiej Zolnierkiewicz
*
* Based in part on linux/drivers/ide/pci/pdc202xx_old.c
*
@@ -35,6 +35,15 @@ static int pdc2026x_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA80;
}
+static void pdc202xx_exec_command(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+
+ iowrite8(tf->command, ap->ioaddr.command_addr);
+ ndelay(400);
+}
+
/**
* pdc202xx_configure_piomode - set chip PIO timing
* @ap: ATA interface
@@ -271,6 +280,8 @@ static struct ata_port_operations pdc2024x_port_ops = {
.cable_detect = ata_cable_40wire,
.set_piomode = pdc202xx_set_piomode,
.set_dmamode = pdc202xx_set_dmamode,
+
+ .sff_exec_command = pdc202xx_exec_command,
};
static struct ata_port_operations pdc2026x_port_ops = {
@@ -284,6 +295,8 @@ static struct ata_port_operations pdc2026x_port_ops = {
.dev_config = pdc2026x_dev_config,
.port_start = pdc2026x_port_start,
+
+ .sff_exec_command = pdc202xx_exec_command,
};
static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
@@ -324,7 +337,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
return -ENODEV;
}
}
- return ata_pci_sff_init_one(dev, ppi, &pdc202xx_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &pdc202xx_sht, NULL, 0);
}
static const struct pci_device_id pdc202xx[] = {
diff --git a/drivers/ata/pata_piccolo.c b/drivers/ata/pata_piccolo.c
index bfe0180f3efa..981615414849 100644
--- a/drivers/ata/pata_piccolo.c
+++ b/drivers/ata/pata_piccolo.c
@@ -95,7 +95,7 @@ static int ata_tosh_init_one(struct pci_dev *dev, const struct pci_device_id *id
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
/* Just one port for the moment */
- return ata_pci_sff_init_one(dev, ppi, &tosh_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &tosh_sht, NULL, 0);
}
static struct pci_device_id ata_tosh[] = {
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 4fd25e737d9a..fc9602229acb 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -227,7 +227,7 @@ static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *e
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &radisys_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &radisys_sht, NULL, 0);
}
static const struct pci_device_id radisys_pci_tbl[] = {
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index 2932998fc4c6..4a454a88aa9d 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -95,7 +95,7 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
printk_once(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
if (rz1000_fifo_disable(pdev) == 0)
- return ata_pci_sff_init_one(pdev, ppi, &rz1000_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &rz1000_sht, NULL, 0);
printk(KERN_ERR DRV_NAME ": failed to disable read-ahead on chipset..\n");
/* Not safe to use so skip */
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 3bbed8322ecf..dfecc6f964b0 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -237,7 +237,7 @@ static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
};
const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_sff_init_one(dev, ppi, &sc1200_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &sc1200_sht, NULL, 0);
}
static const struct pci_device_id sc1200[] = {
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index beaed12d50e4..9524d54035f7 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -1,6 +1,7 @@
/*
* pata_serverworks.c - Serverworks PATA for new ATA layer
* (C) 2005 Red Hat Inc
+ * (C) 2010 Bartlomiej Zolnierkiewicz
*
* based upon
*
@@ -253,7 +254,7 @@ static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev
if (serverworks_is_csb(pdev)) {
pci_read_config_word(pdev, 0x4A, &csb5_pio);
csb5_pio &= ~(0x0F << devbits);
- pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits));
+ pci_write_config_word(pdev, 0x4A, csb5_pio | (pio << devbits));
}
}
@@ -327,7 +328,7 @@ static int serverworks_fixup_osb4(struct pci_dev *pdev)
pci_dev_put(isa_dev);
return 0;
}
- printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n");
+ printk(KERN_WARNING DRV_NAME ": Unable to find bridge.\n");
return -ENODEV;
}
@@ -459,7 +460,7 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
ata_pci_bmdma_clear_simplex(pdev);
- return ata_pci_sff_init_one(pdev, ppi, &serverworks_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &serverworks_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index a2ace48a4610..c6c589c23ffc 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -356,7 +356,7 @@ static int __devinit sil680_init_one(struct pci_dev *pdev,
IRQF_SHARED, &sil680_sht);
use_ioports:
- return ata_pci_sff_init_one(pdev, ppi, &sil680_sht, NULL);
+ return ata_pci_sff_init_one(pdev, ppi, &sil680_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 5c30d56dec84..b6708032f321 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -826,7 +826,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
sis_fixup(pdev, chipset);
- return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset);
+ return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 29f733c32066..733b042a7469 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -316,7 +316,7 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
- return ata_pci_sff_init_one(dev, ppi, &sl82c105_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &sl82c105_sht, NULL, 0);
}
static const struct pci_device_id sl82c105[] = {
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index f1f13ff222fd..48f50600ed2a 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -201,7 +201,7 @@ static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(dev, ppi, &triflex_sht, NULL);
+ return ata_pci_sff_init_one(dev, ppi, &triflex_sht, NULL, 0);
}
static const struct pci_device_id triflex[] = {
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 0d97890af681..3059ec017de3 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -22,6 +22,7 @@
* VIA VT8233c - UDMA100
* VIA VT8235 - UDMA133
* VIA VT8237 - UDMA133
+ * VIA VT8237A - UDMA133
* VIA VT8237S - UDMA133
* VIA VT8251 - UDMA133
*
@@ -64,26 +65,15 @@
#define DRV_NAME "pata_via"
#define DRV_VERSION "0.3.4"
-/*
- * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
- * driver.
- */
-
enum {
- VIA_UDMA = 0x007,
- VIA_UDMA_NONE = 0x000,
- VIA_UDMA_33 = 0x001,
- VIA_UDMA_66 = 0x002,
- VIA_UDMA_100 = 0x003,
- VIA_UDMA_133 = 0x004,
- VIA_BAD_PREQ = 0x010, /* Crashes if PREQ# till DDACK# set */
- VIA_BAD_CLK66 = 0x020, /* 66 MHz clock doesn't work correctly */
- VIA_SET_FIFO = 0x040, /* Needs to have FIFO split set */
- VIA_NO_UNMASK = 0x080, /* Doesn't work with IRQ unmasking on */
- VIA_BAD_ID = 0x100, /* Has wrong vendor ID (0x1107) */
- VIA_BAD_AST = 0x200, /* Don't touch Address Setup Timing */
- VIA_NO_ENABLES = 0x400, /* Has no enablebits */
- VIA_SATA_PATA = 0x800, /* SATA/PATA combined configuration */
+ VIA_BAD_PREQ = 0x01, /* Crashes if PREQ# till DDACK# set */
+ VIA_BAD_CLK66 = 0x02, /* 66 MHz clock doesn't work correctly */
+ VIA_SET_FIFO = 0x04, /* Needs to have FIFO split set */
+ VIA_NO_UNMASK = 0x08, /* Doesn't work with IRQ unmasking on */
+ VIA_BAD_ID = 0x10, /* Has wrong vendor ID (0x1107) */
+ VIA_BAD_AST = 0x20, /* Don't touch Address Setup Timing */
+ VIA_NO_ENABLES = 0x40, /* Has no enablebits */
+ VIA_SATA_PATA = 0x80, /* SATA/PATA combined configuration */
};
enum {
@@ -99,40 +89,37 @@ static const struct via_isa_bridge {
u16 id;
u8 rev_min;
u8 rev_max;
- u16 flags;
+ u8 udma_mask;
+ u8 flags;
} via_isa_bridges[] = {
- { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
- { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 |
- VIA_BAD_AST | VIA_SATA_PATA },
- { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
- { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES },
- { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES },
- { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, VIA_UDMA_100 },
- { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, VIA_UDMA_66 },
- { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
- { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, VIA_UDMA_66 },
- { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, VIA_UDMA_33 | VIA_SET_FIFO | VIA_BAD_PREQ },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, VIA_UDMA_NONE | VIA_SET_FIFO },
- { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK },
- { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
- { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST },
+ { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
+ { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
+ { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, ATA_UDMA5, },
+ { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, ATA_UDMA4, },
+ { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
+ { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, ATA_UDMA4, },
+ { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, ATA_UDMA2, VIA_SET_FIFO | VIA_BAD_PREQ },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, 0x00, VIA_SET_FIFO },
+ { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK },
+ { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
+ { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ NULL }
};
@@ -191,10 +178,10 @@ static int via_cable_detect(struct ata_port *ap) {
return ATA_CBL_SATA;
/* Early chips are 40 wire */
- if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
+ if (config->udma_mask < ATA_UDMA4)
return ATA_CBL_PATA40;
/* UDMA 66 chips have only drive side logic */
- else if ((config->flags & VIA_UDMA) < VIA_UDMA_100)
+ else if (config->udma_mask < ATA_UDMA5)
return ATA_CBL_PATA_UNK;
/* UDMA 100 or later */
pci_read_config_dword(pdev, 0x50, &ata66);
@@ -229,11 +216,10 @@ static int via_pre_reset(struct ata_link *link, unsigned long deadline)
/**
- * via_do_set_mode - set initial PIO mode data
+ * via_do_set_mode - set transfer mode data
* @ap: ATA interface
* @adev: ATA device
* @mode: ATA mode being programmed
- * @tdiv: Clocks per PCI clock
* @set_ast: Set to program address setup
* @udma_type: UDMA mode/format of registers
*
@@ -244,17 +230,27 @@ static int via_pre_reset(struct ata_link *link, unsigned long deadline)
* on the two channels.
*/
-static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mode, int tdiv, int set_ast, int udma_type)
+static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev,
+ int mode, int set_ast, int udma_type)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_device *peer = ata_dev_pair(adev);
struct ata_timing t, p;
- static int via_clock = 33333; /* Bus clock in kHZ - ought to be tunable one day */
+ static int via_clock = 33333; /* Bus clock in kHZ */
unsigned long T = 1000000000 / via_clock;
- unsigned long UT = T/tdiv;
+ unsigned long UT = T;
int ut;
int offset = 3 - (2*ap->port_no) - adev->devno;
+ switch (udma_type) {
+ case ATA_UDMA4:
+ UT = T / 2; break;
+ case ATA_UDMA5:
+ UT = T / 3; break;
+ case ATA_UDMA6:
+ UT = T / 4; break;
+ }
+
/* Calculate the timing values we require */
ata_timing_compute(adev, mode, &t, T, UT);
@@ -273,7 +269,7 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
pci_read_config_byte(pdev, 0x4C, &setup);
setup &= ~(3 << shift);
- setup |= clamp_val(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */
+ setup |= (clamp_val(t.setup, 1, 4) - 1) << shift;
pci_write_config_byte(pdev, 0x4C, setup);
}
@@ -284,22 +280,20 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1));
/* Load the UDMA bits according to type */
- switch(udma_type) {
- default:
- /* BUG() ? */
- /* fall through */
- case 33:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
- break;
- case 66:
- ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
- break;
- case 100:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
- break;
- case 133:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
- break;
+ switch (udma_type) {
+ case ATA_UDMA2:
+ default:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
+ break;
+ case ATA_UDMA4:
+ ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
+ break;
+ case ATA_UDMA5:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
+ break;
+ case ATA_UDMA6:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
+ break;
}
/* Set UDMA unless device is not UDMA capable */
@@ -325,22 +319,16 @@ static void via_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
- int mode = config->flags & VIA_UDMA;
- static u8 tclock[5] = { 1, 1, 2, 3, 4 };
- static u8 udma[5] = { 0, 33, 66, 100, 133 };
- via_do_set_mode(ap, adev, adev->pio_mode, tclock[mode], set_ast, udma[mode]);
+ via_do_set_mode(ap, adev, adev->pio_mode, set_ast, config->udma_mask);
}
static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
- int mode = config->flags & VIA_UDMA;
- static u8 tclock[5] = { 1, 1, 2, 3, 4 };
- static u8 udma[5] = { 0, 33, 66, 100, 133 };
- via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]);
+ via_do_set_mode(ap, adev, adev->dma_mode, set_ast, config->udma_mask);
}
/**
@@ -604,33 +592,29 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
via_config_fifo(pdev, config->flags);
/* Clock set up */
- switch(config->flags & VIA_UDMA) {
- case VIA_UDMA_NONE:
- if (config->flags & VIA_NO_UNMASK)
- ppi[0] = &via_mwdma_info_borked;
- else
- ppi[0] = &via_mwdma_info;
- break;
- case VIA_UDMA_33:
- ppi[0] = &via_udma33_info;
- break;
- case VIA_UDMA_66:
- ppi[0] = &via_udma66_info;
- /* The 66 MHz devices require we enable the clock */
- pci_read_config_dword(pdev, 0x50, &timing);
- timing |= 0x80008;
- pci_write_config_dword(pdev, 0x50, timing);
- break;
- case VIA_UDMA_100:
- ppi[0] = &via_udma100_info;
- break;
- case VIA_UDMA_133:
- ppi[0] = &via_udma133_info;
- break;
- default:
- WARN_ON(1);
- return -ENODEV;
- }
+ switch (config->udma_mask) {
+ case 0x00:
+ if (config->flags & VIA_NO_UNMASK)
+ ppi[0] = &via_mwdma_info_borked;
+ else
+ ppi[0] = &via_mwdma_info;
+ break;
+ case ATA_UDMA2:
+ ppi[0] = &via_udma33_info;
+ break;
+ case ATA_UDMA4:
+ ppi[0] = &via_udma66_info;
+ break;
+ case ATA_UDMA5:
+ ppi[0] = &via_udma100_info;
+ break;
+ case ATA_UDMA6:
+ ppi[0] = &via_udma133_info;
+ break;
+ default:
+ WARN_ON(1);
+ return -ENODEV;
+ }
if (config->flags & VIA_BAD_CLK66) {
/* Disable the 66MHz clock on problem devices */
@@ -640,7 +624,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
}
/* We have established the device type, now fire it up */
- return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config);
+ return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config, 0);
}
#ifdef CONFIG_PM
@@ -667,7 +651,7 @@ static int via_reinit_one(struct pci_dev *pdev)
via_config_fifo(pdev, config->flags);
- if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
+ if (config->udma_mask == ATA_UDMA4) {
/* The 66 MHz devices require we enable the clock */
pci_read_config_dword(pdev, 0x50, &timing);
timing |= 0x80008;
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 02efd9a83d26..08f65492cc81 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -40,11 +40,13 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
+#include <scsi/scsi.h>
+#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "sata_via"
-#define DRV_VERSION "2.4"
+#define DRV_VERSION "2.6"
/*
* vt8251 is different from other sata controllers of VIA. It has two
@@ -80,6 +82,7 @@ static int vt8251_scr_write(struct ata_link *link, unsigned int scr, u32 val);
static void svia_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
static void svia_noop_freeze(struct ata_port *ap);
static int vt6420_prereset(struct ata_link *link, unsigned long deadline);
+static void vt6420_bmdma_start(struct ata_queued_cmd *qc);
static int vt6421_pata_cable_detect(struct ata_port *ap);
static void vt6421_set_pio_mode(struct ata_port *ap, struct ata_device *adev);
static void vt6421_set_dma_mode(struct ata_port *ap, struct ata_device *adev);
@@ -121,6 +124,7 @@ static struct ata_port_operations vt6420_sata_ops = {
.inherits = &svia_base_ops,
.freeze = svia_noop_freeze,
.prereset = vt6420_prereset,
+ .bmdma_start = vt6420_bmdma_start,
};
static struct ata_port_operations vt6421_pata_ops = {
@@ -377,6 +381,17 @@ static int vt6420_prereset(struct ata_link *link, unsigned long deadline)
return 0;
}
+static void vt6420_bmdma_start(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ if ((qc->tf.command == ATA_CMD_PACKET) &&
+ (qc->scsicmd->sc_data_direction == DMA_TO_DEVICE)) {
+ /* Prevents corruption on some ATAPI burners */
+ ata_sff_pause(ap);
+ }
+ ata_bmdma_start(qc);
+}
+
static int vt6421_pata_cable_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -392,14 +407,16 @@ static void vt6421_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const u8 pio_bits[] = { 0xA8, 0x65, 0x65, 0x31, 0x20 };
- pci_write_config_byte(pdev, PATA_PIO_TIMING, pio_bits[adev->pio_mode - XFER_PIO_0]);
+ pci_write_config_byte(pdev, PATA_PIO_TIMING - adev->devno,
+ pio_bits[adev->pio_mode - XFER_PIO_0]);
}
static void vt6421_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const u8 udma_bits[] = { 0xEE, 0xE8, 0xE6, 0xE4, 0xE2, 0xE1, 0xE0, 0xE0 };
- pci_write_config_byte(pdev, PATA_UDMA_TIMING, udma_bits[adev->dma_mode - XFER_UDMA_0]);
+ pci_write_config_byte(pdev, PATA_UDMA_TIMING - adev->devno,
+ udma_bits[adev->dma_mode - XFER_UDMA_0]);
}
static const unsigned int svia_bar_sizes[] = {